ProLights Wireless battery operated portable uplighter Manuale utente

Marca: ProLights

Modello: Wireless battery operated portable uplighter

Categoria: Stroboscopi

Tipo: Manuale utente

Questo manuale è adatto anche per

Wireless battery operated portable uplighter, 4x12W RGBWAP/FC LEDs

USER MANUAL

MANUALE UTENTE

SMARTBATHEX

EN - IT

PORTABLE BATTERY-POWERED

UPLIGHTER

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

SMARTBATHEX

Packing content

• SMARTBATHEX

• Power cable

• IR Remote controller

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

General information

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic setup

3. 3 Recharge

3. 4 Menu structure

3. 5 Auto Show

3. 6 Static color

3. 7 Sound mode

3. 8 Manual color

3. 9 Dimmer

3. 10 Operation through the IRC controller

3. 11 Master/Slave mode with DMX signal cable

3. 12 Master/Slave with wireless signal

3. 13 Operation with app SmartColors

3. 14 Operation with WIFIBOX

3. 15 Limiter option

3. 16 Linking

3. 17 DMX mode

3. 18 DMX addressing

3. 19 Connection of the DMX line

3. 20 Construction of the DMX termination

3. 21 DMX control

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Troubleshooting

Warranty

SMARTBATHEX

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with

• Supply voltage of this product is DC24V; never connect directly to AC22V. Leave servicing to skilled

personnel only. Never make any modications on the unit not described in this instruction manual,

otherwise you will risk an electric shock.

• Connection of the power adapter must be made to a power supply system tted with ecient earth-

ing (Class I appliance according to standard EN 6598-1). It is, moreover, recommended to protect the

supply lines of the units from indirect contact and/or shorting to earth by using appropriately sized

residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electri-

cal installer. Check that the voltage correspond to those for which the unit is designed as given on the

electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places subject to excessive humidity.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• This product is not intended for permanent installation.

• Do not touch the product’s housing when operating because it may be very hot.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

SMARTBATHEX

- 1 - INTRODUCTION

1.1 DESCRIPTION

SMARTBATHEX is a portable battery-powered uplighter designed as accent luminaire for all kind of events.

SMARTBATHEX is equipped with a lithium battery pack and a built-in WiFi module for cable- free operation.

The ultra- compact and lightweight design makes this projector truly portable and rechargeable countless

times without “memory eect “. The internal battery has an autonomy for 12 hours in color change mode

and up to 8 hours in full output, while the charging time is only 5 hours. The light source is composed of

4x12W high-power RGBWAP LEDs / fullcolor for a color calibration in the full-spectrum and the extract-

able foot allows you to adjust the angle of the beam to assist tracking operations. The transmission of the

DMX signal is via WiFi technology, the transmission unit WIFIBOX is compatible with any DMX controller or

through the application SMARTCOLORS available for any Android or IOS smartphone.

1.2 TECHNICAL SPECIFICATIONS

Light source and optics

• 4x12W RGBWAP/FC LED

• Lux @ 3 m: 810

• Energy-saving LEDs featuring more vivid colours and lower power consumption compared to tradi-

tional lamps

• Colour synthesis: RGBWAP/FC color mixing (>16 million colours) for a limitless colour range

• White temperature presets: 3200K~10000K

• Beam angle: 25°

• Field angle: 40°

• LEDs average life span: >50’000 h

Electronics and features

• Several DMX selectable congurations (6, 8, 12 channels) for advanced or basic controlling

- 6 channels: RGBWAP

- 8 channels: dimmer, RGBWAP, strobe

- 12 channels: dimmer, RGBWAP, macro, strobo, auto programs, programs speed, dimmer curve

• WDMX: Built-in Wi receiver

• IR controller: infra-red sensor controlled by remote

• 4 char LED display user interface for auto programs execution, static colour mode, creation of custom

shows

• 4 dierent dimming curves available

• Auto mode: built-in programs with execution speed adjustment

• Manual color mode: manual adjustment of color

• Static colour mode: selection of static colour

• Sound mode: music activation through internal microphone, sensitivity control

• Master/Slave mode for stand-alone operations of more units

• Linear and “stepless” transition between DMX values

• Flicker free operations (400Hz)

• Silent operations, due to natural cooling of the peculiar chassis and to absence of fans

Structure and Power supply

• Protection: IP44

• Sturdy die-cast aluminium body conceived for long-time durability and demanding applications

• Tempered glass front panel

SMARTBATHEX

• Battery: 24V, Lithium

• Battery autonomy: 12 hours (color change mode), 8 hours (permanent white full-on)

• Recharge time: 5 hours max

• LED battery status indicator

• Load/Storage battery switch

• Dmx connections: XLR 3p Input/Output

• Ergonomic carrying handle for transportation and positioning

• Adjustable foot support for tilt regulation (up to 20°)

• Power unit: 100-240V 50/60Hz

• Working temperature: 0/+35°

• Weight: 3,4 kg

• Dimensions (WxHxD): 137.8x184x145 mm

137,8 184

145

Technical drawing

Fig.1

SMARTBATHEX

1.3 OPERATING ELEMENTS AND CONNECTIONS

Fig.2

Bottom panel

Side panel

1. MICROPHONE to control the show by the

external audio signal.

2. CONTROL PANEL with display and 4 button

used to access the control panel functions

and manage them.

3. AUTO SYNC/ CLEAR button for WiFi mode

4. CHARGE BATTERY LED

5. Adjustable foot support for tilt regulation

6. ON/OFF SWITCH

7. DMX IN (3-pole XLR):

1 = ground, 2 = DMX -, 3 = DMX +

8. POWER IN mains plug for connection to a

socket (100-240V 50/60Hz) via the supplied

mains cable. The support for the mains fuse

is located near the mains plug. Only replace a

blown fuse by one of the same type.

9. DMX OUT (3-pole XLR):

1= ground, 2 = DMX -, 3 = DMX +

10. POWER OUT: connect to supply power to the

next unit.

SMARTBATHEX

- 2 - INSTALLATION

2.1 MOUNTING

SMARTBATHEX may be set up on a solid and even surface. The unit can also be mounted upside down to a

cross arm. For xing, stable mounting clips are required. The mounting place must be of sucient stability

and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

IMPORTANT

Always additionally secure the projector with the safety rope from falling down. For this purpose, fasten

the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.

Fig.3

THREADED HOLES M12

SMARTBATHEX

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Switch on the SMARTBATHEX with the power switch (If the battery charge is very low, connect the sup-

plied main cable to a socket (100-240V~/50-60Hz). The unit is ready for operation and can be operated via

a DMX controller or it independently performs its show program in succession.

After operation, switch o the unit with the power switch.

NOTE - The battery life indicators are the 4 small green LEDs on either side of the “AUTO” button. The indi-

cators show how much battery life remains available.

3.2 BASIC SETUP

The SMARTBATHEX has a LED display and 4 buttons for access to the functions of the control panel (g. 4).

Fig.4 - Functions of the buttons

MENU UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Scrolls up the list of options or

selects a higher value

Scrolls down the list of

options or selects a lower

value

Activates a menu option or a

selected value

3.3 RECHARGE

To recharge SMARTBATHEX, plug the power cable into a mains socket (100-240V~/50-60Hz). During

charging the LED indicates green to show that the battery is charging.

The charging time are 5 hours and autonomy is 12 hours (color change mode) or 8 hours (permanent

white full-on).

NOTE - The battery charges whenever the product is plugged into a power source. If the product is plugged

in and not in operation, make sure the ON/OFF switch is in the OFF position.

SMARTBATHEX

3.4 MENU STRUCTURE

DMX Personality and

Starting Address

6 CH

d1 - d512

Selects DMX personality and DMX starting value8 CH

d1 - d512

12 CH

d1 - d512

2 Static Colors C--

C1 - C63 Selects 1 of 63 static colors

3 Auto Programs P--

P1 - P4 Selects 1 of 4 auto programs

4 Programs Speed S--

S1 - S100 Sets auto program speed (slow to fast)

5 Sound Active Snd Selects Sound Active mode

6 Sound Sensitivity SenS

u0 - u100 Sets sound sensitivity (low to high)

7 Custom Color Mixing U--

r0 - r255 Red (0-100%)

g0 - g255 Green (0-100%)

b0 - b255 Blue (0-100%)

A0 - A255 Amber (0-100%)

W0 - W255 White (0-100%)

P0 - P255 UV (0-100%)

8 Dimmer dIM

OFF OFF: Dimmer speed o

dIM1 DIM1: Dimmer speed fast

dIM2 DIM2: Dimmer speed middle

dIM3 DIM3: Dimmer speed slow

9 Infrared SET

Turns infrared on or o

OFF

10 2.4GHz WiFi Setting S-tr

drAS

drAU Automatically select receive frequency

drCH

dr1 - dr16 Manually select receive frequency

dtAS

dtAU Automatically select transmit frequency

dtCH

dt1 - dt16 Manually select transmit frequency

11 Limiter Limi

ON Turns limiter on, enabling extended battery life

OFF Turns limiter o, disabling extended battery life

SMARTBATHEX

3.5 AUTO SHOW

This xture has a built-in automatic program. To access this, please see the below instructions:

• Press the button MENU so many times until shows P-- , then press the button ENTER.

• Using UP/DOWN button, select one of the programs P1 - P4 .

• Press the button ENTER to conrm.

• Press the button MENU until S-- appears on the display.

• Use the button UP/DOWN to select the auto programs speed S001 - S100 (slow-fast).

• Press the button ENTER save the setting.

3.6 STATIC COLOR

This xture has the ability to accept custom static color settings. Access these chases via the control panel

on the back of the xture.

• Press the button MENU so many times until shows C-- , then press the button ENTER.

• Using UP/DOWN button, select one of the programs C1 - C63 .

• Press the button ENTER to conrm.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.7 SOUND MODE

• Press the button MENU so many times until the display shows Snd .

• Press the button ENTER to conrm.

• You can set the microphone sensitivity pressing the button MENU so many times until the display show

Sens

• Using the button UP/DOWN, select the desired value sensitivity (slow-fast) u0 - u100 .

• Press the button ENTER to conrm.

3.8 MANUAL COLOR

This mode allows to combine the colors red, green, blue amber white and purple (r, g, b, A, W, P).

• Press the button MENU so many times until the display shows U-- , then press the button ENTER.

• Select the color r, g, b, A, W, P through the buttons UP/DOWN.

• Press the button ENTER to conrm.

• Using UP/DOWN button, select the desired color value 000 - 255 .

• Press ENTER button to continue to the next color.

• Continue until the desired mix is obtained.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.9 DIMMER

• Enter in Dimmer mode to select specic dimming curve, press the button MENU so many times until

shows dIM, and press the button ENTER to conrm.

• Press the button UP/DOWN to select OFF - dIM1 - dIM2 - dIM3.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

SMARTBATHEX

Fig.5

IRC REMOTE

BLACK

OUT

AUTO

STROBE SPEED

SOUND

SENSI-

TIVITY

MANUAL

FADE

SNAP

G B

7 8 9

UV W

3.10 OPERATION THROUGH THE IRC CONTROLLER

To control the SMARTBATHEX with the infrared remote control:

• Press the button MENU repeatedly until SET , then press button ENTER

to conrm.

• Using UP/DOWN button to select On or OFF to enable or disable the in-

frared remote control.

• Press the button ENTER to conrm the chose.

NOTE - Make sure to point the controller directly at the receiver on the

product.

Automatic Mode

Automatic Mode will enable you to run the automatic programs on the

product.

To turn on Automatic Mode:

1. Press AUTO on the controller.

2. Press + or – to choose between the dierent auto programs.

To adjust the speed of the automatic program:

3. Press SPEED on the controller.

4. Press %.

5. Press + or – to either increase or decrease the speed of the program.

Sound Active Mode

Sound Active Mode will enable the product to respond to the music.

To turn on Sound Active mode:

1. Press SOUND on the controller.

To adjust sound sensitivity in Sound Active mode:

2. Press SENSITIVITY on the controller.

3. Press %.

4. Press + or – to either increase or decrease sound sensitivity.

Manual Color Control

To choose a specic color with the controller:

1. Press MANUAL on the controller.

2. Press any number between 0-9 to choose your color.

To manually control the RGB percentage:

3. Press MANUAL on the controller.

4. Press R, G, or B to choose your color.

5. Press + or – to increase or decrease the percentage of each color.

Miscellaneous Operation

To adjust the strobe rate of the program:

1. Press STROBE on the controller.

2. Press + or – to increase or decrease the strobe rate.

3. Press STROBE again to turn o the strobe.

To change the switching eect of the program:

• Press FADE/SNAP on the controller.

• Fade will slowly switch the eect. Snap will rapidly switch the eect.

To black out the lights:

• Press BLACK OUT on the controller.

SMARTBATHEX

• This will turn o all the lights until the button is pressed again.

NOTE - The controller will not respond to any inputs when Black Out is activated. If the remote does not

respond when a button is pressed, try pressing BLACK OUT. You may have inadvertently activated BLACK

OUT.

3.11 MASTER/SLAVE MODE WITH DMX SIGNAL CABLE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the rst unit in line; other units will work as slave.

• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last xture (see page 16).

• Use any one of the standalone modes for the master unit.

• Set the slaves to the same DMX modes.

3.12 MASTER/SLAVE MODE WITH WIRELESS SIGNAL

This mode allows you to wirelessly connect more units SMARTBATHEX, without a controller. The rst unit,

transmitter signal, it will be set as master and the others, receivers, as slave.

Wireless communication between devices can be congured in two ways:

Manual transmit/receive mode

On Master unit:

• Press the MENU button so many times until the display shows S-tr then press the ENTER button.

• Press the UP/DOWN button and select dtCH. Press the ENTER button to conrm.

• Press the UP/DOWN button, select one of the transmitting signal dt 1 - dt 16.

• Press the ENTER button for save the setting.

On Slave unit:

• Press the MENU button so many times until the display shows S-tr. Press the ENTER button to conrm.

• Press the UP/DOWN button and select drCH. Press the ENTER button to conrm.

• Press the UP/DOWN button, select one of the transmitting signal dr 1 - dr 16.

• Press the ENTER button for save the setting.

Auto transmit/receive mode

On Master unit:

• Press the MENU button so many times until the display shows S-tr then press the ENTER button.

• Press the UP/DOWN button and select dtAS. Press the ENTER button to conrm.

• Press the ENTER button again to conrm dtAU.

On Slave unit:

• Press the MENU button so many times until the display shows S-tr.

• Press the ENTER button to conrm.

• Press the UP/DOWN button and select drAS.

• Press the ENTER button to conrm.

• Press the ENTER button again to conrm drAU.

On Master unit:

• Hold the AUTO button.

On Slave unit:

• Hold the AUTO button (always hold AUTO button on Master unit).

• Wait 5 seconds and release the AUTO button on Slave unit.

NOTE - Use any one of the standalone modes for the master unit. Set the slaves to the same DMX modes.

SMARTBATHEX

Fig.6 - Conguration Master/Slave mode

SLAVE

MASTER

IRC REMOTE

BLACK

OUT

AUTO

STROBE SPEED

SOUND

SENSI-

TIVITY

MANUAL

FADE

SNAP

G B

7 8 9

UV W

SMARTBATHEX (MASTER): SIGNAL INPUT

1) DMX (with a DMX Controller)

2) Control panel on device

3) IR remote controller

SMARTBATHEX (MASTER):

TRANSMITTER MODE

(type of channel for data wireless

communication)

1) Manual Channel --> dtCH

2) Auto Channel --> dtAU

SMARTBATHEX (SLAVE): RECEIVER MODE

1) drCH --> MASTER UNIT sets on Manual Channel

2) drAU --> MASTER UNIT sets on Auto Channel

Note: To work in the right way, all SMARTBATHEX must be congured with the same DMX address/mode.

3.13 OPERATION WITH APP “SMARTCOLORS”

Important: WIFIBOX hardware is required to use this app.

WIFIBOX is a new-generation light control system, conceived to obtain an easy and versatile platform for

LED projectors. The signal transmission is managed wired and wireless (through Wi-Fi), both in input and

output, even allowing to control the xtures through a smartphones applications “Smarcolors”, available

for IOS and Android devices. Before using the application, check that all devices are properly congured

with WIFIBOX. For device’s conguration refer to the WIFIBOX manual available on “www.musiclights.it”.

Fig.7

SMARTBATHEX

Fig.8 - Conguration with WIFIBOX

3.14 OPERATION WITH WIFIBOX

This mode allows you to wirelessly connect more units SMARTBATHEX, all managed through a unit WIFI-

BOX (sold separately). For the unit WIFIBOX, transmitter signal, will set the input signal, WIFI or DMX. For

the conguration of the devices refer to the manual of WIFIBOX available on “www.musiclights.it”.

3.15 LIMITER OPTION

The SMARTBATHEX has a limiter option that decreases the power output and extends battery life when

more than 4 colors are turned on. This option is set in the control panel.

To select whether the limiter is on or o, follow the instructions below:

• Press the button MENU repeatedly until Limi , then press button ENTER to conrm.

• Using UP/DOWN button to select On or OFF to activate or deactivate the limiter option.

• Press the button ENTER to conrm the chose.

WIFIBOX: SIGNAL INPUT

1) WIFI (with SmartColors App)

2) DMX (with a DMX Controller)

WIFIBOX: TRANSMITTER MODE

(type of channel for data wireless

communication)

1) Manual Channel

2) Auto Channel

SMARTBATHEX: RECEIVER MODE

1) drCH --> WIFIBOX sets on Manual Channel

2) drAU --> WIFIBOX sets on Auto Channel

SMARTBATHEX

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

6 33 33-38 39 45 51

8 33 33-40 41 49 57

12 33 33-44 45 57 69

3.16 LINKING

1. Connect the DMX OUT of the master unit via 3-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

3.17 DMX MODE

• Press the button MENU so many times until shows, CH6, CH8 or CH12 and press the button ENTER to

conrm.

• Press the button UP/DOWN to select the desired DMX address d001 - d512. Press and hold to scroll quick-

ly. Press ENTER button to store.

The tables on page 17 indicate the operating mode and DMX value. The SMARTBATHEX is equipped with

3 pole XLR connections.

3.18 DMX ADDRESSING

To able to operate the SMARTBATHEX with a light controller, adjust the DMX start address for the rst a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX

channel, adjust the start address 33 on the SMARTBATHEX.

The other functions of the light eect panel are then automatically assigned to the following addresses. At

the next page an example with the start address 33 is shown below:

DMX512 Controller

DMX Address: 33 DMX Address: 51DMX Address: 39 DMX Address: 45

Fig.9 - Example 6 DMX channels conguration

. . . . . . . . . . . .

SMARTBATHEX

Fig.10

Fig.11

3.19 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120 imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.20 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Example:

3 pin XLR connector

SMARTBATHEX

3.21 DMX CONTROL

12 CHANNELS

MODE

FUNCTION DMX

Value

12 Ch

DIMMER

0~100% 000 - 255

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

AMBER

0~100% 000 - 255

WHITE

0~100% 000 - 255

PURPLE

0~100% 000 - 255

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

MANUAL COLOR + COLOR TEMPERATURE

No Function

R: 100% / G: 0-100% / B: 0%

R: 100-0% / G: 100% / B: 0%

R: 0% / G: 100% / B: 0-100%

R: 0% / G: 100-0% / B: 100%

R: 0-100% / G: 0% / B: 100%

R: 100% / G: 0% / B: 100-0%

R: 100% / G: 0-100% / B: 0-100%

R: 100-0% / G: 100-0% / B: 100%

R: 100% / G: 100% / B: 100% / A: 100%

Color temperature 1

Color temperature 2

Color temperature 3

Color temperature 4

Color temperature 5

Color temperature 6

Color temperature 7

Color temperature 8

Color temperature 9

Color temperature 10

Color temperature 11

000 - 010

011 - 030

031 - 050

051 - 070

071 - 090

091 - 110

111 - 130

131 - 150

151 - 170

171 - 200

201 - 205

206 - 210

211 - 215

216 - 220

221 - 225

226 - 230

231 - 235

236 - 240

241 - 245

246 - 250

251 - 255

AUTO/SOUND PROGRAMS

No Function 000 - 010

8 CHANNELS

MODE

FUNCTION DMX

Value

8 Ch

DIMMER

0~100% 000 - 255

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

AMBER

0~100% 000 - 255

WHITE

0~100% 000 - 255

PURPLE

0~100% 000 - 255

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

MODE

FUNCTION DMX

Value

12 Ch

Auto Program 1

Auto Program 2

Auto Program 3

Auto Program 4

Sound show

011 - 060

061 - 120

121 - 180

181 - 240

241 - 255

AUTO SPEED

Speed slow to fast

SOUND SENSITIVITY

Sound sensitivity OFF

Control the sound sensitivity

000 - 255

000 - 010

011 - 255

DIM MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

SMARTBATHEX

6 CHANNELS

MODE

FUNCTION DMX

Value

6 Ch

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

AMBER

0~100% 000 - 255

WHITE

0~100% 000 - 255

PURPLE

0~100% 000 - 255

SMARTBATHEX

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 FUSE REPLACEMENT

1. Disconnect this product from the power outlet.

2. Remove the safety cap by a screwdriver.

3. Replace the blown fuse with a fuse of the exact same type and

rating.

4. Install the safety cap, and reconnect power.

4.3 TROUBLESHOOTING

Fuse

Fig.12

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• All color faders set to 0

• Faulty LED

• Faulty LED board

• Check the power supply voltage

• Increase the value of the dimmer channels

• Increase the value of the color channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the xture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Faulty internal power supply

• Check for power on power outlet

• Check power cord

• Replace internal power supply

Fixture does not respond to DMX

• Wrong DMX addressing

• Damaged DMX cables

• Bouncing signals

• Check control panel and unit addressing

• Check DMX cables

• Install terminator as suggested

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

La pagina sta caricando ...

ProLights Wireless battery operated portable uplighter Manuale utente

Marca: ProLights

Modello: Wireless battery operated portable uplighter

Categoria: Stroboscopi

Tipo: Manuale utente

Questo manuale è adatto anche per

Wireless battery operated portable uplighter, 4x12W RGBWAP/FC LEDs

Scarica il pdf

rapporto

in altre lingue

English: ProLights Wireless battery operated portable uplighter User manual

ProLights Wireless battery operated portable uplighter Manuale utente

Questo manuale è adatto anche per

ProLights Wireless battery operated portable uplighter Manuale utente

in altre lingue

Documenti correlati

Altri documenti