ProLights 12x8W RGBWAP / FC high-power PAR LED Manuale utente

Marca: ProLights

Modello: 12x8W RGBWAP / FC high-power PAR LED

Categoria: Stroboscopi

Tipo: Manuale utente

USER MANUAL

MANUALE UTENTE

LUMIPAR12UH3P

EN - IT

SUPER-SLIM PARLED

LUMIPAR12UH3P

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.003-05/17

Packing content

• LUMIPAR12UH3P

• Mount bracket (2pc.)

• Power cable

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 Auto show

3. 5 Static Color

3. 6 Sound Mode

3. 7 Manual Color

3. 8 Dimmer

3. 9 Linking

3. 10 DMX conguration

3. 11 DMX addressing

3. 12 Connection of the DMX line

3. 13 Construction of the DMX termination

3. 14 DMX control

3. 15 Operation through the IRC controller

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Troubleshooting

LUMIPAR12UH3P

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with a temperature of over 45 °C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

LUMIPAR12UH3P

- 1 - INTRODUCTION

1.1 DESCRIPTION

LUMIPAR12UH3P is a super-slim PAR LED designed for professional use and as a powerful wash lightwith

the ability to perform an outstanding chromatic capacity through the new optical design and light source

based on 6 colours mixing. LUMIPAR12UH is compatible with the infrared remote controller, for intuitive

and interactive use without need any external DMX units and can be also controlled wireless through the

optional USB WIFI transceiver in combination with WIFIBOX and the SmartColor app.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 12x8W RGBWAP LEDs

• Luminous ux: 2537lm

• Lux: 963,5lux @3m

• Source life expectancy: >50.000 h

OPTICS

• Beam angle: 25°

• Field angle: 45°

• Lens diameter: 38mm

• Additional optics: 25° (inc) - 45° (op)

COLOUR SYSTEM

• Colour mixing: RGBWAP/FC

• White presets: 3200~10000K

• Colour wheel: virtual colour wheel with presets

• Macros: built-in white presets

DYNAMIC EFFECTS

• Static colour mode: selection of static colour

• Manual colour mode: manual adjustment of dimmer and strobe

• Auto mode: built-in programs with execution speed adjustment

• BODY

• Body: sturdy die-cast aluminium body conceived for long-time durability

• Body colour: black

CONTROL

• Protocols: DMX512

• DMX channels: 6/11channel

• Display: LED display user interface

• Firmware upgrade: yes, via USB-DMX interface (UPBOX1) not included

• IR: infrared sensor controlled by remote

• Master/Slave: for synchronized operation of more units linked in a chain

ELECTRONICS

• Dimmer: linear 0~100% electronic dimmer

• Strobe / shutter: 1-28 Hz, electronic

• Operating temperature: -10° ~ +45°

• Flicker: icker free operation

ELECTRICAL

• Power supply: 100-240V – 50/60Hz

• Power consumption (at 230V): 83W

• Power consumption (at 120V): 84,5W

• Output (at 230V): 30 units on a single power line

LUMIPAR12UH3P

Technical drawing

Fig.1

200

253 237

• Output (at 120V): 16 units on a single power line

PHYSICAL

• Cooling: natural cooling of the peculiar chassis and to absence of fans

• Sospension and xing: double hanging bracket suitable for safe hanging and for oor positioning

• Data: USB port for USB WIFI transmitter (optional)

• Signal connection: XLR 3p IN/OUT connectors

• Power connection: variants available

• IP rating: 44

• Dimensions (WxHxD): 253x200x237mm

• Weight: 3.3kg

LUMIPAR12UH3P

1.3 OPERATING ELEMENTS AND CONNECTIONS

Fig.2 - Rear panel

1. MOUNTING BRACKET.

2. LOCKING KNOB for the mounting bracket.

3. DMX IN (3-pole XLR):

1 = ground, 2 = DMX -, 3 = DMX +.

4. DMX OUT (3-pole XLR):

1= ground, 2 = DMX -, 3 = DMX +.

5. CONTROL PANEL with display and 4 button

used to access the control panel functions

and manage them.

6. POWER IN (PowerCON IN) mains plug for

connection to a socket (100-240V~/50/60Hz)

via the supplied mains cable.

7. MICROPHONE to control the show by the

external audio signal.

8. SAFETY EYE to attach safety cable.

9. Universal Serial Bus (USB).

10. POWER OUT (PowerCON OUT): power output

for connection of multiple units in series.

11. GND POINT grounding the xture to the earth.

63 4 5 7

11108 9

LUMIPAR12UH3P

- 2 - INSTALLATION

2.1 MOUNTING

LUMIPAR12UH3P may be set up on a solid and even surface. The unit can also be mounted upside down

to a cross arm. For xing, stable mounting clips are required. The mounting place must be of sucient

stability and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location by means of the mounting bracket (1).

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.

• Adjust the projector and use the knob (2) to slightly release or tighten the locking mechanism of the

bracket if is necessary.

Fig.3

LUMIPAR12UH3P

Fig.4 - Functions of the buttons

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the unit is ready for operation

and can be operated via a DMX controller or it independently performs its show program in succession.

To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and o via a light switch.

3.2 BASIC

Access control panel functions using the four panel buttons located directly underneath the LED Display

(g.4).

MENU UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

MENU UP DOWN ENTER

LUMIPAR12UH3P

3.3 MENU STRUCTURE

3.4 AUTO SHOW

This xture has a built-in automatic program. To access this, please see the below instructions:

• Press the button MENU so many times until shows P-- , then press the button ENTER.

• Using UP/DOWN button, select one of the programs P1 - P4.

• Press the button ENTER to conrm.

• Press the button MENU until S-- appears on the display.

• Use the button UP/DOWN to select the auto programs speed S001 - S100 (slow-fast).

• Press the button ENTER save the setting.

3.5 STATIC COLOR

This xture has the ability to accept custom static color settings. Access these chases via the control panel

on the back of the xture.

DMX Personality and

Starting Address

6 CH

d1 - d512

Selects DMX personality and DMX starting

value

11 CH

d1 - d512

2 Static Colors C--

C1 - C63 Selects 1 of 63 static colors

3 Auto Programs P--

P1 - P4 Selects 1 of 4 auto programs

4 Programs Speed S--

S1 - S100 Sets auto program speed (slow to fast)

5 Sound Active Snd

Snd1 - Snd2 Selects Sound Active mode

6 Sound Sensitivity SenS

u0 - u100 Sets sound sensitivity (low to high)

7 Custom Color Mixing U--

r0 - r255 Red (0-100%)

g0 - g255 Green (0-100%)

b0 - b255 Blue (0-100%)

A0 - A255 Amber (0-100%)

W0 - W255 White (0-100%)

P0 - P255 Purple (0-100%)

8 Dimmer dIM

OFF OFF: Dimmer speed o

dIM1 DIM1: Dimmer speed fast

dIM2 DIM2: Dimmer speed middle

dIM3 DIM3: Dimmer speed slow

9 Infrared SET

Turns infrared on or o

OFF

LUMIPAR12UH3P

• Press the button MENU so many times until shows C-- , then press the button ENTER.

• Using UP/DOWN button, select one of the programs C1 - C63.

• Press the button ENTER to conrm.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.6 SOUND MODE

In music mode, via its integrated microphone, the unit can be controlled by music with a clear rhythm in

the bass range. If the music control should not work optimally, increase the volume or reduce the distance

between the sound source and the light eect unit.

• Press the button MENU so many times until the display shows Snd.

• Using UP/DOWN button, select one of the modes Snd1 or Snd2.

• Press the button ENTER to conrm.

• You can set the microphone sensitivity pressing the button MENU so many times until the display show Sens.

• Using the button UP/DOWN, select the desired value sensitivity (slow-fast) u0 - u100.

• Press the button ENTER to conrm.

3.7 MANUAL COLOR

This mode allows to combine the colors red, green, blue, amber, white and purple (r, g, b,A, W, P).

• Press the button MENU so many times until the display shows U-- , then press the button ENTER.

• Select the color r, g, b, A, W or P through the buttons UP/DOWN.

• Press the button ENTER to conrm.

• Using UP/DOWN button, select the desired color value 000 - 255.

• Press ENTER button to continue to the next color.

• Continue until the desired mix is obtained.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.8 DIMMER

• Enter in Dimmer mode to select specic dimming curve, press the button MENU so many times until

shows dIM, and press the button ENTER to conrm.

• Press the button UP/DOWN to select OFF - dIM1 - dIM2 - dIM3.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.9 LINKING

Several units may be interconnected in order to control all further slave units to the same eect of the

master unit. Use standard DMX cables to daisy chain your units together via the DMX connector on the

rear of the units. For longer cable runs we suggest a terminator at the last xture (see page 12).

1. Connect the DMX OUT of the master unit via 3-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

3.10 DMX CONFIGURATION

LUMIPAR12UH3P is equipped with dierent DMX conguration.

• Press the button MENU to select the desired DMX conguration (6CH - 11CH), then press the button

ENTER.

LUMIPAR12UH3P

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

6 33 33-38 39 45 51

11 33 33-41 44 55 66

• Press the button UP/DOWN to select the desider value (001 - 512), then press the button ENTER to con-

rm.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

The tables on page 13 indicate the operating mode and DMX value. The LUMIPAR12UH3P is equipped

with 3-pole XLR connections.

3.11 DMX ADDRESSING

To able to operate the LUMIPAR12UH3P with a light controller, adjust the DMX start address for the rst a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX

channel, adjust the start address 33 on the LUMIPAR12UH3P.

The other functions of the light eect panel are then automatically assigned to the following addresses.

An example with the start address 33 is shown below:

DMX Address: 51DMX Address: 39DMX Address: 33 DMX Address: 45

Fig.5 - Example 6 DMX channels conguration

............

DMX512 Controller

LUMIPAR12UH3P

Fig.6

Fig.7

3.12 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.13 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 3-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Example:

3 pin XLR connector

LUMIPAR12UH3P

3.14 DMX CONTROL

6 CHANNELS

MODE

FUNCTION DMX

Value

6 Ch

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

AMBER

0~100% 000 - 255

WHITE

0~100% 000 - 255

PURPLE

0~100% 000 - 255

11 CHANNELS

MODE

FUNCTION DMX

Value

11 Ch

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

AMBER

0~100% 000 - 255

WHITE

0~100% 000 - 255

PURPLE

0~100% 000 - 255

COLOR MACRO

No Function

Color Macros

000 - 015

016 - 255

STROBE

No Function

Strobe slow to fast

000 - 015

016 - 255

PROGRAM SPEED

Speed slow to fast 000 - 255

SOUND SENSITIVITY

Sound sensistivity OFF

Control the sound sensitivity

000 - 010

011 - 255

PROGRAMS

No function

0 - 100%

100%-0

100%-0-100%

Colors Fade

6 Colors snap

63 Colors snap

Sound Control

000 - 031

032 - 063

064 - 095

096 - 127

128 - 159

160 - 191

192 - 223

224 - 255

DIMMER

0~100% 000 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode 1 (fast speed)

Dimmer speed mode 2 (middle speed)

Dimmer speed mode 3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

LUMIPAR12UH3P

3.15 OPERATION THROUGH THE IRC CONTROLLER

To control the LUMIPAR12UH3P with the infrared remote control:

• Press the button MENU repeatedly until SET, then press button ENTER to conrm.

• Using UP/DOWN button to select On or O to enable or disable the infrared remote control.

• Press the button ENTER to conrm the chose.

NOTE - Make sure to point the controller directly at the receiver on the product.

Automatic Mode

Automatic Mode will enable you to run the automatic programs on the

product.

To turn on Automatic Mode:

1. Press AUTO on the controller.

2. Press + or – to choose between the dierent auto programs.

To adjust the speed of the automatic program:

1. Press SPEED on the controller.

2. Press %.

3. Press + or – to either increase or decrease the speed of the program.

Sound Active Mode

Sound Active Mode will enable the product to respond to the music.

To turn on Sound Active mode:

1. Press SOUND on the controller.

To adjust sound sensitivity in Sound Active mode:

1. Press SENSITIVITY on the controller.

2. Press %.

3. Press + or – to either increase or decrease sound sensitivity.

Manual Color Control

To choose a specic color with the controller:

1. Press MANUAL on the controller.

2. Press any number between 0-9 to choose your color.

To manually control the RGBAWP percentage:

3. Press MANUAL on the controller.

4. Press R, G, B, A, W or P to choose your color.

5. Press + or – to increase or decrease the percentage of each color.

Miscellaneous Operation

To adjust the strobe rate of the program:

1. Press STROBE on the controller.

2. Press + or – to increase or decrease the strobe rate.

3. Press STROBE again to turn o the strobe.

To change the switching eect of the program:

• Press FADE/SNAP on the controller.

• Fade will slowly switch the eect. Snap will rapidly switch the eect.

To black out the lights:

• Press BLACK OUT on the controller.

• This will turn o all the lights until the button is pressed again.

NOTE - The controller will not respond to any inputs when Black Out is activated. If the remote does not

respond when a button is pressed, try pressing BLACK OUT. You may have inadvertently activated BLACK

OUT.

Fig.8

IRC REMOTE

BLACK

OUT

AUTO

STROBE SPEED

SOUND

SENSI-

TIVITY

MANUAL

FADE

G B

7 8 9

UV W

LUMIPAR12UH3P

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 FUSE REPLACEMENT

1. Disconnect this product from the power outlet.

2. Remove the safety cap by a screwdriver.

3. Replace the blown fuse with a fuse of the exact same type and

rating.

4. Install the safety cap, and reconnect power.

4.3 TROUBLESHOOTING

Fuse

Fig.9

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• All color faders set to 0

• Faulty LED

• Faulty LED board

• Check the power supply voltage

• Increase the value of the dimmer channels

• Increase the value of the color channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the xture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Faulty internal power supply

• Check for power on power outlet

• Check power cord

• Replace internal power supply

Fixture does not respond to DMX

• Wrong DMX addressing

• Damaged DMX cables

• Bouncing signals

• Check control panel and unit addressing

• Check DMX cables

• Install terminator as suggested

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

REV.003-05/17

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al ne di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modicare, in

qualunque momento e senza preavviso, le speciche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

• LUMIPAR12UH3P

• Staa di ssaggio (2pz.)

• Cavo di alimentazione

• Manuale utente

Contenuto dell'imballo:

INDICE

Sicurezza

Avvertenze generali

Attenzioni e precauzioni per l’installazione

1 Introduzione

1. 1 Descrizione

1. 2 Speciche tecniche

1. 2 Elementi di comando e di collegamento

2 Installazione

2. 1 Montaggio

3 Funzioni e impostazioni

3. 1 Funzionamento

3. 2 Impostazione base

3. 3 Struttura menu

3. 4 Autoshow

3. 5 Static Color

3. 6 Modalità Musicale

3. 7 Manual Color

3. 8 Funzione dimmer

3. 9 Collegamento

3. 10 Congurazione canali DMX

3. 11 Indirizzamento DMX

3. 12 Collegamenti della linea DMX

3. 13 Costruzione del terminatore DMX

3. 14 Canali DMX

3. 15 Funzionamento tramite il controller IRC

4 Manutenzione

4. 1 Manutenzione e pulizia del sistema ottico

4. 2 Sostituzione fusibile

4. 3 Risoluzione dei problemi

LUMIPAR12UH3P

ATTENZIONE! Prima di effettuare qualsiasi operazione con l’unità, leggere con attenzione

questo manuale e conservarlo accuratamente per riferimenti futuri. Contiene informazioni

importanti riguardo l’installazione, l’uso e la manutenzione dell’unità.

SICUREZZA

Avvertenze generali

• I prodotti a cui questo manuale si riferisce sono conformi alle Direttive della Comunità Europea e per-

tanto recano la sigla .

• Il dispositivo funziona con pericolosa tensione di rete 230V~. Non intervenire mai al suo interno al di

fuori delle operazioni descritte nel presente manuale; esiste il pericolo di una scarica elettrica.

• È obbligatorio eettuare il collegamento ad un impianto di alimentazione dotato di un’eciente messa

a terra (apparecchio di Classe I secondo norma EN 60598-1). Si raccomanda, inoltre, di proteggere le

linee di alimentazione delle unità dai contatti indiretti e/o cortocircuiti verso massa tramite l’uso di

interruttori dierenziali opportunamente dimensionati.

• Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere eettuate

da un installatore elettrico qualicato. Vericare che frequenza e tensione della rete corrispondono alla

frequenza ed alla tensione per cui l’unità è predisposta, indicate sulla targhetta dei dati elettrici.

• L’unità non per uso domestico, solo per uso professionale.

• Evitare di utilizzare l’unità:

- in luoghi soggetti a vibrazioni, o a possibili urti;

- in luoghi a temperatura superiore ai 45°C.

• Evitare che nell’unità penetrino liquidi inammabili, acqua o oggetti metallici.

• Non smontare e non apportare modiche all’unità.

• Tutti gli interventi devono essere sempre e solo eettuati da personale tecnico qualicato. Rivolgersi al

più vicino centro di assistenza tecnica autorizzato.

• Se si desidera eliminare il dispositivo denitivamente, consegnarlo

per lo smaltimento ad un’istituzione locale per il riciclaggio.

Attenzioni e precauzioni per l’installazione

• Se il dispositivo dovesse trovarsi ad operare in condizioni dierenti da quelle descritte nel presente

manuale, potrebbero vericarsi dei danni; in tal caso la garanzia verrebbe a decadere. Inoltre, ogni altra

operazione potrebbe provocare cortocircuiti, incendi, scosse elettriche, rotture etc.

• Prima di iniziare qualsiasi operazione di manutenzione o pulizia sull’unità togliere la tensione dalla rete

di alimentazione.

• È assolutamente necessario proteggere l’unità per mezzo di una fune di sicurezza. Nell’eseguire qual-

siasi intervento attenersi scrupolosamente a tutte le normative (in materia di sicurezza) vigenti nel

paese di utilizzo.

• Installare l’unità in un luogo ben ventilato.

• Mantenere i materiali inammabili ad una distanza di sicurezza dall’unità.

• I ltri, le lenti o gli schermi ultravioletti se danneggiati possono limitare la loro ecienza.

• I LED devono essere sostituiti se danneggiati o termicamente deformati.

• Non guardare direttamente il fascio luminoso. Tenete presente che i veloci cambi di luce possono pro-

vocare attacchi d’epilessia presso persone fotosensibili o epilettiche.

• Non toccare l’alloggiamento del prodotto quando è in funzione perché potrebbe essere molto caldo.

La pagina sta caricando ...

ProLights 12x8W RGBWAP / FC high-power PAR LED Manuale utente

Marca: ProLights

Modello: 12x8W RGBWAP / FC high-power PAR LED

Categoria: Stroboscopi

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: ProLights 12x8W RGBWAP / FC high-power PAR LED User manual

ProLights 12x8W RGBWAP / FC high-power PAR LED Manuale utente

ProLights 12x8W RGBWAP / FC high-power PAR LED Manuale utente

in altre lingue

Documenti correlati

Altri documenti