Moog DeputyDome SERIES Istruzioni per l'uso

Marca: Moog

Modello: DeputyDome SERIES

Categoria: Accessori per telecamere di sicurezza

Tipo: Istruzioni per l'uso

Questo manuale è adatto anche per

- 1 -

www.videolarm.com

Installation and Operation Instructions for the following models:

DDW10CN2 DeputyDome™, Bullet-Resistant IP Camera System, PTZ and 26x Day/

Night Camera System features Heavy-Duty Metal Gear Pan/ Tilt. MPEG-4

and MJPEG video compression format, full D1. Clear dome, with 24Vac

input, heater/ blower Tough enough to stop a 9mm bullet

PDDW10CN2 (Pressurized Version)

DeputyDome™, Bullet-Resistant IP Camera System, PTZ and 26x Day/

Night Camera System features Heavy-Duty Metal Gear Pan/ Tilt. MPEG-4

and MJPEG video compression format, full D1. Clear dome, with 24Vac

input, heater/blower Tough enough to stop a 9mm bullet

Be fo re a tt em pt in g to c on ne ct o r op er at e th is p ro du ct ,p le as e re ad t he se i ns tr uc ti on s co mp le te ly.

81-IN5387

12-13-2011

D e p u t y D o m e ™

Bullet-Resistant IP Camera Housing

- 2 -

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. The installation should be made by a qualied installer.

b. The installation should be in compliance with local codes.

c. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including ampliers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specied by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the integrity

of the installation is intact. Failure to comply with the foregoing could result in the unit separating

from the support structure and falling, with resultant damages or injury to anyone or anything struck

by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make future

shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us at

the following number:

The lightning ash with an arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of non-insulated

“dangerous voltage” within the product’s

enclosure that may be of sufcient magnitude

to constitute a risk to persons.

Este símbolo se piensa para alertar al usuario a la presencia

del “voltaje peligroso no-aisIado” dentro del recinto de los

productos que puede ser un riesgo de choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la presence

“de la tension dangereuse” non-isolée dans la clôture de

produits qui peut être un risque de choc électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença “di

tensão perigosa non-isolada” dentro do cerco dos produtos

que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla presenza

“di tensione pericolosa” non-isolata all’interno della

recinzione dei prodotti che può essere un rischio di scossa

elettrica

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones importantes

en la literatura que acompaña la aplicación.

Ce symbole de point d’exclamation est prévu pour alerter

l’utilisateur à la presence des instructions importantes dans

la littérature accompagnant l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der Literatur

alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido alertar o

usuário à presença de instruções importantes na literatura

que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti nella

letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800 - 554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING

TO QUALIFIED SERVICE PERSONNEL.

- 3 -

Limited Warranty for Moog Videolarm Products

Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:

PRODUCT CATEGORY PARTS \ LABOR

All Enclosures and Electronics* Five (5) Years

Poles/PolEvators™/CamEvator Three (3) Years

Warrior Series™/Q-View™/IR Illuminators Five (5) Years

SView Series™ Five (5) Years **6 months if used in auto scan/tour operation

Controllers Five (5) Years

Power Supplies Five (5) Years

EcoKit Three (3) Years

Accessory Brackets Five (5) Years

Liberty Dome Three (3) Years

*DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™ Three (3) Years **6 months if used in auto scan/tour operation

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Moog Videolarm

Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with

a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support

Team at 800.554.1124, extension 101. Moog Videolarm will return the repaired Product freight prepaid to Purchaser. Moog Videolarm is not obligated to

provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or

parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions.

TERMS AND CONDITIONS

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an

explanation of the claim shall be given promptly by Purchaser to Moog Videolarm. All claims for warranty service must be made within the warranty period.

If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of

investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period

of the entire Product. The speci c warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that

part or the remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any

Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the

warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes,

earthquakes), modi cation, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance

procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the

Product. Furthermore, Moog Videolarm shall have no liability where a schedule is speci ed for regular replacement or maintenance or cleaning of certain parts

(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-quali ed personnel; operation of the Product outside of the

published environmental and electrical parameters, or if such Product’s original identi cation (trademark, serial number) markings have been defaced, altered,

or removed. Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not

been sold by Moog Videolarm to the Purchaser. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS”

(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. Any

cost associated with removal of defective product and installation of replacement product is not included in this warranty.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR

ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL

CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT

THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS

PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF Moog Videolarm, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND

WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL

PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER

FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,

REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

- 4 -

WALL MOUNT INSTALLATION:

1. Remove the (2) tamper resistant screws on the top of the housing with the security

tool provided in the installation packet

(Figure 1, next column).

STANDARD INSTALLATION PROCEDURE

ELECTRICAL SPECIFICATIONS (Camera with hardwire pan/tilt)

Power Source & Power Consumption

(includes: heater, blower and camera)

P/DDW10CR/02 - 115 VAC, 90 vA, 0.8 Amps

P/DDW10CR2/02 - 24 VAC (Class 2), 90 vA, 3.75 Amps

P/DDW10CR3/02 - 220 VAC, 90 vA, 0.45 Amps

CAMERA SPECIFICATIONS

Resolution - 470TVL - NTSC, 460TVL - PAL

Minimum Illumination - 0.2 Lux B&W mode, 3.0 Lux color mode

Zoom Ratio - 18X, 4.1 - 73.8mm optical, 216x digital

Format - 1/4"

White Balance - Auto

Electronic Shutter - 20 step

NOTE:

The DeputyDome™ is packed in two separate boxes, one for the housing and one for the

pan/tilt and bullet-resistant liner. Installation should be completed as follows:

1. Run wiring to the chosen location.

2. Detach the housing and mount the wall bracket.

3. Make wiring connections.

4. Complete wiring runs.

5. Install the pan/tilt and make necessary adjustments.

6. Install the bullet-resistant liner.

7. Attach the housing and ome.

These instructions include procedures for installing both the standard and

pressurized versions.

Figure 1

Figure 3

Figure 2

WIRING (See wiring charts, next page)

FOR NON-PRESSURIZED VERSION

5. Run all electrical wiring through the bracket and out the access hole.

6. Attach appropriate connectors to incoming wiring (Figures 5 and 6). The housing has

two inputs for power - one for heaters, and one for camera and blower. See the general

specications for current draw at the appropriate voltage.

FOR PRESSURIZED VERSION

5A. Connect incoming power and video wires to the connector supplied. (Figures 7 and

8 for pin out on connector.)

NOTE: It is helpful to attach short leads (2.00") to the video pins and solder these to

the video shield on the coax cable. Use an insertion tool to assist with the assembly of

the connector.

6A. Connect the 18-pin connector to the housing.

7. With the mounting bracket securely mounted and all wiring connections completed,

the next step is adjusting the pan/tilt.

Tamper

resistant

screws

Flange nuts

Tamper

resistant

screws

Access plate

2. Loosen the (4) ange nuts, and turn the housing clockwise to remove the housing

from the wall mount (Figure 2).

4. After the wall mount is securely attached to the wall, remove the (3) 10-32 tamper

resistant screws with the provided security tool (Figure 3) and take off the access plate.

3. The wall mount can now be attached to the wall with appropriate fastening hardware.

WALL MOUNT INSTALLATION (cont.)

- 5 -

E F

U T

Alarm Common

Alarm In 3

Alarm In 2

Alarm In 1

RXB

TXB

TXA

Heater /Blower

Camera Power

Shield

Video

RXA

INSTALLING THE PAN/TILT

1. Slide the pan/tilt back into place. All of the electrical connections are made by the

edge connector and will be engaged at that point.

2. Place the pan/tilt inside the housing so that the alignment pins are facing the housing

PC board. The two vertical anges on the pan/tilt quick release plate should slide in

between the two vertical anges on the housing plate. There are also notches on the back

side of the quick release plate that align with support tabs on the housing plate (Figure 8).

Figure 8

3. With the two vertical anges lined up and the quick release notches inserted through

the support tabs, slide the pan/tilt side ways, towards the housing PC board. There are

two alignment pins on the front of the quick release plate that will engage with holes on

the housing bracket. The pan/tilt should be pushed side-ways until the panel fastener

aligns with the mating insert in the housing plate. Be gentle with the pan/tilt because

the wiring connections are being made as the pan/tilt is being slid sideways (Figure 9).

Front View Side View

Edge

Connector

Figure 10

Panel

Fastener

4. Tighten the panel fastener with a long Phillips screwdriver (Figure 10).

Figure 9

5. Reattach the bullet-resistant liner. Make sure that the viewing slot is in front of the

ballistic window. Each liner arm has an alignment pin that mates with a hole on the

ballistic. When both pins are aligned with their appropriate alignment hole, the (4) Phillips

head captive screws will align with inserts on the liner arms. Tighten the (4) screws to

secure the liner.

E F

U T

Alarm Common

Alarm In 3

Alarm In 2

Alarm In 1

White/Green

Heater /Blower

Camera Power

Orange

White/Orange

Green

GND

Wiring Chart Non-Pressurized Receiver Version

A. Heater

1) Red - Heater 1

2) N/C

3) Red - Heater

B. Camera Power

1) Black - V2

2) Orange - V1

C. RJ45

Wiring Pressurized Receiver Version

The following chart is provided as a general guide for the input power for heater,blower

and camera, between the housing and power supply.

Figure 7

Figure 5

Wire Gauge

VA 22 20 18 16 14 12

70 25ft 40 ft 64 ft 100 ft 162 ft 260 ft

7 m 14 m 20 m 30 m 50 m 80 m

CAUTION: Using smaller than recommended cable sizes can result in poor performance

and damage to the heater and camera.

Figure 7A

Wiring Pressurized Network Version

- 6 -

REATTACHING THE DOME ON PRESSURIZED UNITS

1. The dome on the pressurized unit must be attached correctly for the unit to function

properly. All screws and posts must line up exactly.

2. There are two posts on the underside of the dome which must be placed in the proper

slots on the housing (See Figure 13). One is located on the lanyard side of the dome and

the other is on the opposite side. The dome is oriented properly when the lanyard can

be attached to the housing.

Lanyard

Post (one on

either side)

Figure 13

Posts MUST t

in these slots

(one on either

side)

Close Up View of Dome

Lanyard screw hole

on housing

INSTALLING THE HOUSING ON THE BRACKET

1. Make sure that the (4) ange nuts on top of the DeputyDome™ are loosened

and that the tamper-resistant screws are not attached. Lift the unit up to the wall

mount and align the ange nuts with the keyhole slots on the mount (Figure 11). Turn

counterclockwise so that the nuts are inside the slots. Make sure that the holes for the

tamper-resistant screws line up. Tighten the ange nuts.

IMPORTANT NOTE: For non-pressurized units make sure the wiring on top of the housing

is fed through the opening on the bottom of the wall mount. On pressurized units the

connector will t directly into the opening.

Figure 11

Figure 12

1/4 - 20 Security Screws

3. Make all wiring connections.

NOTE: On non-pressurized versions be sure to cover the BNC connectors with electrical

tape to help prevent a short between the wall mount bracket and the video wiring.

4. Double check all wiring and push it back through the access opening into the wall mount

bracket. FOR PRESSURIZED HOUSINGS: At this point, pressurize the housing following the

instructions on page 7.

5. Reattach the access cover.

6. Test the function of all the equipment.

7. Reattach the lower dome with the tamper-resistant screws and security tool used earlier.

FOR PRESSURIZED HOUSINGS: See the important instructions on the next page for

reattaching the dome.

2. Reattach and tighten the (2) security screws (Figure 12).

6. The liner should still be able to move up by about 1/16" on an inch to allow the liner

to move when shot and transfer the force to the housing instead of the pan/tilt.

Flange nuts

- 7 -

IP Instructions

The factory default IP adress is 192.168.0.200.

See IP Ready camera instruction for installation details.

For Pan/Tilt control click on PTZ control icon in top right corner.

Pan/Tilt control contains standard pan/tilt/camera control functions.

To save preset, pull down #1 preset, move camera to desired position and then hit

"save" to save preset.

You can store up to 18 presets. Adjusting "speed" setting will correspondingly adjust

dwell time when the preset is saved. Use low numbers for longer dwell.

To modify camera setting, select preset "95." Set speed control to "9," then use up/

down and left/right to access sub-camera menu.

Scroll to Exit

*Tour button will allow you to tour sequentially through presets.

Select

PreSets

Lens

Functions

Pan/Tilt

functions (also

used to scroll

camera menu)

Use to save

or remove

PreSets

- 8 -

Filling and Relling

1. Attach the barb to the regulator.

2. Remove the cap from the Schraeder valve.

3. Set the gauge on the regulator to between 5 and 8 psi.

4. Place the air chuck on the Schraeder valve, just as you would on a tire, and press

down to begin lling. Continue until the regulator stops feeding nitrogen into the

housing and begins to let off excess pressure. In addition, as dry nitrogen is inserted

into the housing the humidity strip will change from pink to blue.

CAUTION: Do not attempt to ll beyond this point.

NOTE: The humidity sensitive tape will appear blue under normal dry conditions. The

tape will turn pink if exposed to moisture or humidity

5. Replace the metal cap on the Schraeder valve. The cap must be installed on the

Schraeder valve (air input valve) to ensure an airtight enclosure.

6. Check the pressure in the unit with a pressure gauge. It should be 5psi.

7. Reattach wall mount access cover plate.

PROCEDURES FOR PRESSURIZED HOUSINGS

Pressurized housings provide maximum protection for CCTV cameras and lenses. The

charge of dry nitrogen inside the housing eliminates the effects of moisture, dust,

insects and corrosive exhaust fumes. This allows a longer lifetime for your surveillance

equipment.

To ll (or rell) a pressurized housing, you must have the following:

1. A tank of dry nitrogen (or oxygen)

2. A regulator on the tank

3. A hose with air chuck to connect the regulator to the housing’s intake valve

Dry Nitrogen

Nitrogen is a readily available. To obtain supplies, check your local yellow pages for a

medical or industrial gas provider. If the tank is to be carried from location to location,

a size of 40 cubic foot is recommended. This should be enough to rell 30 individual

housings. Handle the tanks with care. Although nitrogen is an inert gas, the tank is

highly pressurized and if the valve or regulator is damaged the tank could be danger-

ous. Tanks of dry nitrogen can be kept for several years.

The Regulator

The tank will have a standard 580 tting, but a regulator will be required. A

recommended regulator for the tank would be a Harris #9296-15-580 or

#425-15-580. For local distribution you can contact Harris at 800-241-0804.

The Hose

The purge valve, called a “Schraeder” or “dill” valve, is similar to the air intake valve on

car or bicycle tires. To connect the regulator to the purge valve on the housing, you’ll

need a hose with a 1/4” barb on one end and an air chuck on the other. The barb

connects to the regulator, the air chuck to the Scraeder valve. These hoses can be

obtained at local auto parts stores.

PRECAUTIONS:

1. Always use safety goggles when servicing the unit.

2. Inspect the enclosure upon opening the product and be sure the unit has not been

damaged during shipping. Domes that have been cracked or show any signs of

damage should be replaced immediately.

3. Pressurize the unit with air or dry nitrogen only.

4. Do not ll the housing to more than 5 psi maximum pressure. Exceeding 5 psi will

damage the enclosure.

5. Never use an unregulated air supply to pressurize the enclosure. The valve should

be regulated to allow a maximum air pressure of 10 psi.

6. Be sure you periodically examine the unit and the attached supporting structure.

If the dome shows any signs of wear, such as stress cracking, it should be replaced

immediately.

NOTE: If you have removed the dome it must be reattached and oriented properly.

See page 5 for complete instructions.

- 9 -

Exploded View for Replacement Parts

- 10 -

Exploded View for Replacement Parts

(Pan/Tilt Assembly)

- 11 -

Exploded View for Replacement Parts

(Pan Bearing Assembly)

- 12 -

Exploded View for Replacement Parts

(Network Assembly)

- 13 -

Part No. Description

1 91-NTFL01 3/8-16 Flange Nut (4)

2 90-BTSEC06 1/4-20 x 1/2" Security screw SS (2)

3 50-VL1428 DDWC10 housing body

4 30-VL1405 DDWC10 accs mounting bracket

5 92-WSFL01 1/4 Flat Washer SS (4)

6 92-WSSL01 1/4 Split Lockwasher SS (4)

7 90-BTHH32 1/4-20 x 1/2" Hex head bolt SS (4)

8 90-BTRP31 8-32 x 3/8" Grounding screw

9 71-BLEH24 Blower, 24VDC 60MM

10 70-WPTRAN/P2 240/120V: 1.5A 24V Transformer

92-WSTH02

#8 Star washer (8)

91-NTHH06

8-32 Hex nut SS (4)

76-DD01PCB

DDWC10 Housing PCB

RP-30VL2678

Network Bracket

90-BTRP20

#10-32 x 3/8" pan head screw SS (4)

92-WSTH04

#10 Star washer (3)

19 DDWC10 Heater (2)

96-RSORNG

1/4 O-ring (3)

21 RCDWW10 Clear dome for DeputyDome™

22 90-BTSEC04 1/4-20 x 3/8" security screws (3)

25 90-BTHH33 5/16-18 x 3/4 Hex head bolt SS (3)

26 92-WSSL02 5/16 Split Lockwasher SS (3)

27 30-VL1408 DDWC10 P/T Quick release bkt

28 96-MPDDW Pan/tilt mounting pad

29 DDWC10 pan/tilt

30 30-VL1313 DDWC10 rotating liner

31 95-FSC04 10-32X1/2" Captive screw (4)

35 DDWC10 bearing assembly

36 60-4011 18 tooth 1/5" belt drive pulley

37 60-4015 55 tooth 1/5" timinig belt, pan

38 60-4013 36 tooth 1/5" belt drive pulley, DD pan

39 90-BTHH37 8-32 x 1/2" Trimmed hex head SS (8)

40 92-WSTH02 #8 Star washer (5)

81 RP70P1401S Network Card and Bracket

82 RP-70TRANS03 Power Converter

Replacement Parts List

- 14 -

Product Registration/Warranty

Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest

quality products available and superior customer service.

Should a problem arise, rest assure that Moog Videolarm stands behind its products by offering impressive warranty plans: 3 Years on all Housings, Poles,

Power Supplies, and Accessories and 5 Years on camera systems (SView, QView, Warriors), and InfraRed Illuminators.

Take a few moments and validate your purchase via the Online Product Registration Form at

www.videolarm.com/productregistration.jsp

• Simple and Trouble-Free RMA process

• Added into customer database to receive product updates / news

• Eliminate the need to archive original purchase documents:

Receipts, Purchase Orders, etc…