Moog Videolarm VLC485 Installation And Operation Instructions Manual

Marca: Moog Videolarm

Modello: VLC485

Categoria: Accessori per fotocamere

Tipo: Installation And Operation Instructions Manual

Questo manuale è adatto anche per

VLC485E

www.videolarm.com

Controller

Installation and Operation Instructions for the following models:

VLC485 RS485 controller (2) RS232 ports (1) RS485 port, joystick control. Desk top

model, 24Vac input power

VLC485E 230Vac PAL version

Before attempting to connect or operate this product, please read these instructions completely.

81-IN5240

01-11-2012

V L C 4 8 5 a n d V L C 4 8 5 E

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. The installation should be made by a qualied installer.

b. The installation should be in compliance with local codes.

c. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including ampliers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specied by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the integrity

of the installation is intact. Failure to comply with the foregoing could result in the unit separating

from the support structure and falling, with resultant damages or injury to anyone or anything struck

by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make future

shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us at

the following number:

The lightning ash with an arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of non-insulated

“dangerous voltage” within the product’s

enclosure that may be of sufcient magnitude

to constitute a risk to persons.

Este símbolo se piensa para alertar al usuario a la presencia

del “voltaje peligroso no-aisIado” dentro del recinto de los

productos que puede ser un riesgo de choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la presence

“de la tension dangereuse” non-isolée dans la clôture de

produits qui peut être un risque de choc électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença “di

tensão perigosa non-isolada” dentro do cerco dos produtos

que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla presenza

“di tensione pericolosa” non-isolata all’interno della

recinzione dei prodotti che può essere un rischio di scossa

elettrica

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones importantes

en la literatura que acompaña la aplicación.

Ce symbole de point d’exclamation est prévu pour alerter

l’utilisateur à la presence des instructions importantes dans

la littérature accompagnant l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der Literatur

alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido alertar o

usuário à presença de instruções importantes na literatura

que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti nella

letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800 - 554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING

TO QUALIFIED SERVICE PERSONNEL.

Limited Warranty for Moog Videolarm Products

Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:

PRODUCT CATEGORY PARTS \ LABOR

All Enclosures and Electronics* Five (5) Years

Poles/PolEvators™/CamEvator Three (3) Years

Warrior Series™/Q-View™/IR Illuminators Five (5) Years

SView Series™ Five (5) Years **6 months if used in auto scan/tour operation

Controllers Five (5) Years

Power Supplies Five (5) Years

EcoKit Three (3) Years

Accessory Brackets Five (5) Years

Liberty Dome Three (3) Years

*DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™ Three (3) Years **6 months if used in auto scan/tour operation

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Moog Videolarm

Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with

a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support

Team at 800.554.1124, extension 101. Moog Videolarm will return the repaired Product freight prepaid to Purchaser. Moog Videolarm is not obligated to

provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or

parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions.

TERMS AND CONDITIONS

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an

explanation of the claim shall be given promptly by Purchaser to Moog Videolarm. All claims for warranty service must be made within the warranty period.

If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of

investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period

of the entire Product. The speci c warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that

part or the remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any

Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the

warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes,

earthquakes), modi cation, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance

procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the

Product. Furthermore, Moog Videolarm shall have no liability where a schedule is speci ed for regular replacement or maintenance or cleaning of certain parts

(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-quali ed personnel; operation of the Product outside of the

published environmental and electrical parameters, or if such Product’s original identi cation (trademark, serial number) markings have been defaced, altered,

or removed. Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not

been sold by Moog Videolarm to the Purchaser. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS”

(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. Any

cost associated with removal of defective product and installation of replacement product is not included in this warranty.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR

ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL

CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT

THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS

PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF Moog Videolarm, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND

WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL

PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER

FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,

REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

Page No.

1.0 Table of Contents 1

1.1 General Description 1

1.2 Specication 1

1.3 Included Accessories 2

1.4 Location and Description of Controls 2

1.5 Location of Connectors 2

1.6 Connections 3

2.0 Control of Basic Functions 3

2.1 Camera Selection Pan/Tilt Movement 3

2.2 Camera Zoom/ Focus/Iris Functions 3

2.3 Pan/Tilt Movement 3

2.4 Presets 3

2.5 Autotour 4

2.6 Sequencing 4

2.7 Alarms 4

3.0 Menu Items 4

3.1 Dome Selection Type 4

3.2 Multiplexer Type 4

3.3 Preset Lockout 4

3.4 Autotour Dwell 5

3.5 Beep Enable 5

3.6 Sequence 5

3.7 Sequence Dwell 6

3.8 Alarms 6

3.9 Pass Code 6

4.0 PC Port 6

4.1 PC Port Commands 6

4.2 General Command Message Format 6

4.3 Motion Command Messages 6

4.4 Preset and Dome Parameter Messages 7

4.5 Controller Parameter Messages 7

4.6 Custom Controller LCD Messages 7

5.0 Master Unit Function 8

A NOTE BEFORE BEGINNING

Each camera controlled by the VLC485 must have a unique address. The default

address for most cameras is "1". See the instructions for your camera for steps to

change the address.

1.0 TABLE OF CONTENTS

1.1 GENERAL DESCRIPTION

The VLC485 is a pan/tilt controller that ties together the major elements of an

integrated system and provides a single human interface for the system. As such, the

VLC485 can control pan/tilt units, interface to multiplexers, and communicate with a

personal computer for computer-controlled operation.

The LCD is used to display current status as well as to provide a menu system for

setting operational parameters.

The VLC485 is designed for desktop operation; all connectors are located in the rear

of the unit so that all cables can be routed from the back of the unit.

1.2 SPECIFICATIONS

Power Source

Data Connections

Pan/Tilt Control

Camera Control

Multiplexer Control

Alarms

Conguration

Display

External Serial

Communications Port

Operating Environment

4-pin compression connetor: RS485/422

Pan/Tilt control network.

9-pin d-sub connector: RS232 multiplexer

port.

9-pin d-sub connector: RS232 external serial

communications port.

5v DC 250 ma.

Maximum number of pan/tilts: 99.

Protocols: Videolarm, Sensormatic, Pelco,

and Kalatel.

Manual control: pan, tilt via joystick.

Speed: Variable.

Presets: go to, set, clear.

Autotour (Videolarm protocol): on, off, set

dwell, set speed.

Manual control: Zoom, focus, iris.

Auto: focus, iris (where supported by

camera).

Protocols: TBD.

Number of channels: up to 32.

Eight external alarm inputs and one relay

contact alarm output.

Menu driven, access controlled by

optional passcode.

LCD, 20 character x 2 lines.

9600 baud, 8 bits, 1 start, 1stop, no

parity

Protocols: Videolarm.

Temperature: 0˚ C – 50˚ C.

Humidity: 90% maximum

(non-condensing).

Altitude: 10,000 ft. maximum.

1.4 LOCATION AND DESCRIPTION OF CONTROLS

1.3 INCLUDED ACCESSORIES

(1) Control Output Connector

(1) Alarm Output Connector

(1) 5 VDC AC Adapter

1.5 LOCATION OF INPUT/OUTPUT CONNECTORS

7 8

1, 2, 3...

Alarm

Camera

Monitor

(for future use)

Presets

Sequence

Auxiliary

(for future use)

Function

(for future use)

Auto Tour

Zoom Out / Zoom In

Focus Far / Focus Near

Iris Close / Iris Open

5VDC

R R

A B A B

C 8 7 6 5 4 3 2 1

N N

O C

OUT IN

Power Input

RS-485 Control

Alarm Inputs

Alarm Outputs

PC Port

MUX Port

T T

1.6 CONNECTIONS

There are ve connectors on the VLC485 Controller. These connectors are a 9-pin

connector for RS232 connections to a PC, a 9-pin connector for RS232 connections to

an external device, a 4-pin compression connector for the RS485/422 pan/tilt network,

and a 9-pin terminal for alarm inputs. The RS232 ports are congured as data com-

munication equipment (DCE) ports.

1. Multiplexer Connector: (Not Supplied)

2. PC Connector: (Not Supplied)

Pin DCE Function

2 Transmit (to PC)

3 Receive (from PC)

5 Signal Ground

3. Multiplexer Connector: (Included)

Pin Function

1 Alarm 1 input

2 Alarm 2 input

3 Alarm 3 input

4 Alarm 4 input

5 Alarm 5 input

6 Alarm 6 input

7 Alarm 7 input

8 Alarm 8 input

9 Alarm Common

10 Alarm Output NO Contact

11 Alarm Output NO Contact

12 Alarm Output Common

4. Pan/Tilt Network Connector: (Included)

Pin Function

1 TXA to pan/tilts

2 TXB to pan/tilts

3 RXA from pan/tilts

4 RXB from pan/tilts

2.0 CONTROL OF THE BASIC FUNCTIONS

2.1 CAMERA SELECTION

In order to view or control a camera and the pan/tilt, the camera must be selected. To

do this, enter the camera number using the keypad and press the CAMERA button.

The LCD should show the following:

2.2 PAN/TILT MOVEMENT

Pan/tilt movement is controlled by the joystick. If the selected pan/tilt supports variable

speed operation the speed of the pan/tilt will be increased as the joystick is moved

away from the center position.

2.3 CAMERA ZOOM/FOCUS/IRIS FUNCTIONS

CAM 01

Use the ZOOM OUT/ZOOM IN key to operate the zoom

function of a selected camera.

NOTE: Whenever the camera zoom is changed, the

controller places the camera into auto focus and auto iris

mode if these modes are available.

If you want to focus a camera manually press the FOCUS

FAR/FOCUS NEAR keys.

The IRIS CLOSED/IRIS OPEN keys will allow you to

change the iris setting of a camera.

NOTE: Some cameras provide continuous iris function as

the keys are held down; others may require repetitive key

presses.

2.4 PRESETS

For pan/tilts that support presets, up to 99 can be programmed on the VLC485. To

LOCKOUT presets, see Menu Section, Item 3.3.

TO SET A PRESET:

CAM 01

PRESET 07

Select a camera and position it to the

desired location.

Enter the preset number (1 - 99) on the

keyboard.

Press the POUND (#) key, then press

the PRESETS key.

TO GO TO A PRESET: Select the camera as noted above. Enter the preset number.

Press the PRESET button and the camera will go to the preset location. The LCD will

show the camera number and preset number as shown above.

TO CLEAR A SINGLE PRESET: Select the camera as noted above. Enter the preset

number, press the STAR (*) key, then press the PRESET button.

For errors or to change the preset number repeat the procedure.

5. Power 5VDC: (Included)

1 Center Contact + (Plus)

2 Outside Contact - (Minus)

Pin DCE Function

2 Transmit data (to main multiplexer)

3 Receive data (from main multiplexer)

5 Signal Ground

8 Signal Ground

9 Transmit data (to expansion multiplexer)

TO CLEAR ALL PRESETS: Select the camera as noted above. Press the STAR (*) key,

then press the PRESET button. A "?" will appear. Press PRESET again and all presets

for that camera will be cleared. To cancel this function, press the STAR (*) key.

2.5 AUTO TOUR

The VLC485 can accommodate pan/tilts that support Auto tour functions. To start a

pan/tilt on an Autotour, press the AUTO TOUR button. (For Pelco Protocols enter the

pattern before pressing Auto Tour)

CAM 01

AUTO

2.6 SEQUENCING

In conjunction with a multiplexer the VLC485 will sequence through a predetermined

list of up to 16 cameras. To start sequencing press the SEQUENCE button. The camera

number will show the currently active camera in the sequence and a camera select

command for the camera will be sent to the multiplexer.

To stop the Auto tour move the joystick. To SET AUTO TOUR DWELL, see Menu Section,

Item 3.4.

1, 2, 3...

CAM 01

SEQUENCING

To stop the sequence, press the SEQUENCE button or move the joystick. For

SEQUENCING OPTIONS, see Menu Section, Item 3.6.

3.0 CONTROL OF THE MENU ITEMS

3.1 CAMERA SELECTION

Additional functions are available through the menu on the VLC485. To access the

menu, press the MENU button.

To scroll through the various menu items press the STAR (#) key on the key pad. When

you're nished with your selections and want to leave menu mode, simply press the

MENU button again.

Access to the menu can be protected with a 4-digit password. See 3.9 PASSCODE to

enable the password function.

Here are the selectable settings in the menu mode:

1) Dome Type Selection

2) Multiplexer Selection

3) Preset Enable

4) Autotour Dwell (Available for Videolarm and Kalatel)

5) Set Beep

6) Sequence of Camera (when used with a multiplexer)

7) Sequence Dwell

8) Alarm Set

9) Master Unit (See page 8)

9) Pass Code Enable

3.1 DOME TYPE SELECTION

Videolarm designed the VLC485 to support RS485/422 control protocols from a

number of manufacturers. Dome type selection is independent of the camera position,

which means that you can build a system using multiple dome types.

TO CHANGE CAMERA PROTOCOL:

CAM 04

DOME TYPE

VIDEOLARM

Select a camera.

The current pan/tilt type will display.

To select a different type press the

STAR (*) key until the desired type is

displayed.

Press the POUND (#) key to enter the

selection. Press MENU to exit the menu

mode.

Press the MENU button. Enter password

if necessary.

DOME TYPE

SENSORMATIC

3.2 MULTIPLEXER SELECTION

The VLC485 can also support multiplexers from a number of manufacturers to allow

the unit to control even more cameras.

TO SELECT A MULTIPLEXER TYPE:

The VLC485 can connect to one main multiplexer and an additional expansion

multiplexer if this feature is supported by the multiplexer. The main multiplexer is used

to handle camera numbers 1 through 16 while the expansion multiplexer is used to

handle camera numbers 17 through 32.

MUX TYPE

ATV

Use the POUND (#) key to scroll to the

Multiplexer Type. The current type will

be displayed.

Press the STAR (*) key until the desired

type is displayed. Press the POUND (#)

key to select. Press MENU to exit the

menu mode.

Press the MENU button. Enter password

if necessary.

DOME TYPE

HITRON

3.3 PRESET LOCKOUT

TO LOCKOUT THE ABILITY TO SET OR CLEAR PRESETS:

PRESET ENABLE

YES

Use the POUND (#) key to scroll to

Preset Enable. The current setting will

be displayed.

Press the STAR (*) key to change the

setting. Press the POUND (#) key to

select. Press MENU to exit the menu

mode.

Press the MENU button. Enter password

if necessary.

PRESET ENABLE

2.7 ALARMS

Up to 8 alarms can be programmed into the VLC485. When an alarm occurs, the

ALARM message shows in the display window.

CAM 06

ALARM 07

The VLC485 sends a command to that camera telling it to go to the preset point. When

an alarm occurs at that position, the VLC485 will display that camera and alarm. A

beep also sounds from the unit.

To clear an alarm, press the ALARM button.

3.4 AUTO TOUR DWELL (Available only for Videolarm and Kalatel)

Auto tour Dwell denes how long the pan/tilt will stay at each preset in the auto tour.

This parameter is preset in the pan/tilt, but the VLC485 allows you to override that

setting via the menu if this feature is supported by the pan/tilt. A range from 3 to 99

seconds can be set.

SET AUTOTOUR DWELL:

Use the POUND (#) key to scroll to Set

Auto tour Dwell mode.

Use the keypad to enter the desired

dwell time. Press the POUND (#) key

to select. Press MENU to exit the menu

mode.

Press the MENU button. Enter password

if necessary.

SET AUTOTOUR DWELL:

3.5 BEEP ENABLE

Also, if enabled, a brief beep will sound when each button is pressed. To prevent

damage to the joy stick, a beep sound is activated whenever the joystick is at its

maximum position. This function can be disabled in the Menu Mode.

BEEP ENABLE

YES

Use the POUND (#) key to scroll to

Beep Enable. The current setting will be

displayed.

Press the STAR (*) key to change the

setting. Press the POUND (#) key to

select. Press MENU to exit the menu

mode.

Press the MENU button. Enter password

if necessary.

BEEP ENABLE

3.6 SEQUENCING

Sequencing allows you to view up to 16 cameras in a specic order. The sequence can

be set and reviewed and cameras can be added or subtracted using the Menu Mode.

SEQUENCE - ADD CAM:

Use the POUND (#) key to scroll to

Sequence. If a sequence is already set

the rst camera in the sequence will be

displayed.

Press the MENU button. Enter password

if necessary.

SEQUENCE - ADD CAM:

You can review the existing sequence by

pressing the SEQUENCE button. Each

time you press it the next camera will

be displayed. When a blank appears,

that will be the end of the sequence.

1, 2, 3...

3.6.1 TO REVIEW A SEQUENCE

A blank space will appear after the last

camera of the current sequence.

3.6.2 TO ADD A CAMERA TO A SEQUENCE

A sequence may contain up to 16 camera entries. If you have not lled a sequence

and would like to add cameras to it, do the following.

To add a camera to the existing

sequence enter the camera number on

the key pad.

Press the STAR (*) key, then press

the SEQUENCE button. At that point

another blank space will appear.

You may add another camera to the

sequence at this time (up to a total of

16), or press the SEQUENCE button

again to review your entries.

SEQUENCE - ADD CAM:

1, 2, 3...

Using the SEQUENCE button, scroll

through the sequence until you reach

the camera you want to change.

3.6.3 TO CHANGE A CAMERA IN A SEQUENCE

You may change any entry in a sequence at any time. Remember that these

changes overwrite your existing sequence.

SEQUENCE - ADD CAM:

Using the keypad, enter the number of

the camera you want to use.

Press the STAR (*) key, then press the

SEQUENCE button. The number of

the next camera in the sequence will

appear. Press the SEQUENCE button

again to continue to review your entries.

SEQUENCE - ADD CAM:

1, 2, 3...

Press the MENU button. Enter password

if necessary. Use the POUND (#) key to

scroll to Sequence.

Press the MENU button. Enter pass-

word if necessary. Use the POUND (#)

key to scroll to Sequence.

Press the MENU button. Enter pass-

word if necessary. Use the POUND (#)

key to scroll to Sequence.

1, 2, 3...

Using the key pad, enter 00. Press

the STAR (*) key, then press the

SEQUENCE button. The sequence will

be blank.

3.6.4 TO CLEAR THE SEQUENCE

Press the MENU button. Enter password

if necessary. Use the POUND (#) key to

scroll to Sequence.

SEQUENCE - ADD CAM:

3.7 SEQUENCE DWELL

The sequence dwell interval denes how long the camera will stay active in the

sequence. The factory default dwell time is 3 seconds, but this may be changed to any

time between 1 and 99 seconds.

SET SEQUENCE DWELL:

Use the POUND (#) key to scroll to Set

Sequence Dwell. The current dwell time

will be displayed.

Press the MENU button. Enter password

if necessary.

SET SEQUENCE DWELL:

Using the key pad, enter the new dwell

time. Press the STAR (*) key to set the

time. Press MENU to exit the menu

mode.

3.8 CONTROLLER ALARMS

The VLC485 responds to alarms from its alarm inputs. When an alarm occurs, a “go to

preset” command will be sent to a predetermined pan/tilt. For example, alarm 3 may

select preset 23 of camera 7 to be displayed. The preset number and pan/tilt number

are preselected by using the alarm setup function.

CAM 03 ALARM 1

When an alarm occurs, ALARM appears

onscreen. The alarm message can only

be cleared by pressing the ALARM

button.

Press the MENU button. Enter password

if necessary.

ALARM 1 CAM 01

PRESET 03

To set up an alarm, enter the menu

mode and scroll down to the “ALARM:”

entry. Press the

3.9 PASSCODE ENABLE/SET/CHANGE

You can protect your controller from unauthorized alterations by enabling the passcode

function. This means that the menu cannot be accessed without the proper 4-digit. The

VLC485 is factory set with PASSCODE disabled. To enable and set the passcode:

PASSCODE ENABLE:

Use the POUND (#) key to scroll to

Passcode Enable.

Press the MENU button.

PASSCODE ENABLE:

YES

Press STAR (*) to toggle between YES

to enable and NO to disable. Press the

POUND (#) key to enable the selection.

SET PASSCODE:

1234

On selecting YES, the default passcode

will display. Change by entering a new

4-digit code

4.0 PC PORT

The VLC485 uses the PC port to communicate with the serial communications port of

a PC or modem. The PC or other connected device uses a protocol to control either the

VLC485 or other devices connected to the VLC485, such as the pan/tilt units. In addi-

tion, all controller activities, including joystick movements, are transmitted to the PC

port. This enables the controller to become a “peripheral” to a PC and act as the man/

machine interface for a system. Following are the VLC485 protocols.

4.1 PC PORT COMMANDS

VLC485 RS232 COMMUNICATION PROTOCOL

(NOTE: This applies to software version 2.50 and later)

These messages are used to send and receive control messages from the PC.

4.2 GENERAL COMMAND MESSAGE FORMAT

Data is transmitted at 9600 baud, 1 start bit, 1 stop bit, 8 data bits (lsb rst), no parity.

BYTE DATA DESCRIPTION

1 0x7e Start character "~"

2 - n Data All data characters

are 8-bit characters

n+1 0x0d "Carriage return" character

n+2 0x0a "Line feed" character

4.3 MOTION COMMAND MESSAGES

These commands control the basic motion of the pan/tilt platform and the lens

movement of the camera system. The messages all comprise 5 bytes; the Data is

contained in bytes 2 and 3 as described in the following table. Messages that are

transmitted from the controller are indicated by a “T” in the direction column, D;

messages that are received and processed by the controller are indicated by a “R” in

the direction column.

FUNCTION D BYTE #2 BYTE #3 DESCRIPTION

Pan left at speed

"x"

Pan right at

speed "x"

Pan stop

Tilt up at speed

"x"

Tilt down at

speed "x"

Tilt stop

Zoom in

Zoom out

Zoom stop

Focus near

Focus far

Focus stop

Iris open

Iris close

Iris stop

T/R

"1"

"r"

"P"

"u"

"d"

"T"

"Z"

"F"

"I"

"0" - "?"

"S"

"0" - "?"

"S"

"I"

"O"

"S"

"N"

"F"

"S"

"O"

"C"

"S"

Pan left at speed index 0 - 15

Pan right at speed index

0 - 15

Tilt up at speed index 0 - 15

Tilt down at speed index

0 - 15

Zoom in (Telephoto)

Zoom out (Wide angle)

Focus on nearby objects

Focus on distant object

STAR (*) button to scroll to the desired alarm number. The display will show the

camera number and preset associated with the alarm. Use the keypad to enter or

change the camera number and press the CAMERA button. Use the keypad to enter

or change the preset number and press the PRESET button. Press STAR (*) to select

another alarm, or exit the menu by pressing the MENU button.

on the key pad. Press STAR (*), POUND (#) or the MENU button to enable the

passcode and automatically exit the menu mode.

4.4 PRESET AND DOME PARAMETER MESSAGES

These commands control the position presets and some of the operational parameters

of the pan/tilt platform. These messages all comprise 5 bytes; the Data is contained

in bytes 2 and 3 as described in the following table. Messages that are transmitted

from the controller are indicated by a “T” in the direction column, D; messages that

are received and processed by the controller are indicated by an “R” in the direction

column.

FUNCTION D BYTE #2 BYTE #3 DESCRIPTION

Goto preset

position presets

1 - 63

Store preset

position presets

1 - 63

Clear presets

Toggle auto

tour

Set dwell time

T/R

"H"

"P"

"L"

"t"

0x01 -

0x3f

0x01 -

0x3f

"C"

"a"

"0" - "9"

Goto preset position

Store preset position

Clears all presets from

memory

Toggles autotour operation

on and off

Set dwell time in autotour

mode to 1 - 10 seconds

4.5 CONTROLLER PARAMETER MESSAGES

These messages contain information about the controller status. These messages all

comprise 5 bytes; the Data is contained in bytes 2 and 3 as described in the following

table. Messages that are transmitted from the controller are indicated by a “T” in the

direction column, D; messages that are received and processed by the controller are

indicated by a “R” in the direction column.

FUNCTION D BYTE #2 BYTE #3 DESCRIPTION

Camera select

Monitor select

Sequence

status

Sequence

status

Alarm active

Alarm kill

Aux function

aux01 - aux99

Information key

Menu active

Menu inactive

T/R

"C"

"M"

"S"

"A"

"X"

"B"

"M"

0x01 -

0x63

0x01 -

0x63

0x00

0x01

0x01 -

0x0a

"K"

0x01 -

0x6c

"B"

"A"

"I"

Current camera number

Current monitor number

Sequence off

Sequence on

Active alarm number. Alarm

has been detected on alarm

input

Acknowledge all alarms

Toggles aux 1 output

Information key pressed

Controller is in the menu

mode

Controller is not in the menu

mode

4.6 CUSTOM CONTROLLER LCD MESSAGES

If needed, you can write custom messages from your PC for display on the VLC485.

Any information goes only to the controller LCD.

4.6.1 LCD CAPTURE MESSAGE

BYTE DATA DESCRIPTION

4 - 23

"~"

"D"

"0" or "1"

ASCII characters

0x0d

0x0a

Start character

"D" indicates a character string is to be

displayed

This is the LCD line number, either 0 or 1

This is the message string to be displayed

"Carriage return" character

"Line feed" character (optional, ignored)

4.6.2 LCD RELEASE MESSAGE

The display character string message will override any messages displaying on the

VLC485, in essence "capturing" the display.

The display release message will clear the LCD display and allow its use by the

VLC485.

BYTE DATA DESCRIPTION

"~"

"D"

"R"

0x0d

0x0a

Start character

"Carriage return" character

"Line feed" character (optional, ignored)

A message sent to the VLC485 can be cleared at the controller by pressing the

Information button.

RS485

Control

Video

Controller

PC Port Mux Port

Multiplexer

Call Out

Monitor

Main

Monitor

RS485

Control

Video

Controller

PC Port Mux Port

Multiplexer

Call Out

Monitor

Main

Monitor

Typical application

PC System

5.0 MASTER UNIT FUNCTION

The VLC485 can be used in as a stand-alone unit or as part of a system. As part of

a system, the unit may be used with another VLC485 or with a PC. The function is

enabled through the menu.

MASTER UNIT:

Use the POUND (#) key to scroll to

Master Unit.

Press the MENU button.

MASTER UNIT:

YES

Press STAR (*) to toggle between YES

to enable and NO to disable. Press the

POUND (#) key to enable the selection.

Press MENU to exit the menu mode.

Below are diagrams for these types of systems.

Product Registration/Warranty

Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest

quality products available and superior customer service.

Should a problem arise, rest assure that Moog Videolarm stands behind its products by offering impressive warranty plans: 3 Years on all Housings, Poles,

Power Supplies, and Accessories and 5 Years on camera systems (SView, QView, Warriors), and InfraRed Illuminators.

Take a few moments and validate your purchase via the Online Product Registration Form at

www.videolarm.com/productregistration.jsp

• Simple and Trouble-Free RMA process

• Added into customer database to receive product updates / news

• Eliminate the need to archive original purchase documents:

Receipts, Purchase Orders, etc…