Horizon Hobby HAN2345 Manuale del proprietario

Ultra Stick

™

10cc

Instruction Manual

Bedienungsanleitung

Manuel d’utilisation

Manuale di Istruzioni

2

 SPECIFICATIONS • SPEZIFIKATIONEN • SPÉCIFICATIONS • SPECIFICHE  LARGE PARTS LAYOUT • BAUTEILE (OHNE KLEINTEILE) • GRANDES PIÈCES • SCHEMA DEI COMPONENTI GRANDI

60.0 in (1524 mm)

810 sq in (52.3 dm2)

57 in (1448 mm)

7.0 lbs (3.18 kg)

2-Stroke Gas: 10cc

2-Takt Benziner: 10cc

2 temps Essence: 10cc

2-Tempi Gas: 10cc

Electric Power Power: Power 52 Brushless

Elektro Antrieb Power: Power 52 Brushless

Moteur électrique (EP): Power 52 Brushless

Motore elettrico: Power 52 Brushless

4-channel (or greater) with 5 servos

4-Kanal (oder größer) mit 5-Servos

4 voies (ou plus) avec 5 servos

a 4 canali (o più) con 5 servo

Spinner: 2.25-inch

Spinner: 57mm

Cône: 57mm

Ogiva dell’elica: 57mm

4

3

/

4

inches (122mm)

3

2

7

9

10

11

4

5

6

1

12

16

17

15

14

13

8

3

Ultra Stick

™

10cc

Part # English Deutsch Français Italiano

 REPLACEMENT PARTS • ERSATZTEILE • PIÈCES DE RECHANGE • PEZZI DI RICAMBIO

1 HAN234501 Fuselage Rumpf Fuselage Fusoliera

2 HAN234502 Wing with Ailerons and Flaps Flügel mit Querrudern und Klappen Aile avec ailerons et volets Ala con alettoni e ﬂ ap

3 HAN234503 Fin and Rudder Finne u. Seitenruder Dérive et sa gouverne Direzionale e timone

4 HAN234504 Stabilizer and Elevator Höhenruderset Set Plan horizontal et Gouverne de profondeur Set stabilizzatore ed elevatore

5 HAN234506 Landing Gear Set Fahrwerk Set Train d’atterrissage Set del carrello di atterraggio

6 HAN234507 Wheel Pants Radverkleidung Carénage de roue Copriruote

7 HAN234508 Aileron and Flap, Right-Hand Querruder und Klappe, rechte Seite Aileron et volet, côté droit Alettone e ﬂ ap, destro

8 HAN234509 Aileron and Flap, Left-Hand Querruder und Klappe, linke Seite Aileron et volet, côté gauche Alettone e ﬂ ap, sinistro

9 HAN234510 Aileron Set (Not Included) Querrudersatz (Nicht enthalten) Paire d’ailerons (Non fourni) Set alettoni (Non inclusa)

10 HAN234511 Hardware Set Kleinteile Set Sachet de visserie Set dei pezzi

11 HAN234513 Fuselage Hatch Rumpfklappe Capot du fuselage Portello della fusoliera

12 HAN234514 Wheels Räder Roues Ruote

13 HAN234515 EP Tray EP-Halterung Support EP Supporto motore elettrico

14 HAN234517 Tail Wheel Assembly Spornrad m. Zbh. Assemblage de roulette de queue Gruppo del ruotino di coda

15 HAN234518 Fuel tank 15oz Kraftstofftank Réservoir de carburant Serbatoio carburante

16 HAN234519 Engine Mount Set Motor-Montagesatz Jeu de renfort moteur Set di montaggio motore

17 HAN234520 Spinner: 2.25-inch Spinner: 57mm Cône: 57mm Ogiva dell’elica: 57mm

 SMALL PARTS (NOT SHOWN)•KLEINTEILE (NICHT ABGEBILDET)•PETITES PIÈCES (NON REPRÉSENTÉES)•PARTI DI PICCOLE DIMENSIONI (NON MOSTRATE)

HAN234512 Decal Set Dekorbogen Planche de décoration Set di decalcomanie

HAN234516 Pushrod Set Gestänge / Anlenkungen Set Jeu de tringleries Set dell’asta di spinta

 ELECTRIC POWER • ELEKTROANTRIEB • MOTEUR ELECTRIQUE (EP) • MOTORE ELETTRICO

APC14085E Electric Propeller, 14 x 8.5E Elektro Propeller, 14 x 8,5E Hélice électrique, 14 x 8,5E Elica elettrica sottile, 14 x 8,5E

EFLA1060B 60-Amp Pro SB Brushless ESC (V2) 60-Amp Pro SB Brushless ESC (V2) Variateur ESC sans balais avec circuit SB pro 60 A (V2) 60-Amp Pro SB Brushless ESC (V2)

EFLAEC509 or EC5 Device To EC3 Battery 1.5-inch, 12 AWG EC5-Gerät an EC3-Akku 76mm (1,5 Zoll), 12AWG Dispositif EC5 vers batterie EC3, 1,5po, 12AWG

Adattatore dispositivo EC5 a batteria EC3 3,8 cm

(1,5’’), 12 AWG

EFLAEC501 EC5 Device Connector (2) EC5 Gerät-Steckverbinder (2) Connecteur du dispositif EC5 (2) Connettore dispositivo EC5 (2)

EFLB50005S30 5000mAh 5S 18.5V 30C LiPo,12AWG EC3 5000mA 5S 18,5 V 30C LiPo-Akku,12 AWG EC3

Batterie Li-Po 5S 18,5V 5000mA 30C, 12AWG prise

EC3

Batteria LiPo 30C 18,5 V 5S 5000 mAh, 12AWG

EC3

EFLM4052A Power 52 BL Outrunner Mtr, 590Kv Bürstenloser Außenläufer-Motor Leistung 52, 590Kv

Moteur à cage tournante sans balais Power 52 de

590Kv

Motore brushless a cassa rotante Power 52,

590Kv

SPMSA6110 x6 A6110 HV Standard Servo A6110 HV Standard Servo Servo standard A6110 HV Servo standard A6110 HV

4

Part # English Deutsch Français Italiano

 2-STROKE GAS • 2-TAKT BENZINER • 2 TEMPS ESSENCE • 2-TEMPI A BENZINA

APC12060 Sport Propeller, 12 x 6 Sportpropeller, 12 x 6 Hélice sport, 12 x 6 Elica sport, 12 x 6

EVOA112 Evolution 3 Wire Ignition/RX Switch Evolution Zündschalter Interrupteur Evolution 3 ﬁ ls Allumage/RX

Evolution, interruttore a 3 ﬁ li accensione/

ricevitore

EVOE10GX2 10GX Gas Engine w/ Pumped Carb Evolution 10-cc Evolution 10-cc Evolution 10-cc

SPM9530 Spektrum

™

3-Wire Switch Harness Spektrum dreiadriges Schalterkabel Câblage d’interrupteur 3 ﬁ ls Spektrum Interruttore di accensione a 3 ﬁ li Spektrum

SPMB2000LPRX 2000mAh 2S 7.4V LiPo Rx Battery LiPo-Empfängerakku (7,4 V / 2000 mAh) Batterie Li-Po de récepteur 7,4 V 2000 mAh Batteria per ricevitore da 7,4 V Li-Po, 2000 mAh

SPMB900LFRX 900mAh 2S 6.6V Li-Fe Rx Battery 900 mA 2S 6,6 V LiFe Empfänger-Akku Batterie récepteur Li-Fe 2S 6,6V 900mA Batteria LiFe per ricevente 2S 6,6 V 900 mAh

SPMSA6110 x7 A6110 HV Standard Servo A6110 HV Standard Servo Servo standard A6110 HV Servo standard A6110 HV

EVOA102 Medium Gas-FKM Fuel Tubing (1 meter) Mittlere Gas-FKM Kraftstofﬂ eitung (1 Meter) Tuyau de carburant en FKM moyen (1 mètre) Tubo per combustibile FKM medio (1 metro)

 REQUIRED RADIO EQUIPMENT • ERFORDERLICHE RC AUSRÜSTUNG • ÉQUIPEMENT RADIO REQUIS • APPARECCHIATURE RADIO NECESSARIE

SPMA3000 x2 Heavy-Duty Servo Extension 3-inch Servokabelverlängerung 75 mm (3 inch) Rallonge de servo, 75 mm Estensione servo 3 pollici

SPMA3001 x4 Heavy-Duty Servo Extension 6-inch Servokabelverlängerung 150 mm (6 inch) Rallonge de servo, 150 mm Estensione servo 6 pollici

SPMA3002 x2 Heavy-Duty Servo Extension 9-inch Servokabelverlängerung 230 mm (9 inch) Rallonge de servo, 230 mm Estensione servo 9 pollici

SPMAR7350 AR7350 7 Channel AS3X Receiver AR7350 7 Kanal AS3X RX mit integrierter Telemetrie

Récepteur Spektrum AR7350 7 voies AS3X avec

télémétrie intégrée

Ricevente AR7350 AS3X 7 canali con telemetria

integrata

 OPTIONAL ITEMS • OPTIONALE TEILE • ÉLÉMENTS OPTIONNELS • ARTICOLI OPZIONALI

DYNC2010CA Prophet Sport Plus 50W AC/DC Charger

Prophet Sport Plus 50W Wechsel-/Gleichstrom-

Ladegerät

Chargeur CA/CC 50W Prophet Sport Plus Caricabatterie Prophet Sport Plus 50W AC

SPMA3054 Servo Connector Clips (25) Servosteckerklemmen (25) Attaches de connexion du servo (25) Morsetti servocomando (25)

SPMAR9350 AR9350 9-Channel AS3X Receiver AR9350 AS3X-Empfänger mit 9 Kanälen Récepteur AS3X 9canaux AR9350 Ricevitore AS3X a 9 canali AR9350

 OPTIONAL FLOATS•OPTIONALE SCHWIMMER•FLOTTEURS OPTIONNELS•GALLEGGIANTI OPZIONALI

EFLA5600 Carbon-Z Float Set Carbon-ZSchwimmersatz Ensemble de ﬂ otteurs Carbon-Z Set galleggianti Carbon-Z

EFLA5605

Wire Mounting Set for CZ Cessna 150:

Carbon-Z Floats

Kabelbefestigungssatz CZ für Cessna 150:

Carbon-ZSchwimmer

Ensemble pour montage de câbles pour CZ Cessna

150: ﬂ otteurs Carbon-Z

Set montaggio ﬁ li per CZ Cessna 150:

Galleggianti Carbon-Z

SPMA3001 Heavy-Duty Servo Extension 6-inch Servokabelverlängerung 150 mm (6 inch) Rallonge de servo, 151 mm Estensione servo 6 pollici

SPMA3058 Standard Y-Harness, 6-inch Standard Y-Kabelbaum, 152mm (6 Zoll) Rallonge Y standard, 15cm Cavo a Y standard, 6''

DUB158 Landing Gear Straps Halteriemen des Fahrwerks Sangles du train d’atterrissage Piastrine carrello d’atterraggio

 REQUIRED ADHESIVES • ERFORDERLICHE KLEBSTOFFE • TYPES DE COLLES • ADESIVI NECESSARI

DLMAD44 Roket Rapid CA 5-10 sec: 20g Roket Rapid CA 5-10 s: 20g Colle cyano Roket Rapid 5-10 sec: 20g Colla cianoacrilica Roket Rapid 5-10 sec: 20 g

DLMAD45 Roket Max CA 10-20 sec: 20g Roket Max CA 10-20 s: 20g Colle cyano Roket Max 10-20 sec: 20g Colla cianoacrilica Roket Max 10-20 sec: 20 g

PAAPT715 CA Accelerator Sekundenkleber (CA) Aktivator Accélérateur de colle CA Accelerante colla CA

PAAPT35 15-Minute Epoxy 15 Minuten Epoxy Époxy 15 minutes Colla epoxy 15 minuti

PAAPT42 Threadlock Schraubensicherungslack Frein-ﬁ let Frenaﬁ letti

DLMAD12 R/C Modeller Canopy Glue: 4 oz R/C Modeller Kanzelkleber: 113,4g (4 oz) Colle à verrière R/C Modeller: 113g Colla per capottine R/C Modeller: 4 oz

5

Ultra Stick

™

10cc

Part # English Deutsch Français Italiano

 REQUIRED TOOLS • BENÖTIGTES WERKZEUG • OUTILS REQUIS • ATTREZZI NECESSARI

Box wrench: 1/2-inch Ringschlüssel: 1/2-inch Clé hexagonale: 1/2-inch Chiave esagonale: 1/2-inch

Drill Bohrer Mini-perceuse Trapano

Drill bit: 1/16-inch, 5/64-inch, 1/8-inch

5/32-inch, 3/16-inch

Bohrer: 1,5mm, 2mm, 3mm, 4mm, 4,5mm Forêt : 1,5mm, 2mm, 3mm, 4mm, 4,5mm

Punte per trapano: 1,5mm, 2mm, 3mm, 4mm,

4,5mm

Felt-tipped pen Faserstift Feutre ﬁ n effaçable Pennarello

Epoxy brush Pinsel Pinceau Epoxy Spazzole epoxy

Flat ﬁ le Flachfeile Lime plate Lima piatta

Hemostats Klemme Pince Hemostat Pinzetta

Hex wrench: 3/32-inch, 1.5mm, 2mm, 2.5mm,

3mm, 4mm

Inbusschlüssel: 3/32-inch, 1,5mm, 2mm, 2,5mm,

3mm, 4mm

Tournevis hexagonal: 3/32-inch, 1,5mm, 2mm, 2,5mm,

3mm, 4mm

Chiave esag.: 3/32-inch, 1,5mm, 2mm, 2,5mm,

3mm, 4mm

Hobby knife with #11 blade Hobbymesser mit # 11 Klinge Couteau : Lame numéro 11 Taglierino: #11 lama

Isoplrpyl alcohol Isopropyl Alkohol Alcool isopropylique Alcol isopropilico

Low-tack tape Kreppband Adhésif de masquage Nastro a bassa aderenza

Needle nose pliers Spitzzange Pince ﬁ ne Pinze a becco stretto

Nut driver: 1/4-inch, 4mm, 5.5mm Steckschlüssel. 1/4-inch, 11/32-inch Clés à douilles : 1/4-inch, 11/32 pouce Chiave per dadi: 1/4-inch, 11/32-inch

Paper towels Papiertücher Papier absorbant Asciugamani di carta

Pencil Stift Crayon à papier Matita

Phillips screwdriver: #1 Phillips Schraubendreher: #1 Tournevis cruciforme: #1 Cacciavite a croce: #1

Pin vise Handbohrer Porte forets Trapano manuale

Pliers Zange Pince Pinze

Ruler Lineal Réglet Righello

Sandpaper Schleifpapier Papier de verre Carta vetrata

Scissors Schere Ciseaux Forbici

Side cutters Seitenschneider Pince coupante Lama laterale

Square Geodreieck Équerre Squadra

Tap and drill set, English Gewindeschneider und Bohrerset Taraud et foret Set punte e maschi, Inglese

Tap Handle Halter für Gewindeschneider Épingles Impugnatura per maschiare

T-pins T- Nadeln Epingles Spilli a T

Toothpicks Zahnstocher Cure dents Stuzzicadenti

6

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon

Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

The following terms are used throughout the product literature to indicate various levels of potential harm when

operating this product:

Meaning of Special Language

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,

and serious injury OR create a high probability of superﬁ cial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a

possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or

no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.

Failure to operate the product correctly can result in damage to the product, personal property and cause serious

injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic

mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage

to the product or other property. This product is not intended for use by children without direct adult supervision. Do

not attempt disassembly, use with incompatible components or augment product in any way without the approval

of Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to

read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate

correctly and avoid damage or serious injury.

AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT A TOY.

 USING THE MANUAL

This manual is divided into sections to help make assembly easier to understand.

 SAFETY WARNINGS AND PRECAUTIONS

Read and follow all instructions and safety precautions before use. Improper use can result in ﬁ re, serious injury and

damage to property.

Components

Use only with compatible components. Should any compatibility questions exist, please refer to the product

instructions, component instructions or contact the appropriate Horizon Hobby ofﬁ ce.

Flight

Fly only in open areas to ensure safety. It is recommended ﬂ ying be done at radio control ﬂ ying ﬁ elds. Consult local

ordinances before choosing a ﬂ ying location.

Propeller

Keep loose items that can become entangled in the propeller away from the prop. This includes loose clothing or other

objects such as pencils and screwdrivers. Keep your hands away from the propeller as injury can occur.

Batteries

Always follow the manufacturer’s instructions when using and disposing of any batteries. Mishandling of Li-Po

batteries can result in ﬁ re causing serious injury and damage.

Small Parts

This kit includes small parts and should not be left unattended near children as choking and serious injury could result.

 SAFE OPERATING RECOMMENDATIONS

• Inspect your model before every ﬂ ight to ensure it is airworthy.

• Be aware of any other radio frequency user who may present an interference problem.

• Always be courteous and respectful of other users in your selected ﬂ ight area.

• Choose an area clear of obstacles and large enough to safely accomodate your ﬂ ying activity.

• Make sure this area is clear of friends and spectators prior to launching your aircraft.

• Be aware of other activities in the vicinity of your ﬂ ight path that could cause potential conﬂ ict.

• Carefully plan your ﬂ ight path prior to launch.

• Abide by any and all established AMA National Model Aircraft Safety Code.

 BEFORE STARTING ASSEMBLY

• Remove parts from bag.

• Inspect fuselage, wing panels, rudder and stabilizer for damage.

• If you ﬁ nd damaged or missing parts, contact your place of purchase.

If you ﬁ nd any wrinkles in the covering, use a heat gun (HAN100) and covering glove (HAN150) or covering iron

(HAN101) with a sealing iron sock (HAN141) to remove them. Use caution while working around areas where the colors

overlap to prevent separating the colors.

• Charge transmitter and receiver batteries.

• Center trims and sticks on your transmitter.

• For a computer radio, create a model memory for this particular model.

• Bind your transmitter and receiver, using your radio system’s instructions.

IMPORTANT: Rebind the radio system once all control throws are set. This will keep the servos from moving to

their endpoints until the transmitter and receiver connect. It will also guarantee the servo reversal settings are

saved in the radio system.

7

Ultra Stick

™

10cc

Propeller

Halten Sie lose Gegenstände die sich im Propeller verfangen können weg vom Propeller. Dieses gilt auch für Kleidung

oder andere Objekte wie zum Beispiel Stifte oder Schraubendreher.

Halten Sie ihre Hände weg vom Propeller, es besteht akute Verletzungsgefahr.

Akkus

Folgen Sie immer den Herstelleranweisungen bei dem Gebrauch oder Entsorgung von Akkus. Falsche Behandlung von

LiPo Akkus kann zu Feuer mit Körperverletzungen und Sachbeschädigung führen.

Kleinteile

Dieser Baukasten beinhaltet Kleinteile und darf nicht unbeobachtet in der Nähe von Kindern gelassen werden, da die

Teile verschluckt werden könnten mit ernsthaften Verletzung zur Folge.

 EMPFEHLUNGEN ZUM SICHEREN BETRIEB

• Überprüfen Sie zur Flugtauglichkeit ihr Modell vor jedem Flug.

• Beachten Sie andere Piloten deren Sendefrequenzen ihre Frequenz stören könnte.

• Begegnen Sie anderen Piloten in ihrem Fluggebiet immer höﬂ ich und respektvoll.

• Wählen Sie ein Fluggebiet, dass frei von Hindernissen und groß genug ist.

• Stellen Sie vor dem Start sicher, dass die Fläche frei von Freunden und Zuschauern ist.

• Beobachten Sie den Luftraum und andere Flugzeuge/Objekte die ihren Flugweg kreuzen und zu einem Konﬂ ikt

führen könnten.

• Planen Sie sorgfältig ihren Flugweg vor dem Start.

 VOR DEM ZUSAMMENBAU

• Entnehmen Sie zur Überprüfung jedes Teil der Verpackung.

• Überprüfen Sie den Rumpf, Tragﬂ ächen, Seiten- und Höhenruder auf Beschädigung.

• Sollten Sie beschädigte oder fehlende Teile feststellen, kontaktieren Sie bitte den Verkäufer.

Zum Entfernen von Falten in der Bespannung verwenden Sie den Heißluftfön (HAN100) und Bespannhandschuh

(HAN150) oder das Folienbügeleisen (HAN141). Bitte achten Sie bei überlappenden Farben, dass Sie diese sich bei

dem Bearbeitung nicht trennen.

• Laden des Senders und Empfängers.

• Zentrieren der Trimmungen und Sticks auf dem Sender.

• Sollten Sie einen Computersender verwenden, resetten Sie einen Speicherplatz und benennen ihn nach dem Modell.

• Sender und Empfänger jetzt nach den Bindeanweisung des Herstellers zu binden.

WICHTIG: Wir empfehlen dringend nachdem alle Einstellungen vorgenommen worden sind, das Modell neu zu binden.

Dieses verhindert, dass die Servos in die Endanschläge laufen bevor sich Sender und Empfänger verbunden haben. Es

garantiert auch, dass die Servoreverseeinstellungen in der RC Anlage gesichert sind.

HINWEIS

Alle Anweisungen, Garantien und anderen zugehörigen Dokumente können im eigenen Ermessen von Horizon Hobby,

LLC. jederzeit geändert werden Die aktuelle Produktliteratur ﬁ nden Sie auf horizonhobby.com unter der Registerkarte

„Support“ für das betreffende Produkt.

Spezielle Bedeutungen

Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe

Gefahrenrisiken beim Betrieb dieses Produkts hinzuweisen:

WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden,

Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberﬂ ächliche Verletzungen.

ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die

Gefahr von schweren Verletzungen.

HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe

oder keine Gefahr von Verletzungen ergeben.

WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den Produktfunktionen

vertraut zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu Schäden am Produkt oder persönlichem

Eigentum führen oder schwere Verletzungen verursachen.

Dies ist ein hochentwickeltes Hobby-Produkt. Es muss mit Vorsicht und gesundem Menschenverstand betrieben

werden und benötigt gewisse mechanische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere und

verantwortungsvolle Weise betrieben, kann dies zu Verletzungen oder Schäden am Produkt oder anderen Sachwerten

führen. Dieses Produkt eignet sich nicht für die Verwendung durch Kinder ohne direkte Überwachung eines

Erwachsenen. Verwenden Sie das Produkt nicht mit inkompatiblen Komponenten oder verändern es in jedweder Art

ausserhalb der von Horizon Hobby, LLC vorgegebenen Anweisungen. Diese Bedienungsanleitung enthält Anweisungen

für Sicherheit, Betrieb und Wartung. Es ist unbedingt notwendig, vor Zusammenbau, Einrichtung oder Verwendung

alle Anweisungen und Warnhinweise im Handbuch zu lesen und zu befolgen, damit es bestimmungsgemäß betrieben

werden kann und Schäden oder schwere Verletzungen vermieden werden.

NICHT GEEIGNET FÜR KINDER UNTER 14 JAHREN. DIES IST KEIN SPIELZEUG.

 ÜBER DIESE ANLEITUNG

Diese Anleitung ist zur Vereinfachung des Zusammenbaues in Sektionen unterteilt.

 WARNUNGEN UND SICHERHEITS-VORKEHRUNGEN

Bitte lesen und befolgen Sie alle Anweisungen und Sicherheitsvorkehrungen vor dem Gebrauch. Falscher, nicht

sachgemäßer Gebrauch kann Feuer, ernsthafte Verletzungen und Sachbeschädigungen zur Folge haben.

Komponenten

Verwenden Sie mit dem Produkt nur kompatible Komponenten. Sollten Fragen zur Kompatibilität auftreten, lesen Sie

bitte die Produkt- oder Bedienungsanweisung oder kontaktieren den Service von Horizon Hobby.

Fliegen

Fliegen Sie um Sicherheit garantieren zu können, nur in weiten offenen Gegenden. Wir empfehlen hier den Betrieb auf

zugelassenen Modellﬂ ugplätzen. Bitte beachten Sie lokale Vorschriften und Gesetze, bevor Sie einen Platz zum Fliegen

wählen.

8

L’hélice

Gardez éloignés tous les éléments qui pourraient être attrapés par l’hélice. Cela inclut les vêtements larges ou les

objets comme des outils par exemple. Gardez toujours vos mains à distance pour éviter tout cas de blessures.

Les batteries

Suivez toujours les instructions du fabricant de vos batteries. Une mauvaise manipulation d’une batterie Li-Po peut

entraîner un incendie causant de graves dégâts matériels et des blessures corporelles.

Petites pièces

Ce kit contient des petites pièces qui ne doivent pas être laissées à la portée des enfants, ces pièces sont dangereuses

pour eux et peuvent entraîner de graves blessures.

 CONSIGNES DE SÉCURITÉ CONCERNANT L’UTILISATION

• Inspectez votre modèle avant chaque vol.

• Surveillez les fréquences utilisées à proximité.

• Soyez toujours courtois et respectueux des autres utilisateurs de la zone de vol.

• Choisissez une zone dégagée de tout obstacle et sufﬁ samment grande pour voler en toute sécurité.

• Contrôlez que la zone est libre de spectateurs avant de lancer votre modèle.

• Soyez conscient des autres activités aux alentours de votre vol, risque de conﬂ it potentiel.

• Planiﬁ ez votre vol avant de le commencer.

 AVANT DE COMMENCER L’ASSEMBLAGE

• Retirez toutes les pièces des sachets pour les inspecter.

• Inspectez soigneusement le fuselage, les ailes et les empennages.

• Si un élément est endommagé, contactez votre revendeur.

Si l’entoilage présente quelque plis, vous pouvez les lisser en utilisant le pistolet à air chaud (HAN100) et le gant

(HAN150) ou le fer à entoiler (HAN101) avec la chaussette de protection (HAN141). Agissez soigneusement dans les

zones où plusieurs couleurs d’entoilage sont superposées aﬁ n d’éviter de les séparer.

• ll est recommandé de préparer tous les éléments du système de la radio.

• Cela inclut la charge des batteries comme la mise au neutre des trims et des manches de votre émetteur.

• Si vous utilisez une radio programmable, sélectionnez une mémoire libre aﬁ n d’y enregistrer les paramètres de ce

modèle.

• Nous vous recommandons d’affecter maintenant le récepteur à l’émetteur en suivant les instructions fournies avec

votre radio.

IMPORTANT: Il est hautement recommandé de ré-affecter le système une fois que les courses seront réglées. Cela

empêchera les servos d’aller en butée lors de la connexion du système. Cela garantit également que la direction des

servos est enregistrée dans l’émetteur.

REMARQUE

La totalité des instructions, garanties et autres documents est sujette à modiﬁ cation à la seule discrétion d’Horizon

Hobby, LLC. Pour obtenir la documentation àjour, rendez-vous sur le site horizonhobby.com et cliquez sur l’onglet de

support de ce produit.

Signiﬁ cation de certains termes spéciﬁ ques

Les termes suivants sont utilisés dans l’ensemble du manuel pour indiquer différents niveaux de danger lors de

l’utilisation de ce produit:

AVERTISSEMENT: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels

et des blessures graves OU engendrer une probabilité élevée de blessure superﬁ cielle.

ATTENTION: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET des

blessures graves.

REMARQUE: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET

éventuellement un faible risque de blessures.

AVERTISSEMENT: Lisez la TOTALITÉ du manuel d’utilisation aﬁ n de vous familiariser avec les caractéristiques du

produit avant de le faire fonctionner. Une utilisation incorrecte du produit peut entraîner sa détérioration, ainsi que des

risques de dégâts matériels, voire de blessures graves.

Ceci est un produit de loisirs sophistiqué. Il doit être manipulé avec prudence et bon sens et requiert des aptitudes

de base en mécanique. Toute utilisation irresponsable de ce produit ne respectant pas les principes de sécurité peut

provoquer des blessures, entraîner des dégâts matériels et endommager le produit. Ce produit n’est pas destiné à

être utilisé par des enfants sans la surveillance directe d’un adulte. N’essayez pas de modiﬁ er ou d’utiliser ce produit

avec des composants incompatibles hors des instructions fournies par Horizon Hobby, LLC. Ce manuel comporte des

instructions relatives à la sécurité, au fonctionnement et à l’entretien. Il est capital de lire et de respecter la totalité

des instructions et avertissements du manuel avant l’assemblage, le réglage et l’utilisation, ceci aﬁ n de manipuler

correctement l’appareil et d’éviter tout dégât matériel ou toute blessure grave.

14 ANS ET PLUS. CECI N’EST PAS UN JOUET.

 UTILISATION DU MANUEL

Ce manuel est divisé en sections pour vous aider à comprendre plus facilement l’assemblage.

 AVERTISSEMENTS RELATIFS À LA SÉCURITÉ

Lisez et suivez toutes les instructions relatives à la sécurité avant utilisation. Une utilisation inappropriée peut entraîner

un incendie, de graves blessures et des dégâts matériels.

Composants

Utilisez uniquement des composants compatibles. Si vous avez des questions concernant la compatibilité, référez-vous

à ce manuel ou contactez le service technique Horizon Hobby.

Le vol

Volez uniquement dans des zones dégagées pour un maximum de sécurité. Il est recommandé d’utiliser les pistes des

clubs d’aéromodélisme. Consultez votre mairie pour connaître les sites autorisés.

9

Ultra Stick

™

10cc

AVVISO

Tutte le istruzioni, le garanzie e gli altri documenti pertinenti sono soggetti a cambiamenti a totale discrezione di

Horizon Hobby, LLC. Per una documentazione aggiornata sul prodotto, visitare il sito www.horizonhobby.com e fare

clic sulla sezione Support per questo prodotto.

Signiﬁ cato dei termini particolari

In tutta la documentazione relativa al prodotto sono utilizzati iseguenti termini per indicare vari livelli di potenziale

pericolo durante il funzionamento:

AVVERTENZA: Procedure che, se non debitamente seguite, espongono alla possibilità di danni alla proprietà ﬁ sica

opossono omportare un’elevata possibilità di provocare ferite superﬁ ciali. Ulteriori precauzioni per la sicurezza e

avvertenze.

ATTENZIONE: Procedure che, se non sono seguite correttamente, possono creare danni materiali E possibili gravi

lesioni.

AVVISO: Procedure che, se non sono seguite correttamente, possono creare danni materiali E nessuna oscarsa

possibilità di lesioni.

AVVERTENZA: Leggere TUTTO il manuale di istruzioni e prendere familiarità con le caratteristiche del prodotto, prima

di farlo funzionare. Un utilizzo scorretto del prodotto può causare danni al prodotto stesso, alle persone oalle cose,

provocando gravi lesioni.

Questo è un prodotto di hobbistica soﬁ sticato e NON un giocattolo. È necessario farlo funzionare con cautela e

responsabilità e avere conoscenze basilari di meccanica. Se questo prodotto non è utilizzato in maniera sicura e

responsabile potrebbero veriﬁ carsi lesioni odanni al prodotto stesso oad altre proprietà. Non è un prodotto adatto

aessere utilizzato dai bambini senza la diretta supervisione di un adulto. Non usare componenti non compatibili

o alterare il prodotto in nessuna maniera al di fuori delle istruzioni fornite da Horizon Hobby, LLC. Questo manuale

contiene le istruzioni per un funzionamento e una manutenzione sicuri. È fondamentale leggere e seguire tutte le

istruzioni e le avvertenze del manuale prima di montare, conﬁ gurare ofar funzionare il Prodotto, al ﬁ ne di utilizzarlo

correttamente e di evitare danni olesioni gravi.

MINIMO 14 ANNI. NON È UN GIOCATTOLO.

 COME USARE IL MANUALE

Questo manuale è diviso in sezioni per rendere più facile la comprensione del montaggio.

 AVVERTIMENTI E PRECAUZIONI PER LA SICUREZZA

Prima dell’uso leggere attentamente tutte le istruzioni e le precauzioni per la sicurezza. In caso contrario si potrebbero

procurare incendi, danni o ferite.

Componenti

Usare solo componenti compatibili. Se ci fossero dubbi riguardo alla compatibilità, è opportuno far riferimento alle

istruzioni relative al prodotto o ai componenti oppure rivolgersi al reparto Horizon Hobby di competenza.

Volo

Per sicurezza volare solo in aree molto ampie. Meglio se in campi volo autorizzati per modellismo. Consultare le

ordinanze locali prima di scegliere luogo dove volare.

Elica

Tenere gli oggetti liberi (vestiti, penne, cacciaviti, ecc.) lontano dall’elica, prima che vi restino impigliati. Bisogna fare

attenzione anche con le mani perché c’è il rischio di ferirsi anche gravemente.

Batterie

Quando si maneggiano o si utilizzano le batterie, bisogna attenersi alle istruzioni del costruttore; il rischio è di procurare

incendi, specialmente con le batterie LiPo, con danni e ferite serie.

Piccole parti

Questo kit comprende delle parti di piccole dimensioni e non lo si può lasciare incustodito se c’è la presenza di bambini

che li possono inghiottire e rimanere soffocati o intossicati.

 RACCOMANDAZIONI PER OPERARE IN SICUREZZA

• Controllare attentamente il modello prima di ogni volo per accertarsi che sia idoneo.

• Essere consapevoli che un altro utente della frequenza in uso, potrebbe procurare delle interferenze.

• Essere sempre cortesi e rispettosi nei confronti degli altri utilizzatori dell’area in cui ci si trova.

• Scegliere un’area libera da ostacoli e abbastanza ampia da permettere lo svolgimento del volo in sicurezza.

• Prima del volo veriﬁ care che l’area sia libera da amici e spettatori.

• Stare attenti alle altre attività che si svolgono in vicinanza della vostra traiettoria di volo, per evitare possibili conﬂ itti.

• Pianiﬁ care attentamente il volo prima di lanciare il modello.

• Rispettare sempre scrupolosamente le regole stabilite dall’associazione locale.

 PRIMA DI INIZIARE IL MONTAGGIO

• Togliere tutti i pezzi dalla scatola.

• Veriﬁ care che la fusoliera, l’ala e i piani di coda non siano danneggiati.

• Se si trovano parti danneggiate, contattare il negozio da cui è stato acquistato.

Se si trovano delle pieghe nella ricopertura, si possono togliere usando una pistola ad aria calda (HAN100) e guanto per

ricopertura (HAN150), oppure un ferro per ricopertura (HAN101) con la sua calza di protezione (HAN141). Usare cautela

quando si lavora in aree del rivestimento dove ci sono dei colori sovrapposti, per evitare la loro separazione.

• Caricare il trasmettitore e la batteria di volo.

• Centrare stick e trim sul trasmettitore.

• Con una radio computerizzata creare una nuova memoria per questo modello.

• Facendo riferimento alle istruzioni del radiocomando, connettere (bind) trasmettitore e ricevitore.

IMPORTANTE: Ripetere la procedura di connessione una volta regolate le corse, per evitare che i servi vadano a ﬁ ne

corsa. Garantirà anche che le impostazioni di inversione del servo vengano salvate nel sistema radio.

10

 BUILDING PRECAUTIONS

During assembly, we recommend resting the parts on a

soft surface such as a soft towel to help prevent denting

the sheeting.

 REMOVING WRINKLES

The covering of your model may develop wrinkles during

shipping and will require the use of a heat gun (HAN100)

and covering glove (HAN150) or covering iron (HAN101)

with a sealing iron sock (HAN141) to remove them. Use

caution while working around areas where the colors

overlap to prevent separating the colors. Avoid using

too much heat, which could separate the colors. Placing

a cool damp cloth on adjacent colors will also help in

preventing the separation of the colors while removing

wrinkles.

 FLUORESCENT COVERING PRECAUTION

The ﬂ uorescent covering used on your model can

fade with exposure to direct sunlight over time. We

recommend keeping your model out of direct sunlight for

prolonged periods if possible.

 TRANSPORTATION AND STORAGE

When transporting and storing your model, you will

need a minimum of 80 inches (2m) in length, and 18

inches (46cm) in height to accommodate the size of the

fuselage. We also recommend the use of a wing bag

and stabilizer bags to help protect these surfaces during

transport and storage. The control horns and linkages can

also cause damage to nearby surfaces even when placed

in storage bags. Always place surfaces so the tops are

together to prevent damage from the control horns and

linkages.

 HINWEISE ZUM BAU

Während des Zusammenbaus empfehlen wird, dass die

Teile auf einer weichen Oberﬂ äche, wie einem Handtuch,

abgelegt werden, um ein Eindrücken der Bleche zu

verhindern.

 ENTFERNEN VON FALTEN

Während des Transportes können bei der Bespannung

Falten aufgetreten sein. Sie können diese mit dem

Heißluftfön (HAN100) und Bespannhandschuh (HAN150)

oder dem Bügeleisenbezug (HAN141) entfernen. Bitte

achten Sie bei überlappenden Farben diese nicht durch

zuviel Hitze zu lösen. Ein kühlendes Stück Stoff kann hier

neben den Falten aufgelegt helfen, dass die Farben sich

nicht trennen.

 VORSICHTSMASSNAHMEN BEI DER

FLUORESZIERENDEN ABDECKUNG

Die auf dem Modell verwendete ﬂ uoreszierende

Abdeckung kann bei direkter Sonneneinstrahlung im

Laufe der Zeit verblassen. Wir empfehlen, das Modell

über längere Zeiträume möglichst keinem direkten

Sonnenlicht auszusetzen.

 TRANSPORT UND LAGERUNG

Bei dem Transport des Modells benötigen Sie mindestens

2 Meter Länge und 46cm Höhe für den Rumpf. Wir

empfehlen ebenfalls Flächen- und Leitwerkstaschen um

Transportschäden zu vermeiden. Durch die Ruderhörner

können ebenfalls Flächen beschädigt werden, so dass

diese nur mit den Oberseiten zueinander gelagert werden

sollten.

 MONTAGE DER OPTIONALEN

SCHWIMMER

Bei der Montage der empfohlenen Schwimmer auf

dem Ultra Stick 10cc sicherstellen, die unter Optionale

Schwimmer aufgeführten Teile zu verwenden.

 EMPFOHLENE SERVOS UND

GESCHWINDIGKEITSREGLER

Bei der Verwendung der empfohlenen Servos und

Geschwindigkeitsregler funktionieren die Servos

möglicherweise etwas langsamer als erwartet. Dies

wurde vollständig getestet und das Modell wird mit dieser

Kombination perfekt funktionieren. Zum Erreichen einer

optimalen Leistung der Servos kann das im Empfänger

eingesteckte rote Kabel vom Geschwindigkeitsregler

entfernt und ein separater Empfänger-Akku verwendet

werden, laut der Empfehlung der aufgeführten Teile für

den 2-Takt-Benziner.

 KOMBINATIONEN AUS MOTOR, AKKU

UND PROPELLER

Wir haben eine Vielzahl von Kombinationen aus Motor,

Akku und Propeller getestet. Das Nachfolgende ist das

Ergebnis dieser Tests.

• Bei der Verwendung von Power 52 Motor, 5S 5000mA

Akku und 14 x 8,5E APC Propeller empfehlen

wir mindestens die Verwendung eines 60A

Geschwindigkeitsreglers (ELFA1060B).

• Bei der Verwendung von Power 52 Motor, 6S

5000mA Akku und 14 x 6E APC Propeller empfehlen

wir mindestens die Verwendung eines 80A

Geschwindigkeitsreglers (EFLA1080B).

• Bei der Verwendung von Power 52 Motor, 5S

5000mA Akku und 15 x 8E APC Propeller empfehlen

wir mindestens die Verwendung eines 60A

Geschwindigkeitsreglers (EFLA1060B).

 OPTIONAL FLOAT INSTALLATION

When installing the recommended ﬂ oats on your Ultra

Stick 10cc, make sure to use the parts listed under the

Optional Floats parts.

 RECOMMENDED SERVOS AND ESC

When using the recommended servos and ESC, the

servos may appear to operate slightly slower than

expected. This has been fully tested, and your model will

operate perfectly with this combination. To achieve the

optimum performance from the servos, you can remove

the red wire from the ESC that plugs into the receiver, and

use a separate receiver battery as recommended in the

2-stroke gas parts listing.

 MOTOR, BATTERY AND PROPELLER

COMBINATIONS

We have tested a variety of motor, battery and propeller

combinations. The following are the results of this testing.

• When using a Power 52 motor, 5S 5000mAh battery

and 14 x 8.5E APC propeller, we recommend using a

minimum of a 60A ESC (ELFA1060B).

• When using a Power 52 motor, 6S 5000mAh battery

and 14 x 6E APC propeller, we recommend using a

minimum of a 80A ESC (EFLA1080B).

• When using a Power 52 motor, 5S 5000mAh battery

and 15 x 8E APC propeller, we recommend using a

minimum of a 60A ESC (EFLA1060B).

11

Ultra Stick

™

10cc

 PRÉCAUTIONS D’ASSEMBLAGE

Lors de l’assemblage de votre modèle, nous vous

recommandons de poser les pièces sur une surface

douce comme une serviette douce pour éviter d’abîmer

l’entoilage.

 ÉLIMINATION DES PLIS

L’entoilage de votre modèle peut développer des plis

lors de l’expédition. Vous pouvez les lisser en utilisant le

pistolet à air chaud (HAN100) et le gant (HAN150) ou le

fer à entoiler (HAN101) avec la chaussette de protection

(HAN141). Soyez vigilant sur les zones où plusieurs

couleurs d’entoilage sont superposées, une température

trop élevée pourrait séparer les couleurs. Placez un

chiffon humide et froid sur les couleurs adjacentes pour

éviter leur séparation lorsque vous enlevez les plis.

 PRÉCAUTIONS EN MATIÈRE

D’ENTOILAGE FLUORESCENT

L’entoilage ﬂ uorescent utilisé sur votre modèle peut

décolorer avec le temps en cas d’exposition directe

au soleil. Si possible, nous vous recommandons de

conserver votre modèle à l’abri du soleil pendant les

périodes prolongées.

 TRANSPORT ET STOCKAGE

Lorsque vous transportez ou stockez votre modèle, il

vous faudra un espace d’au moins 2m de longueur et

46cm de hauteur pour accueillir le fuselage. Nous vous

recommandons également l’utilisation d’un sac pour ailes

et de sacs pour stabilisateurs pour les protéger lors du

transport ou stockage. Les guignols et tringleries peuvent

également endommager les gouvernes même dans

les sacs de stockage. Placez toujours les gouvernes de

façon à ce que les parties supérieures soient l’une contre

l’autre pour éviter les contacts et dommages causés par

les guignols ou tringleries.

 INSTALLATION DES FLOTTEURS

FACULTATIFS

Lors de l’installation des ﬂ otteurs recommandés sur

votre UltraStick10cc, assurez-vous d’utiliser les pièces

répertoriées dans la partie Pièces des ﬂ otteurs facultatifs.

 SERVOS ET VARIATEURS ESC

RECOMMANDÉS

Lors de l’utilisation des servos et variateurs ESC

recommandés, les servo peuvent sembler fonctionner

plus lentement que prévu. Tout a été entièrement testé

et votre modèle fonctionnera parfaitement avec cette

combinaison. Pour atteindre les performances optimales

des servos, vous pouvez retirer le ﬁ l rouge du variateur

ESC qui se branche au récepteur, puis utiliser une batterie

de récepteur séparée comme recommandé dans la liste

des pièces à essence deux temps.

 COMBINAISONS MOTEUR, BATTERIE ET

HÉLICE

Nous avons testé plusieurs combinaisons de moteur,

batterie et hélice. Vous trouverez ci-dessous les résultats

de ces tests.

• Avec un moteur Power52, une batterie 5S 5000mAh

et une hélice APC 14 x 8,5E, nous recommandons

d’utiliser au minimum un variateur ESC 60A

(ELFA1060B).

• Avec un moteur Power52, une batterie 6S 5000mAh

et une hélice APC 14 x 6E, nous recommandons

d’utiliser au minimum un variateur ESC 80A

(EFLA1080B).

• Avec un moteur Power52, une batterie 5S 5000mAh

et une hélice APC 15 x 8E, nous recommandons

d’utiliser au minimum un variateur ESC 60A

(EFLA1060B).

 PRECAUZIONI PER LA COSTRUZIONE

Durante l’assemblaggio noi consigliamo di appoggiare

le varie parti su di una superﬁ cie morbida come un

asciugamano di spugna per evitare ammaccature al

rivestimento.

 TOGLIERE LE GRINZE

rivestimento di questo modello potrebbe sviluppare delle

grinze durante la spedizione e quindi per toglierle, sarà

necessario usare una pistola termica (phon) (HAN100) e

un guanto speciale (HAN150), oppure un ferro apposito

per rivestimenti (HAN101) con la sua calza (HAN141).

Bisogna usare cautela quando si lavora attorno ad

aeree con sovrapposizione di colori per evitare la loro

separazione. Evitare di scaldare troppo per non separare

i colori. Mettere un panno umido fresco sui colori vicini,

aiuta a prevenire la separazione dei colori mentre si

tolgono le grinze.

 PRECAUZIONI PER IL RIVESTIMENTO

FLUORESCENTE

Con il tempo, il rivestimento ﬂ uorescente utilizzato sul

modello può sbiadire se esposto direttamente alla luce

solare. Se possibile, si raccomanda di non tenere il

modello alla luce diretta del sole per lunghi periodi.

 TRASPORTO E DEPOSITO

Quando si trasporta o si tiene in magazzino questo

modello, sarà necessario uno spazio di 2 metri di

lunghezza e di 46 centimetri in altezza per adattarsi alle

dimensioni della fusoliera. Si consiglia anche di usare

una custodia per proteggere le ali e lo stabilizzatore. Le

squadrette e i rinvii possono pure causare danni alle

superﬁ ci vicine anche se sono sistemate dentro alle

custodie. Per evitare questo, sistemare le superﬁ ci in

modo da mettere a contatto le loro parti superiori che non

hanno squadrette o rinvii.

 INSTALLAZIONE DEL GALLEGGIANTE

OPZIONALE

Se si installano i galleggianti raccomandati su Ultra Stick

10cc, assicurarsi di utilizzare i componenti elencati nella

tabella relativa ai Galleggianti opzionali.

 SERVO E ESC RACCOMANDATI

Utilizzando i servo e l’ESC raccomandati, la velocità di

funzionamento dei servo potrebbe sembrare inferiore

alle aspettative. I componenti sono stati sottoposti a

test approfonditi e il modello funzionerà perfettamente

con tale combinazione. Per ottenere prestazioni ottimali

dai servo, è possibile rimuovere il cavetto rosso che

collega l’ESC al ricevitore e usare una batteria separata

per il ricevitore come quella consigliata nell’elenco dei

componenti relativi al 2-tempi a benzina.

 COMBINAZIONI MOTORE, BATTERIA ED

ELICA

Sono stati eseguiti test su diverse combinazioni di

motore, batteria ed elica. I risultati dei test sono i

seguenti.

• Se si utilizza un motore Power 52, batteria 5S

5000mAh ed elica APC 14 x 8,5E, si raccomanda l’uso

minimo di un ESC 60A (ELFA1060B).

• Se si utilizza un motore Power 52, batteria 6S

5000mAh ed elica APC 14 x 6E, si raccomanda l’uso

minimo di un ESC 80A (EFLA1080B).

• Se si utilizza un motore Power 52, batteria 5S

5000mAh ed elica APC 15 x 8E, si raccomanda l’uso

minimo di un ESC 60A (EFLA1060B).

12EN

 AILERON AND FLAP INSTALLATION

1. Remove the aileron and ﬂ ap from the wing.

1.

2.

3.

4.

5.

2. Use a 5/64-inch (2mm) drill bit to clear the holes of any

debris for the control horn mounting screws.

3. Use a hobby knife to separate the control horn backplate

from the control horn.

4. Insert the three M2 x 25 machine screws into the holes

of the control horn, then into the holes in the aileron.

Make sure the control horn is installed on the bottom of

the aileron.

5. Slide the control horn backplate on the screws. Apply

a small amount of canopy glue on the screws using a

toothpick, then thread the M2 nuts on the screws. Use

a #1 Phillips screwdriver and 4mm nut driver to tighten

the screws.

 The holes in the control horn backplate are sized

to allow the screw to pass through them. The nuts

must be used to properly secure the control horns

to the control surface. Failure to secure the control

horns with the included nuts will result in the control

horns not being secure on the control surface.

6.

7.

8.

6. Use side cutters to trim the screws.

7. Use a ﬁ le to lightly ﬁ le any sharp points from the screws

after they have been trimmed. Use care not to contact

the control surface with the ﬁ le.

 Prepare and install the flap control horns at this time

following the same procedure as the aileron control horns.

 Make sure to drill the hole for the hinges.

The hole provides a tunnel for the CA to fully

wick into the hinge. Not drilling this hole may

result in hinges that are not properly glued.

8. Remove the hinges from the aileron and ﬂ ap. Use a pin

vise and 1/16-inch (1.5mm) drill bit to drill a hole in the

center of each hinge slot to allow the CA to wick into the

hinge. Drill holes in both the wing and control surfaces

at this time. The ailerons and ﬂ aps can both be prepared

during this step.

9. Place a T-pin in the center of each hinge.

10. Slide the hinges into position in the aileron with the T-pin

resting against the edge of the control surface.

9.

10.

13 EN

Ultra Stick

™

10cc

11.

12.

13.

14.

15.

16.

17.

18.

19.

11. Install all three aileron hinges at this time. 16. Check the gap between the ﬂ ap and aileron. Use a thin

ruler (or similar) that is 1/16-inch (1.5mm) thick as a

spacer so the gap between the ailerons and ﬂ aps are

the same. Remove the T-pins and glue the hinges for the

ﬂ aps using thin CA.

12. Repeat the previous steps to install all three of the ﬂ ap

hinges.

17. Once the CA cures, gently pull on the ﬁ xed surface

and control surface to make sure the hinges are glued

securely. If not, apply additional CA to secure each of the

hinges.

13. Fit the aileron and ﬂ ap to the wing by inserting the

hinges into the slots in the wing.

18. Flex the ﬂ ap and aileron through their range of motion a

few times to break in the hinges.

14. Check that there is a slight gap between the wing and

the end of the aileron. Use a thin ruler (or similar) that is

1/16-inch (1.5mm) thick as a spacer so both the ailerons

have the same size gap. Remove the T-pins from the

aileron hinges.

15. Apply thin CA to the top and bottom of each hinge. Once

the CA cures, gently pull on the ﬁ xed surface and control

surface to make sure the hinges are glued securely. If

not, apply additional CA to secure each of the hinges.

 AILERON AND FLAP SERVO INSTALLATION

19. Remove the aileron servo hatch from the wing. Make

sure to keep the string taped to the wing so it doesn’t fall

into the wing.

14EN

20.

21.

22.

23.

24.

25.

26.

27.

28.

29.

20. Use a hobby knife and #11 blade to remove the covering

in the servo cover to the servo arm.

25. Apply a small amount of thin CA to harden the threads

made in the previous step. Allow the CA to fully cure

before installing the aileron servo cover.

22. Use a toothpick to puncture the covering to locate the

holes for the aileron and ﬂ ap cover screws.

27. Fit the servo between the servo mounting tabs in the

aileron servo tray. The servo arm will be centered in the

slot. Mark the locations for the servo mounting screws

using a pencil, then remove the servo.

21. Check that the servo mount is glued securely to the

servo cover. If the mount is not secure, use a small

amount of medium CA or epoxy to make sure the mount

is securely fastened to the servo cover.

26. Install the grommets and eyelets in the servos. Follow

any instructions included with the servo. Prepare both

ﬂ ap and aileron servos at this time.

23. Use a pin vise and 5/64-inch (2mm) drill bit to drill the

holes in the servo cover mounts.

24. Thread an M3 x 10 self-tapping screw into each of the

holes in the aileron and ﬂ ap servo cover mounting holes.

Remove the screws before proceeding.

 Make sure not to apply excessive downward

pressure which could result in damage to the wing.

28. Use a drill and a 5/64-inch (2mm) drill bit to drill the

holes for the servo mounting screws in the locations

marked in the previous step. Use a 2mm hex wrench to

thread a servo mounting screw into each of the holes in

the aileron servo mounting holes. Remove the screws,

then apply a small amount of thin CA to harden the

threads.

29. Center the aileron servos using the radio system. Prepare

both aileron servos at this time. The output of the servo

arms will mirror each other so the ailerons work in

opposite directions. Use side cutters to remove any

unused arm so they don’t interfere with the operation of

the servo.

15 EN

Ultra Stick

™

10cc

35.

36.

37.

38.

39.

30.

5/8 inch

(16mm)

31.

32.

33.

34.

30. Enlarge the hole in the servo arm that is 5/8-inch

(16mm) from the center of the servo. (Drawing is not to

scale).

 The servo arm length listed is suited for sport flying.

Longer servo arms, such as those included with DUB671,

can be used for more extreme throws and 3D flight.

31. Secure the servo to the cover using a #1 Phillips

screwdriver and the screws provided with the servo.

32. Secure an 9-inch (230mm) servo extension to the

tip servo using a commercially available retainer

(SPMA3054).

33. When building your model with four wing servos (two

ﬂ ap servos, two aileron servos), make sure to orient the

servos as shown.

Optional Two-Servo Wing

34. An optional set of ailerons can be purchased to build

your model without ﬂ aps. When building the aileron-only

version, swap the aileron and ﬂ ap servo covers in the left

wing panel. Use the inner positions for the aileron servos,

and secure the outer servo covers using the steps

outlined in this section of the manual. This allows the use

of a “Y” harness to operate the ailerons.

35. Tie or tape the string located inside the wing to the end

of the servo lead.

36. Retrieve the servo lead at the wing root. Guide the lead

through the hole in the bottom of the wing.

37. Secure the aileron cover in the wing using four M3 x 10

self-tapping screws. Use a #2 Phillips screwdriver to

tighten the screws.

38. Thread an M3 nut on one end of the 100mm pushrod.

Slide a clevis retainer (silicone tubing) on a metal clevis,

then thread the clevis on the rod. Repeat so there are

clevises on both ends of the pushrod. Make the pushrods

for both ailerons and ﬂ aps at this time.

39. Attach the clevis to the hole of the servo arm enlarged

earlier.

16EN

40.

41.

42.

43.

5/8 inch

(16mm)

44.

45.

46.

47.

48.

49.

40. Connect the clevis to the center hole of the control horn.

With the radio on and aileron servo centered, adjust the

link to center the aileron.

41. Once set, slide the clevis retainer (silicone tubing) over

the forks of the clevises, then tighten the nuts against

the clevises. Use threadlock on the nuts to prevent them

from vibrating loose.

42. Center the ﬂ ap servos using the radio system. Prepare

both ﬂ ap servos at this time. The output of the servo

arms will be identical so the ﬂ aps work in the same

directions. Use side cutters to remove any unused arm so

they don’t interfere with the operation of the servo.

43. Enlarge the hole in the servo arm that is 5/8-inch

(16mm) from the center of the servo. (Drawing is not to

scale).

 The servo arm length listed is suited for sport flying.

Longer servo arms, such as those included with DUB671,

can be used for more extreme throws and 3D flight.

44. Install the ﬂ ap servo and assemble the linkage for the

ﬂ ap using the same technique as the aileron linkage. Use

the radio system to set the ﬂ ap to the up position. Adjust

the link so the ﬂ ap is in the up ﬂ ap position.

45. Use the radio system to set the ﬂ ap to the down position.

Use the radio to set the full deﬂ ection position.

 WING INSTALLATION

46. Fit the dowels on the leading edge of the wing into the

holes in the fuselage.

47. Place the wing bolt plate on the wing, then thread the

1/4-20 x 1

3

/

4

-inch nylon wing bolts into the blind nuts in

the fuselage to secure the wing.

Optional

48. The wing bolt plate can be glued directly to the wing.

Use a felt-tipped pen to trace the outline of the wing bolt

plate on the top of the wing.

49. Remove the wing bolts and wing bolt plate. Use a hobby

knife with a new #11 blade to remove the covering 3/32-

inch (2mm) inside the lines drawn on the wing.

17 EN

Ultra Stick

™

10cc

54.

55.

56.

57.

58.

50.

51.

50. Use a paper towel and isopropyl alcohol to remove the

lines from the wing made by the felt-tipped pen.

51. Brush a small amount of 5-minute epoxy on the exposed

wood. Place the wing bolt plate in position and allow the

epoxy to fully cure before proceeding.

 STABILIZER INSTALLATION

 Check the stabilizer mounting surface on the

fuselage to make sure it is flush with the fuselage

sides. If the fuselage sides protrude beyond the

stabilizer mounting surface, then sand them flush.

53. Measure from the tip of the stabilizer to the wing.

Position the stabilizer so both measurements are equal.

54. Check the alignment of the stabilizer to the wing. It

should be equal on both sides of the fuselage.

55. Check all alignments. Mark the outline of the fuselage on

the top of the stabilizer.

56. Use a ruler and carefully cut the covering 1/8 inch (3

mm) inside the line drawn on the stabilizer to remove

the covering from the center of the stabilizer. Remove

the top and bottom covering. Use care not to cut into the

underlying wood, weakening the stabilizer.

57. Use a paper towel and isopropyl alcohol to remove the

lines from the stabilizer. Apply a small amount of thin CA

along the edge of the covering to strengthen the area

under the covering in case the knife has penetrated to

underlying wood.

58. Mix 1/2 ounce (15ml) of 30-minute epoxy. Use an epoxy

brush to apply epoxy to the exposed wood on the top of

the stabilizer.

52. Remove the elevators from the stabilizer. Fit the stabilizer

into the notch in the fuselage. Center the stabilizer.

 Make sure to slide the stabilizer forward

so the elevator joiner wire can be installed.

52.

53.

18EN

59.

60.

61.

62.

63.

64.

65.

66.

67.

68.

59. Use an epoxy brush to apply epoxy to the stabilizer

mounting surface in the notch in the fuselage for the

stabilizer.

60. Fit the stabilizer back into position. Check the alignment

following steps 1 through 3, then use a paper towel and

isopropyl alcohol to remove any excess epoxy from the

fuselage and stabilizer.

61. Use clamps to hold the stabilizer in position. Allow the

epoxy to fully cure before proceeding.

 FIN INSTALLATION

62. Fit the ﬁ n into the slot in the fuselage. Use a ruler to

check the alignment of the ﬁ n to the rear edge of the

fuselage.

63. Use a felt-tipped pen to trace the outline of the ﬁ n on the

top of the fuselage. Also mark the bottom of the ﬁ n along

the fuselage.

64. Use a hobby knife with a #11 blade to carefully remove

the covering 1/8-inch (3mm) inside the lines drawn from

the top of the fuselage at the rear of the ﬁ n.

65. Use a hobby knife with a #11 blade to carefully remove

the covering 1/8-inch (3mm) inside the lines drawn from

the top of the fuselage at the front of the ﬁ n.

66. Use a ruler and carefully cut the covering 1/8 inch (3

mm) below the line drawn on the ﬁ n. Remove the bottom

covering. Use care not to cut into the underlying wood,

weakening the ﬁ n. Apply a small amount of thin CA along

the edge of the covering to strengthen the area under the

covering in case the knife has penetrated to underlying

wood.

67. Mix 1/2 ounce (15ml) of 30-minute epoxy. Use an epoxy

brush to apply the epoxy in the slot for the ﬁ n and to the

exposed wood on the top of the fuselage.

68. Apply epoxy to the exposed wood on the bottom of the

ﬁ n where it comes in contact with the fuselage.

19 EN

Ultra Stick

™

10cc

69.

70.

71.

72.

73.

74.

75.

76.

77.

78.

69. Fit the ﬁ n in position. Check that it is square to the

fuselage.

70. Use tape to hold the ﬁ n in position until the epoxy fully

cures. Check the position of the ﬁ n to make sure it is still

square to the stabilizer while the epoxy is curing.

 ELEVATOR INSTALLATION

71. Remove the elevator joiner wire from the elevators.

Lightly sand the elevator joiner wire where it contacts

the elevators. Use a paper towel and isopropyl alcohol to

remove any oil or debris from the joiner.

72. Fit the joiner wire into the elevator halves. The elevator

joiner wire must be ﬂ ush with the leading edge of the

elevator as shown. Check to make sure the elevator

halves are in alignment with each other.

 Poorly aligned elevators will cause problems

with trimming your model in flight.

73. Place the elevators on a ﬂ at surface. Make sure both

elevators lay ﬂ at on the surface.

74. If the elevators are not in alignment, use pliers to bend

the joiner wire slightly to bring the halves into alignment.

Continue the assembly of your model once the joiner

wire has been correctly checked and adjusted.

75. Use low-tack tape to secure a 2-inch (50mm) wide piece

of clear plastic or waxed paper around the stabilizer

against the fuselage. This will prevent accidentally gluing

the joiner wire and elevators to the stabilizer.

76. Use a pin vise and 1/16-inch (1.5mm) drill bit to drill a

hole in the center of each hinge slot to allow the CA to

wick into the hinge. Drill holes in both the elevators and

stabilizer surfaces at this time. Place a T-pin in the center

of each hinge along side the slot in the hinge. This will

help center the hinge when it is placed in the elevators.

Slide the hinges into position with the T-pin resting

against the edge of the control surface.

77. Partially install the joiner wire into the elevator.

 Fitting the elevator to the stabilizer will require

you to be quick as not to allow the epoxy to cure

that secures the joiner wire. Read through and

practice these steps before mixing any epoxy.

78. Test ﬁ t the elevator to the stabilizer by sliding the hinges

into the slots. The joiner wire will be installed in position

while the hinges are being inserted into the slots.

20EN

84.

85.

86.

87.

88.

79.

80.

81.

82.

83.

79. Check to make sure you can install the hinges and joiner

wire. The leading edge of the elevator will ﬁ t tightly

against the trailing edge of the stabilizer.

80. Mix a small amount of 15-minute epoxy. Use a toothpick

to apply epoxy to the joiner wire.

81. Use a toothpick to apply epoxy to the stabilizer where it

contacts the joiner wire.

82. Fit the elevator back into position. Remove the T-pins

and slide the elevator tightly against the stabilizer. Use a

paper towel and isopropyl alcohol to remove any excess

epoxy before it begins to cure. Use low-tack tape to hold

the elevator tightly against the stabilizer.

 The remaining elevator can be

installed while the epoxy cures.

84. Use a toothpick to apply epoxy to the stabilizer where it

contacts the joiner wire.

85. Fit the remaining elevator into position. Slide it tightly

against the stabilizer, then use low-tack tape to hold it

in position until the epoxy fully cures. Once the epoxy

has cured, remove all tape and clear plastic from the

stabilizer.

 Do not use CA accelerator when gluing hinges. The

CA must be allowed to soak into each hinge to provide the

greatest bond between the hinges and surrounding wood.

86. Remove the T-pins from the hinges. Flex the elevator

slightly, making sure to keep the gap between the

elevator and stabilizer as narrow as possible. Saturate

each of the hinges using thin CA. Apply CA to the top and

bottom of the hinges.

87. Gently pull on the ﬁ xed and moving surface to make sure

the hinges are glued securely. If not, reapply thin CA to

any hinges that are found loose. Flex the control surface

through its range of motion a few times to break-in the

hinges. This will reduce the initial load on the servo when

the surface is ﬁ rst actuated.

 RUDDER AND TAIL WHEEL INSTALLATION

88. Slide the tail wheel bracket on the tail wheel wire. Use a

1.5mm hex wrench to loosen the setscrews in the wheel

collar for the tail wheel. Slide the wheel collar as close to

the tail wheel as possible.

83. Apply epoxy to the exposed joiner wire.

La pagina sta caricando ...

Horizon Hobby HAN2345 Manuale del proprietario

Questo manuale è adatto anche per

Horizon Hobby HAN2345 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti