Hangar 9 HAN2370 Manuale del proprietario

Tiger 30cc

Instruction Manual

Bedienungsanleitung

Manuel d’utilisation

Manuale di Istruzioni

2EN

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon

Hobby, LLC. For up-to-date product literature, visit horizonhobby.com or www.towerhobbies.com and click on the

support or resources tab for this product.

Age Recommendation: Not For Children Under 14 Years. This Is Not A Toy.

SAFETY WARNINGS AND PRECAUTIONS

Read and follow all instructions and safety precautions before use. Improper use can result in ﬁ re, serious injury and

damage to property.

Components

Use only with compatible components. Should any compatibility questions exist, please refer to the product

instructions, component instructions or contact the appropriate Horizon Hobby ofﬁ ce.

Flight

Fly only in open areas to ensure safety. It is recommended ﬂ ying be done at radio control ﬂ ying ﬁ elds. Consult local

ordinances before choosing a ﬂ ying location.

Propeller

Always keep loose items that can become entangled in the propeller away from the prop. This includes loose clothing

or other objects such as pencils and screwdrivers. Keep your hands away from the propeller as injury can occur.

Batteries

Always follow the manufacturer’s instructions when using and disposing of any batteries. Mishandling of Li-Po

batteries can result in ﬁ re causing serious injury and damage.

Small Parts

This kit includes small parts and should not be left unattended near children as choking and serious injury could result.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when

operating this product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,

and serious injury OR create a high probability of superﬁ cial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a

possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or

no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before

operating. Failure to operate the product correctly can result in damage to the product, personal property and

cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic

mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage

to the product or other property. This product is not intended for use by children without direct adult supervision. Do

not attempt disassembly, use with incompatible components or augment product in any way without the approval

of Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to

read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate

correctly and avoid damage or serious injury.

SAFE OPERATING RECOMMENDATIONS

• Inspect your model before every ﬂ ight to ensure it is airworthy.

• Be aware of any other radio frequency user who may present an interference problem.

• Always be courteous and respectful of other users in your selected ﬂ ight area.

• Choose an area clear of obstacles and large enough to safely accomodate your ﬂ ying activity.

• Make sure this area is clear of friends and spectators prior to launching your aircraft.

• Be aware of other activities in the vicinity of your ﬂ ight path that could cause potential conﬂ ict.

• Carefully plan your ﬂ ight path prior to launch.

• Abide by any and all established AMA National Model Aircraft Safety Code.

BEFORE STARTING ASSEMBLY

• Remove parts from bag.

• Inspect fuselage, wing panels, rudder and stabilizer for damage.

• If you ﬁ nd damaged or missing parts, contact your place of purchase.

• Charge transmitter and receiver batteries.

• Center trims and sticks on your transmitter.

• For a computer radio, create a model memory for this particular model.

• Bind your transmitter and receiver, using your radio system’s instructions.

NOTICE: Rebind the radio system once all control throws are set. This will keep the servos from moving to their

endpoints until the transmitter and receiver connect. It will also guarantee the servo reversal settings are saved in the

radio system.

FAA INFORMATION

If you own this product, you may be required to register with the FAA.

For up-to-date information on how to register with the FAA, please visit https://registermyuas.faa.gov/.

For additional assistance on regulations and guidance on UAS usage, visit knowbeforeyouﬂ y.org/.

3 EN

Tiger 30cc ARF

# Required Part # Description

1 DLEG0031 DLE-30cc Gas Rear Carb w/Elec Ig &

1 EFLM4160A Power 160 BL Outrunner Motor, 245Kv

1 EFLM4180A Power 180 BL Outrunner Motor, 195Kv

1 EVOA100 Optical Ignition Kill Switch

1 GPMA1676 Float Set Avistar 30cc/EP Trainer ARF

1 GPMG4795 Rimﬁ re 1.60 63-62-250 Outrunner Brushless

1 HAN237013 Float Mounting Parts Set:Tiger 30cc

2 KXSB50005S30 F-Tek 5000mAh 5S 18.5V 30C, EC5

1 OSMG1533 GT33 Gas Engine

2 SPMX70006S30 7000mah 6S 22.2V Smart 30C; IC5

OPTIONAL PARTS

Part # Description

HAN237001 Fuselage

HAN237002 Wing Set

HAN237003 Tail Set

HAN237004 Cowling

HAN237005 Canopy Top Hatch

HAN237006 Wheel Pants

HAN237007 Wing Tube

HAN237008 Tailwheel Assy

HAN237009 Decal Set

HAN237010 Main Landing Gear

HAN237011 Wheels

HAN237012 Fuel Tank; 14oz

REPLACEMENT PARTSTABLE OF CONTENTS

Notice ......................................................................................................................................................................2

Meaning of Special Language ..................................................................................................................................2

Safety Warnings and Precautions .............................................................................................................................2

Safe Operating Recommendations ...........................................................................................................................2

Before Starting Assembly .........................................................................................................................................2

FAA Information .......................................................................................................................................................2

Replacement Parts ...................................................................................................................................................3

Optional Parts ..........................................................................................................................................................3

Required for Completion, All Power Options ..............................................................................................................4

Required for Completion, Gas Engine Installation......................................................................................................4

Required for Completion, Electric Motor Installation .................................................................................................4

Required Adhesives .................................................................................................................................................4

Tools Required .........................................................................................................................................................4

Removing Wrinkles ..................................................................................................................................................5

Building Precautions ................................................................................................................................................5

Transportation and Storage ......................................................................................................................................5

Replacement Covering .............................................................................................................................................5

Checking Blind Nuts.................................................................................................................................................5

For the Visually Challenged ......................................................................................................................................5

Aileron Servo Installation .........................................................................................................................................5

Flap Servo Installation (Optional) ..............................................................................................................................9

Wing and Stabilizer Installation ..............................................................................................................................10

Elevator Servo Installation ......................................................................................................................................12

Rudder and Fin Installation.....................................................................................................................................14

Rudder Servo Installation .......................................................................................................................................15

Tail Wheel Installation ............................................................................................................................................15

Main Landing Gear Installation ...............................................................................................................................16

Receiver and Receiver Battery Installation..............................................................................................................17

Electric Motor Box Assembly ..................................................................................................................................18

Electric Motor Installation .......................................................................................................................................20

Gas Engine Installation ...........................................................................................................................................22

Fuel Tank Assembly and Installation .......................................................................................................................25

Cowling and Spinner Installation ............................................................................................................................26

Center of Gravity ....................................................................................................................................................28

Control Throws ......................................................................................................................................................28

Preﬂ ight Checklist ..................................................................................................................................................29

Daily Flight Checks ................................................................................................................................................29

Limited Warranty ...................................................................................................................................................29

Warranty and Service Contact Information .............................................................................................................30

Instructions for Disposal of WEEE by Users in the European Union ..........................................................................30

Academy of Model Aeronautics National Model Aircraft Safety Code .......................................................................30

4EN

REQUIRED FOR COMPLETION, GAS ENGINE INSTALLATION

REQUIRED FOR COMPLETION, ALL POWER OPTIONS

REQUIRED FOR COMPLETION, ELECTRIC MOTOR INSTALLATION

# Required Part # Description

1 GPMQ4775 Spinner 3-inch Nylon Aluminum White

4 SPMA3002 Heavy-Duty Servo Extension 9-inch

2 SPMA3004 Heavy-Duty Servo Extension 18-inch

1 SPMAR9350 AR9350 9 Channel AS3X Receiver

# Required Part # Description

1 DUB799 Tygon Gas Tubing,3ft Medium

1 DLEG0435* DLE-35RA Rear Exhaust Gas w/Elec Ig

1 HAN116 Fuel Filler with "T" and Overﬂ ow Fitting

1 MASWM18X10NO1 Master Airscrew 18x10 Maple Propeller

1 SPM9530 Spektrum 3-Wire Switch Harness

2 SPMB2000LPRX 2000mAh 2S 7.4V LiPo Rx Battery

8 SPMSA6380 A6380 H-T/H-S Digital HV Servo

# Required Part # Description

1 APC18010E Electric Propeller, 18 x 10E

1 SPMXCA506 IC5 Battery Series Harness 4-inch 10AW

1 CSE010013100 Talon HV120 ESC 010-0131-00

1 GPMG4796 Rimﬁ re 1.70 63-62-200 Outrunner

7 SPMSA6380 A6380 H-T/H-S Digital HV Servo

2 SPMX50006S30 5000mah 6S 22.2V Smart 30C; IC5

TOOLS REQUIRED

Description

Box or open end wrench: 10mm, 7/16-inch, 1/2-inch

Clamps

Covering iron

Cutoff wheel for rotary tool

Drill

Drill bit set, metric and english

Epoxy brushes

Felt-tipped pen

Flat blade screwdriver

Flat ﬁ le

Flux paste

Heat gun

Hemostats

Hex wrench set, metric and english

Hobby knife with #11 blade

Hobby scissors

Hobby square

Hook and loop tape

Light machine oil

Low tack tape

Medium grit sandpaper

Mixing cups

Mixing sticks

Pencil

Phillips screwdriver #1, #2

Pin vise

Pliers

Razor saw

Rotary tool

Ruler

Sanding drum for rotary tool

Scissors

Side cutter

Silver solder

Stepped reamer

Toothpicks

Torch or soldering iron

Vise grips

Wire cutter

REQUIRED ADHESIVES

Description

15-minute epoxy

30-minute epoxy

Thin CA

Medium CA

Threadlock, low and high strength

* Use of the DLE-35RA Rear Exhaust engine may require up to 12 ounces (340g) of additional nose weight to properly

balance this model.

1. Use a hobby knife with a #11 blade to remove the covering on the

top of the wing near the wing root for the servo leads.

5. Prepare both the left and right aileron servos.

3. Install the grommets and eyelets in the servos. Follow any

instructions included with the servo.

2. Use a hobby knife with a #11 blade to remove the covering on the

bottom of the wing for the servo opening.

4. Center the aileron servo using the radio system. Place a servo arm

on the aileron servo perpendicular to the servo centerline. Use side

cutters to remove and arms that may interfere with the operation of

the servo.

AILERON SERVO INSTALLATION

5 EN

Tiger 30cc ARF

REMOVING WRINKLES

The covering of your model may develop wrinkles during shipping. Use a covering iron (HAN101) with a sealing iron

sock (HAN141) to remove them. Start with a lower heat setting and use caution while working around areas where

the colors overlap to prevent separating the colors. It is also advised to use caution around the canopy as it is plastic

and could distort with excessive heat. Avoid using too much heat, which could also separate the colors. Placing a cool

damp cloth on adjacent colors will also help prevent the separation of the colors while removing wrinkles. Only use a

heat gun (HAN100) once the covering iron has been used.

BUILDING PRECAUTIONS

Prepare the work surface prior to beginning the build. The surface should be soft and free of any sharp objects. We

recommend resting the airframe parts on a soft towel or pit mat to prevent scratching or denting the surface of the

aircraft.

TRANSPORTATION AND STORAGE

When transporting and storing your model, you will need a minimum of 80 inches (2.1m) in length, and 19 inches

(50cm) in height to accommodate the size of the fuselage. We also recommend the use of wing and stabilizer bags to

help protect these surfaces during transport and storage. The control horns and linkages can cause damage to other

surfaces even when placed in storage bags. Always transport and store the wings and stabilizer so the linkages do not

contact other panels to prevent damage.

REPLACEMENT COVERING

Your model is covered with MonoKote® ﬁ lm in the following colors. If repairs are required, order these coverings to

make those repairs.

TOPQ0201 Red

TOPQ0204 White

TOPQ0226 Sapphire Blue

TOPQ0205 Aluminum

CHECKING BLIND NUTS

When building the aircraft, you will be required to thread machine screws into blind nuts. We recommend pre-threading

the screws to make sure the blind nuts are clear of any debris. If the screws do not thread in easily, clear the threads

using the appropriate tap and tap handle.

FOR THE VISUALLY CHALLENGED

A copy of this manual can be found at www.horizonhobby.com under the tab for this particular model. Feel free to

download this manual and use a PDF viewer to zoom in on any text or images that may be in question when building

from the printed manual.

6. Secure an 18-inch (460mm) servo extension to the servo using a

commercially available retainer (SPMA3054).

 The length of the extension may vary depending on servo selection.

The extension listed is uitable for the recommended servos.

7. Tie or tape the string located inside the wing to the end of the servo

lead.

9. Route the servo lead through the hole in the top of the wing.

10. Fit the servo in the wing with the servo output toward the leading

edge. Mark the locations for the servo mounting screws using a

pencil, then remove the servo.

8. Use the string to pull the servo lead through the wing and out at the

root.

 We left a small amount of the string on the aileron

servo lead so it can be quickly differentiated between

the flap servo lead that will be installed later.

11. Use a pin vise and a 5/64-inch (2mm) drill bit to drill the holes for

the servo mounting screws in the locations marked in the previous

step.

 If using a drill, make sure not to drill through

the covering on the top of the wing.

12. Thread a servo mounting screw into each of the holes in the servo

mounting holes.

14. After the CA has fully cured, secure the servo to the cover using the

screws provided with the servo.

15. When mounting the aileron servos, the servo arms will face toward

the wing tips on each wing panel.

 Installing the aileron servos facing the opposite direction

allows their connection to the receiver using a Y-Harness.

13. Remove the screws, then apply a small amount of thin CA to harden

the threads made in the previous step.

6EN

16. Use low-tack tape to hold the aileron/ﬂ ap centered when installing

the linkage.

17. Slide a retainer over the barrel of the clevises.

 There are an equal number of threaded clevises

and solder clevises. Make sure to sort the clevises

so they can be used in the correct locations.

19. When attaching the clevis to the servo arm, use the hole that is 5/8

in (16mm) from the center of the servo horn.

20. Attach the clevis to the aileron servo arm.

18. Thread a 4-40 nut on the threaded end of a short pushrod. Thread

the clevis on the pushrod until the end of the pushrod is visible

between the forks of the clevis.

21. Hold the pushrod perpendicular to the hinge line. Mark the aileron

where the pushrod crosses onto the aileron using a felt-tipped pen.

22. Position the control horn centered on the mark made in the previous

step. The holes for the clevis in the control horn will align with the

hinge line.

 There is a hardwood plate in the ailerons that the

control horns will be mounted to. Make sure the

control horn is positioned over this plate.

24. Wrap a piece of low-tack tape 3/8 inch (9.5mm) from the end of

a 5/64-inch (2mm) drill bit. This will act a stop to prevent drilling

through the aileron.

25. Use a drill and the drill bit from the previous step to drill the holes for

the control horn mounting screws.

 Do not drill through the top surface of the aileron.

23. Use a felt-tipped pen to mark the mounting locations for the control

horn screws.

7 EN

Tiger 30cc ARF

5/8 inch

(16mm)

26. Use a #1 Phillips screwdriver to thread a #4 x 1/2 inch sheet metal

screw into each of the holes. Remove the screws before proceeding.

 It is important to prepare and harden the surrounding wood

when mounting the control horns. Failure to do so may result

in the control horns not being as secure as necessary.

27. Place 2-3 drops of thin CA in each of the holes. Allow the CA to fully

cure before proceeding.

29. Attach a solder-type clevis to the center hole of the aileron control

horn.

30. Hold the pushrod against the clevis. Use a felt-tipped pen to mark

the edge of the clevis on the pushrod.

28. Mount the control horn to the aileron using four #4 x 1/2 inch sheet

metal screws. Tighten the screws using a #1 Phillips screwdriver.

31. Remove the pushrod from the servo. Use side cutters to trim the

pushrod 3/8 inch (9.5mm) past the mark made in the previous step.

This will be inserted into the solder clevis.

32. Use medium grit sandpaper to lightly scuff the pushrod. Use a paper

towel and isopropyl alcohol to remove any debris or oils from the

pushrod.

 If the mark is removed, make sure to replace it on the pushrod.

33. Apply a small amount of ﬂ ux paste to the pushrod. This will help

draw the solder along the pushrod wire and into the clevis.

34. Hold the pushrod and clevis using pliers or hemostats. Use a torch or

soldering iron to heat the clevis and wire. Use silver solder to secure

the clevis to the pushrod wire.

 Align the clevis with the mark on the pushrod wire

to achieve the correct length of the pushrod.

 Once the solder has cooled, pull hard on the pushrod wire

and clevis to make sure it has been soldered securely

in place. Failure to correctly solder the clevises can

result in pushrod failure and the loss of the model.

 Use silver solder when assembling the pushrod.

8EN

35. Remove the nut and clevis from the threaded end of the pushrod.

Slide a retainer on the pushrod wire and over the barrel of the solder

clevis.

36. Attach the solder clevis to the control horn. Slide the retainer over

the forks of the clevis to secure it to the control horn.

37. Thread the nut and threaded clevis back into place on the pushrod.

Attach the threaded clevis to the servo arm. Make sure to adjust

the clevis to center the aileron when the servo is centered. Apply

a drop of threadlock on the threads of the pushrod near the clevis.

Thread the nut over the threadlock and against the clevis. Use pliers

to tighten the nut against the clevis, then slide the retainer over the

forks of the clevis.

 Operational flaps are optional on this model. They can

be added at any time during the life of the model.

1. Use a razor saw to cut the two dowels connecting the ﬂ ap and

aileron.

 There is a gap between the flap and aileron

where these dowels are located.

2. Use medium grit sandpaper to sand the dowels smooth with the

face of the aileron and ﬂ ap.

 If the covering becomes damaged, use a covering iron

and white covering to replace any damaged covering.

4. Install the ﬂ ap servos in the wing. The procedure is the same as the

aileron servos. When installing the ﬂ ap servos, the servo arm on

both servos will face toward the left wingtip.

 Installing the flap servos facing the same direction allows

their connection to the receiver using a Y-Harness.

5. Prepare the pushrod for the ﬂ aps. This is the same procedure as the

pushrod for the aileron. When attaching the clevis to the servo arm,

use the hole that is 5/8 in (16mm) from the center of the servo horn.

3. Prepare the two ﬂ ap servos.

FLAP SERVO INSTALLATION (OPTIONAL)

9 EN

Tiger 30cc ARF

5/8 inch

(16mm)

6. Install the control horn and complete the pushrod. These steps are

the same as the aileron control horn and pushrod steps.

7. Route the lead for the ﬂ ap servo through the wing and out the hole

in the top of the wing.

 The wing must be installed before the stabilizer, as it is essential to

align the stabilizer with the wing for the aircraft to perform properly.

1. Test ﬁ t the dowel into the leading edge of the wing. The dowel will

protrude 1/2 inch (13mm) from the wing. Remove the dowel and mix

a small amount of 5-minute epoxy. Use a toothpick to apply epoxy

inside the hole.

 There are two larger diameter dowels, and one smaller

diameter dowel. The two larger diameter dowels are

used at the leading edge, and the smaller diameter

dowel at the trailing edge as an alignment pin.

2. Apply epoxy to the portion of the dowel that ﬁ ts into the wing. Slide

the dowel into position, and remove any excess epoxy using a paper

towel and isopropyl alcohol.

 The remaining wing dowel can be installed at this time.

3. Use a pencil to mark a centerline on the smaller diameter dowel.

4. Use epoxy to glue the dowel into the wing near the trailing edge.

Insert the dowel up to the line made in the previous step. Remove

any excess epoxy using a paper towel and isopropyl alcohol.

WING AND STABILIZER INSTALLATION

10EN

5. Slide the wing tube into the wing tube socket.

 The wing tube may be a tight fit in the socket. Polishing

the wing tube with fine sand paper or steel wool will

help ease the installation of the wing tube.

6. Slide the wing panels together. There should be no gap between the

panels.

7. Slide the canopy hatch forward to release the tab at the rear near

the top of the fuselage. Lift the canopy hatch from the fuselage and

set it aside.

 Pilot shown is optional and not included with the model.

8. Use a hobby knife and #11 blade to remove the covering from the

slot at the rear of the fuselage for the stabilizer.

9. Use a hobby knife and #11 blade to remove the covering at the rear

of the fuselage. Remove the tail post from the fuselage.

 The tail post is left in position at the factory to prevent damage

and maintain the structural integrity of the fuselage during

shipping and must be removed to install the stabilizer.

10. Slide the wing into position, guiding the dowels in the wing into the

holes in the fuselage. Make sure the leads from the ailerons (and

ﬂ aps) are inside the fuselage.

11. Secure the wing to the fuselage using the two 1/4-20 x 2 inch nylon

bolts. Use a ﬂ at screwdriver to tighten the bolts, securing the wing.

12. Place the stabilizer in position. Make sure to slide the stabilizer

as far forward in the fuselage as possible. Use a hobby knife and

#11 blade to remove the covering between the slot for the ﬁ n and

the opening for the tab on the ﬁ n. Use care to only cut through the

covering as not to damage the underlying structure.

 Use low heat on your covering iron to seal the edges of the

covering. High heat may result in the covering pulling back

and exposing bare balsa when the fin is glued in place.

13. Fit the ﬁ n into position. The ﬁ n will help in aligning the stabilizer to

the fuselage, as it keys into both items.

14. Stand back 8-10 feet (2-3 meters) and check that the stabilizer

is aligned with the wing. Lightly sand the stabilizer saddle on the

fuselage to correct any misalignment.

11 EN

Tiger 30cc ARF

AA

A=A

15. Measure from each wing tip to each stabilizer tip. Adjust the

stabilizer so the measurements are the same for both sides.

16. Place two T-pins into the stabilizer on both sides of the fuselage.

These will help return the stabilizer to the correct position in the

fuselage.

18. Use an epoxy brush to apply epoxy to the exposed wood in the

stabilizer slot of the fuselage.

19. Slide the stabilizer into position. Check the alignment to verify it

is correctly positioned. Use a paper towel and isopropyl alcohol to

remove any epoxy from the fuselage and stabilizer. Allow the epoxy

to fully cure before proceeding.

 Regularly check the stab alignment while the epoxy is curing to

make sure it does not move and sets in a misaligned angle.

17. Remove the ﬁ n and stabilizer from the fuselage. Mix 1 ounce (30ml)

of 30-minute epoxy and use an epoxy brush to apply it to the

exposed wood on the top and bottom of the stabilizer.

1. Prepare both elevator servos by installing the grommets and eyelets.

Do not install the screw that secures the servo arm to the servo.

2. Mount an elevator servo in the fuselage with the output facing the

front of the fuselage. The steps for mounting servos are the same as

in the section for the aileron servo installation.

3. Prepare the clevis by sliding a retainer on the barrel of the clevis.

Thread a 4-40 nut, then the clevis, on the threaded end of a long

pushrod. Attach the clevis to the elevator control horn.

4. Use a stiff ruler and two clamps to hold the elevator in position while

installing the elevator control horn and elevator pushrod.

5. Slide the pushrod into the pushrod tube in the fuselage. Make sure

to use the hole closest the stabilizer on the side where both the

rudder and elevator pushrods exit.

ELEVATOR SERVO INSTALLATION

12EN

AA

A=A

6. Position the control horn so the holes in the control horn align

with the hinge line. The pushrod will cause the control horn to fall

naturally on the elevator. Mark the location for the control horn

mounting screws on the elevator.

7. Move the control horn away from the elevator. Use a pin vise and

7/64-inch (2.5mm) drill bit to drill the holes for the control horn

mounting screws. Use care to drill the holes straight and parallel in

the elevator.

 Unlike the aileron control horns, the elevator control

horns use a backplate on the opposite side of the

control surface. Failure to fit this backplate will result

in control failure and possible loss of the model.

9. The socket head cap screws will thread into the control horn back

plate. Use a 3/32-inch hex wrench to tighten all four screws.

 Do not over-tighten the screws and damage the

underlying structure of the elevator.

10. When attaching the clevis to the servo arm, use the hole that is 5/8

in (16mm) from the center of the servo horn.

8. Use four 4-40 x 3/4 inch socket head cap screws to attach the

control horn to the elevator.

11. Attach a solder-type clevis to the elevator servo arm. Hold the

pushrod against the clevis. Use a felt-tipped pen to mark the edge of

the clevis on the pushrod.

12. Remove the pushrod from the fuselage. Remove the clevis from the

elevator servo arm. Cut the pushrod and solder the clevis on the

pushrod using the technique outlined for the aileron pushrods.

 Once the solder has cooled, pull hard on the pushrod wire

and clevis to make sure it has been soldered securely

in place. Failure to correctly solder the clevises can

result in pushrod failure and the loss of the model.

14. Install the remaining control horn on the opposite elevator.

13. Reinstall the pushrod and connect it to the servo arm and control

horn. With the radio system on and elevator servo centered, adjust

the clevis to center the elevator. Use threadlock near the threaded

clevis, then tighten the nut against the clevis to secure the clevis.

Slide all retainers over the forks of the clevises to complete the

pushrod installation.

13 EN

Tiger 30cc ARF

5/8 inch

(16mm)

15. Complete the pushrod installation for the remaining elevator. Once

complete, make sure to install the screws that secure the servo

arms in the servos. Turn off the radio system.

1. Fit the ﬁ n in position. Use a hobby square to make sure the ﬁ n is

square to the stabilizer. If not, lightly sand the ﬁ n where it ﬁ ts into

the stabilizer and fuselage to correct the alignment.

3. Apply epoxy to the exposed wood inside the rear of the fuselage.

4. Apply epoxy to the exposed wood on the ﬁ n where it will contact the

fuselage. Also apply epoxy under the ﬁ n to glue it to the top of the

fuselage where the covering was removed.

2. Remove the ﬁ n from the fuselage. Mix 1 ounce (30ml) of 30-minute

epoxy and use an epoxy brush to apply it to the exposed wood in the

stabilizer.

5. Fit the ﬁ n into position and check the alignment. Use low-tack tape

to hold the ﬁ n in position until the epoxy fully cures. Continually

check the ﬁ n to make sure it remains aligned with the stabilizer as

the epoxy cures.

RUDDER AND FIN INSTALLATION

14EN

1. Prepare the rudder pushrod and install the rudder control horn

following the procedure outlined for the elevator control horn.

 Unlike the aileron control horns, the rudder control

horn uses a backplate on the opposite side of the

control surface. Failure to fit this backplate will result

in control failure and possible loss of the model.

2. When attaching the clevis to the rudder servo horn, use the hole that

is 5/8 inch (16mm) from the center of the servo arm.

4. Install the rudder servo in the fuselage with the servo output facing

the rear of the aircraft. Align the rudder pushrod with the hole in the

arm the clevis will be attached. Mount the servo following the same

procedure as the aileron and elevator servos.

5. Prepare and secure the clevis for the rudder pushrod that completes

the rudder pushrod. The steps are outlined in the aileron servo

pushrod installation.

3. Center the rudder servo using the radio system. Install the servo arm

on the servo perpendicular to the servo centerline. Use side cutters

to remove any arms that may interfere with the operation of the

servo,

1. Mark the bottom of the rudder 1

1

/

2

and 2

1

/

2

inches (38mm and

63mm) back from the rudder hinge line.

2. Use a rotary tool and cut-off wheel to make a slot that is centered on

the bottom of the rudder between the two marks. Use a hobby knife

with a #11 blade to carefully trim the slot until the tail wheel bushing

ﬁ ts into the slot, ﬂ ush with the bottom of the rudder.

4. Guide the tiller arm from the tail wheel assembly through the

bushing. The bracket will rest ﬂ at on the fuselage. If not, carefully

bend the tiller arm until the bracket rests ﬂ at on the fuselage. The

vertical hole in the bracket will align with the rudder hinge line.

5. Center the bracket on the fuselage and use a felt-tipped pen to mark

the positions for the three mounting screws on the bottom of the

fuselage.

3. Mix a small amount of 5-minute epoxy and use it to glue the tail

wheel bushing in the rudder. Make sure to apply epoxy in the

slot and to the bushing. Remove any excess epoxy using a paper

towel and isopropyl alcohol. Allow the epoxy to fully cure before

proceeding.

RUDDER SERVO INSTALLATION TAIL WHEEL INSTALLATION

15 EN

Tiger 30cc ARF

5/8 inch

(16mm)

6. Remove the bracket. Use a drill and 5/64-inch (2mm) drill bit to

drill the holes for the mounting screws. Make sure to prepare the

holes by threading a #4 x 1/2 inch sheet metal screw into each hole.

Remove the screw and apply two to three drops on thin CA in each

hole. Allow the CA to fully cure before proceeding.

7. Attach the tail wheel bracket to the fuselage using three #4 washers

and three #4 x 1/2 inch sheet metal screws. Tighten the screws

using a #1 Phillips screwdriver.

8. Slide the wheel collar against the bracket. Use a .050” hex wrench

to tighten the setscrew in the wheel collar.

9. Use a ﬂ at ﬁ le to make a 1/4 inch wide ﬂ at area on the tail gear wire.

1. Use a hobby knife and #11 blade to remove the covering from the

bottom of the fuselage for the landing gear mounting screws.

2. Use a rotary tool with a cut-off wheel to trim the axle to a length of

1

5

/

8

inches (41mm).

4. Attach the axle to the landing gear using the axle nut. Use 7/16 inch

and 1/2 inch wrench to tighten the nut, securing the axle. Make sure

the ﬂ at areas face toward the bottom of the landing gear.

5. Slide a wheel collar on the axle. Place a drop of threadlock on a

6-32 x 3/4 inch socket head cap screw. Use the screw to secure the

wheel collar against the nut on the axle. Use a 7/64 inch hex wrench

to tighten the screw on the ﬂ at areas on the axle.

3. Use a ﬂ at ﬁ le to make a 1/4 inch (6mm) wide ﬂ at area at the end of

the axle. Make a second 1/4 inch (6mm) wide ﬂ at area against the

nut on the axle.

10. Secure the tail wheel to the wire using a wheel collar. Tighten the

setscrew on the ﬂ at area using a .050” hex wrench.

MAIN LANDING GEAR INSTALLATION

16EN

1. Install the receiver in the fuselage. Mount any remote receivers in

the fuselage using hook and loop tape.

 Apply a small amount of 5-minute epoxy to the hook

and loop tape to secure it to the radio tray.

2. Secure the receiver battery in the fuselage. The battery location can

be changed to help in adjusting the Center of Gravity.

3. Remove the covering for the switch using a hobby knife with a

#11 blade. Use the opening that best ﬁ ts the switch for your radio

system. Secure the switch in the side of the fuselage.

6. Apply a drop of light machine oil on the axle.

7. Slide the wheel on the axle. Secure the wheel using a wheel

collar and 6-32 x 1/4 inch socket head cap screw. Place a drop of

threadlock on the threads of the screw before tightening it using a

7/64 inch hex wrench.

8. Attach the landing gear to the fuselage using four 6-32 x 3/4 inch

socket head cap screws, four #6 washers and four #6 lock washers.

Apply a drop on the threads of each screw before threading them

through the landing gear and into the blind nuts. Tighten the screws

using a 7/64 inch hex wrench.

 The landing gear will angle forward slightly when installed.

9. Attach the wheel pants to the landing gear using two 4-40 x 1/2 inch

machine screws and two #4 washers. Apply a drop of threadlock on

the threads of each screw before tightening them using a #1 Phillips

screwdriver.

RECEIVER AND RECEIVER BATTERY INSTALLATION

17 EN

Tiger 30cc ARF

5. A second set of sides, as well as top and bottom pieces will ﬁ t over

those previously installed.

 Once the fit of the pieces has been checked, disassemble

the motor box and sort the pieces so they can be quickly

identified when assembling the motor box using epoxy.

STEP 1

 We highly recommend using an epoxy with a cure time of at least

30 minutes or longer when assembling the motor box to allow

enough time to fully assemble it before the epoxy begins to cure.

6. Mix 1/2 ounces (15mL) of 30-minute epoxy. Use an epoxy brush to

apply epoxy to one side of the end plates.

7. Stack a second end plate on the ﬁ rst, then apply epoxy to the plate.

Stack the third end plate. There will be epoxy between each of the

three end plates.

 Assemble the motor box without mixing any epoxy first

to fully understand the fit of the components. Once epoxy

has been mixed, there will be a limited amount of time to

build the motor box before the epoxy begins to cure.

 The motor box will be built in three steps. This

will allow time to assemble the motor box.

1. Locate the four end plates for the motor box. Three will be used for

the motor mounting, and one will be used when mounting the motor

box to the ﬁ rewall.

2. Fit the three end plate in the wide slot in the motor box top/bottom.

The single end plate ﬁ ts in the narrow slot.

 The top/bottom has tabs along the sides.

3. Fit the motor box top/bottom on the end plates.

4. The motor box sides can then be ﬁ t to the assembly.

 The sides have notches that the tabs on the top/bottom will key into.

8. Apply epoxy to the area on the side plate where the end plates will

be in contact with the side plate. Position the end plates (previous

step and single plate) on the side plate. Continue working until the

motor box has the ﬁ rst set of side plates and top/ bottom plates in

position.

9. Use low-tack tape to hold the motor box together until the epoxy

cures. Use a paper towel and isopropyl alcohol to remove any

excess epoxy.

 It is critical to remove all excess epoxy or the

remaining pieces will not fit into position.

ELECTRIC MOTOR BOX ASSEMBLY

18EN

STEP 2

10. Mix 1/2 ounces (15mL) of 30-minute epoxy. Use an epoxy brush to

apply epoxy to one of the top/bottom plates. Apply epoxy to the top/

bottom plate.

11. Place a second top/bottom plate in position. Repeat until the second

set of side plates and top/bottom plates have been positioned.

STEP 3

13. Mix 1/2 ounces (15mL) of 30-minute epoxy. Apply epoxy to a single

square end plate.

14. Place the square end plate in position. Repeat for the ﬁ nal square

end plate.

12. Use low-tack tape to hold the motor box together until the epoxy

cures. Use a paper towel and isopropyl alcohol to remove any

excess epoxy.

 It is critical to remove all excess epoxy or the

remaining pieces will not fit into position.

15. Use low-tack tape to hold the motor box together until the epoxy

cures. Use a paper towel and isopropyl alcohol to remove any excess

epoxy. Allow the epoxy to fully cure before proceeding.

 Use medium grit sandpaper to sand the motor

box if necessary for a finished took.

19 EN

Tiger 30cc ARF

1. Measure and mark the locations for the motor box mounting screws

on the ﬁ rewall.

 These measurements are used when mounting the included

motor box to the firewall. Using a different motor or motor box

may require different measurements. Check the alignment of the

motor mor motor box after marking the firewall for alignment.

2. Use a drill and 7/32-inch (5.5mm) drill bit to drill the holes from the

previous step.

 Drill a 1/8-inch (3mm) pilot hole first to prevent the larger

drill bit from wandering when drilling the final holes.

4. Attach the motor box to the ﬁ rewall using the four 8-32 x 3/4 inch

socket head cap screws and four #8 washers. Tighten the screws

using a 9/64 inch hex wrench.

3. Use an 8-32 x 3/4 inch socket head cap screw and #8 washer to

pull the 8-32 blind nuts into the back of the ﬁ rewall from inside the

fuselage. Use a 9/64 inch hex wrench for the screws. Remove the

screws once all blind nuts have been installed.

5. Attach the motor to the motor box using four 8-32 blind nuts, four #8

washers, four #8 lock washers and four 8-32 x 3/4 inch socket head

cap screws.

 Use a 7/32-inch (5.5mm) drill bit to clear any epoxy from

the mounting holes. Drilling slightly larger mounting holes

will allow for any alignment when using different motors.

 The Tiger 30cc has been designed to use a variety of power

systems. Please make sure to check the power system selected

has mounting holes that align with holes in the motor box. New

holes may be required dependant on the motor selection.

8. Remove the motor and motor box from the ﬁ rewall. Mix 1/4 ounce

(8mL) of 5-minute epoxy. Slide the ﬁ rewall so epoxy can be applied

in the ﬁ nal locations for the ﬁ rewall.

6. Position the ﬁ rewall so the distance shown measures between

7

1

/

4

–7

3

/

4

inches (184mm–196mm). This measurement may vary

depending on motor selection. Verify the measurement is within this

range when the motor has been attached to the ﬁ rewall.

7. Use a pencil to mark the location of the ﬁ rewall on the fuselage

sides and top.

ELECTRIC MOTOR INSTALLATION

20EN

1 inch

(25mm)

1 inch

(25mm)

1 inch

(25mm)

1 inch

(25mm)

La pagina sta caricando ...

Hangar 9 HAN2370 Manuale del proprietario

Hangar 9 HAN2370 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti