Vinten Vector 75 Operator Guide

Operators Guide

V4095-4980/2

Vector 75 Pan and Tilt Head

CN

JP

V4095-0001

Vector 75

Pan and Tilt Head

Publication Part No. V4095-4980 Issue 2

English . . . . . . . . . . . . . . . . . . . . . Page 3

Deutsch . . . . . . . . . . . . . . . . . . . Seite 17

Español . . . . . . . . . . . . . . . . . .Página 33

Français . . . . . . . . . . . . . . . . . . . Page 49

Italiano . . . . . . . . . . . . . . . . . . .Pagina 65

Português . . . . . . . . . . . . . . . .Página 81

日本語 . . . . . . . . . . . ページ 97

中文 . . . . . . . . . . . . .页码 119

document may be stored in a retrieval system, transmitted,

copied or reproduced in any way, including, but not limited

to, photocopy, photograph, magnetic or other record

without the prior agreement and permission in writing of

the Vitec Group plc.

Trademarks

Vinten™, Vector

®

and Quickfix

®

are registered trademarks

of the Vitec Group plc.

Disclaimer

Information contained within this document is subject to

change. Camera Dynamics Limited reserves the right,

without notice, to make changes in equipment design or

performance as progress in engineering, manufacturing or

technology may warrant.

Published by

Vitec Group Videocom Division

Technical Publications Department

William Vinten Building

Western Way

Bury St Edmunds

Suffolk IP33 3TB

United Kingdom

Email: [email protected]

English

3

Contents

Page

Safety – read this first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Warning symbols in this Operators Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Usage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Caring for the environment by recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Technical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Introduction and description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Perfect Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Pan and tilt drag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Pan and tilt brakes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Illuminated level bubble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Pan bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Camera mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Mounting the head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Pan bars. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Fitting a camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Balancing the head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Locking the platform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Pan and tilt brakes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Pan and tilt drag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Cleaning balance mechanism tracks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Routine maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Replacing the battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Adjusting the slide plate clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Repositioning the wedge adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Adjusting the pan and tilt brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

English

4

Safety – read this first

Warning symbols in this Operators Guide

WARNING

Where there is a risk of personal injury or injury to others, comments appear

highlighted by the word ‘WARNING’—supported by the warning triangle symbol.

Where there is a risk of damage to the product, associated equipment, process or

surroundings, comments appear highlighted by the word ‘CAUTION’.

FINGER TRAP

Where there is a risk of trapping fingers within parts of the product or other

equipment mounted to the product, comments appear supported by the finger trap

symbol.

Usage

The Vector 75 pan and tilt head is designed for use in broadcast and film studios to support and

balance a camera and ancillary equipment weighing up to 75 kg (165.3 lb), and must be mounted

on equipment designed to support a minimum payload of 95 kg (209 lb).

The Vector 75 pan and tilt head is intended for use by professional TV broadcast and film

camera operators.

Caring for the environment by recycling

Disposal of waste batteries

Any batteries included with this product must not be treated as household waste. By ensuring

these batteries are disposed of correctly, you will help prevent potentially negative consequences

for the environment and human health, and help conserve natural resources. Hand the battery

over to the applicable collection point for recycling waste batteries.

WARNING!

1. Do NOT attempt to use this product if you do not fully understand how

to operate it.

2. Do NOT use this product for any other purpose than that specified in

the Usage statement.

3. Refer all maintenance beyond that detailed in this Operators Guide to

an authorised Vinten service centre.

CAUTION

finger trap

English

5

Technical specification

Maximum payload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 kg (165.3 lb)

Payload Centre of Gravity height range. . . . . . . . . . . . . . . . . . . . . . . . . . 80–250 mm (3–10 in.)

Weight (complete with pan bar and wedge adaptor) . . . . . . . . . . . . . . . . . . . .19.15 kg (42.2 lb)

Overall dimensions:

Height (with wedge adaptor)

Minimum balance setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255 mm (10.0 in.)

Maximum balance setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .355 mm (14.0 in.)

Length (without pan bar) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .355 mm (14.0 in.)

Width (without pan bar) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .350 mm (13.8 in.)

Width (with two pan bars). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .445 mm (17.5 in.)

Tilt range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±52

Pan range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360

Counterbalance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . fully variable Perfect Balance system

Level bubble. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . illuminated, high contrast blue LED

Level bubble illumination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 seconds (timeout)

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PP3 (9V)

Tripod fixing . . . . . . . . . . . . . . . . . . . . . . . . Four-bolt flat base with Quickfix

®

groove (standard)

English

6

Vector 75

Pan and Tilt Head, left side

(Fig. 1)

[1] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Wedge adaptor

[2] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wedge adaptor lever

[3] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wedge adaptor securing screw

[4] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pan brake lever

[5] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tilt brake lever

[6] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Carrying handle

[7] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Level bubble illumination switch

[8] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Level bubble

[9] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pan drag adjustment knob

[10] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pan bar clamp

[11] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tilt drag adjustment knob

[12] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Slide plate clamp

[13] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Slide plate adjustment knob (retractable ‘T’ bar)

Vector 75

Pan and Tilt Head, right side

(Fig. 2)

[14] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Slide plate

[15] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Perfect Balance adjustment knob

[16] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Centre lock button

[17] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Centre lock release catch

[18] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pan bar mount

Vector 75

Pan and Tilt Head, underside

(Fig. 3)

[19] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bolt fixing hole

[20] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bolt-hole position indicator

English

7

Introduction and description

The Vector 75 pan and tilt head embodies a unique linkage counterbalancing mechanism,

patented Vinten lubricated friction (LF) drag assemblies for pan and tilt motions and an

adjustable camera mounting plate.

Perfect Balance

The balance system is easily adjusted by a knob [15] on the right side of the head. The Perfect

Balance adjustment control compensates for differing platform load/C of G heights by varying

the mechanical advantage of a bell-crank in the counterbalance mechanism.

Pan and tilt drag

Both the pan and tilt mechanisms incorporate lubricated friction (LF) drag systems to ensure

smooth movement of the camera about these axes and are fitted with control knobs ([9], [11]) to

adjust the drag setting. The drag controls are mounted on the left side of the head. The whip-

pan facility is unaffected by the pan drag setting.

Pan and tilt brakes

Friction brakes on each axis allow the head to be locked at any chosen position. The operating

levers for both brakes ([4], [5]) are fitted on the lower right rear of the head. A tilt axis centre lock

[16] is provided on the right side of the head to secure the platform in the horizontal position

during transport or load changing.

Illuminated level bubble

A level bubble [8] is fitted to the rear of the head and is provided with a time-delay illumination

unit, operated by a switch [7]. The battery for the illumination unit is contained in the base.

Pan bar

Pan bar mounting points [18] are located at the rear of the head, on either side of the camera

mounting platform. A telescopic pan bar is supplied and is attached using a pan bar clamp [10],

with angular adjustment available on the mount serrations. A second pan bar may be fitted;

telescopic and fixed short or extra short pan bars are available as optional extras.

Camera mounting

The camera is attached to the head by means of a wedge adaptor [1].

English

8

Operation

Unpacking

The head is supplied with a telescopic pan bar, automatic wedge adaptor and a battery (already

fitted) for the level bubble illumination unit.

A second telescopic or fixed short or extra short pan bar for use with a zoom or focus controller

is optional. Ensure that all items are unpacked prior to disposal of the packing materials.

After unpacking ensure that:

The pan and tilt brakes ([4], [5]) are on (see Pan and tilt brakes on page 11).

The centre lock [16] is engaged (see Locking the platform on page 11). Always

engage the centre lock before lifting or carrying the head.

Mounting the head

The head is mounted on a tripod, pedestal or suitable firm surface using the four fixing bolts and

washers. The four bolt-fixing holes [19] on the underside of the head are easily located using the

bolt-hole position indicators [20]. Tighten the bolts with the spanner provided.

After mounting the head, ensure it is level using the level bubble [8], which may be illuminated

by pressing the switch [7]. The light will go out after 15 seconds (timeout function).

Pan bars

Fit the pan bars to the head and adjust the position of each one before tightening the clamp [10]

on the mounting [18]. Adjust the length of the telescopic pan bar(s).

CAUTION! Do NOT lift the head by the platform. Only use the base and/or the

carrying handle to prevent damaging the head.

NOTE: When mounted on Vinten ‘Hawk’ or ‘Teal’ pedestals, clearance between the

head and the pedestal weight tray prevents the use of 1.6 kg (5.5 lb) and

0.5 kg (1.0 lb) trim weights. Use alternative weights or fit the adaptor plate

kit (part no. 3354-900SP) between the head and pedestal.

WARNING!

1. Only mount this product on equipment designed to support a

minimum of 95 kg (109 lb).

2. Before installing the head, hold a fixing bolt in position and check that

the threaded end does not project more than 20 mm (3/4 in.) above the

mounting face.

English

9

Fitting a camera

To fit a camera, proceed as follows:

Lower the mounting to a convenient working height.

If not already fitted, install the wedge adaptor [1] in the middle position on the slide plate

[14] (see Repositioning the wedge adaptor on page 14).

Attach the wedge to the camera/lens.

Ensure that the centre lock [16] is engaged (see Locking the platform on page 11).

Apply the pan brake [4] (see Pan and tilt brakes on page 11)

.

Slide the wedge adaptor lever [2] forward (parallel to the wedge) about 6 mm (1/4 in.)

against spring tension. Pull the lever out, away from the body of the wedge adaptor, as

far as it will go.

Insert the camera wedge into the wedge adaptor [1] and push it forward until it is fully

engaged. Push in the wedge adaptor lever [2], until it lies parallel with the wedge adaptor

body. During this operation the resistance of the spring-loaded over-centre mechanism

will be felt. As the lever reaches the end of its travel, it will snap into the locked position

(indicated by the closed padlock symbol above the lever).

Confirm that the lever is locked by briefly pulling it outward, away from the wedge

adaptor body. If the lever is locked, it should not move and the closed padlock

symbol only should be visible.

Install the remainder of the payload (e.g. lens, zoom and focus controls, viewfinder,

prompter etc.).

Balancing the head

Balancing the head consists of positioning the payload fore and aft on the head so that its C of G

is immediately above the platform pivot, then compensating for the payload C of G height using

the Perfect Balance adjustment knob.

WARNING!

1. Do NOT rely on the tilt brake when changing the payload. Always

engage the centre lock.

2. Ensure that the weight and C of G height of the total payload is within

the range for which the head is designed: up to 75 kg (165.3 lb) with a

C of G height of 80–250 mm (3–10 in).

NOTE: It is important that the pan bar(s) and all camera accessories (lens, zoom

and focus controls, viewfinder, prompter etc.) are fitted in their operational

position before balancing the head.

Any equipment fitted or adjusted later will unbalance the head.

English

10

Position the payload fore and aft as follows:

Ensure that the centre lock is engaged (see Locking the platform on page 11) and that

the camera and all accessories are fitted.

Turn the tilt drag adjustment knob [11] to its minimum setting.

Holding the pan bar to steady the platform, press down the release catch [17] to

disengage the centre lock (see Locking the platform on page 11).

Push the clamp lever [12] downward to release the slide plate clamp and pull out the

slide plate adjustment knob or ‘T’ bar [13] until it engages with the platform drive. Turn

the ‘T’ bar to move the slide plate fore and aft to achieve horizontal balance.

The horizontal balance is correct when no perceptible tilting force can be felt on the pan

bar with the platform level. Apply the slide plate clamp [12] by pulling the clamp lever

upward.

If there is insufficient movement in the slide plate to achieve balance, reposition the wedge

adaptor (see Maintenance on page 12), refit the load and repeat the horizontal balancing

procedure.

When fore and aft balance has been achieved, adjust the payload C of G height as follows:

Using the pan bar, tilt the platform forward and backward. When correctly balanced,

there should be no perceptible tilting force on the pan bar at any angle of tilt and the head

should remain in any tilt position to which it is set.

If the head tends to fall away when the platform is tilted, push and turn the Perfect

Balance adjustment knob [15] clockwise to increase the C of G height setting. If the head

tends to spring back to centre, push and turn the Perfect Balance adjustment knob [15]

counter-clockwise to decrease the C of G height setting.

When the payload C of G height adjustment is complete, check that the fore and aft

balance remains satisfactory. Readjust the position of the slide plate if necessary.

After balancing, release the brakes and exercise the head through both axes to confirm that it

operates smoothly.

WARNING!

Increase the balance setting for a heavy, out-of-balance payload BEFORE

disengaging the centre lock, to prevent the platform tipping violently.

WARNING!

Keep a firm grip on the pan bar to steady the camera payload.

Be prepared to prevent the head falling away suddenly.

NOTE: The Perfect Balance adjustment knob is a multi-turn control. To enable the

knob to be turned more easily, slightly tilt the platform using the pan bar

whilst turning the knob.

English

11

Locking the platform

(Fig 4)

The centre lock mechanism is operated by a button [16] on the right side of the head. To engage

the lock, hold the platform in the horizontal position and push the button [16] inwards, until it

latches and the release catch [17] appears. Use the pan bar to rock the platform slightly whilst

pushing the button [16].

To release the centre lock, rock the platform slightly and push down on the release catch [17].

Pan and tilt brakes

The pan and tilt brakes are operated by levers ([4], [5]) at the rear of the head. They are applied

by pulling the appropriate lever up and back and released by pushing the lever forwards.

The brakes should be applied whenever the camera is left unattended.

Pan and tilt drag

The pan drag adjustment knob [9] is mounted on the left lower part of the main body. Tilt drag is

adjusted by a knob [11] mounted on the face of the tilt drag housing on the left side of the head.

Turn the knobs clockwise to increase drag and counter-clockwise to decrease drag.

WARNING! FINGER TRAP

Keep fingers clear of the platform underside when tilting to avoid

personal injury.

CAUTION!

1. Do NOT use force on the brake levers. Hand tighten only.

2. Do NOT use the brakes to supplement drag, the head may be damaged.

When the brakes are not in use, always ensure they are fully released.

CAUTION! Reduce drag to a minimum when the head is out of use for long periods,

to minimise wear on drag components.

CAUTION

finger trap

English

12

Maintenance

General

The Vector 75 pan and tilt head is robustly made to high engineering standards and little

attention is required to maintain serviceability except regular cleaning. Adjustments and repairs

should be carried out only by a competent person.

Cleaning

During normal use the only cleaning required should be a regular wipe over with a lint-free cloth.

Dirt accumulated during storage or periods of disuse may be removed with a vacuum cleaner.

Particular attention should be paid to the wedge location faces of the wedge adaptor.

Use out-of-doors under adverse conditions may require special attention, and the head should

be covered when not in use. Salt spray should be washed off using fresh water at the earliest

opportunity. Sand and dirt act as an abrasive and should be removed using a vacuum cleaner

or a supply of clean, dry air.

Cleaning balance mechanism tracks

The balance mechanism tracks are automatically cleaned by built-in wipers, but after use in

particularly adverse conditions the tracks may require cleaning. Some dismantling of the head

is necessary and it is recommended that this be carried out in clean workshop conditions.

Vertical tracks (Fig 5)

To clean the vertical tracks it is necessary to remove the platform; proceed as follows:

Remove the payload (if fitted). It is not necessary to remove the wedge adaptor.

Release the slide plate clamp [12]. Use the adjustment knob [13] to wind the slide plate

[14] backwards until it is clear of fixing screws [21].

Level the platform.

Remove six screws [21] securing the platform [22] to the balance mechanism [23]. Lift

off the platform.

Using a pipe cleaner (or similar) moistened with an isopropanol-based cleaner (3M

VBH or similar) clean the two vertical tracks [24]. Upwards pressure on the balance

mechanism will allow the area of track under the vertical rollers to be cleaned.

Install the platform [22] on the balance mechanism [23] and secure with six screws [21]

using Loctite 222E.

Using the adjustment knob [13] wind the slide plate forwards to the central position.

Refit the payload (if required) and rebalance the head.

CAUTION! DO NOT use solvent- or oil-based cleaners, abrasives or wire brushes to

remove accumulations of dirt as these damage the protective surfaces.

To clean mechanical surfaces, use only detergent-based cleaners.

English

13

Horizontal tracks (Fig 6)

No dismantling is necessary to clean the horizontal tracks; proceed as follows:

Remove the payload (if fitted).

Set the balance mechanism to its maximum setting by pushing in the Perfect Balance

knob [15] and turning it clockwise to its stop.

Tilt the platform fully backwards and apply the tilt brake [5].

Pull down the flap guard [28] to reveal the bevel gear [26]. Access to the horizontal

tracks [27] is through the holes in the bevel gear, which may be rotated freely.

Using a pipe cleaner (or similar) moistened with an isopropanol-based cleaner (3M VBH

or sim.), clean the two horizontal tracks. Upwards pressure on the balance mechanism

will allow the area of track under the horizontal rollers to be cleaned.

Release the flap guard [28] and the tilt brake [5] and return the platform to the horizontal

position.

Refit the payload (if required).

Routine maintenance

Routine maintenance on the Vector 75 pan and tilt head is limited to annual replacement

of the level bubble illumination battery.

During normal use, check the effectiveness of the platform slide clamp and the

adequacy of level bubble illumination.

No further routine maintenance is required.

Replacing the battery

(Fig 7)

The level bubble on the Vector 75 pan and tilt head is illuminated by a battery-powered LED. A

time-delay circuit initiated by a switch controls the LED. The battery should be replaced at yearly

intervals or whenever the illumination is considered inadequate.

To install or replace the battery proceed as follows:

Remove three screws [29] which secure the battery compartment cover plate [32].

Install the battery [30] by pushing the connector [31] onto the battery terminals.

Position the battery in the battery compartment, ensuring that the wiring is not trapped.

Refit the battery compartment cover plate [32], ensuring battery locates in cover plate.

Secure with three screws [29].

Press the switch [7] and ensure the LED is lit for approximately 15 seconds.

NOTE: Dependent on the type of mounting, it may be necessary to remove the

head from the mounting for access to the battery compartment.

English

14

Adjustments

After considerable use the slide plate clamp may require adjustment.

To enable the payload to be correctly balanced, the wedge adaptor may require

repositioning.

The pan and tilt brakes may require adjustment after considerable use.

Adjusting the slide plate clamp

(Fig 8)

The slide plate clamp [12] should be set so that in the up or clamped position it prevents the slide

plate from being moved, while in the down or released position it allows free adjustment of the

slide plate. To adjust the clamp, proceed as follows:

On the left-hand side of the platform, carefully remove the plastic cap [12.2] to reveal the

slotted shaft [12.1].

Pull the slide plate clamp lever [12] fully upwards.

Slacken the clamp screw [12.3].

Turn the slotted shaft [12.1] fully clockwise to apply the clamp.

Tighten the clamp screw [12.3].

Move the lever over its full range and ensure that in the clamped position it prevents the

slide from being moved, while in the released position it allows free adjustment of the

slide. Readjust if necessary.

Replace the plastic cap [12.2] over the slotted shaft [12.1].

Repositioning the wedge adaptor

(Fig 9)

The wedge adaptor [1] is secured by four cap head screws [3] which pass through the wedge

adaptor into the slide plate [14].

To reposition the wedge adaptor:

Engage the centre lock (see Locking the platform on page 11) and remove the load.

Hold the body of the wedge adaptor [1] and use a 4 mm hexagon wrench to remove four

securing screws [3].

Reposition the wedge adaptor [1] on the slide plate [14], ensuring that the narrow end

of the wedge adaptor faces forwards.

Insert the four screws [3] in the holes in the wedge adaptor and tighten.

WARNING!

Overlong screws will prevent the slide plate from operating. Always use the

screws provided (M6 x 30 mm).

English

15

Adjusting the pan and tilt brakes

(Fig 10)

The pan and tilt brakes should be set so that the brakes begin to be applied after approximately

one-third of the lever travel. The tilt brake is adjusted by inserting a 2 mm hexagon wrench

through the hole [5.2] in the bottom of the tilt unit cover and turning the grub screw [5.1].

To adjust the tilt brake, proceed as follows:

Operate the tilt brake lever [5] from the OFF to the ON position.

If brake pressure is not felt after approximately 1/3 of lever travel, turn the grub screw [5.1]

clockwise until this is achieved.

Operate the tilt brake lever [5] to the OFF position and ensure that the platform is free

to move.

The pan brake is adjusted by turning the pin [4.3]. To gain access to the pin it is necessary to

remove the payload from the head, remove the head from its mounting and remove a cover plate

[4.1] from the underside of the head.

To adjust the pan brake, proceed as follows:

Remove the payload from the head.

Remove the head from its mounting.

On the underside of the head, remove three screws [4.2] securing the cover plate [4.1].

Operate the pan brake lever [4] from the OFF to the ON position.

If brake pressure is not felt after approximately 1/3 of the lever travel, turn the pin [4.3]

clockwise until this is achieved.

Set the pan brake lever [4] to the OFF position and ensure that the head is free to rotate.

Refit the cover plate [4.1] and secure with three screws [4.2].

WARNING!

Remove the payload before adjusting the pan brake.

English

16

Parts list

The following list includes main assemblies, user-replaceable spare parts and optional

accessories. For further information regarding repair or spare parts, please contact Vinten or

your local Vinten distributor. For more information visit our website at www.vinten.com.

Main assemblies

Vector 75 pan and tilt head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V4095-0001

Telescopic pan bar and clamp assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3219-82

Automatic wedge adaptor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3460-3

Fixing bolts (4 off). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . L054-714

Washers (4 off, for fixing bolts). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . L602-122

Spanner (for head bolts). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J551-001

Battery (9V, PP3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C550-023

User-replaceable spare parts

Level bubble illumination unit battery – 9V, 6LR61

(PP3, 6AM6, MN1604, E-BLOCK or equivalent) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C550-023

Vinten Flat-Base Head-Fixing Kit (SP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V4095-1902

Optional accessories

Lightweight Mitchell adaptor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3103-3

Heavy-duty Mitchell adaptor for Vinten pedestal

mounting in conjunction with Hi-hat Adaptor, part no. 3055-3 . . . . . . . . . . . . . . . . . . . . . 3724-3

Adaptor Plate Kit (for use on ‘Hawk’ and ‘Teal’ pedestals). . . . . . . . . . . . . . . . . . . .3354-900SP

Camera wedges for wedge adaptor:

Short wedge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3391-3

Standard wedge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3053-3

Short fixed pan bar and clamp assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3219-94

Extra short fixed pan bar and clamp assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3219-93

Telescopic pan bar and clamp assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3219-82

Deutsch

17

Inhalt

Seite

Sicherheitshinweise – Unbedingt zuerst lesen! . . . . . . . . . . . . . . . . . . . . . . . . 18

Warnsymbole in dieser Bedienungsanleitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Nutzung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Umweltverträglichkeit durch Recycling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Technische Daten. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Einführung und Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Perfect Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Schwenk- und Neigungsdämpfung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Schwenk- und Neigungssperren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Beleuchtete Nivellierlibelle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Schwenkarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Kameramontage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Bedienung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Auspacken. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Befestigen des Kopfes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Schwenkarme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Anbringen der Kamera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Ausbalancieren des Kopfes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Verriegeln der Plattform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Feststellbremsen für beide Achsen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Schwenk- und Neigedämpfung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Wartung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Allgemeines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Reinigung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Reinigung der Spuren des Balancierungsmechanismus. . . . . . . . . . . . . . . . . . . . . . .27

Routinemäßige Wartung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Batterie wechseln . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Einstellungen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Plattformgleitklemme einstellen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Neuausrichtung des Keilplattenadapters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Feststellbremsen für beide Achsen einstellen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Teilelisten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Deutsch

18

Sicherheitshinweise – Unbedingt zuerst lesen!

Warnsymbole in dieser Bedienungsanleitung

WARNUNG

Dort, wo die Gefahr einer Verletzung für Sie oder andere besteht, sind Kom-

mentare durch das Wort WARNUNG! besonders hervorgehoben – unterstützt

durch das dreieckige Warnsymbol.

Dort, wo die Gefahr von Schäden am Produkt, an zugehöriger Ausrüstung, dem

Prozess oder der Umgebung besteht, sind Kommentare durch das Wort VOR-

SICHT! gekennzeichnet.

QUETSCHGEFAHR

Wenn die Gefahr besteht, sich die Finger am Produkt oder an anderen am Produkt

angebrachten Komponenten zu quetschen oder einzuklemmen, werden ent-

sprechende Hinweise in Verbindung mit dem Symbol „Finger Trap“ angezeigt.

Nutzung

Der Vector 75 Schwenk-/Neigekopf wurde zur Verwendung im Broadcast-Bereich und in Film-

studios als Support und Balancierungsvorrichtung für Kamera und Zusatzausrüstung mit einem

Gewicht von bis zu 75 kg entwickelt, und ist auf Geräten mit einer Mindesttraglast von 95 kg

zu befestigen.

Der Vector 75 Schwenk-/Neigekopf wurde für den professionellen Einsatz durch TV-Broadcast-

und Filmkameraleute konzipiert.

Umweltverträglichkeit durch Recycling

Entsorgung von Altbatterien

Die mit diesem Produkt gelieferten Batterien dürfen nicht in den Hausmüll gegeben werden.

Sorgen Sie dafür, dass diese Batterien angemessen entsorgt werden. Sie helfen damit, die

Umwelt und unsere natürlichen Ressourcen zu schonen und Gesundheitsschäden zu ver-

meiden. Geben Sie die Batterie an einem Sammelpunkt zum Recycling von Altbatterien ab.

WARNUNG!

1. Verwenden Sie dieses Produkt NICHT, wenn Sie nicht sicher sind, wie

es zu bedienen ist.

2. Verwenden Sie dieses Produkt NICHT zu einem anderen Zweck als der

unter „Nutzung“ beschriebenen Verwendung.

3. Wenden Sie sich bezüglich aller Wartungsarbeiten, die über die in

dieser Bedienungsanleitung beschriebenen Maßnahmen hinaus-

gehen, an ein autorisiertes Vinten Service Centre.

CAUTION

finger trap

Deutsch

19

Technische Daten

Maximale Traglast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 kg

Traglast Schwerpunkthöhenbereich. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80–250 mm

Gewicht (komplett mit Schwenkarm und Keilplattenadapter). . . . . . . . . . . . . . . . . . . . . 19,15 kg

Gesamtmaße

Höhe (mit Keilplattenadapter):

Minimale Balance-Einstellung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 mm

Maximale Balance-Einstellung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355 mm

Länge (ohne Schwenkarm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355 mm

Breite (ohne Schwenkarm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 mm

Breite (mit zwei Schwenkarmen) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445 mm

Neigebereich . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±52

Schwenkbereich. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360

Gewichtsausgleich . . . . . . . . . . . . . . . . . . . . . . . .vollständig variables Perfect Balance-System

Nivellierlibelle . . . . . . . . . . . . . . . . . . . . . . . . . beleuchtet mit einer kontrastreichen, blauen LED

Beleuchtung Niverllierlibelle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Sekunden (Timeout)

Batterietyp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PP3 (9V)

Stativbefestigung . . . . . . . . . . . . . . . . . . . . Vier-Loch-Flachboden mit Quickfix

®

-Nut (Standard)

La pagina sta caricando ...

Vinten Vector 75 Operator Guide

Vinten Vector 75 Operator Guide

in altre lingue

Documenti correlati

Altri documenti