Printek 8000 Manuale utente

FormsMaster 8000 Series

High Performance

Serial Matrix Printers

Operator’s Manual

©Printek, Inc. 1997

1517 Townline Road

Benton Harbor, MI 49022

616-925-3200

Part Number 4339

ii

This equipment has been tested and found to comply with the limits for a Class A Digital

Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference in which case the user will be required to correct the interference at his own

expense.

The user is cautioned that any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate the

equipment.

This digital apparatus does not exceed the Class A limits for radio noise emissions as set

out by the ICES-003 standard, of the Canadian Department of Communications.

Cet appareil numérique n’émet pas de bruits radioélectroiques depassant les limites de

Classe A prescrites dans la norme NMB-003 Édictée par le Ministre des

Communications du Canada.

Acknowledgments:

IBM, Proprinter, and IPDS are registered trademarks of International Business

Machines Co.; DEC is a registered trademark of Digital Equipment Corporation; Epson

is a registered trademark of Seiko Epson; QMS is a registered trademark of Quality

Micro Systems, Inc.; IGP is a registered trademark of Printronix Corp.; Printek is a

registered trademark of Printek, Inc.

Specifications are subject to change without notice.

iii

Table of Contents

Introduction

Models and Options 1

Manual Contents 1

Getting Started

Installation 3

Interface Set Up 4

Installing The Ribbon Cartridge 8

Why Use Only Printek

®

Brand Ribbons 8

Ribbon Installation 10

Loading Paper 13

FormsMaster 8000 Single Tractor Model 13

FormsMaster 8003 TriTrak™ Model 14

Printer Self-test 17

Daily Operation

Introduction 19

Control Panel Features 20

LCD Display and Online Indicator 20

Push Buttons 21

Selecting and Loading Forms 25

Selecting a Form Already Loaded in the Tractors 25

Loading a New or Different Form In the Tractors 25

Ejecting and Tearing Off a Form 30

Installing a New Ribbon Cartridge 32

Aligning Print 34

Common Error Conditions 36

Check Paper 36

No Paper to Load 36

Too Much Paper to Unload 37

Selected Form is not Loaded 37

No Ribbon or Wrong Ribbon 37

Ribbon Lid Open 37

Paper Door Open 37

Change Ribbon 38

iv

Printer Configuration

Introduction To Setup 39

Setup Buttons 39

Entering Setup 40

Using the MENU Button 40

Using the SUBMENU Button 40

Using the ITEM and VALUE Buttons 41

Exiting Setup 41

Forms Menu 42

Forms Menu Items 43

Interface Menu 49

Automatic Port Switching 49

RS-232C Serial Interface Items 51

Parallel Interface Items 55

Ethernet 10BaseT LAN Interface Items 57

Coaxial/Twinaxial Interface Items – Coax Configuration59

Coaxial/Twinaxial Interface Items – Twinax Configuration

63

IPDS Coax Interface Items 67

IPDS Twinax Interface Items 72

Imager and ImagerPlus Interface Items 74

Options Menu 79

Test Menu 82

Form Construction and Layout Tips

Form Construction 85

Form Layout Considerations 85

Maintenance and Troubleshooting

Messages 87

Preventive Maintenance 88

Obtaining Service 88

Advanced Setup Features 89

Using Remote Setup 91

Using the Optional Setup Module 99

Printer Reset Conditions 105

Control Code and Escape Sequence Summaries

v

ANSI X3.64 Emulation 107

Epson FX Emulation 109

IBM Proprinter Emulation 111

LA-120 Emulation 113

Simple TTY Emulation 115

Printek Emulation 116

ASCII Character Tables 117

Specifications 121

Glossary of Terms 127

1

Introduction

Thank you for purchasing a Printek FormsMaster 8000 Series Printer.

This printer has been designed to provide years of service handling your

most demanding printing requirements.

The FormsMaster 8000 Series printers offer higher throughput than all other

printers in its class. In addition, an easy to use front panel combined with

the ability to store ten different form configurations makes handling multiple

forms as simple as a button press for the operator.

Models and Options

The FormsMaster 8000 and the FormsMaster 8003 differ only in the

number of tractor paths available, one path or three.

Options available for both models include:

Coaxial and Twinaxial Interface

Coaxial IPDS Interface

Twinaxial IPDS Interface

Ethernet 10BaseT Interface

Imager Bar Code Coprocessor

ImagerPlus Bar Code Coprocessor

Print Stand (required for reduced sound levels)

Internal FormsCutter

Setup Module

Manual Contents

• Getting Started provides instructions for installation, setting up

the computer interface, installing the ribbon cartridge, loading

paper, and performing a printer self-test.

• Daily Operation provides more detailed descriptions of the features

that are used most frequently. These include the “every day”

buttons and indicators on the control panel, selecting or loading

new forms, ejecting forms, changing the ribbon cartridge, aligning

I N T R O D U C T I O N

2

print with preprinted forms, and causes for common error

conditions.

• Printer Configuration provides detailed information on how to

use Setup to permanently store parameters for each of the ten forms,

parameters for the standard and optional interfaces, and parameters

for other options.

• Specifying Forms provides tips for form construction and layout.

• Maintenance and Troubleshooting lists more serious error

messages than discussed in the Daily Operation section,

preventive maintenance, and how to obtain service.

• Advanced Setup Features provides information on how to set

menu security.

• Using Remote Setup describes how to “set up” default parameters

from a host computer.

• Using the Setup Module describes how the optional Setup

Module can be used to copy Setup parameters from one printer to

another.

• Printer Reset Conditions describes the state of the printer after

power up or reset.

• Control Code and Escape Sequence Summaries lists the

commands supported for each printer emulation.

• ASCII Character Tables show the characters for each character set.

• Specifications lists the operating ranges and ratings of the printer.

• Glossary of Terms provides definitions for terms used in this

manual.

3

Getting Started

This chapter will use the fewest possible steps to get the first time user up

and running quickly. You will be guided through the following steps:

Finding a suitable location and installing the printer

Setting up a host interface if necessary

Installing the ribbon cartridge

Loading paper

Performing a printer self-test

INSTALLATION

Before installation, a suitable site must be chosen. Suitable sites include

offices, computer rooms, and most factory environments. The Printek

FormsMaster printers have been designed to be rugged, heavy duty printers.

As such, they will handle most harsh environments, but should not be

placed in direct sunlight or in areas that will exceed the rated temperature,

humidity, or power requirements. For details, refer to “Specifications” on

page 121.

Once a site has been selected, the printer should be placed on a Printek Print

Stand. The Printek print stand is especially recommended for the

FormsMaster 8003 and is required to meet the low noise rating of the

printer. Of course, another sturdy print stand or table with a slotted top for

feeding paper into the bottom of printer may be used.

The print stand should be located in an area large enough to provide easy

access to both the front of the printer and the rear for accessing printed

output. Unpack the printer as described in the “FormsMaster 8000

Unpacking Instructions” and place the printer on the print stand.

Note: Placing the printer on the print stand is best accomplished with two

people. Proper lifting technique should be observed.

Caution: Before connecting or turning on power, make sure that all

shipping materials have been removed. These materials include

G E T T I N G S T A R T E D

4

a cable tie that secures the print head carriage (open ribbon lid to

access) and two cardboard tubes placed over the tractor shuttle

shafts in the FormsMaster 8003 (open paper door on front of

unit to access).

Next, connect the power cord supplied with the printer to the printer and an

appropriate power outlet. Now connect the computer cable(s) to the

appropriate interface. The picture below shows the location of the standard

Parallel and RS-232C interface connectors on the rear panel of the printer.

The area where an optional CX/TX, ICX, ITX, or LAN interface may be

installed is also indicated.

Interface Connectors on Rear of Printer

INTERFACE SET UP

Depending upon which interface is being used to connect the printer to the

host computer, some set up may or may not be required. Regardless of

which interface is used, the FormsMaster 8000 will automatically detect

which port is receiving data and make that port active. This is true of the

standard parallel or serial ports and any optional interface that may be

installed. For more information, see “Automatic Port Switching” on page

49.

G E T T I N G S T A R T E D

5

The factory default settings for each interface should work well for most

installations. However, the following paragraphs provide some basic

information about each interface and also refer to the page number in the

Configuration chapter where all the details for each interface are described. If

you need to make changes to the default settings, please refer to

“Introduction to Setup” on page 39 for instructions on how to access the

printer’s Setup menus.

Once you are comfortable that the interface settings match those required by

your computer, proceed to the next section, “Installing the Ribbon

Cartridge” on page 8.

RS-232C Serial Interface

This interface uses a 25 pin “D” connector as described below. The default

settings are 9600 baud, 8 data bits, 1 stop bit, and no parity with hardware

handshake on pin 11. The default printer emulation is Epson. For a

complete description of all the default settings for this interface, refer to page

51.

Pin Signal

1

2

3

4

5

6

7

8

11

20

Chassis ground.

Transmit data. (Printer output).

Receive data. (Printer input).

Request to send (set). (Printer output).

Clear to send (ignored). (Printer input).

Data set ready (ignored). (Printer

input).

Signal ground.

Carrier detect (ignored). (Printer input).

Printer busy. (Printer output).

Data terminal ready. (Printer output).

RS-232C Serial Interface Connector.

G E T T I N G S T A R T E D

6

Parallel Interface

This interface uses the standard 36 pin parallel connector as shown below.

The default printer emulation is Epson. For a complete description of all

the default settings for this interface, refer to page 55.

Pin Signal Pin Signal

1

19

2

20

3

21

4

22

5

23

6

24

7

25

8

26

9

27

____________________

DATA STROBE

DATA STROBE RTN

DATA 1

DATA 1 RETURN

DATA 2

DATA 2 RETURN

DATA 3

DATA 3 RETURN

DATA 4

DATA 4 RETURN

DATA 5

DATA 5 RETURN

DATA 6

DATA 6 RETURN

DATA 7

DATA 7 RETURN

DATA 8

DATA 8 RETURN

10

28

11

29

12

13

14

16

17

18

31

30

32

35

36

_______________________

ACKNOWLEDGE

ACKNLG RETURN

BUSY

BUSY RETURN

PAPER ERROR

SELECT

________________

AUTO FEED

±0V

CHASSIS GROUND

+5V at 200mA Max.

______

INIT

INIT RTN

_________

FAULT

+5V LOGIC HIGH

______________

SELECT IN

Parallel Interface Connector

G E T T I N G S T A R T E D

7

Ethernet 10BaseT

This interface uses a standard RJ-45 connector and the default printer

emulation is Epson. For a complete description of all the default settings

for this interface, refer to page 57. For additional software installation and

operational information, please refer to the Axis manuals shipped with the

unit (disregard the Axis physical installation information).

Coax/Twinax Interface

This interface automatically sets itself for either Coax Mode or Twinax

Mode depending upon which adapter cable (coax BNC or twinax smart

“T”) is attached to the 15 pin “D” connector when the printer is powered

on. Only the choices for the detected mode are available in the Setup

menus.

For Coax Mode, the default emulation is for a 3287 printer. For a complete

description of all the default settings for the Coax interface, refer to page 59.

For Twinax Mode, the default emulation is for a 4214 printer. For a

complete description of all the default settings for the Twinax interface, refer

to page 63.

IPDS Coax Interface

This interface uses a coax BNC adapter connected to the 15 pin “D”

connector on the rear of the printer. The default values should work in most

cases. For a complete description of all the default settings for this interface,

refer to page 67.

IPDS Twinax Interface

This interface uses a twinax smart “T” adapter connected to the 15 pin “D”

connector on the rear of the printer. The default values should work in most

cases. For a complete description of all the default settings for this interface,

refer to page 72.

G E T T I N G S T A R T E D

8

INSTALLING THE RIBBON CARTRIDGE

The Printek FormsMaster printer has been designed to make installing

Printek brand ribbons a simple, clean process. Unlike other printers, there

is no need to touch the ribbon fabric or deal with difficult to position ribbon

guides. The following sections explain why the use of Printek brand

ribbons should be important to you and will guide you through installing

the ribbon cartridge.

Why Use Only Printek

®

Brand Ribbons

Printek

®

Brand Ribbon Label

Printek brand ribbons can be identified by the above label on each ribbon.

There are many reasons to use only Printek brand ribbons in your

FormsMaster 8000 series printer. First of all, using

only Printek brand

ribbons will automatically extend the print head warranty to two years

instead of one year.

The reason this is possible is that Printek brand ribbons are manufactured to

much higher quality standards than those offered by other manufacturers.

This provides not only longer print head life, but also longer ribbon life…

23 million characters as compared to only 15 million characters from some

generic ribbons.

Remember that using only Printek brand ribbons is important because the

wear that is started and the contamination that remains from even one

inferior ribbon will continue to damage the print head. Also, damage to

other printer components which is caused by the use of non-Printek ribbons

will not be covered by the printer’s warranty.

Using inferior ribbons would be like using poor quality fuel in your

automobile. Premature engine failure and poor performance leading up to

the failure would be the best you could expect.

REORDER NUMBER 90729

FOR NEAREST DISTRIBUTOR

CALL 1-800-368-4636

G E T T I N G S T A R T E D

9

Other useful features available only with the use of Printek brand ribbons are

that the printer will not allow printing if a ribbon is not installed, and the

printer will alert the operator when a ribbon needs to be changed.

G E T T I N G S T A R T E D

10

Ribbon Installation

1. Open the ribbon lid on top of the printer and position the print head

for ribbon loading by lifting the ribbon loading handle as indicated in

the following picture.

Opening the Ribbon Loading Handle

2. Remove the new ribbon from its plastic bag and make sure the ribbon

fabric is taut by turning the knob on top of the ribbon cartridge in a

counterclockwise direction as indicated by the arrow on the cartridge.

G E T T I N G S T A R T E D

11

3. With the right hand end of the ribbon tilted down, insert the tab on

the end of the cartridge into the opening in the ribbon tray.

Installing the Ribbon Cartridge

4. Now lower the left end of the cartridge down while guiding the

ribbon fabric between the nose of the print head and the ribbon guide

pins. Continue to lower the cartridge until the tab on the left end of

the cartridge snaps into place.

Ribbon Guided Between the Print Head

and Guide Pins

G E T T I N G S T A R T E D

12

5. Finally, lower the ribbon loading handle to its original position.

Closing the Ribbon Load Handle

6. Close the ribbon lid on top of the printer.

G E T T I N G S T A R T E D

13

LOADING PAPER

When shipped from the factory, the basic configuration for all ten forms is an

eleven inch form, six lines per inch, and ten characters per inch. If the forms

you are loading do not match these requirements, please refer to the “Printer

Configuration” chapter on page 39 and review the “Using Setup” and

“Forms Menu” sections.

Please refer to the appropriate section below for loading paper in the

FormsMaster 8000 or FormsMaster 8003.

FormsMaster 8000 Single Tractor Model

1. Make sure the printer is powered on and that the printer is off line

(ONLINE indicator flashing red).

2. Lift open the paper door on the front of the printer to expose the paper

feed tractors as shown below.

FormsMaster 8000 Tractors

3. Open the doors on each tractor.

4. Feed the paper up through the bottom of the printer and position the

holes in the edge of the paper over the pins in the left tractor while

making sure that the paper will not extend above the top of the

tractors. Then close the tractor door.

G E T T I N G S T A R T E D

14

Note: The left tractor position is not adjustable. If it is necessary to

adjust where printing begins, refer to “Aligning Print” in the

“Daily Operation” section of this manual.

5. Now position the paper in the right tractor in the same fashion. If

necessary, the position of the right tractor may be adjusted. To do

so, move the lever on the side of the tractor down to unlock the

tractor and slide the tractor sideways on the shafts. If necessary, the

paper guides between the tractors may be slid in either direction to

accommodate the form width. Make sure that the guides are spaced

evenly between the tractors.

After the paper is placed in the tractor and the door is closed, position

the tractor far enough to the right so that there is no buckle in the

paper between the tractors, but not so tight that the holes in the paper

are distorted. Lock the tractor in place by returning the lever to the

up position.

6. Close the paper door.

7. Press the LOAD button.

8. Place the printer on line by pressing the ONLINE button.

FormsMaster 8003 TriTrak™ Model

The following instructions will guide you through loading all three tractor

paths.

1. Make sure the printer is powered on and that the printer is off line

(ONLINE indicator flashing red).

2. Press the UNLOAD button to move the tractor shuttle forward to the

load position.

3. Lift open the paper door on the front of the printer to expose the paper

feed tractors as shown in the following picture.

La pagina si sta caricando...

Printek 8000 Manuale utente

Questo manuale è adatto anche per

Printek 8000 Manuale utente

in altre lingue

Documenti correlati

Altri documenti