Schwaiger DSR 1004 CW Manuale utente

Categoria
Set-top box TV
Tipo
Manuale utente
Digital Satellite Receiver
User's Manual
DSR 1004 CW
Cryptoworks embedded
GB
D
S
I
060615_K7_KSF-200CX_Schwaiger_Sa3 3 2006-06-15 오후 7:09:17
060615_K7_KSF-200CX_Schwaiger_Sa13 13 2006-06-15 오후 7:20:04
COVER_ENG
Digital Satellite Receiver
User's Manual
Distributed by SCHWAIGER GmbH
Würzburger Str. 17
90579 Langenzenn
-Germany-
Tel Hotline +49
(
0
)
9101 702 299
www.schwaiger.ed
info@schwaiger.ed
DSR 1004 CW
Cryptoworks embedded
GB
060615_K7_KSF-200CX_Schwaiger_Sa5 5 2006-06-15 오후 7:08:47
General Safety
Warning
Always follow these instructions to avoid the risk of injury to
yourself or damage to your equipment.
Unplug the receiver from the AC power outlet before cleaning.
Use only a damp cloth for cleaning the exterior of the receiver.
Do not use accessories or attachments not recommended by the receiver manufacturer
as they may cause problems to the equipment and will void the warranty.
Do not place the receiver on an unstable cart, stand, tripod, bracket, or table.
The receiver may fall, causing serious personal injury and damage to the receiver.
Do not block or cover the slot opening in the receiver.
These are provided for ventilation and protection from overheating.
Never place the receiver near or over a radiator or any heat source.
Do not place the receiver in an enclosure such as a cabinet without proper ventilation
Do not stack the receiver on top of or below other electronic devices.
The apparatus shall not be exposed to dripping or splashing and with no object filled with liquids,
such as vases, shall be placed on the apparatus.
Operate the receiver using only the type of power source indicated on the marking label.
Unplug the receiver power cord by gripping the power plug, not the cord.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 1 mac-4 HP LaserJet 5100 Series T
General Safety
Servicing
Route power supply cord so that are not likely to be walked on or pinched by items
placed upon or against them. Pay particular attention to the cords that plugs in the convenience receptacles,
and the point where they exit from the unit.
Use an outlet that contains surge suppression or ground fault protection.
For added protection during a lightning storm, or when the receiver is left unattached
and unused for long periods of time, unplug it from the wall outlet and disconnect
the lines between the receiver and the antenna. This will provide some protection
against electrical damage caused by lightning or power line surges.
Do not attempt to service the receiver yourself, as opening or
removing covers may expose you to dangerous voltage,
and will void warranty.
Refer all servicing to authorized service personnel.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 2 mac-4 HP LaserJet 5100 Series T
DIGITAL SATELLITE RECEIVER
OWNER’S MANUAL
SIMPLE & SPEEDY
OPERATION HANDBOOK
Before operation,
Please read the entire manual thoroughly
and retain it for future reference.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 3 mac-4 HP LaserJet 5100 Series T
Channel Search
Channel List
Edit Channel List
Program Guide
System Setting
Utility (Option)
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 4 mac-4 HP LaserJet 5100 Series T
1
DIGITAL SATELLITE RECEIVER
Contents
Remote Control Unit ...........................................................................
Front Panel ..........................................................................................
Rear Panel ..........................................................................................
Connecting Your Equipment ...............................................................
Basic Operation ..................................................................................
Menu Guide ........................................................................................
Easy Installation .......................................................................................
Main Menu ............................................................................................
Channel Search .......................................................................................
Channel Search / Installation (None, DiSEqC Switch) ...........................................
Channel Search / Installation (DiSEqC 1,2) .......................................................
Channel Search / Installation (USALS) ............................................................
Channel List ...........................................................................................
Edit Channel List ......................................................................................
Program Guide ........................................................................................
System Setting ........................................................................................
Menu Language ....................................................................................
Audio Language ....................................................................................
Subtitle Language ..................................................................................
SCART Output (option) ............................................................................
Screen Type .........................................................................................
Banner Time ........................................................................................
RF Mode (option) ...................................................................................
RF Channel (option) ................................................................................
Local Time ..........................................................................................
3
5
6
7
12
16
16
18
19
19
22
25
28
29
32
33
33
34
34
34
35
35
35
36
36
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 1 mac-4 HP LaserJet 5100 Series T
2
DIGITAL SATELLITE RECEIVER
Contents
Menu Transparency ............................................................................
Change PIN Code ............................................................................
Parental Lock .................................................................................
Receiver Lock .................................................................................
Menu Lock .....................................................................................
Auto Power (option) ...........................................................................
Timer............................................................................................
Factory Reset ..................................................................................
System Information ............................................................................
Utility (option) ....................................................................................
Troubleshooting ................................................................................
Technical Specifications ...................................................................
Menu Map .........................................................................................
36
37
37
38
38
39
39
39
39
40
42
43
45
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 2 mac-4 HP LaserJet 5100 Series T
3
DIGITAL SATELLITE RECEIVER
Remote Control Unit
MUTE To enable or disable audio.
STAND BY To switch between operation and stand by mode.
NUMERIC BUTTONS
To select the channel and enter the channel edit and PIN code .
PAGE DOWN To switch between TV and Radio.
PAGE UP To change picture standard.(Option)
EXIT To change screen size.
RECALL To select the sound mode.(Mono, Left, Right, Stereo)
MENU To change channel up and down.
OK To increase or decrease the volume.
UP/DOWN To select the audio language.
LEFT/RIGHT To return to the previous channel.
EPG To display the TV/Radio program guide.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 3 mac-4 HP LaserJet 5100 Series T
4
DIGITAL SATELLITE RECEIVER
Remote Control Unit
Note! 1: When inserting batteries, make sure that the polarity (+/–) is correct.
Note! 2: The design of the Remote Control Unit may be changed without any
notice in advance.
EPG To display the TV/Radio program guide.
A/LANG To select the audio language
A/LR To select the sound mode.(Mono,Left,Right,Stereo)
GREEN To see the current information Banner guide or the satellite list.
YELLOW To sort channel list.
To display the reserved list.(Option)
SUBTITLE(RED) To enable or disable subtitle or change the channel list mode.
INFO(BLUE) To display the information box on the screen.
TV/STB To switch between TV and STB receive mode.
P.SIZE To change screen size.
P.STD To change picture standard.(Option)
TEXT To see the teletext by OSD.(Option)
TV/RADIO To switch between TV and Radio.
SLEEP To select a present time interval for automatic shut off
FAV. To change/view Favorite channel list.(Option)
PAUSE To pause or play video.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 4 mac-4 HP LaserJet 5100 Series T
5
DIGITAL SATELLITE RECEIVER
Front Panel
1.POWER(STAND BY) Switch the receiver power “ON” or “OFF”.
2.CH Up/Down : Channel Up/Down or select item of sub-menu.
3.SEG. DISP.: 4-digit 7-segment display channel information.
4.Smartcard Slot(Option): 1 shot for smartcard.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 5 mac-4 HP LaserJet 5100 Series T
6
DIGITAL SATELLITE RECEIVER
Rear Panel
1. SCART FOR TV Connect this port to the TV via SCART cable.
2. VIDEO Video connection port to the TV or other equipment.
3. 0/12V To connect 12V to an external 0/12V switch.
4. AUDIO Audio Audio connection port to the TV or other equipment.
5. RF LOOP IN To connect to a general aerial antenna and cable jacks to a
RF input jack on the STB.
6. TV OUT To connect a TV via a coaxial cable.
7. RS-232 To connect to a personal computer for software upgrade.
8. LNB To connect to a satellite antenna and cable jacks.
9. LOOP THROUGH To connect other satellite receiver.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 6 mac-4 HP LaserJet 5100 Series T
7
DIGITAL SATELLITE RECEIVER
Connecting Your Equipment
There are several ways of connecting the STB to your TV, VCR and/or Hi-Fi SYSTEM. Consult your local
supplier for assistance in setting-up your system that is best suited to your requirements.
1. Connect STB to a TV set
Connect your STB to a TV set with SCART, if your TV set is equipped for it.
Alternatively you can use A/V, TV out (UHF) or S/Video jacks.
2. Connect STB to a VCR
Connect the SCART jack from the VCR to the back of your STB.
Alternatively you can use A/V, TV out (UHF) or S/Video jacks.
How to connect your STB to various systems
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 7 mac-4 HP LaserJet 5100 Series T
8
DIGITAL SATELLITE RECEIVER
Connecting Your Equipment
3. Connect STB to a Digital Audio System
If you have a DAC with S/PDIF coaxial cable input, you can connect the STB with it to enjoy
higher quality sound. Connect S/PDIF coaxial cable to a digital amplifier.
4. Loop Through
If you have another analogue or digital STB and you wish to use the same LNB then you can
connect it via the loop through. Connect one end of the coaxial cable to the Loop Through on the
STB and connect the other end to the LNB IN on your second STB.
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 8 mac-4 HP LaserJet 5100 Series T
9
DIGITAL SATELLITE RECEIVER
Connecting Your Equipment
1. Connect one end of RCA/Cinch cable to
the RCA/Cinch jack on the back of the STB
and the other end to a RCA/Cinch jack on
your TV.
If your TV doesn’t have a RCA/Cinch jack,
connect one end of RF cable to the TV OUT
on the back of the STB and the other end to
a RF input jack on your TV.
2. Connect one end of RF cable to the ANT IN
on the back of the STB and the other end to a
terrestrial antenna connection or the jack for
the public antenna on the wall.
3. Finally connect the coaxial cable from the LNB to the LNB IN jack on back of the STB.
1. Connect one end of RCA/Cinch cable to the
RCA/Cinch jack on the back of the STB and
the other end to a RCA/Cinch jack on your TV.
If your TV doesn’t have a RCA/Cinch jack,
connect one end of RF cable to the TV OUT
on the back of the STB and the other end to a
RF input jack on your TV.
2. Connect one end of your coaxial cable to
the LNB IN connector on the STB and
the other end to the REC or Receiver
connector on the DiSEqC 1.2 motor.
3. Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1.2 motor.
(To RCA/Cinch on your TV)
(To RCA/Cinch on your TV)
(If your TV doesn’t have RCA/ Cinch Jack)
(If your TV doesn’t RCA / Cinch Jack)
TV with Terrestrial Antenna
TV with Motorized System (DiSEqC 1.2)
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 9 mac-4 HP LaserJet 5100 Series T
10
DIGITAL SATELLITE RECEIVER
Connecting Your Equipment
1. DiSEqC 1.0 Connection
All our receivers are designed to be DiSEqC 1.0 and DiSEqC 1.2 compatible.
This allows multiple antennas to be connected to the STB at the same time.
If you have two or more fixed antennas or LNBs then we recommend you use a DiSEqC 1.0 switch.
Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC switch.
Do the same for any other LNBs that you have.
Connect one end of a coaxial cable to the RF output connector of the DiSEqC switch,
connect the other end to the LNB IN socket on the STB.
2. DiSEqC 1.2/ USALS Connection
To the digital receiver, you can connect either a single satellite antenna directly or LNB of multi-feed
equipment.
When installing the USALS please consult and receive assistance from an installation specialist,
or ensure that the 0-degree angle of the motor is facing due south when installing,
for proper operation.
Reference
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 10 mac-4 HP LaserJet 5100 Series T
11
DIGITAL SATELLITE RECEIVER
Connecting Your Equipment
KEY & DISPLAY The message of the 7-segment LED (Light-Emitting Diode) on the STB
and keys are explained as below.
Standby Mode Current Program Number on TV List
System Booting Current Program Number on Radio Location
Power Off TV Mode
MICOM Version STB Mode
Upgrade
Boot Loader Version
Upgrade Procedure
Download
Upgrade Complete
Down Load Procedure
Front Panel Display Message
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 11 mac-4 HP LaserJet 5100 Series T
12
DIGITAL SATELLITE RECEIVER
Basic Operation
1. Program Information
After the television channels have been programmed, you will
see the information box each time you change the channels.
1. Every time you change channels you will receive program information for a
few seconds. (In the “Banner Time” menu you can select how long this
information will be shown.)
2. You may change channel lists with the UP or DOWN button.
You can get “Channel Banner” on the bottom of the screen.
3. When you press the COLOR button, you can use banner as a simple channel
operation. In this case, you can get a simple EPG on right view.
2. Favorite Banner
1. During “Channel Banner” is appearing, when you press SUB-T(RED)
Button, you can get “Favorite Banner” and “Lock Banner”.
2. If you already made your favorite channel in “Channel Control” menu,
you can get favorite channel on this view.
3. The banner will disappeared automatically after banner-time out.
3. Now-Information Banner
1. During “Channel Banner” is appearing, when you press GREEN
Button, you can get “Now-Information Banner”.
2. Using “Now-Information Banner”, you can get a simple EPG of
Now-Information”.
Basic Function
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 12 mac-4 HP LaserJet 5100 Series T
13
DIGITAL SATELLITE RECEIVER
Basic Operation
4. Next-Information Banner
1. During “Channel Banner” is appearing, when you press YELLOW Button,
you can get “Next-Information Banner
2. Using “Next-Information Banner”, you can get a simple EPG of
Next-Information”.
5. Channel-Information Banner
1. During “Channel Banner” is appearing, when you press INFO(BLUE) Button,
you can get “Channel-Information Banner”.
2. Using “Channel-Information Banner”, you can get a detailed channel listing
information.
6. Volume Control/Mute
1. To control audio volume, press Volume / Volume buttons.
2. Volume control bar will be appeared in bottom of the TV screen
3. After time-out in 1 second, volume control bar will disappear.
To temporarily stop the volume, press the MUTE button.
To cancel mute, press the MUTE button again or press
the Volume / Volume buttons.
Basic Function
ENGLISH
060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 13 mac-4 HP LaserJet 5100 Series T
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212

Schwaiger DSR 1004 CW Manuale utente

Categoria
Set-top box TV
Tipo
Manuale utente