Schwaiger DSR 1004 CW Manuale utente

Digital Satellite Receiver

User's Manual

DSR 1004 CW

Cryptoworks embedded

GB

D

S

I

060615_K7_KSF-200CX_Schwaiger_Sa3 3 2006-06-15 오후 7:09:17

060615_K7_KSF-200CX_Schwaiger_Sa13 13 2006-06-15 오후 7:20:04

COVER_ENG

Digital Satellite Receiver

User's Manual

Distributed by SCHWAIGER GmbH

Würzburger Str. 17

90579 Langenzenn

-Germany-

Tel Hotline +49

(

0

)

9101 702 299

www.schwaiger.ed

info@schwaiger.ed

DSR 1004 CW

Cryptoworks embedded

GB

060615_K7_KSF-200CX_Schwaiger_Sa5 5 2006-06-15 오후 7:08:47

General Safety

Warning

Always follow these instructions to avoid the risk of injury to

yourself or damage to your equipment.

Unplug the receiver from the AC power outlet before cleaning.

Use only a damp cloth for cleaning the exterior of the receiver.

Do not use accessories or attachments not recommended by the receiver manufacturer

as they may cause problems to the equipment and will void the warranty.

Do not place the receiver on an unstable cart, stand, tripod, bracket, or table.

The receiver may fall, causing serious personal injury and damage to the receiver.

Do not block or cover the slot opening in the receiver.

These are provided for ventilation and protection from overheating.

Never place the receiver near or over a radiator or any heat source.

Do not place the receiver in an enclosure such as a cabinet without proper ventilation

Do not stack the receiver on top of or below other electronic devices.

The apparatus shall not be exposed to dripping or splashing and with no object filled with liquids,

such as vases, shall be placed on the apparatus.

Operate the receiver using only the type of power source indicated on the marking label.

Unplug the receiver power cord by gripping the power plug, not the cord.

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 1 mac-4 HP LaserJet 5100 Series T

General Safety

Servicing

Route power supply cord so that are not likely to be walked on or pinched by items

placed upon or against them. Pay particular attention to the cords that plugs in the convenience receptacles,

and the point where they exit from the unit.

Use an outlet that contains surge suppression or ground fault protection.

For added protection during a lightning storm, or when the receiver is left unattached

and unused for long periods of time, unplug it from the wall outlet and disconnect

the lines between the receiver and the antenna. This will provide some protection

against electrical damage caused by lightning or power line surges.

Do not attempt to service the receiver yourself, as opening or

removing covers may expose you to dangerous voltage,

and will void warranty.

Refer all servicing to authorized service personnel.

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 2 mac-4 HP LaserJet 5100 Series T

DIGITAL SATELLITE RECEIVER

OWNER’S MANUAL

SIMPLE & SPEEDY

OPERATION HANDBOOK

Before operation,

Please read the entire manual thoroughly

and retain it for future reference.

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 3 mac-4 HP LaserJet 5100 Series T

Channel Search

Channel List

Edit Channel List

Program Guide

System Setting

Utility (Option)

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 4 mac-4 HP LaserJet 5100 Series T

1

DIGITAL SATELLITE RECEIVER

Contents

Remote Control Unit ...........................................................................

Front Panel ..........................................................................................

Rear Panel ..........................................................................................

Connecting Your Equipment ...............................................................

Basic Operation ..................................................................................

Menu Guide ........................................................................................

Easy Installation .......................................................................................

Main Menu ............................................................................................

Channel Search .......................................................................................

Channel Search / Installation (None, DiSEqC Switch) ...........................................

Channel Search / Installation (DiSEqC 1,2) .......................................................

Channel Search / Installation (USALS) ............................................................

Channel List ...........................................................................................

Edit Channel List ......................................................................................

Program Guide ........................................................................................

System Setting ........................................................................................

Menu Language ....................................................................................

Audio Language ....................................................................................

Subtitle Language ..................................................................................

SCART Output (option) ............................................................................

Screen Type .........................................................................................

Banner Time ........................................................................................

RF Mode (option) ...................................................................................

RF Channel (option) ................................................................................

Local Time ..........................................................................................

3

5

6

7

12

16

18

19

22

25

28

29

32

33

34

35

36

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 1 mac-4 HP LaserJet 5100 Series T

2

DIGITAL SATELLITE RECEIVER

Contents

Menu Transparency ............................................................................

Change PIN Code ............................................................................

Parental Lock .................................................................................

Receiver Lock .................................................................................

Menu Lock .....................................................................................

Auto Power (option) ...........................................................................

Timer............................................................................................

Factory Reset ..................................................................................

System Information ............................................................................

Utility (option) ....................................................................................

Troubleshooting ................................................................................

Technical Specifications ...................................................................

Menu Map .........................................................................................

36

37

38

39

40

42

43

45

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 2 mac-4 HP LaserJet 5100 Series T

3

DIGITAL SATELLITE RECEIVER

Remote Control Unit

MUTE To enable or disable audio.

STAND BY To switch between operation and stand by mode.

NUMERIC BUTTONS

To select the channel and enter the channel edit and PIN code .

PAGE DOWN To switch between TV and Radio.

PAGE UP To change picture standard.(Option)

EXIT To change screen size.

RECALL To select the sound mode.(Mono, Left, Right, Stereo)

MENU To change channel up and down.

OK To increase or decrease the volume.

UP/DOWN To select the audio language.

LEFT/RIGHT To return to the previous channel.

EPG To display the TV/Radio program guide.

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 3 mac-4 HP LaserJet 5100 Series T

4

DIGITAL SATELLITE RECEIVER

Remote Control Unit

Note! 1: When inserting batteries, make sure that the polarity (+/–) is correct.

Note! 2: The design of the Remote Control Unit may be changed without any

notice in advance.

EPG To display the TV/Radio program guide.

A/LANG To select the audio language

A/LR To select the sound mode.(Mono,Left,Right,Stereo)

GREEN To see the current information Banner guide or the satellite list.

YELLOW To sort channel list.

To display the reserved list.(Option)

SUBTITLE(RED) To enable or disable subtitle or change the channel list mode.

INFO(BLUE) To display the information box on the screen.

TV/STB To switch between TV and STB receive mode.

P.SIZE To change screen size.

P.STD To change picture standard.(Option)

TEXT To see the teletext by OSD.(Option)

TV/RADIO To switch between TV and Radio.

SLEEP To select a present time interval for automatic shut off

FAV. To change/view Favorite channel list.(Option)

PAUSE To pause or play video.

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 4 mac-4 HP LaserJet 5100 Series T

5

DIGITAL SATELLITE RECEIVER

Front Panel

1.POWER(STAND BY) Switch the receiver power “ON” or “OFF”.

2.CH Up/Down : Channel Up/Down or select item of sub-menu.

3.SEG. DISP.: 4-digit 7-segment display channel information.

4.Smartcard Slot(Option): 1 shot for smartcard.

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 5 mac-4 HP LaserJet 5100 Series T

6

DIGITAL SATELLITE RECEIVER

Rear Panel

1. SCART FOR TV Connect this port to the TV via SCART cable.

2. VIDEO Video connection port to the TV or other equipment.

3. 0/12V To connect 12V to an external 0/12V switch.

4. AUDIO Audio Audio connection port to the TV or other equipment.

5. RF LOOP IN To connect to a general aerial antenna and cable jacks to a

RF input jack on the STB.

6. TV OUT To connect a TV via a coaxial cable.

7. RS-232 To connect to a personal computer for software upgrade.

8. LNB To connect to a satellite antenna and cable jacks.

9. LOOP THROUGH To connect other satellite receiver.

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 6 mac-4 HP LaserJet 5100 Series T

7

DIGITAL SATELLITE RECEIVER

Connecting Your Equipment

There are several ways of connecting the STB to your TV, VCR and/or Hi-Fi SYSTEM. Consult your local

supplier for assistance in setting-up your system that is best suited to your requirements.

1. Connect STB to a TV set

Connect your STB to a TV set with SCART, if your TV set is equipped for it.

Alternatively you can use A/V, TV out (UHF) or S/Video jacks.

2. Connect STB to a VCR

Connect the SCART jack from the VCR to the back of your STB.

Alternatively you can use A/V, TV out (UHF) or S/Video jacks.

How to connect your STB to various systems

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 7 mac-4 HP LaserJet 5100 Series T

8

DIGITAL SATELLITE RECEIVER

Connecting Your Equipment

3. Connect STB to a Digital Audio System

If you have a DAC with S/PDIF coaxial cable input, you can connect the STB with it to enjoy

higher quality sound. Connect S/PDIF coaxial cable to a digital amplifier.

4. Loop Through

If you have another analogue or digital STB and you wish to use the same LNB then you can

connect it via the loop through. Connect one end of the coaxial cable to the Loop Through on the

STB and connect the other end to the LNB IN on your second STB.

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 8 mac-4 HP LaserJet 5100 Series T

9

DIGITAL SATELLITE RECEIVER

Connecting Your Equipment

1. Connect one end of RCA/Cinch cable to

the RCA/Cinch jack on the back of the STB

and the other end to a RCA/Cinch jack on

your TV.

If your TV doesn’t have a RCA/Cinch jack,

connect one end of RF cable to the TV OUT

on the back of the STB and the other end to

a RF input jack on your TV.

2. Connect one end of RF cable to the ANT IN

on the back of the STB and the other end to a

terrestrial antenna connection or the jack for

the public antenna on the wall.

3. Finally connect the coaxial cable from the LNB to the LNB IN jack on back of the STB.

1. Connect one end of RCA/Cinch cable to the

RCA/Cinch jack on the back of the STB and

the other end to a RCA/Cinch jack on your TV.

If your TV doesn’t have a RCA/Cinch jack,

connect one end of RF cable to the TV OUT

on the back of the STB and the other end to a

RF input jack on your TV.

2. Connect one end of your coaxial cable to

the LNB IN connector on the STB and

the other end to the REC or Receiver

connector on the DiSEqC 1.2 motor.

3. Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1.2 motor.

(To RCA/Cinch on your TV)

(If your TV doesn’t have RCA/ Cinch Jack)

(If your TV doesn’t RCA / Cinch Jack)

TV with Terrestrial Antenna

TV with Motorized System (DiSEqC 1.2)

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 9 mac-4 HP LaserJet 5100 Series T

10

DIGITAL SATELLITE RECEIVER

Connecting Your Equipment

1. DiSEqC 1.0 Connection

All our receivers are designed to be DiSEqC 1.0 and DiSEqC 1.2 compatible.

This allows multiple antennas to be connected to the STB at the same time.

If you have two or more fixed antennas or LNBs then we recommend you use a DiSEqC 1.0 switch.

Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC switch.

Do the same for any other LNBs that you have.

Connect one end of a coaxial cable to the RF output connector of the DiSEqC switch,

connect the other end to the LNB IN socket on the STB.

2. DiSEqC 1.2/ USALS Connection

To the digital receiver, you can connect either a single satellite antenna directly or LNB of multi-feed

equipment.

When installing the USALS please consult and receive assistance from an installation specialist,

or ensure that the 0-degree angle of the motor is facing due south when installing,

for proper operation.

Reference

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 10 mac-4 HP LaserJet 5100 Series T

11

DIGITAL SATELLITE RECEIVER

Connecting Your Equipment

KEY & DISPLAY The message of the 7-segment LED (Light-Emitting Diode) on the STB

and keys are explained as below.

Standby Mode Current Program Number on TV List

System Booting Current Program Number on Radio Location

Power Off TV Mode

MICOM Version STB Mode

Upgrade

Boot Loader Version

Upgrade Procedure

Download

Upgrade Complete

Down Load Procedure

Front Panel Display Message

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 11 mac-4 HP LaserJet 5100 Series T

12

DIGITAL SATELLITE RECEIVER

Basic Operation

1. Program Information

After the television channels have been programmed, you will

see the information box each time you change the channels.

1. Every time you change channels you will receive program information for a

few seconds. (In the “Banner Time” menu you can select how long this

information will be shown.)

2. You may change channel lists with the UP or DOWN button.

You can get “Channel Banner” on the bottom of the screen.

3. When you press the COLOR button, you can use banner as a simple channel

operation. In this case, you can get a simple EPG on right view.

2. Favorite Banner

1. During “Channel Banner” is appearing, when you press SUB-T(RED)

Button, you can get “Favorite Banner” and “Lock Banner”.

2. If you already made your favorite channel in “Channel Control” menu,

you can get favorite channel on this view.

3. The banner will disappeared automatically after banner-time out.

3. Now-Information Banner

1. During “Channel Banner” is appearing, when you press GREEN

Button, you can get “Now-Information Banner”.

2. Using “Now-Information Banner”, you can get a simple EPG of

“Now-Information”.

Basic Function

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 12 mac-4 HP LaserJet 5100 Series T

13

DIGITAL SATELLITE RECEIVER

Basic Operation

4. Next-Information Banner

1. During “Channel Banner” is appearing, when you press YELLOW Button,

you can get “Next-Information Banner”

2. Using “Next-Information Banner”, you can get a simple EPG of

“Next-Information”.

5. Channel-Information Banner

1. During “Channel Banner” is appearing, when you press INFO(BLUE) Button,

you can get “Channel-Information Banner”.

2. Using “Channel-Information Banner”, you can get a detailed channel listing

information.

6. Volume Control/Mute

1. To control audio volume, press Volume / Volume buttons.

2. Volume control bar will be appeared in bottom of the TV screen

3. After time-out in 1 second, volume control bar will disappear.

To temporarily stop the volume, press the MUTE button.

To cancel mute, press the MUTE button again or press

the Volume / Volume buttons.

Basic Function

ENGLISH

060615_k7 200 ENG sat_shw 6/15/06 6:01 AM ˘ ` 13 mac-4 HP LaserJet 5100 Series T

La pagina sta caricando ...

Schwaiger DSR 1004 CW Manuale utente

Schwaiger DSR 1004 CW Manuale utente

in altre lingue

Documenti correlati

Altri documenti