ASROCK 775TWINS-HDTV Manuale del proprietario

11

1

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published December 2005

22

2

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PWR1 Jumper 17 Chassis Fan Connector (CHA_FAN1)

2 ATX 12V Connector (ATX12V1) 18 System Panel Header (PANEL1)

3 775-Pin CPU Socket 19 Chassis Speaker Header (SPEAKER 1)

4 North Bridge Controller 20 USB 2.0 Header (USB45, Blue)

5 CPU Fan Connector (CPU_FAN1) 21 USB 2.0 Header (USB67, Blue)

6 2 x 240-pin DDRII DIMM Slots 22 Clear CMOS Jumper (CLRCMOS1)

(DDRII_1, DDRII_2; Yellow) 23 Floppy Connector (FLOPPY1)

7 2 x 184-pin DDR DIMM Slots 24 Game Port Header (GAME1)

(DDR1, DDR2; Blue) 25 Infrared Module Connector (IR1)

8 Primary IDE Connector (IDE1, Blue) 26 AMR Slot (AMR1)

9 Secondary IDE Connector (IDE2, Black) 27 Front Panel Audio Header (AUDIO1)

10 PCI EXPRESS Slot (PCIE1) 28 JR1 / JL1 Jumpers

11 BIOS FWH Chip 29 PCI EXPRESS Slot (PCIE2)

12 South Bridge Controller 30 PCI Slots (PCI1- 2)

13 Fourth Serial ATA Connector (SATA4, black) 31 TV-OUT Connector (TV-OUT1)

14 Third Serial ATA Connector (SATA3, black) 32 VGA Connector (VGA1)

15 Secondary Serial ATA Connector (SATA2, black) 33 Internal Audio Connector: CD1 (Black)

16 Primary Serial ATA Connector (SATA1, blue) 34 ATX Power Connector (ATXPWR1)

33

3

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

ASRock 8CH I/OASRock 8CH I/O

ASRock 8CH I/O

1 Parallel Port 8 Microphone (Pink)

2 RJ-45 Port 9 USB 2.0 Ports (USB01)

3 Side Speaker (Gray) 10 USB 2.0 Ports (USB23)

4 Rear Speaker (Black) 11 Serial Port: COM1

5 Central / Bass (Orange) 12 PS/2 Keyboard Port (Purple)

6 Line In (Light Blue) 13 PS/2 Mouse Port (Green)

*7 Front Speaker (Lime)

* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See

the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker

(No. 7) (No. 4) (No. 5) (No. 3)

2 V -- -- --

4VV----

6 VVV--

8 VVVV

44

4

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

1. Introduction1. Introduction

1. Introduction

Thank you for purchasing ASRock 775Twins-HDTV motherboard, a reliable mother-

board produced under ASRock’s consistently stringent quality control. It delivers

excellent performance with robust design conforming to ASRock’s commitment to

quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change

without notice. In case any modifications of this manual occur, the

updated version will be available on ASRock website without further

notice. You may find the latest memory and CPU support lists on

ASRock website as well.

ASRock website

http://www.asrock.com

1.1 Package Contents1.1 Package Contents

1.1 Package Contents

ASRock 775Twins-HDTV Motherboard

(Micro ATX Form Factor: 9.6-in x 9.6-in, 24.4 cm x 24.4 cm)

ASRock 775Twins-HDTV Quick Installation Guide

ASRock 775Twins-HDTV Support CD

(including LGA 775 CPU Installation Live Demo)

One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

One Serial ATA (SATA) Data Cable (Optional)

One Serial ATA (SATA) HDD Power Cable (Optional)

One ASRock 8CH I/O

One ASRock MR Card (Optional)

One ASRock VGA_HDTV Panel

One VGA_2x8 Cable

One AV/S_2x3 Cable

55

5

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - Micro ATX Form Factor: 9.6-in x 9.6-in, 24.4 cm x 24.4 cm

CPU - 775-Pin Socket supporting Intel

®

Dual Core Pentium

®

XE and

Pentium

®

D / Pentium

®

4 / Celeron

®

D processor

(in 775-land LGA package)

- FSB 1066/800/533 MHz

- Supports EM64T CPU

- Supports Hyper-Threading Technology (see CAUTION 1)

- Supports Untied Overclocking Technology (see CAUTION 2)

Chipset - Northbridge: ATI

TM

Radeon

®

Xpress 200 chipset

- Southbridge: ULi

®

1573

Memory - 2 x DDR DIMM slots

- Support DDR400/333/266

- Max. capacity: 4GB

- 2 x DDRII DIMM slots

- Support DDRII667/533/400

- Max. capacity: 4GB

Hybrid Booster - CPU Frequency Stepless Control (see CAUTION 3)

- ASRock U-COP (see CAUTION 4)

- Boot Failure Guard (B.F.G.)

Expansion Slot - 2 x PCI slots

- 1 x PCI Express x 16 slot

- 1 x PCI Express x 1 slot

- 1 x AMR slot

Graphics - Integrated ATI

TM

Radeon

®

X300 based graphics

- DirectX 9.0 VGA

- Pixel Shader 2.0

- Max. shared memory 128MB

Audio - Realtek ALC850 7.1 channel AC’97 audio codec

LAN - Realtek PHY RTL8201CL

- Speed: 10/100Mb Ethernet

- Supports Wake-On-LAN

Rear Panel I/O ASRock 8CH I/O

- 1 x PS/2 Mouse

- 1 x PS/2 Keyboard Port

- 1 x Serial Port: COM1

- 1 x Parallel Port (ECP/EPP Support)

- 4 x Ready-to-Use USB 2.0 Ports

66

6

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

- 1 x RJ-45 Port

- Audio Jack: Side Speaker/Rear Speaker/Central Bass/Line

in/Front Speaker/Microphone (see CAUTION 5)

Connector - 4 x Serial ATA 1.5Gb/s connectors

(Supports RAID 0, 1, JBOD)

(No support for “Hot Plug” function)

- 2 x ATA133 IDE connector (supports 4 x IDE devices)

- 1 x Floppy connector

- 1 x Game header

- 1 x IR header

- 1 x VGA header

- 1 x TV-OUT header

- CPU/Chassis FAN connector

- 20 pin ATX power connector

- 4 pin 12V power connector

- CD in header

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

(see CAUTION 6)

BIOS Feature - 4Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- SMBIOS 2.3.1 Support

Support CD - Drivers, Utilities, AntiVirus Software

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU Overheat Shutdown to Protect CPU Life

- CPU Fan Tachometer

- Chassis Fan Tachometer

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft

®

Windows

®

2000/XP/XP 64-bit compliant

Certifications - FCC, CE, WHQL

77

7

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

CAUTION!

1. About the setting of “Hyper Threading Technology”, please check page 30

of “User Manual” in the support CD.

2. This motherboard supports Untied Overclocking Technology. Please read “Un-

tied Overclocking Technology” on page 21 for details.

3. Although this motherboard offers stepless control, it is not recommended

to perform over-clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU.

4. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

5. For microphone input, this motherboard supports both stereo and mono

modes. For audio output, this motherboard supports 2-channel, 4-channel,

6-channel, and 8-channel modes. Please check the table on page 3 for

proper connection.

6. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

XP

SP1 or SP2 / 2000 SP4.

88

8

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet

or the like. Also remember to use a grounded wrist strap or touch

a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded

antstatic pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the

screws! Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

For the installation of Intel 775-LAND CPU,

please follow the steps below.

Before you insert the 775-LAND CPU into the socket, please check if

the CPU surface is unclean or if there is any bent pin on the socket.

Do not force to insert the CPU into the socket if above situation is

found. Otherwise, the CPU will be seriously damaged.

775-Pin Socket Overview

99

9

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing

down and out on the hook to clear

retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open po-

sition at approximately 100 degrees.

Step 2. Insert the 775-LAND CPU:

Step 2-1. Hold the CPU by the edges where are

marked with black lines.

Step 2-2. Orient the CPU with IHS (Integrated

Heat Sink) up. Locate Pin1 and the two

orientation key notches.

For proper inserting, please ensure to match the two orientation key

notches of the CPU with the two alignment keys of the socket.

Step 2-3. Carefully place the CPU into the socket

by using a purely vertical motion.

Step 2-4. Verify that the CPU is within the socket

and properly mated to the orient keys.

Step 3. Remove PnP Cap (Pick and Place Cap):

Use your left hand index finger and thumb to

support the load plate edge, engage PnP cap

with right hand thumb and peel the cap from the

socket while pressing on center of PnP cap to

assist in removal.

black line

775-Pin Socket

Pin1

alignment key

Pin1

orientation

key notch

orientation

key notch

775-LAND CPU

1010

10

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

1. It is recommended to use the cap tab to handle and avoid kicking

off the PnP cap.

2. This cap must be placed if returning the motherboard for after

service.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS.

Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab

under retention tab of load lever.

2.22.2

2.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

Installation of CPU Fan and Heatsink

For proper installation, please kindly refer to the instruction manuals of your CPU fan

and heatsink.

Below is an example to illustrate the installation of the heatsink for 775-LAND CPU.

Step 1. Apply thermal interface material onto center

of IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure

fan cables are oriented on side closest to the

CPU fan connector on the motherboard

(CPU_FAN1, see page 2, No. 5).

Step 3. Align fasteners with the motherboard

throughholes.

Step 4. Rotate the fastener clockwise, then press

down on fastener caps with thumb to install

and lock. Repeat with remaining fasteners.

If you press down the fasteners without rotating them clockwise, the heatsink cannot be

secured on the motherboard.

Step 5. Connect fan header with the CPU fan

connector on the motherboard.

Step 6. Secure excess cable with tie-wrap to ensure

cable does not interfere with fan operation or

contact other components.

1111

11

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

2.32.3

2.3

Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)

Installation of Memory Modules (DIMM)

This motherboard is equipped with two 184-pin DDR (Double Data Rate) DIMM slots

and two 240-pin DDRII (Double Data Rate) DIMM slots.

1. It is not allowed to install DDR into DDRII slot or DDRII into DDR

slot;otherwise, this motherboard and DIMM may be damaged.

2. It is not allowed to install both DDR and DDRII to this motherboard

at the same time; otherwise, this motherboard and DIMM may be

damaged.

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into

the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

1212

12

ASRock 775Twins-HDTV Motherboard

2.6 Jumpers Setup2.6 Jumpers Setup

2.6 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

EnglishEnglish

English

2.4 Expansion Slots (PCI, AMR, and PCI Express Slots)2.4 Expansion Slots (PCI, AMR, and PCI Express Slots)

2.4 Expansion Slots (PCI, AMR, and PCI Express Slots)

There are 2 PCI slots, 1 AMR slot and 2 PCI Express slot on this motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

AMR slot: AMR slot is used to insert an ASRock MR card (optional) with v.92

Modem functionality.

PCIE Slots: PCIE1 (PCIE x16 slot) is used for PCI Express cards with x16 lane

width graphics cards.

PCIE2 (PCIE x1 slot) is used for PCI Express cards, such as

Gigabit LAN card, SATA2 card, etc.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in

a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

Short Open

2.5 Easy Multi Monitor Feature2.5 Easy Multi Monitor Feature

2.5 Easy Multi Monitor Feature

This motherboard supports Multi Monitor upgrade. With the onboard VGA and the

external add-on PCI Express VGA card, you can easily enjoy the benefits of Multi

Monitor Feature. If you plan to enable the function of onboard VGA, please select

the option “Primary Graphics Adapter” of BIOS to [Onboard], and then install VGA

card and VGA card drivers to enjoy multi-monitors.

1313

13

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

Clear CMOSDefault

JR1(see p.2 No. 28)

JL1(see p.2 No. 28)

Note: If the jumpers JL1 and JR1 are short, both the front panel and the rear panel

audio connectors can work.

Clear CMOS

(CLRCMOS1, 3-pin jumper)

(see p.2 No. 22)

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3

on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right

after you update the BIOS. If you need to clear the CMOS when you just finish

updating the BIOS, you must boot up the system first, and then shut it down

before you do the clear-CMOS action.

2.7 Onboard Headers and Connectors2.7 Onboard Headers and Connectors

2.7 Onboard Headers and Connectors

FDD connector

(33-pin FLOPPY1)

(see p.2 No. 23)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE Connector (Blue) Secondary IDE Connector (Black)

(39-pin IDE1, see p.2, No. 8) (39-pin IDE2, see p.2, No. 9)

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

the red-striped side to Pin1

connect the black end

to the IDE devices

Jumper Setting Description

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2 No. 1) +5VSB (standby) for PS/2

or USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

1414

14

ASRock 775Twins-HDTV Motherboard

connect to the

power supply

connect to the SATA

HDD power connector

EnglishEnglish

English

Serial ATA Connectors These four Serial ATA (SATA)

(SATA1: see p.2 No. 16) connectors support SATA data

(SATA2: see p.2 No. 15) cables for internal storage

(SATA3: see p.2 No. 14) devices. The current SATA

(SATA4: see p.2 No. 13) interface allows up to 1.5 Gb/s

data transfer rate.

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA

hard disk or the SATA connector

on the motherboard.

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

SATA1

SATA2

SATA3

SATA4

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor

for the details. Besides, to optimize compatibility and performance, please

connect your hard disk drive to the primary IDE connector (IDE1, blue) and

CD-ROM to the secondary IDE connector (IDE2, black).

VGA_2x8 Cable Please connect either end of

VGA_2X8 cable to J1 jumper of

VGA_HDTV panel and the other

end to VGA1 header of this

motherboard.

AV/S_2x3 Cable Please connect either end of

AV/S_2x3 cable to J2 jumper of

VGA_HDTV panel and the other

end to TV-OUT header of this

motherboard.

VGA Header Please connect either end of

(VGA1: see p.2 No. 32) VGA_2X8 cable to VGA header.

1515

15

ASRock 775Twins-HDTV Motherboard

CD1

USB 2.0 Header ASRock 8CH I/O accommo-

(9-pin USB67) dates 4 default USB 2.0 ports. If

(see p.2 No. 21) those USB 2.0 ports on the I/O

panel are not sufficient, this

USB 2.0 header is available to

support 2 additional USB 2.0

ports.

USB 2.0 Header ASRock 8CH I/O accommo-

(9-pin USB45) dates 4 default USB 2.0 ports. If

(see p.2 No. 20) those USB 2.0 ports on the I/O

panel are not sufficient, this

USB 2.0 header is available to

support 2 additional USB 2.0

ports.

Infrared Module Header This header supports an

(5-pin IR1) optional wireless transmitting

(see p.2 No. 25) and receiving infrared module.

Internal Audio Connectors This connector allows you

(4-pin CD1) to receive stereo audio input

(CD1: see p.2 No. 33) from sound sources such as

a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

Front Panel Audio Header This is an interface for front

(9-pin AUDIO1) panel audio cable that allows

(see p.2 No. 27) convenient connection and

control of audio devices.

EnglishEnglish

English

TV-OUT Header Please connect either end of

(TV-OUT1: see p.2 No. 31) AV/S_2X3 cable to TV-OUT

header.

1616

16

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel

(see p.2 No. 18) functions.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1) speaker to this header.

(see p.2 No. 19)

Chassis Fan Connector Please connect a chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2 No. 17) match the black wire to the

ground pin.

CPU Fan Connector Please connect a CPU fan cable

(3-pin CPU_FAN1) to this connector and match

(see p.2 No. 5) the black wire to the ground pin.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2 No. 34)

ATX 12V Connector Please connect an ATX 12V

(4-pin ATX12V1) power supply to this connector.

(see p.2 No. 2)

Game Port Header Connect a Game cable to this

(15-pin GAME1) header if the Game port bracket

(see p.2 No. 24) is installed.

1717

17

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

2.82.8

2.8

Installing VGA_HDTV Panel to Enjoy HDTV (High-Installing VGA_HDTV Panel to Enjoy HDTV (High-

Installing VGA_HDTV Panel to Enjoy HDTV (High-

Definition TV) / TV Support FunctionDefinition TV) / TV Support Function

Definition TV) / TV Support Function

Additional VGA_HDTV panel with VGA and 3 RCA-type component video output, that

allows PC to connect to all high-definition TV with component video input capability

(YPbPr) or TV with AV input capability.

ASRock VGA_HDTV Layout

1 Y-CON1: RCA-type component video connector (green)

2 PB-CON1: RCA-type component video connector (blue) /

AV (composite) signal connector

3 PR-CON1: RCA-type component video connector (red)

4 VGA1: 25pin D-Sub (blue) for VGA monitor

5 J2 header

6 J1 header

Installing VGA_HDTV Panel

Step 1. Either end of the VGA_2X8 cable can be connected to the J1 jumper of

VGA_HDTV panel or the VGA1 header of this motherboard.

Step 2. Either end of the AV/S_2X3 cable can be connected to the J2 jumper of

VGA_HDTV panel or the TV-OUT header of this motherboard.

Step 3. Connect the output connectors to all high-definition TV with component video

input capability (YPbPr) or TV with AV input capability.

Step 4. Secure the VGA_HDTV panel with the bracket to the chassis.

1. You must have a monitor attached to your computer to install the VGA

driver correctly in advance.

2. After installing the VGA driver to the computer, this motherboard supports

static “Auto Sensing” feature. That is, if you install the stand alone

HDTV, TV, or VGA monitor before your computer boots, the system can

display correctly on the output device you use. Therefore, if you only

install HDTV or TV instead of VGA monitor, it is not necessary for you to

enable the TV display setting in Windows control panel or change BIOS

setup, and you can enjoy the HDTV or TV display function directly.

1818

18

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

Male/Male RCA Patch Cables -

available from consumer

electronics dealer

For maximum performance when you watch DVD movies or play

computer games on your HDTV, you should find the mode and screen

resolution that provide the best result on your TV, and use those settings

exclusively.

Typical HDTV Video

Input Connectors

2.8.1 HDTV (High-Definition TV) Support Function2.8.1 HDTV (High-Definition TV) Support Function

2.8.1 HDTV (High-Definition TV) Support Function

View computer output directly on your High Definition Television (HDTV) or other

devices with component video input capability. Provide a big-screen experience

for your computer that is ideal for playing games, giving presentations, watching

movies, and browsing the Internet.

HDTV uses YPbPr connectors to receive input. The HDTV Component Video

Adapter can be used in place of the standard AV Output cable to connect to an

HDTV or other component video input devices, using component video cables.

Connecting to HDTV With Component Video (YPbPr) OutputConnecting to HDTV With Component Video (YPbPr) Output

Connecting to HDTV With Component Video (YPbPr) Output

CapabilityCapability

Capability

Step 1. Connect the Male/Male RCA patch cables to the Typical HDTV component

Video Input connectors and the RCA-type component video connectors

(Y-CON1, PB-CON1, and PR-CON1) (Y-CON1, see page 17, No. 1; PB-

CON1, see page 17, No. 2; PR-CON1, see page 17, No. 3) of the

VGA_HDTV panel.

Please correctly connect the Male/Male RCA patch cables to both HDTV Video

Input connectors and RCA-type component video connectors according to

the functions of the connectors distinguished by the same color (green, blue,

and red). For example, you need to connect the red Male/Male RCA patch

cable to the red port (PR) of HDTV and the red port (PR-CON1) of VGA_HDTV

panel. Please see your HDTV and Male/Male RCA patch cables manuals for

configuration information specific to your device.

Step 2. Turn on your computer and wait system to boot into OS.

Step 3. Change HDTV display settings.

1919

19

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

V

t

Connecting to VGA Monitor and HDTV With ComponentConnecting to VGA Monitor and HDTV With Component

Connecting to VGA Monitor and HDTV With Component

Video (YPbPr) Output CapabilityVideo (YPbPr) Output Capability

Video (YPbPr) Output Capability

When you install both VGA monitor cable and Male/Male RCA patch cables to

VGA_HDTV panel at the same time, the default enabled screen is the VGA monitor.

You are able to switch the monitor display to HDTV display by following the below

instruction.

Step 1. Connect one end of the VGA monitor cable to your monitor, and the other

end to the VGA port (VGA1, see page 17, No. 4) of VGA_HDTV panel.

Step 2. Connect the Male/Male RCA patch cables to the Typical HDTV component

Video Input connectors and the RCA-type component video connectors

(Y-CON1, PB-CON1, and PR-CON1) (Y-CON1, see page 17, No. 1; PB-

CON1, see page 17, No. 2; PR-CON1, see page 17, No. 3) of the

VGA_HDTV panel.

Step 3. Turn on your computer and wait system to boot into OS.

Step 4. Enable the TV display. Please follow the below steps:

A. Access the Windows Control Panel. Double-click Display.

B. Click the Settings tab and then the Advanced button.

C. Click the ATI Displays tab. Click the TV button.

C. Click the Advanced button, then click the Displays tab.

D. Click the YPbPr tab.

E. Click OK.

F. Click the Advanced button.

G. Click the Adapter tab, then click the List All Modes button.

H. You can only choose 480i and 480p modes (640 x 480; 704 x 480;

720 x 480), 720p modes (960 x 720; 1280 x 720), or 1080i modes

(1920 x 1080). Click the mode according to your HDTV screen.

• 60Hz = Progressive

• 30Hz = Interlaced

In DOS mode, only 480p is supported for HDTV output.

A. Click the Windows Start button, point at Settings, and then click

Control Panel.

B. Double-click the Display icon, click the Settings tab, and use the

Screen Area slider to select the resolution you want.

If the resolution you select is not related to a specific timing, the

system will reduce the resolution to the closest supported timing.

2020

20

ASRock 775Twins-HDTV Motherboard

EnglishEnglish

English

Enable Button (Green) Disable Button (Red)

2.8.2 TV Support Function2.8.2 TV Support Function

2.8.2 TV Support Function

Connecting to TV With AV Output CapabilityConnecting to TV With AV Output Capability

Connecting to TV With AV Output Capability

Step 1. Connect the AV video cable to the Typical TV Video Input connector

(yellow) and the RCA-type component video connector (blue) / AV

(composite) signal connector (PB-CON1, see page 17, No. 2) of the

VGA_HDTV panel.

Step 2. Turn on your computer and wait system to boot into OS.

Connecting to VGA Monitor and TV With AV OutputConnecting to VGA Monitor and TV With AV Output

Connecting to VGA Monitor and TV With AV Output

CapabilityCapability

Capability

When you install both VGA monitor cable and AV video cable to VGA_HDTV panel

at the same time, the default enabled screen is the VGA monitor. You are able to

switch the monitor display to TV display by following the below instruction.

Step 1. Connect one end of the VGA monitor cable to your monitor, and the other

end to the VGA port (VGA1, see page 17, No. 4) of VGA_HDTV panel.

Step 2. Connect the AV video cable to the Typical TV Video Input connector

(yellow) and the RCA-type component video connector (blue) / AV

(composite) signal connector (PB-CON1, see page 17, No. 2) of the

VGA_HDTV panel.

Step 3. Turn on your computer and wait system to boot into OS.

Step 4. Switch the monitor display to TV display and select proper TV format. For

selecting proper TV format, please follow the below steps:

A. Click the Windows Start button, point at Settings, and then click

Control Panel.

B. Double-click the Display icon, click the Settings tab, and use the

Screen Area slider to select the resolution you want.

C. Click the Advanced button, then click the Displays tab.

D. Click the TV tab, and select NTSC, PAL.

E. Your TV will start to display.

D. Click the enable button or disable button accordingly for YPbPr

display output.

E. Click OK or Apply to save the changes or use hot key to do fast

switching between CRT and YPbPr. (Default hot key is Alt-F5.)

F. Your HDTV will start to display.

Step 5. Change HDTV display settings. (Please refer to Step 3 on page 18 for

details.)

La pagina sta caricando ...

ASROCK 775TWINS-HDTV Manuale del proprietario

ASROCK 775TWINS-HDTV Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti