ASROCK P4VM890 Manuale del proprietario

11

1

ASRock P4VM890 Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans-

lated in any language, in any form or by any means, except duplication of documen-

tation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identifica-

tion or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or omissions

that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind,

either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose. In no event shall

ASRock, its directors, officers, employees, or agents be liable for any indirect, special,

incidental, or consequential damages (including damages for loss of profits, loss of

business, loss of data, interruption of business and the like), even if ASRock has been

advised of the possibility of such damages arising from any defect or error in the guide

or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Published August 2007

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic

substance controlled in Perchlorate Best Management Practices (BMP) regulations

passed by the California Legislature. When you discard the Lithium battery in

California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

ASRock P4VM890 Motherboard

22

2

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

EnglishEnglish

English

1 PS2_USB_PWR1 Jumper 16 USB 2.0 Header (USB67, Blue)

2 ATX 12V Connector (ATX12V1) 17 Chassis Speaker Header (SPEAKER 1)

3 CPU Heatsink Retention Module 18 Serial Port Connector (COM1)

4 CPU Socket 19 AMR Slot (AMR1)

5 2 x 184-pin DDR DIMM Slots (DDR1, DDR2; Blue) 20 Clear CMOS Jumper (CLRCMOS1)

6 Infrared Module Header (IR1) 21 JR1 / JL1 Jumpers

7 Flash Memory 22 Front Panel Audio Header (AUDIO1)

8 Floppy Connector (FLOPPY1) 23 Internal Audio Connector: CD1 (Black)

9 Secondary IDE Connector (IDE2, Black) 24 Internal Audio Connector: AUX1 (White)

10 Primary IDE Connector (IDE1, Blue) 25 3 x PCI Slots (PCI1- 3)

11 North Bridge Controller 26 PCI Express x16 Slot (PCIE1)

12 South Bridge Controller 27 Chassis Fan Connector (CHA_FAN1)

13 Primary Serial ATA Connector (SATA1) 28 ATX Power Connector (ATXPWR1)

14 Secondary Serial ATA Connector (SATA2) 29 Shared USB 2.0 Header (USB4_5, Blue)

15 System Panel Header (PANEL1) 30 CPU Fan Connector (CPU_FAN1)

33

3

ASRock P4VM890 Motherboard

EnglishEnglish

English

ASRock I/O PlusASRock I/O Plus

ASRock I/O Plus

TMTM

TM

1 Parallel Port 7 USB 2.0 Ports (USB01)

2 RJ-45 Port 8 USB 2.0 Ports (USB23)

3 Line In (Light Blue) 9 VGA Port

4 Line Out (Lime) 10 PS/2 Keyboard Port (Purple)

5 Microphone (Pink) 11 PS/2 Mouse Port (Green)

6 Shared USB 2.0 Ports (USB45)

ASRock P4VM890 Motherboard

44

4

1. Introduction1. Introduction

1. Introduction

Thank you for purchasing ASRock P4VM890 motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality and

endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change

without notice. In case any modifications of this manual occur, the

updated version will be available on ASRock website without further

notice. You may find the latest VGA cards and CPU support lists on

ASRock website as well.

ASRock website

http://www.asrock.com

1.1 Package Contents1.1 Package Contents

1.1 Package Contents

ASRock P4VM890 Motherboard

(Micro ATX Form Factor: 9.6-in x 8.0-in, 24.4 cm x 20.3 cm)

ASRock P4VM890 Quick Installation Guide

ASRock P4VM890 Support CD

One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

One Serial ATA (SATA) Cable (Optional)

One Serial ATA (SATA) HDD Power Cable (Optional)

One ASRock I/O Plus

TM

Shield

One COM Port Bracket

EnglishEnglish

English

55

5

ASRock P4VM890 Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - Micro ATX Form Factor: 9.6-in x 8.0-in, 24.4 cm x 20.3 cm

CPU - Socket 478 for Intel

®

Pentium

®

4 / Celeron

®

D (Prescott,

Northwood, Willamate) processors

- FSB 800/533/400 MHz

- Supports Hyper-Threading Technology (see CAUTION 1)

- Supports Untied Overclocking Technology (see CAUTION 2)

Chipset - Northbridge: VIA

®

P4M890

- Southbridge: VIA

®

VT8237R Plus

Memory - 2 x DDR DIMM slots

- Support DDR400/333

- Max. capacity: 2GB

Hybrid Booster - CPU Frequency Stepless Control (see CAUTION 3)

- ASRock U-COP (see CAUTION 4)

- Boot Failure Guard (B.F.G.)

Expansion Slot - 3 x PCI slots

- 1 x PCI Express x16 slot

- 1 x AMR slot

Graphics - Integrated VIA

®

UniChrome Pro 3D/2D Graphics

- DirectX 7.0 VGA

- Max. shared memory 64MB

Audio - Realtek ALC653 5.1channel AC’97 audio codec

LAN - VIA

®

PHY VT6103

- Speed: 10/100 Ethernet

- Supports Wake-On-LAN

Rear Panel I/O ASRock I/O Plus

TM

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x VGA Port

- 1 x Parallel Port (ECP/EPP Support)

- 6 x Ready-to-Use USB 2.0 Ports

- 1 x RJ-45 LAN Port

- Audio Jack: Line in/Front Speaker/Microphone

Connector - 2 x Serial ATA 1.5 Gb/s connectors, support RAID (RAID 0,

RAID 1 and JBOD) and “Hot Plug” functions

- 2 x ATA133 IDE connectors (support 4 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x COM port header

- CPU/Chassis FAN connector

ASRock P4VM890 Motherboard

66

6

EnglishEnglish

English

- 20 pin ATX power connector

- 4 pin 12V power connector

- CD in header

- AUX in header

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports; 2 of them are

shared with USB45 ports on the I/O panel)

(see CAUTION 5)

BIOS Feature - 4Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- AMBIOS 2.3.1 Support

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU Fan Tachometer

- Chassis Fan Tachometer

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft

®

Windows

®

2000 / XP compliant

Certifications - FCC, CE, WHQL

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting

the setting in the BIOS, applying Untied Overclocking Technology, or using the third-

party overclocking tools. Overclocking may affect your system stability, or even

cause damage to the components and devices of your system. It should be done at

your own risk and expense. We are not responsible for possible damage caused by

overclocking.

77

7

ASRock P4VM890 Motherboard

EnglishEnglish

English

CAUTION!

1. About the setting of “Hyper Threading Technology”, please check page 26

of “User Manual” in the support CD.

2. This motherboard supports Untied Overclocking Technology. Please read

“Untied Overclocking Technology” on page 19 for details.

3. Although this motherboard offers stepless control, it is not recommended

to perform over-clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU.

4. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

5. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

XP

SP1 or SP2 / 2000 SP4.

ASRock P4VM890 Motherboard

88

8

EnglishEnglish

English

2.2.

2.

InstallationInstallation

Installation

P4VM890 is a Micro ATX form factor (9.6-in x 8.0-in, 24.4 cm x 20.3 cm) motherboard.

Before you install the motherboard, study the configuration of your chassis to en-

sure that the motherboard fits into it.

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install motherboard com-

ponents or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component.

2. To avoid damaging the motherboard components due to static electricity,

NEVER place your motherboard directly on the carpet or the like. Also

remember to use a grounded wrist strap or touch a safety grounded

object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded anti-

static pad or in the bag that comes with the component.

Before you install or remove any component, ensure that the power is

switched off or the power cord is detached from the power supply.

Failure to do so may cause severe damage to the motherboard,

peripherals, and/or components.

99

9

ASRock P4VM890 Motherboard

2.1 CPU Installation2.1 CPU Installation

2.1 CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90° angle.

Step 2. Position the CPU directly above the socket such that its marked corner

matches the base of the socket lever.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the

CPU into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push down

the socket lever to secure the CPU. The lever clicks on the side tab to

indicate that it is locked.

2.2 Installation of CPU Fan and Heatsink2.2 Installation of CPU Fan and Heatsink

2.2 Installation of CPU Fan and Heatsink

This motherboard adopts 478-pin CPU socket to support Intel

®

Pentium

®

4

/

Celeron

®

CPU. It requires larger heatsink and cooling fan to dissipate heat.

You also need to spray thermal grease between the CPU and the heatsink to

improve heat dissipation. Make sure that the CPU and the heatsink are se-

curely fastened and in good contact with each other. Then connect the CPU

fan to the CPU_FAN connector (CPU_FAN1, see p.2 No. 30). For proper

installation, please kindly refer to the instruction manuals of the CPU fan and

the heatsink.

STEP 1:

Lift The Socket Lever Up to 90°

STEP 2/STEP 3:

Match The CPU Marked Corner

to The Socket Marked Corner

STEP 4:

Push Down And Lock

The Socket Lever

Lift Lever Up to 90°

CPU Marked Corner

Socket Marked Corner

EnglishEnglish

English

ASRock P4VM890 Motherboard

1010

10

EnglishEnglish

English

2.3 Installation of Memory Modules (DIMM)2.3 Installation of Memory Modules (DIMM)

2.3 Installation of Memory Modules (DIMM)

P4VM890 motherboard provides two 184-pin DDR (Double Data Rate) DIMM slots.

Please make sure to disconnect power supply before adding or removing

DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause

permanent damage to the motherboard and the DIMM if you

force the DIMM into the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

1111

11

ASRock P4VM890 Motherboard

EnglishEnglish

English

2.4 Expansion Slots (PCI, AMR and PCI Express Slots)2.4 Expansion Slots (PCI, AMR and PCI Express Slots)

2.4 Expansion Slots (PCI, AMR and PCI Express Slots)

There are 3 PCI slots, 1 AMR slot, and 1 PCI Express slot on this motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

AMR slot: The AMR slot is used to insert an ASRock MR card with v.92 Modem

functionality.

PCIE Slots: PCIE1 (PCIE x16 slot) is used for PCI Express cards with x16 lane

width graphics cards.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in a

chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

ASRock P4VM890 Motherboard

1212

12

EnglishEnglish

English

2.5 Jumpers Setup2.5 Jumpers Setup

2.5 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper Setting

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2, No. 1) +5VSB (standby) for PS/2

or USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided

by power supply.

JR1(see p.2, No. 21)

JL1(see p.2, No. 21)

Note: If the jumpers JL1 and JR1 are short, both the front panel and the rear panel

audio connectors can work.

Clear CMOS

(CLRCMOS1, 2-pin jumper)

(see p.2, No. 24)

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short 2 pins on

CLRCMOS1 for 5 seconds.

Short

Open

2-pin jumper

1313

13

ASRock P4VM890 Motherboard

EnglishEnglish

English

2.6 Onboard Headers and Connectors2.6 Onboard Headers and Connectors

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper

caps over these headers and connectors. Placing jumper caps over the

headers and connectors will cause permanent damage of the motherboard!

FDD Connector

(33-pin FLOPPY1)

(see p.2, No. 8)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE Connector (Blue) Secondary IDE Connector (Black)

(39-pin IDE1, see p.2, No. 10) (39-pin IDE2, see p.2, No. 9)

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor

for the details. Besides, to optimize compatibility and performance, please

connect your hard disk drive to the primary IDE connector (IDE1, blue) and

CD-ROM to the secondary IDE connector (IDE2, black).

Serial ATA Connectors These two Serial ATA (SATA)

(SATA1: see p.2, No. 13) connectors support SATA data

(SATA2: see p.2, No. 14) cables for internal storage

devices. The current SATA

interface allows up to 1.5 Gb/s

data transfer rate.

Serial ATA (SATA) Either end of the SATA data

Data Cable cable can be connected to the

(Optional) SATA hard disk or the SATA

connector on the motherboard.

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

the red-striped side to Pin1

SATA1SATA2

ASRock P4VM890 Motherboard

1414

14

EnglishEnglish

English

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on the drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

USB 2.0 Header Besides six default USB 2.0

(9-pin USB67) ports on the I/O panel, there are

(see p.2, No. 16) two USB 2.0 headers on this

motherboard. Each USB 2.0

header cansupport two USB

2.0 ports. The shared USB 2.0

header (USB4_5) is shared with

Shared USB 2.0 Header USB ports 45 on the I/O panel.

(9-pin USB4_5) When using the front panel USB

(see p.2, No. 29) ports by attaching the front panel

USB cable to USB4_5 header,

the USB ports 45 on the I/O panel

will not be able to function.

Infrared Module Header This header supports an optional

(5-pin IR1) wireless transmitting and

(see p.2, No. 6) receiving infrared module.

Internal Audio Connectors These connectors allow you

(4-pin CD1, 4-pin AUX1) to receive stereo audio input

(CD1: see p.2, No. 23) from sound sources such as

(AUX1: see p.2, No. 24) a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

Front Panel Audio Header This is an interface for the front

(8-pin AUDIO1) panel audio cable that allows

(see p.2, No. 22) convenient connection and

control of audio devices.

connect to the

power supply

connect to the SATA

HDD power connector

CD1 AUX1

1515

15

ASRock P4VM890 Motherboard

EnglishEnglish

English

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel

(see p.2, No. 15) functions.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1) speaker to this header.

(see p.2, No. 17)

Chassis Fan Connector Please connect the chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2, No. 27) match the black wire to the

ground pin.

CPU Fan Connector Please connect the CPU fan

(3-pin CPU_FAN1) cable to this connector and

(see p.2, No. 30) match the black wire to the

ground pin.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2, No. 28)

ATX 12V Connector Please note that it is necessary

(4-pin ATX12V1) to connect a power supply with

(see p.2, No. 2) ATX 12V plug to this connector

so that it can provides sufficient

power. Failing to do so will cause

the failure to power up.

Serial port connector This COM1 connector

(9-pin COM1) supports a serial port module.

(see p.2, No. 18)

Please install the heatsink and the CPU fan before installing ATX 12V

connector; otherwise, it may cause permanent damage!

ASRock P4VM890 Motherboard

1616

16

EnglishEnglish

English

2.7 Serial A2.7 Serial A

2.7 Serial A

TT

T

A (SAA (SA

A (SA

TT

T

A) Hard Disks InstallationA) Hard Disks Installation

A) Hard Disks Installation

This motherboard adopts VIA

®

VT8237R Plus southbridge chipset that supports

Serial ATA (SATA) hard disks and RAID (RAID 0, RAID 1 and JBOD) functions. You

may install SATA hard disks on this motherboard for internal storage devices. This

section will guide you to install the SATA hard disks.

STEP 1: Install the SATA hard disks into the drive bays of your chassis.

STEP 2: Connect the SATA power cable to the SATA hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s SATA

connector.

STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.

2.8 Hot Plug and Hot Swap F2.8 Hot Plug and Hot Swap F

2.8 Hot Plug and Hot Swap F

unctions for SAunctions for SA

unctions for SA

TT

T

A HDDsA HDDs

A HDDs

P4VM890 motherboard supports Hot Plug and Hot Swap functions for

SATA Devices.

NOTE

What is Hot Plug Function?

If the SATA HDDs are NOT set for RAID configuration, it is called “Hot

Plug” for the action to insert and remove the SATA HDDs while the system

is still power-on and in working condition.

However, please note that it cannot perform Hot Plug if the OS has been

installed into the SATA HDD.

What is Hot Swap Function?

If SATA HDDs are built as RAID1 then it is called “Hot Swap” for the action

to insert and remove the SATA HDDs while the system is still power-on

and in working condition.

2.92.9

2.9

Driver Installation GuideDriver Installation Guide

Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical

drive first. Then, the drivers compatible to your system can be auto-detected and

listed on the support CD driver page. Please follow the order from up to bottom

side to install those required drivers. Therefore, the drivers you install can work

properly.

1717

17

ASRock P4VM890 Motherboard

EnglishEnglish

English

2.112.11

2.11

Installing WindowsInstalling Windows

Installing Windows

®

2000 / XP With RAID Functions 2000 / XP With RAID Functions

2000 / XP With RAID Functions

If you want to install Windows

®

2000 / Windows

®

XP OS on your SATA

HDDs with RAID functions, please follow below steps.

STEP 1: Set up BIOS.

A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration.

B. Set the “SATA Operation Mode” option to [RAID].

STEP 2: Make a SATA driver diskette.

A. Insert the ASRock Support CD into your optical drive to boot your system.

B. During POST at the beginning of system boot-up, press <F11> key, and

then a window for boot devices selection appears. Please select CD-

ROM as the boot device.

C. When you see the message on the screen, “Generate Serial ATA driver

diskette [YN]?”, press <Y>.

D. Then you will see these messages,

Please insert a blank

formatted diskette into floppy

drive A:

press any key to start

Please insert a floppy diskette into the floppy drive, and press any key.

E. The system will start to format the floppy diskette and copy SATA drivers

into the floppy diskette.

STEP 3: Use “RAID Installation Guide” to set RAID configuration.

Before you start to configure RAID function, you need to check the RAID installation

guide in the Support CD for proper configuration. Please refer to the document in the

following path in the Support CD:

.. \ RAID Installation Guide

STEP 4: Install Windows

®

2000 / XP OS on your system.

After step1, 2, 3, you can start to install Windows

®

2000 / Windows

®

XP OS on your

system. At the beginning of Windows

®

setup, press F6 to install a third-party RAID

driver. When prompted, insert the SATA driver diskette containing the VIA

®

RAID

driver. After reading the floppy disk, the driver will be presented. Select the driver to

install according to the mode you choose and the OS you install.

2.102.10

2.10

AMR Card and Driver Installation AMR Card and Driver Installation

AMR Card and Driver Installation

If you do not insert AMR card to this motherboard, and you finish installing all

drivers to your system now, but in the future, you plan to use AMR card function

on this motherboard, please follow the steps below then.

1. Insert AMR card to AMR slot on this motherboard. Please make sure that the

AMR card is completely seated on the slot.

2. Install AMR card driver from our support CD to your system.

3. Reboot your system.

ASRock P4VM890 Motherboard

1818

18

If you want to use “VIA RAID Tool” in Windows

®

environment, please install

SATA drivers from the Support CD again so that “VIA RAID Tool” will be

installed to your system as well.

NOTE. If you install Windows

®

2000 / Windows

®

XP on IDE HDDs and want to manage

(create, convert, delete, or rebuild) RAID functions on SATA HDDs, you still need to

set up “SATA Operation Mode” to [RAID] in BIOS first. Then, please set the RAID

configuration by using the document in the following path in the Support CD:

.. \ RAID Installation Guide

2.12 Installing Windows2.12 Installing Windows

2.12 Installing Windows

®

2000 / XP Without RAID 2000 / XP Without RAID

2000 / XP Without RAID

FunctionsFunctions

Functions

If you want to install Windows

®

2000 / XP on your SATA HDDs without RAID functions,

please follow below steps.

STEP 1: Set up BIOS.

A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration.

B. Set the “SATA Operation Mode” option to [non-RAID].

STEP 2: Install Windows

®

2000 / XP OS on your system.

After setting up BIOS, you can start to install Windows

®

2000 / XP on your

system.

EnglishEnglish

English

1919

19

ASRock P4VM890 Motherboard

3. BIOS Information3. BIOS Information

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up

the computer, please press <F2> during the Power-On-Self-Test (POST) to enter

BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to

enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> +

<Delete>, or pressing the reset button on the system chassis.

The BIOS Setup program is designed to be user-friendly. It is a menu-driven program,

which allows you to scroll through its various sub-menus and to select among the

predetermined choices. For the detailed information about BIOS Setup, please refer

to the User Manual (PDF file) contained in the Support CD.

4. Software Suppor4. Software Suppor

4. Software Suppor

t CD informationt CD information

t CD information

This motherboard supports various Microsoft

®

Windows

®

operating systems: 2000 /

XP. The Support CD that came with the motherboard contains necessary drivers and

useful utilities that will enhance motherboard features.

To begin using the Support CD, insert the CD into your CD-ROM drive. It will display

the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main

Menu does not appear automatically, locate and double-click on the file

“ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.

EnglishEnglish

English

2.132.13

2.13

Untied Overclocking TUntied Overclocking T

Untied Overclocking T

echnologyechnology

echnology

This motherboard supports Untied Overclocking Technology, which means during

overclocking, FSB enjoys better margin due to fixed PCI / PCIE bus. You may set “CPU

Host Frequency” option of BIOS setup to [Auto], which will show you the actual CPU

host frequency in the following item. Therefore, CPU FSB is untied during overclocking,

but PCI / PCIE bus is in the fixed mode so that FSB can operate under a more stable

overclocking environment.

Please refer to the warning on page 6 for the possible overclocking risk before

you apply Untied Overclocking Technology.

ASRock P4VM890 Motherboard

2020

20

DeutschDeutsch

Deutsch

1. Einführung1. Einführung

1. Einführung

Wir danken Ihnen für den Kauf des ASRock P4VM890 Motherboard, ein zuverlässiges

Produkt, welches unter den ständigen, strengen Qualitätskontrollen von ASRock

gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes Design, gemäß der

Verpflichtung von ASRock zu Qualität und Halbarkeit.

Diese Schnellinstallationsanleitung führt in das Motherboard und die schrittweise

Installation ein. Details über das Motherboard finden Sie in der Bedienungsanleitung

auf der Support-CD.

Da sich Motherboard-Spezifikationen und BIOS-Software verändern können,

kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert werden. Für

den Fall, dass sich Änderungen an diesem Handbuch ergeben, wird eine neue

Version auf der ASRock-Website, ohne weitere Ankündigung, verfügbar sein.

Die neuesten Grafikkarten und unterstützten CPUs sind auch auf der

ASRock-Website aufgelistet.

ASRock-Website: http://www.asrock.com

1.1 Kartoninhalt

ASRock P4VM890 Motherboard

(Micro ATX-Formfaktor: 24.4 cm x 20.3 cm; 9.6 Zoll x 8.0 Zoll)

ASRock P4VM890 Schnellinstallationsanleitung

ASRock P4VM890 Support-CD

Ein 80-adriges Ultra-ATA 66/100/133 IDE-Flachbandkabel

Ein Flachbandkabel für ein 3,5-Zoll-Diskettenlaufwerk

Ein Seriell-ATA- (SATA) Datenkabel (Option)

Ein Seriell-ATA (SATA) Festplattennetzkabel (Option)

Ein ASRock I/O Plus

TM

Shield

Ein COM Port-Anschlusshalter (Option)

La pagina sta caricando ...

ASROCK P4VM890 Manuale del proprietario

ASROCK P4VM890 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti