Dell PowerEdge C6220 II Guida utente

Dell PowerEdge

C6220 II

Getting Started

With Your System

Mise en route du système

Introdução ao uso do sistema

Pasos iniciales para su sistema

Dell PowerEdge

C6220 II

Getting Started

With Your System

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of

data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

______________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission

of Dell Inc. is st rict ly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of

Dell Inc. Intel® and Intel® Xeon® are registered trademarks of Intel Corporation in the

U.S. and other count ries. Red Hat Enterprise Linux® and Enterprise Linux® are

registered trademarks of Red Hat, Inc. in the United States and/or other countries.

Novell® is a registered trademark and SUSE™ is a trademark of Novell Inc. in the United

States and other countries. Citrix® and XenServer® are either registered trademarks or

trademarks of Citrix Systems, Inc. in the United States and/or other countries. VMware®

is a registered trademarks or trademarks of VMWare, Inc. in the United States or other

countries.

Other trademarks and trade names may be used in this publication to refer to either the

entities claiming the marks and names or their products. Dell Inc. disclaims any

proprietary interest in trademarks and trade names other than its own.

Regulatory Model B08S

May 2013 P/N 1PFTR Rev. A00

Getting Started With Your System | 3

CAUTION: Restricted Access Location

This server is intended for installation only in restricted access locations as

defined in Cl. 1.2.7.3 of I EC 60950-1: 2001 where both these conditions apply:

• Access can only be gained by service persons or by users who have been

instructed about the reasons for the restrictions applied to the location and

about any precautions that shall be taken.

• Access is through the use of a tool or lock and key, or ot her means of

security, and is controlled by the authority responsible for the location.

Installation and Configuration

WARNING: Before performing the following procedure, review and follow the

safety instructions that came with the system.

Installing the Tool-Less Rail Solution

WARNING: Whenever you

need to lift the system, get others to assist you.

To avoid injury, do not attempt to lift the system by yourself.

WARNING: The system is not fixed to the rack or mounted on the rails. To

avoid personal injury or damage to the system, you must adequately

support the system during installation and removal.

WARNING: To avoid a potential electrical shock hazard, a third wire safety

grounding conductor is necessary for the rack installation. The rack

equipment must provide sufficient airflow to the system to maintain proper

cooling.

CAUTION: When installing rails in a square-hole rack it is important to

ensure that the square peg slides through the square holes.

Getting Started With Your System | 4

1 Push on the latch release buttons on the midpoints of the end piece t o

open the rail latches. See Figure 1.

2 Align the end pieces of the rails on the vertical rack flanges to seat

the pegs in the bottom hole of the first U and the top hole of the

second U.

NOTE: The rails can be used in both square-hole (item 1 in the following figure)

and round-hole racks (item 2 in the following figure).

Figure 1. Pushing the Latch Release Buttons

NOTE: To remove the rails, push on the latch release button on the midpoints

of the end piece and unseat each rail.

Getting Started With Your System | 5

3 Engage the end of the rails and release the latch release button to

have the latches locked in place. See Figure 2.

Figure 2. Releasing the Latch Release Buttons

Getting Started With Your System | 6

4 On each vertical rack flange on the back, put two screw bases into

the two square holes right above the rail. See Figure 3.

5 Install the chassis stabilizer shipping brackets (optional) on the back

rack flanges.

6 Install and tight en the s crews.

NOTE: To transport systems already installed in the rack, ensure that the two

chassis stabilizer shipping brackets (optional) are in place.

Figure 3. Installing the Chassis Stabilizer Shipping Brackets

Getting Started With Your System | 7

7 Slide the system into the rack. See Figure 4.

8 Tighten the thumbscrews to secure the ears of the system to the front

of t he rack flanges.

Figure 4. Installing the Chassis onto the Rack.

Getting Started With Your System | 8

Optional—Connecting the Keyboard, Mouse, and Monitor

Figure 5. Optional—Connecting the Keyboard, Mouse and Monitor

Connect the keyboard, mouse, and monitor (optional).

The connectors on the back of your system have icons indicating which cable to

plug into each connect or. Be sure to tight en the screws (if any) on t he monitor’s

cable connector.

Getting Started With Your System | 9

Connecting the Power Cable(s)

Figure 6. Connecting the Power Cable

Connect the system’s power cable(s) to the system and, if a monitor is used,

connect t he monitor’s p ower cable to t he monitor. Plug the other end of t he

power cables into a grounded electrical outlet or a separate power source such as

an unint errupted power supply or a p ower distribution unit.

NOTE: Your system can support up to two 1200 W power supply units (100-240 VAC

nominal input voltage) or up to two 1400 W power supply units (200-240 VAC nominal

input voltage).

Getting Started With Your System | 10

Turning on the System

Figure 7. Pressi ng the Power Button on the Front of the System

Figure 8. Pressi ng the Power Button on the Back of the System

Press the power button(s) either on the front or b ack of the system. The power

indicators should light green.

Getting Started With Your System | 11

Complete the Operating System Setup

To install an operating system for the first time, see the installation and

configuration documentat ion for your operating system. Be sure the op erating

system is installed before installing hardware or software not purchased with the

system.

NOTE: See dell.com/ossupport for the latest information on supported

operating systems.

Other Information You May Need

WARNING: See the safety and regulatory information that shipped with your

system. Warranty information may be included within this document or as a

separate document.

The Hardware Owner’s Manual provides information about system features and

describes how to troubleshoot the system and install or replace system

components. This document is available at dell.com/support/manuals.

Dell systems management application documentation provides information

about installing and using the systems management software. This document is

available online at dell.com/support/manuals.

NOTE: Always check for updates on dell.com/support/manua ls and read the

updates first because they often supersede information in other documents.

NOM Information (Mexico Only)

The following information is provided on the device described in this document

in compliance with the requirements of the official M exican st andards (NOM ):

Importer Dell Inc. de M éxico, S.A. de C.V.

Paseo de la Reforma 2620-11° Piso

Col. Lomas Atlas

11950 M éxico, D.F.

Model number B08S

Getting Started With Your System | 12

Supply voltage 100-240 V AC with 1200 W Power

Supply Unit

200-240 V AC with 1400 W Power

Supply Unit

Frequency 50/60 Hz

Current consumption 12-8 A mps w ith 1200 W Power Supply

Unit

9 Amps with 1400 W Power Supply

Unit

Technical Specifications

Power

NOTE: The system doesn’t support a mixed installation of 1200 W and 1400 W power supply

units.

NOTE: Both the 1200 W and 1400 W PSUs are hot swappable, and they can support hot swap in

any condition if the system has the power throttling feature.

AC power supply (per power supply)

Wattage

1200 W

Voltage 100-240 VAC, 50/60 Hz, maximum input

current: 12.0-8.0 Amps

NOTE: For 1200 W power supply, output 1200 W is for

high line (input 200-240 VAC), output 1023 W is for low

line (input 100-120 VAC).

Heat dissipation

4016.251 BTU/hr maximum

Maximum inrush current Initial In-rush Current cannot exceed 55

Amps (p eak). Secondary In-rush Current

cannot exceed 35 Amps (peak).

Wattage

1400 W

Voltage 200-240 VAC, 50-60 Hz, maximum input

current: 9.0 Amps

Heat dissipation

6024.376 BTU/hr maximum.

Maximum in-rush current Initial In-rush Current cannot exceed 55

Amps (p eak). Secondary In-rush Current

cannot exceed 25 Amps (peak).

Getting Started With Your System | 13

Battery (per system board)

System battery

CR 2032 3.0-V lithium ion coin cell

Physical

Height

8.68 cm (3.42 in)

Width

44.8 cm (17.6 in)

Depth

79.0 cm (31.1 in)

Weight (maximum

configuration)

41 kg (90.38 lb) (with 12*3.5” HDD)

39 kg (86.00 lb) (with 24*2.5” HDD)

Weight (empty) 15.7 kg (34.61 lb) (with 2.5” HDD bay)

15.1 kg (33.29 lb) (with 3.5” HDD bay)

Environmental

NOTE: For additional information about environmental measurements for specific system

configurations, see www.dell.com/environmental_datasheets.

Te mperature

Operat ing 10° to 35°C (50° to 95°F) with a maximum

temperature gradation of 10°C p er hour

NOTE: For altitudes above 2950 feet, the maximum

operating temperature is derated 1°F/550 ft.

CAUTION: The maximum number of memory modules

and hard drives supported on 1U and 2U node

configurations, with 130W (4 and 8 core) and 135W

processors, depends on the power supply installed.

St orage –40° t o 65°C (–40° to 149°F) wit h a

maximum temperature gradation of 20°C p er

hour

Relative humidity

Operat ing 20% to 80% (noncondensing) with a maximum

humidity gradation of 10% per hour

St orage

5% to 95% (noncondensing)

Maximum vibration

Operat ing

0.26 Grms at 5–350 Hz

St orage 1.88 Grms at 10–500 Hz for 15 min

Getting Started With Your System | 14

Maximum shock

Operat ing One shock pulse in the positive z axis

(one pulse on each side of the system) of 31 G

for 2.6 ms in the operational orient ation

St orage Six consecutively executed shock pulses in the

positive and negative x, y, and z axes

(one pulse on each side of the system) of 71 G

for up to 2 ms;

Six consecutively executed shock pulses in the

positive and negative x, y, and z axes

(one pulse on each side of the system) of 27 G

faired square wave pulse with velocity change

at 235 inches/second (597 centimeters/second)

Altitude

Operat ing

-15.2 to 3,048 m (-50 t o 10,000 ft.)

St orage

-15.2 to 10,668 m (-50 to 35,000 ft.)

Airborne Contaminant Level

Clas s

G1 as defined by ISA-S71.04-1985

Dell PowerEdge

C6220 II

Mise en route

du système

Remarques, précautions et

avertissements

REMARQUE : une REMARQUE indique des informations importantes qui vous

aident à mieux utiliser votre ordinateur.

PRÉCAUTION : une PRÉCAUTION indique un risque d'endommagement du

matériel ou de perte de données si les instructions ne sont pas respectées.

AVERTISSEMENT : un AVERTISSEMENT indique un risque

d'endommagement du matériel, de blessure corporelle ou de mort.

______________

Les informations que contient ce document sont sujettes à modification sans préavis.

La reproduct ion de ce document, sous quelque forme que ce soit , sans le consentement

écrit de Dell Inc. est strictement interdite.

Marques ut ilisées dans ce document : Dell™, le logo Dell et PowerEdge™ sont des

marques de Dell Inc. Intel® et Int el® Xeon® sont des marques déposées d'Intel

Corporat ion aux Ét ats-Unis et dans d'autres pay s. Red Hat Enterp rise Lin ux® et Ent erprise

Linux® sont des marques déposées de Red Hat, Inc. aux États-Unis et /ou dans d'aut res

pays. Novell® est une marque déposée et SUSE™ est une marque de Novell Inc. aux

États-Unis et dans d'autres pays. Citrix® et XenServer® sont des marques déposées ou

des marques de Citrix Syst ems, In c. aux Ét at s-Unis et/ou dans d'autres pays. VMware®

est une marque déposée ou une marque de VMWare, Inc. aux États-Unis ou dans

d'autres pays.

D'autres marques et noms commerciaux peuvent être ut ilisés dans ce document pour faire

référence aux entités se réclamant de ces marques ou noms ou à leurs produits. Dell Inc.

rejette tout intérêt propriétaire dans les marques et les noms commerciaux autres que

les siens.

Modèle réglementaire B08S

Mai 2013 N/P 1PFTR Rév. A00

Mise en route du système | 17

PRÉCAUTION : emplacement à accès restreint

Ce serveur est conçu pour être installé uniquement à des emplacement à accès

restreint tels que définis dans la norme Cl. 1.2.7.3 of IEC 60950-1: 2001 où les

deux conditions suivantes s'appliquent :

• Seuls peuvent accéder à ce serveur les utilisateurs ou le personnel

d'ent ret ien qui ont reçu des instructions quant aux raisons pour lesquelles

les restrictions concernant l'emplacement s'appliquent et pour lesquelles

toutes les précautions doivent être prises.

• L'accès se fait grâce à un outil ou un verrou et une clé ou d'autres moyens

de sécurité et est contrôlé par l'autorité en charge de l'emplacement.

Installation et configuration

AVERTISSEMENT : avant d'effectuer la procédure suivante, consultez et

respectez les consignes de sécurité qui accompagnent le système.

Installation sans outils de la solution rails

AVERTISSEMENT : demandez toujours de l'aide pour soulever le système.

Pour éviter de vous blesser, ne tentez pas de soulever le système

tout seul.

AVERTISSEMENT : le système n'est pas fixé au rack ni monté sur les rails.

Pour éviter de vous blesser ou d'endommager le système, assurez-vous

qu'il dispose de support au cours de son installation et de son retrait.

AVERTISSEMENT : pour réduire les risques de blessures corporelles

provoquées par d'éventuels chocs électriques, ajoutez un troisième

conducteur de mise à la masse de sécurité lors de l'installation du rack.

La ventilation fournie par l'équipement de rack doit être suffisante pour

assurer le refroidissement du système.

PRÉCAUTION : lors de l'installation de rails dans un rack à trous carrés,

il

importe de s'assurer que les ergots s'emboîtent dans les trous carrés

.

Mise en route du système | 18

1 Poussez sur les boutons de dégagement du loquet au milieu de la

pièce d'ext rémit é p our ouvrir les loquets du rail. Voir Figure 1.

2 Alignez les pièces d'extrémité des r ails sur les collerettes vert icales

du rack pour inst aller les ergots dans le trou du bas du premier U

et le trou du haut du deuxième U.

REMARQUE : les rails peuvent s'utiliser tant dans les racks à trous carrés

(élément 1 dans la figure suivante) que dans les racks à trous ronds (élément 2

dans la figure suivante).

Figure 1. Appui sur les boutons d'ouverture des loquets

REMARQUE : pour retirer les rails, poussez sur le bouton d'ouverture du

loquet au milieu de la pièce d'extrémité et dégagez chaque rail.

La pagina sta caricando ...

Dell PowerEdge C6220 II Guida utente

Dell PowerEdge C6220 II Guida utente

in altre lingue

Documenti correlati

Altri documenti