Brother P-touch 1400 Guida utente

Printed in China

LN9969001

USER’S GUIDE

GUÍA DE USUARIO

1400

• Read this User’s Guide before you start using your P-touch.

• Keep this User’s Guide in a handy place for future reference.

• Antes de usar su equipo por primera vez, lea cuidadosamente esta guía de usuario.

• Guarde esta guía de usuario para futuras referencias.

USER’S GUIDE

GUÍA DE USUARIO

PT1400_cover1_4

Introduction

Thank you for purchasing this P-touch!

With your new P-touch, select from a variety of character styles, sizes and frames to

design practical custom labels for any need. In addition, the selection of pre-formatted

label types allows you to quickly and easily label patch panels, cables, connectors and

other components.

With this P-touch, you can print legible, long-lasting labels in no time. The quality and

performance of this P-touch make it an extremely practical machine in the plant or in the

field.

Although this P-touch is easy to use, we suggest that you read this User’s Guide

carefully before starting, and then keep this manual nearby for future reference.

Federal Communications Commission (FCC) Declaration of Conformity (For USA Only)

Responsible Party : Brother International Corporation

100 Somerset Corporate Boulevard

Bridgewater, NJ 08807-0911 USA

TEL : (908) 704-1700

declares that the product

Product Name : Brother Label Printer P-touch

Model Number : PT-1400

complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received,including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-

ence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause harmful interference to radio commu-

nications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turn-

ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol-

lowing measures:

- Reorient or relocate the receiving antenna

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

- The enclosed interface cable should be used in order to ensure compliance with the limits for a Class B digital

device.

- Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user’s authority

to operate the equipment.

PT1400_cover2_3

i

CONTENTS

Brother

®

90 Days/One Year Limited Warranty and Replacement

Service (For USA Only) ................................................................iii

Important Information ................................................................... v

1. Getting Started ..............................................................1

General Description ......................................................................1

Top view & bottom view ...............................................................................1

Keyboard & LCD display .............................................................................2

General Precautions ......................................................................3

Batteries & Tape Cassettes .............................................................4

Installing batteries and a tape cassette .........................................................4

Cleaning ........................................................................................7

Cleaning the print head, rollers and tape cutter ..........................................7

Optional AC Adapter ..................................................................... 8

Connecting the AC adapter ...........................................................................8

Turning the P-touch On/Off ..........................................................8

2. Label Type Modes ..........................................................9

Selecting a Label Type Mode .........................................................9

Normal and Vertical Modes ...........................................................9

Rotate Mode and Rotate & Repeat Mode .....................................10

Flag Mode ....................................................................................11

Port & Panel Modes .....................................................................12

3. Basic Functions ............................................................14

Performing Basic Operations .......................................................14

Choosing functions, parameters, settings and groups ................................14

Choosing the default setting .......................................................................14

Confirming a choice ....................................................................................14

Cancelling a choice ....................................................................................14

Inputting Label Data ....................................................................15

Entering and editing text .............................................................................15

Entering an accented character ..................................................................17

Entering a bar code ....................................................................................18

Entering a symbol .......................................................................................20

ii

Formatting the Label ....................................................................23

Specifying a label length .............................................................................23

Specifying a margin size .............................................................................23

Framing the text ..........................................................................................24

Specifying the character size ......................................................................25

Specifying the character width ...................................................................26

Specifying the character style .....................................................................27

Using the pre-formatted Auto Format templates ........................................29

Printing Labels .............................................................................30

Previewing the label layout ........................................................................30

Feeding tape ...............................................................................................30

Printing a label ...........................................................................................30

Using special printing functions .................................................................31

Storing and Recalling Files ...........................................................35

Storing label text .........................................................................................35

Recalling text that has been stored .............................................................36

Deleting text that has been stored ...............................................................36

4. Machine Adjustments ..................................................37

Selecting how tape is fed and cut ................................................................37

Adjusting the display contrast .....................................................................37

Setting the Auto Reduction function ............................................................38

Calibrating the label length ........................................................................38

Specifying if the PERSONAL symbol category is continually updated ......39

Changing the units of measure ...................................................................39

Changing the language ...............................................................................39

Displaying version information ..................................................................39

5. Appendix .....................................................................40

Troubleshooting ...........................................................................40

Error Message List ........................................................................41

Machine Specifications ................................................................45

Hardware ....................................................................................................45

Software ......................................................................................................45

Index ...........................................................................................46

Contact Information (For USA Only) ...........................................49

iii

Brother

®

90 Days/One Year Limited Warranty and Replacement Service

(For USA Only)

Who is covered:

• This limited warranty (“warranty”) is given only to

the original end-use/retail purchaser (referred to in

this warranty as “Original Purchaser”) of the

accompanying product, consumables and

accessories (collectively referred to in this

warranty as “this Product”).

• If you purchased a product from someone other

than an authorized Brother reseller in the United

States or if the product was used (including but not

limited to floor models or refurbished product),

prior to your purchase you are not the Original

Purchaser and the product that you purchased is

not covered by this warranty.

What is covered:

• This Product includes a Machine and Consumable

and Accessory Items. Consumable and Accessory

Items include but are not limited to label cassettes,

cutters, stamps, power adapters, cases and

batteries.

• Except as otherwise provided herein, Brother

warrants that the Machine and the accompanying

Consumable and Accessory Items will be free

from defects in materials and workmanship, when

used under normal conditions.

• This warranty applies only to products purchased

and used in the United States. For products

purchased in, but used outside, the United States,

this warranty covers only warranty service within

the United States (and does not include shipping

outside the United States).

What is the length of the Warranty Period(s):

• Machines have a two-stage warranty: 90 days from

the original purchase date and an additional

warranty up to one year from the original purchase

date.

• Consumable and Accessories Items accompanying

the Machine have a one-stage warranty: 90 Days

from the original purchase date.

What is NOT covered:

This warranty does not cover:

(1) Physical damage to this Product;

(2) Damage caused by improper installation, improper

or abnormal use, misuse, neglect or accident

(including but not limited to transporting this

Product without the proper preparation and/or

packaging);

(3) Damage caused by another device or software

used with this Product (including but not limited to

damage resulting from use of non Brother

®

-brand

parts and Consumable and Accessory Items);

(4) Consumable and Accessory Items that expired in

accordance with a rated life; and,

(5) Problems arising from other than defects in

materials or workmanship.

This limited warranty is VOID if this Product has been

altered or modified in any way (including but not

limited to attempted warranty repair without

authorization from Brother and/or alteration/removal

of the serial number).

What to do if you think your Product is eligible for

warranty service:

Report your issue to either our Customer Service

Hotline at 1-877-478-6824

or a Brother Authorized

Service Center within the applicable warranty

period. Supply Brother or the Brother Authorized

Service Center with a copy of your dated bill of sale

showing that this Product was purchased within the

U.S. For the name of local Brother Authorized Service

Center(s), call 1-800-521-2846.

What Brother will ask you to do:

After contacting Brother or a Brother Authorized

Service Center, you may be required to deliver (by

hand if you prefer) or send the Product properly

packaged, freight prepaid, to the Authorized Service

Center together with a photocopy of your bill of sale.

You are responsible for the cost of shipping,

packing product, and insurance (if you desire). You

are also responsible for loss or damage to this

Product in shipping.

What Brother will do:

First 90 Days

: If the problem reported concerning your

Machine and/or accompanying Consumable and

Accessory Item(s) is covered by this warranty and

if

you first reported the problem to Brother or an

Authorized Service Center within 90 days from the

date of original purchase, Brother or its Authorized

Service Center will repair or replace the Machine and/

or accompanying Consumable and Accessory Item(s)

at no charge to you for parts or labor. The decision as

to whether to repair or replace the Machine and/or

accompanying Consumable and Accessory Item(s) is

made by Brother in its sole discretion. Brother reserves

the right to supply a refurbished or remanufactured

replacement Machine and/or accompanying

Consumable and Accessory Item(s) and use

refurbished parts provided such replacement products

conform to the manufacturer’s specifications for new

product/parts. The repaired or replacement Machine

and/or accompanying Consumable and Accessory

Item(s) will be returned to you freight prepaid or made

available for you to pick up at a conveniently located

Authorized Service Center.

iv

Brother

®

90 Days/One Year Limited Warranty and Replacement Service

(For USA Only)

91

st

day to 1 year:

If the problem reported concerning your Machine is

covered by this warranty and

if you first reported the

problem after 90 days, but before 1 year from the date

of original purchase, Brother will furnish, free of

charge (excluding labor charges), replacement part(s)

for those part(s) of the Machine determined by Brother

or its Authorized Service Center to be defective. You

will be responsible for all labor charges associated

with repairs made after the first 90 days from

original purchase. After 90 days from the original

purchase date, accompanying Consumable and

Accessory Items are no longer covered by this

warranty. If the Machine and/or accompanying

Consumable and Accessory Item(s) are not covered by

this warranty (either stage), you will be charged for

shipping the Machine and/or accompanying

Consumable and Accessory Item(s) back to you.

The foregoing are your sole (i.e., only) and exclusive

remedies under this warranty.

What happens when Brother elects to replace your

Machine:

If you have delivered the Machine to an Authorized

Service Center, the Authorized Service Center will

provide you with a replacement Machine after

receiving one from Brother. If you are dealing directly

with Brother, Brother will send to you a replacement

Machine with the understanding that you will, after

receipt of the replacement Machine, supply the

required proof of purchase information, together with

the Machine that Brother agreed to replace. You are

then expected to pack the Machine that Brother agreed

to replace in the package from the replacement

Machine and return it to Brother using the air bill

supplied by Brother in accordance with the instructions

provided by Brother. Since you will be in possession of

two machines, Brother will require that you provide a

valid major credit card number. Brother will issue a

hold against the credit card account number that you

provide until Brother receives your original Product

and determines that your original Product is entitled to

warranty coverage. Your credit card will be charged up

to the cost of a new Product only if:

(i) you do not return your original Product to Brother

within five (5) business days; (ii) the problems of your

original Product are not covered by the limited

warranty; (iii) the proper packaging instructions are

not followed and has caused damage to the product; or

(iv) the warranty period on your original Product has

expired or has not been sufficiently validated with a

copy of the proof of purchase (bill of sale). The

replacement Machine you receive (even if refurbished

or remanufactured) will be covered by the balance of

the limited warranty period remaining on the original

Product, plus an additional thirty (30) days. You will

keep the replacement Machine that is sent to you and

your original Machine shall become the property of

Brother. Retain your original accessory items and a

copy of the return air bill, signed by the courier.

Limitations:

Brother is not responsible for damage to or loss of any

equipment, media, programs or data related to the use

of this Product. Except for that repair or replacement as

described above, Brother shall not be liable for any

direct, indirect, incidental or consequential damages or

specific relief. Because some states do not allow the

exclusion or limitation of consequential or incidental

damages, the above limitation may not apply to you.

THIS WARRANTY IS GIVEN IN LIEU OF ALL

OTHER WARRANTIES, WRITTEN OR ORAL,

WHETHER EXPRESSED BY AFFIRMATION,

PROMISE, DESCRIPTION, DRAWING, MODEL

OR SAMPLE. ANY AND ALL WARRANTIES

OTHER THAN THIS ONE, WHETHER EXPRESS

OR IMPLIED, INCLUDING IMPLIED

WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE

HEREBY DISCLAIMED.

• This Limited Warranty is the only warranty that

Brother is giving for this Product. It is the final

expression and the exclusive and only statement of

Brother’s obligations to you. It replaces all other

agreements and understandings that you may have

with Brother or its representatives.

• This warranty gives you certain rights and you

may also have other rights that may vary from state

to state.

• This Limited Warranty (and Brother’s obligation

to you) may not be changed in any way unless you

and Brother sign the same piece of paper in which

we (1) refer to this Product and your bill of sale

date, (2) describe the change to this warranty and

(3) agree to make that change.

Important:

We recommend that you keep all original packing

materials, in the event that you ship this product.

v

Important Information

Should you have questions, or need information about

your Brother Product, we have a variety of support

options for you to choose from:

USA-Customer Service:

Customer Service

877-478-6824 (voice)

Customer Service

901-379-1210 (fax)

Automated Faxback

800-521-2846

World Wide Web

www.brother.com

Supplies / Accessories

www.brothermall.com

or 888-879-3232

BROTHER INTERNATIONAL CORPORATION

100 SOMERSET CORPORATE BLVD.

BRIDGEWATER, NEW JERSEY 08807-0911

Please record your model and serial number and your

date and location of Purchase below for your records.

Keep this information with your proof of purchase (bill

of sale) in case your Product requires service.

Model #

Serial #

Date of purchase:

Store where purchased:

Location of store:

Important: We recommend that you keep all original

packing materials, in the event you ship this product.

Save Time - Register On-Line!

Don’t stand in line at the post office or worry about lost mail. Visit us on-line at

www.registermybrother.com

Your product will immediately be registered in our database and you can be on your way!

Also, while you're there, look for contests and other exciting information!

vi

1

Getting Started

1

Getting Started

General Description

Top view & bottom view

Tape cutter button

Keyboard

AC adapter connector

Display

Back cover

Cassette release lever

Print head

Tape exit slot

Tape cassette compartment

Battery compartment

Top view

Bottom view

2

Keyboard & LCD display

1 Left text alignment (page 28)

2 Center text alignment (page 28)

3 Right text alignment (page 28)

4 Justified text alignment

(page 28)

5 Bold text style (page 27)

6 Outline text style (page 27)

7 Italic text style (page 27)

8 Frame (page 24)

9 Low battery (page 5)

0 Block number (page 16)

A Label Type setting (page 9)

B Width setting (page 26)

C Size setting (pages 25 & 26)

D Length setting (page 23)

E Caps mode (page 15)

F Insert mode (page 16)

G Shift mode (page 15)

H Code mode (page 15)

I Power key (page 8)

J Backspace key

(pages 14 & 17)

K Arrow keys (page 14)

L Return key (pages 14 & 16)

M Global format key (pages 25)

N Auto Format keys (page 29)

O Feed key (page 30)

P Print key (page 30)

Q Label Type (page 9)

162

3

4

5

7

8

9

0

A

BC

D

E

F

H

I

G

J

L

K

M

N

O

P

Q

PT-1400

3

Getting Started

General Precautions

● Use only Brother TZ tapes with this machine. Do not use tapes that do not

have the mark.

● Do not pull on the tape being fed from the P-touch, otherwise the tape cassette may

be damaged.

● Avoid using the machine in extremely dusty places. Keep it out of both direct

sunlight and rain.

● Do not expose the machine to extremely high temperatures or high humidity.

Never leave it on the dashboard or in the back of your car.

● Do not store tape cassettes where they would be exposed to direct sunlight, high

humidity or dust.

● Do not leave any rubber or vinyl on the machine for an extended period of time,

otherwise the machine may be stained.

●

Do not clean the machine with alcohol or other organic solvents. Only use a soft, dry cloth.

● Do not put any foreign objects into or heavy objects on the machine.

● To avoid injuries, do not touch the cutter’s edge.

● Use only the AC adapter designed exclusively for this machine. Use of any other

adapter will void the warranty.

● Do not try to disassemble the AC adapter.

●

When the machine is not to be used for a long period of time, disconnect the AC adapter,

and remove the batteries to prevent them from leaking and damaging the machine.

● Use six AA alkaline or rechargeable (Ni-Cd or Ni-MH) batteries.

● Never try to disassemble the P-touch.

4

Batteries & Tape Cassettes

This machine has been designed to allow you to change the batteries and tape cassettes

quickly and easily. With batteries installed, this compact and portable machine can be

used anywhere. TZ tape cassettes are available for this machine in a wide variety of

types, colors and sizes, enabling you to make distinctive color-coded and stylized labels.

Installing batteries and a tape cassette

Notes on batteries

☞ This P-touch requires six AA-size batteries. Rechargeable (Ni-Cd or

Ni-MH) batteries can be used instead of six alkaline batteries.

☞ The rechargeable batteries cannot be recharged by leaving them in the P-touch with the

AC adapter connected. Instead, recharge the batteries by using a battery charger

designed specifically for the type of batteries used. For more details on the rechargeable

batteries, refer to the instructions provided with them.

☞ Do not use any of the following, otherwise battery leakage or damage may occur.

• Manganese batteries

• A combination of new and used batteries

• A combination of batteries of different types (alkaline, Ni-Cd and Ni-MH),

different manufacturers or different models

• A combination of recharged and uncharged batteries

2

1

5

Getting Started

☞ Make sure that the batteries are inserted so that their poles point in the correct direction.

With batteries installed, the P-touch determines the remaining battery charge during

printing and feeding. If a low battery charge is detected, the low battery indicator ())

comes on. When this occurs, be sure to replace the batteries. The low battery indicator

may not come on in some operating conditions.

☞ Before replacing the batteries, make sure that the P-touch is turned off. In addition, when

replacing the batteries, insert the new ones within five minutes of removing the old ones,

otherwise the text shown in the display and any text stored in the memory will be lost.

☞ If you do not intend to use this P-touch for an extended period of time, remove the

batteries. When the power is disconnected, all text shown in the display and stored in the

memory will be lost.

☞ Since the enclosed batteries begin discharging from the time that the unit is shipped from

the factory, their life span may not meet specifications, depending on when the unit is

put into use.

Notes on tape cassettes

☞ Before installing the tape cassette, make sure that the end of the tape feeds under the tape

guides. If the tape cassette to be installed has an ink ribbon and the ink ribbon is loose,

use your finger to wind the toothed wheel in the direction of the arrow on the cassette

until there is no slack in the ribbon.

☞ When inserting the tape cassette, make sure that the inner ribbon does not catch on the

corner of the metal guide.

☞ After installing a tape cassette, press f once to remove any slack in the tape, and then

press in on the tape cutter button to cut off the excess tape.

☞ Always cut off the tape before removing it from the machine. If the tape is pulled on

before being cut off, the tape cassette may be damaged.

End of the tape Tape guides

6

Extra Strength Adhesive Tape

☞ For textured, rough, or slippery surface, we recommend using Extra Strength Adhesive

Tape.

☞ Although the instruction sheet included with the Extra Strength Adhesive

Tape cassette recommends cutting the tape with scissors, the tape cutter

that this P-touch is equipped with is able to cut Extra Strength Adhesive

Tape.

Flexible ID Tape

☞ For applications that require more flexible labels, such as around sharp bends and

cylindrical objects, we recommend using Flexible ID Tape.

☞ Labels made with Flexible ID Tape are not designed for use as electrical insulation.

☞ When wrapping labels around cylindrical objects, the diameter of the object should be at

least 1/8" (3 mm), otherwise the label should be wrapped as a flag and the FLAG Label

Type mode should be used. In addition, the overlapping ends of the label or the label flag

should be at least 3/16" (5 mm).

☞ The label may peel off cylindrical objects if the object is bent after the label is affixed.

Diameter > 3 mm

Overlap > 5 mm

Flag > 5 mm

7

Getting Started

Cleaning

Occasionally, certain parts of the P-touch may need to be cleaned. Dust or dirt may

become attached to the P-touch’s print head and rollers, particularly when the unit is

used outdoors or in a very dusty environment. With use, the tape cutter may become

covered with adhesive, making it difficult to cut the tape.

Cleaning the print head, rollers and tape cutter

Notes on cleaning the print head & rollers

☞ If a blank horizontal streak appears through the label text, clean the machine’s print

head.

☞ The print head can be cleaned more easily if the optional print head cleaning cassette

(TZ-CL4) is used.

☞ Before cleaning the print head and rollers, press o to turn off the P-touch, and then

remove the batteries and disconnect the optional AC adapter.

☞ Be extremely careful not to touch the cutter blades with your fingers.

Dry Cotton swab

Print head

Dry Cotton swab

Tape cutter blades

Dry cotton swab

Tape cutter blades

8

Notes on cleaning the tape cutter

☞ If the tape cannot be cut correctly, clean the tape cutter blades.

Optional AC Adapter

When printing a large number of labels or labels that contain a large amount of text, it may be

useful to connect the P-touch to a standard electrical outlet using the optional AC adapter.

Connecting the AC adapter

Notes on the AC adapter

☞ Only use the AC adapter designed exclusively for this machine.

☞ Disconnect the AC adapter if you do not intend to use this P-touch for an extended

period of time. When the power is disconnected, all text shown in the display and stored

in the memory will be lost.

Turning the P-touch On/Off

Press o to turn on or turn off the P-touch.

If batteries are installed or the P-touch has remained plugged in using the AC adapter,

the previous session’s text is displayed when the P-touch is turned on again. This feature

allows you to stop work on a label, turn off the machine, and return to it later without

having to re-enter the text.

Regardless of whether the P-touch is being operated from batteries or the AC adapter,

the machine will automatically turn off if no key is pressed or no operation is performed

for 5 minutes.

1

DC IN 9-9.5V

2

9

Label Type Modes

2

Label Type Modes

Selecting a Label Type Mode

Pressing

a

allows you to select one of the two regular modes for designing and printing

your own custom labels, or any of the five special modes available for printing labels pre-

formatted for identifying patch panels, cables, connectors and other components.

1 Press a.

2 Press u or d (or continue pressing a) until the desired mode is

displayed. (For details on each Label Type mode, refer to the sections below.)

3 Press n to apply the selected Label Type mode.

• If NORMAL or VERTICAL was selected, continue entering the label text as

described in chapter 3, Basic Functions.

• If ROTATE, ROT-REP, PORT, PANEL, or FLAG was selected, continue

with the following steps.

4 Press l or r until the desired parameter is displayed.

5 Press u or d until the desired setting is displayed (or use the number keys

to type in the desired setting).

6 Press n to apply the selected settings.

7 Type the text for each label in a separate text block.

8 Print the labels.

• To print a single copy of each label, press p.

• To print multiple copies or several copies while increasing certain characters, or to

print using any other special printing function, press

g

, then

a

and choose

your options. (For details, refer to

Using special printing functions

on page 31.)

Normal and Vertical Modes

Labels printed using the Normal and Vertical Label Type

modes can be formatted and printed to fit any need.

ABCDE

NORMAL

VERTICAL

A

B

C

D

E

10

After selecting the Label Type mode NORMAL or VERTICAL, the label text can be

entered, formatted, printed and cut as usual. With the Normal Label Type mode, the

entered text is printed horizontally along the label. With the Vertical Label Type mode,

the entered text is printed vertically along the label.

Rotate Mode and Rotate & Repeat Mode

Labels printed using these Label Type modes can be wrapped

around cables and wires to mark them. With both of these

modes, the text is rotated 90° counterclockwise and each text

block printed on a separate label as shown below. With the

Rotate & Repeat mode, the text is printed repeatedly along

the length of the label so that it can easily be read from any

angle.

After selecting the ROTATE or ROT-REP Label Type mode, specify the length of

each label and a frame style if desired.

● BLK LEN. (block length): 0.80" to 8.00" (20 to 200 mm)

Default: 1.20" (30 mm)

● FRAME: OFF, , , ,

Default: OFF

☞ A single block of text can contain a maximum of 7 text lines, and with the ROT-REP

Label Type mode, only the text lines that fit within the label are printed.

☞ For labels to be attached to cables and wires, we recommend using Flexible ID Tape.

When wrapping Flexible ID Tape around cylindrical objects, the diameter of the

object should be at least 1/8" (3 mm), otherwise the FLAG Label Type mode should

be used. In addition, the overlapping ends of the label or the flag length should be at

least 3/16" (5 mm).

Rotate

&

Repeat

Block length

Block lengthBlock length

1 2

3 4

11

Label Type Modes

Flag Mode

Labels printed using this Label Type mode can be wrapped

around cable or wire with the ends stuck together to form a

flag. With the FLAG Label Type mode, each block of text is

printed at both ends of separate labels. The length of the

unprinted part of this label is equal to the circumference of

the cable or wire. In addition, the text can be printed

horizontally or rotated 90°.

After selecting the FLAG Label Type mode, specify the length and diameter of the flag,

a frame style if desired, and whether or not to rotate the text.

● FLAG (flag diameter): 0.00" to 4.00" (0 to 100 mm)

Default: 0.25" (7 mm)

● FLAG LEN (flag length): 0.40" to 8.00" (10 to 200 mm)

Default: 1.20" (30 mm)

● FRAME: OFF, , , ,

Default: OFF

● ROTATE: OFF, ON

Default: OFF

☞ A single block of text can contain a maximum of 7 text lines.

☞ For labels to be attached to cables and wires, we recommend using Flexible ID Tape.

To wrap Flexible ID Tape around cylindrical objects, use the FLAG Label Type

mode when the diameter of the object is less than 1/8" (3 mm). In addition, the flag

length should be at least 3/16" (5 mm).

ROTATE

set to

OFF

ROTATE

set to

ON

Flag

length

Flag

diameter

Flag

length

Flag

length

Flag

diameter

Flag

length

1 2

3 4

12

Port & Panel Modes

Labels printed using these Label Type modes can be used to identify various

components or panels.

With the Port Label Type mode, each block of

the text is printed on a separate label, making

these labels useful for identifying different

components or ports that are not equally spaced.

With the

Panel

Label Type mode, all blocks of

the text are evenly spaced on a single label,

making this label useful for a row of equally

spaced switches, fuses or connectors on a patch

panel. In addition, the text blocks can be printed

in the order that they were typed in or in the

opposite order.

After selecting the PORT or PANEL Label Type mode, specify the length of each text

block or label, and select a frame style if desired. For the PANEL Label Type mode,

select whether the text blocks are printed in the order that they were typed in or in the

reverse order.

FRONT REVERSE

Port

Panel

(PRINT set

to FRONT)

Panel

(PRINT set

to REVERSE)

Block length

Block length Block length

Block length Block lengthBlock length

La pagina sta caricando ...

Brother P-touch 1400 Guida utente

Questo manuale è adatto anche per

Brother P-touch 1400 Guida utente

in altre lingue

Documenti correlati

Altri documenti