Hikoki CS1825DC Manuale utente

CS 1825DC

en

de

fr

it

nl

es

pt

sv

da

no

ﬁ

el

pl

hu

cs

tr

ro

sl

sk

bg

sr

hr

pt

sv

da

no

ﬁ

sl

sk

bg

sr

hr

Handling instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

Bruksanvisning

Brugsanvisning

Bruksanvisning

Käyttöohjeet

Οδηγίες χειρισμού

Instrukcja obsługi

Kezelési utasítás

Návod k obsluze

Kullanım talimatları

Instrucţiuni de utilizare

Navodila za rokovanje

Pokyny na manipuláciu

Инструкция за експлоатация

Uputstvo za rukovanje

Upute za rukovanje

en

de

fr

it

nl

es

el

pl

hu

cs

tr

ro

2

1

AC

G

E

I

B

D

H

F

KM

L

J

N

OPQ2

345

6 7

3

8 9

10

11 12

13 14 15

0.5–

1 mm

4

16 17

18 19 20

21 22 23

24 25 26

5

27 28 29

30 31 32

33 34

35 36 37

6

38 39 40

41 42

43 44

7

English

(Original instructions)

SYMBOLS

WARNING

The following show symbols used for the machine.

Be sure that you understand their meaning before

use.

CS1825DC: Cordless Chain Saw

To reduce the risk of injury, user must read

instruction manual.

Do not use a power tool in the rain and

moisture or leave it outdoors when it is raining.

Only for EU countries

Do not dispose of electric tools together with

household waste material!

In observance of European Directive

2012/19/EU on waste electrical and electronic

equipment and its implementation in

accordance with national law, electric tools

that have reached the end of their life must

be collected separately and returned to an

environmentally compatible recycling facility.

Read, understand and follow all warnings and

instructions in this manual and on the unit.

Always wear eye, head and ear protectors

when using this unit.

Beware of chain saw kickback and avoid

contact with bar tip.

Always use chain saw two-handed.

It is important that you wear the protective

clothing for feet, legs, hands, fore-arms and

head.

This chain saw is for use by trained tree service

operator only. Use without proper training can

result in severe injuries.

Chain oil delivery rate adjustment

Disconnect the battery

WHAT IS WHAT? (Fig. 1)

A: Battery (sold separately): Power source to drive the

unit.

B: Switch: Device activated by the ﬁ nger.

C: Lock-oﬀ lever: Lever that prevents the accidental

operation of the trigger.

D: Chain brake: Device for stopping or locking the saw

chain.

E: Side cover: Protective cover to the guide bar, saw

chain, clutch and sprocket when the chain saw is in

use.

F: Nut: Nut for securing side cover.

G: Tensioning screw: Device for adjusting tension of saw

chain.

H: Front handle: Support handle located at or towards the

front of the main body.

I: Rear handle (Top handle): Support handle located on

the rear of the main body.

J: Saw chain: Chain, serving as a cutting tool.

K: Guide bar: The part that supports and guides the saw

chain.

L: Oil tank cap: Cap for closing the oil tank.

M: Oil sight glass: Window to check chain oil amount.

N: Hook: Tool for hanging the unit with rope etc.

O: Oil feeder: Container for oil.

P: Chain case: Case for covering the guide bar and saw

chain when the unit is not being used.

Q: Combi box spanner: The tool for removing or installing

a side cover and tensioning the saw chain.

WARNING

This chain saw (CS1825DC) is designed especially

for tree care and surgery. Only persons trained in

tree care and surgery may use this saw. Observe all

literature, procedures and recommendations from

the relevant professional organization. Failure to do

so constitutes a high accident risk. We recommend

always using a rising platform for sawing in trees.

Rappelling techniques are extremely dangerous and

require special training. The operator must be trained

in and familiar with the use of safety equipment and

working and climbing techniques. Always use the

restraining equipment for both the operator and the

saw.

GENERAL POWER TOOL SAFETY

WARNINGS

WARNING

Read all safety warnings, instructions, illustrations

and speciﬁ cations provided with this power tool.

Failure to follow all instructions listed below may result in

electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future

reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the dust

or fumes.

8

English

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as a dust mask, non-

skid safety shoes, hard hat or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts.

Loose clothes, jewellery or long hair can be caught

in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles.

A careless action can cause severe injury within a

fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any

adjustments, changing accessories, or storing

power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may aﬀ ect the power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions and

the work to be performed.

Use of the power tool for operations diﬀ erent

from those intended could result in a hazardous

situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by

the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with

another battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

9

English

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂ ush with water. If

liquid contacts eyes, additionally seek medical

help.

Liquid ejected from the battery may cause irritation

or burns.

e) Do not use a battery pack or tool that is

damaged or modiﬁ ed.

Damaged or modiﬁ ed batteries may exhibit

unpredictable behaviour resulting in ﬁ re, explosion

or risk of injury.

f) Do not expose a battery pack or tool to ﬁ re or

excessive temperature.

Exposure to ﬁ re or temperature above 130°C may

cause explosion.

g) Follow all charging instructions and do

not charge the battery pack or tool outside

the temperature range speciﬁ ed in the

instructions.

Charging improperly or at temperatures outside

the speciﬁ ed range may damage the battery and

increase the risk of ﬁ re.

6) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

b) Never service damaged battery packs.

Service of battery packs should only be performed

by the manufacturer or authorized service

providers.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach

of children and inﬁ rm persons.

CORDLESS CHAIN SAW SAFETY

WARNINGS

1) General chain saw safety warnings

a) This chain saw is not intended for tree felling.

Use of the chain saw for operations diﬀ erent than

intended could result in serious injury to the operator or

bystanders.

b) The operator must be trained in safe climbing

techniques and in the use of all recommended

additional safety equipment, such as harness,

loops, straps, rope and karabiners, and other

fall arrest systems for the operator and the saw.

Establishing a secure location in the tree at each

working position is essential to avoid a hazardous

situation.

c) Wear eye protection, ear protection and protective

equipment for head, forearms, hands, legs and feet

that is suitable for tree climbing. Adequate protective

equipment will reduce personal injury from ﬂ ying debris

or accidental contact with the saw chain.

d) Cut wood only. Do not use chain saw for purposes

not intended. For example: do not use chain saw

for cutting metal, plastic, masonry or non-wood

building materials. Use of the chain saw for operations

diﬀ erent than intended could result in a hazardous

situation.

e) Always hold the chain saw with your right hand

on the rear handle and your left hand on the front

handle. Holding the chain saw with a reversed hand

conﬁ guration increases the risk of personal injury and

should never be done.

f) Hold the chain saw by insulated gripping surfaces

only, because the saw chain may contact hidden

wiring. Saw chains contacting a "live" wire may make

exposed metal parts of the chain saw "live" and could

give the operator an electric shock.

g) Keep all parts of the body away from the saw chain

when the chain saw is operating. Before you start

the chain saw, make sure the saw chain is not

contacting anything. A moment of inattention while

operating chain saws may cause entanglement of your

clothing or body with the saw chain.

h) When cutting a limb that is under tension, be alert

for spring back. When the tension in the wood ﬁ bres

is released, the spring loaded limb may strike the

operator and/or throw the chain saw out of control.

i) Use extreme caution when cutting thin branches.

The slender material may catch the saw chain and be

whipped toward you or pull you oﬀ balance.

j) Follow all instructions when clearing jammed

material, storing or servicing the chain saw.

Make sure the switch is oﬀ and the battery pack

is removed. Unexpected actuation of the chain saw

while clearing jammed material or servicing may result

serious personal injury.

k) Carry the chain saw by the front handle with the

chain saw switched oﬀ and away from your body.

When transporting or storing the chain saw, always

ﬁ t the guide bar cover. Proper handling of the chain

saw will reduce the likelihood of accidental contact with

the moving saw chain.

l) Follow instructions for lubricating, chain tensioning

and changing the bar and chain. Improperly

tensioned or lubricated chain may either break or

increase the chance for kickback.

2) Causes and operator prevention of kickback:

Kickback may occur when the nose or tip of the guide

bar touches an object, or when the wood closes in and

pinches the saw chain in the cut. (Fig. 2)

Tip contact in some cases may cause a sudden reverse

reaction, kicking the guide bar up and back towards the

operator.

Pinching the saw chain along the top of the guide

bar may push the guide bar rapidly back towards the

operator.

Either of these reactions may cause you to lose control

of the saw which could result in serious personal

injury. Do not rely exclusively upon the safety devices

built into your saw. As a chain saw user, you should

take several steps to keep your cutting jobs free from

accident or injury.

Kickback is the result of machine misuse and/or

incorrect operating procedures or conditions and can

be avoided by taking proper precautions as given

below:

a) Maintain a ﬁ rm grip, with thumbs and ﬁ ngers

encircling the chain saw handles, with both hands

on the saw and position your body and arm to allow

you to resist kickback forces. (Fig. 3) Kickback

forces can be controlled by the operator, if proper

precautions are taken. Do not let go of the chain saw.

b) Do not overreach. This helps prevent unintended tip

contact and enables better control of the chain saw in

unexpected situations.

c) Only use replacement guide bars and saw chains

speciﬁ ed by the manufacturer. Incorrect replacement

guide bars and saw chains may cause chain breakage

and/or kickback.

d) Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increased kickback.

10

English

ADDITIONAL SAFEY WARNINGS

1. Work without pressure. In addition, always keep your

body warm.

2. Keep all parts of the body away from the saw chain

when the chain saw is operating.

3. Before commencing work, reﬂ ect fully on the work

procedures involved and work to avoid accidents,

otherwise injury may occur.

4. Do not use in the event of bad weather, such as strong

wind, rain, snow, fog, or in areas prone to rockfall or

avalanches.

In bad weather, judgment may be impaired and the

vibration may result in disaster.

5. When visibility is poor, such as during bad weather or

night, do not use the unit. In addition, do not use it in

rain or in a location exposed to rain.

Unstable foothold or loss of balance may result in an

accident.

6. Check the guide bar and saw chain before starting the

unit.

○ If the guide bar or saw chain is cracked, or the product

is scratched or bent, do not use the unit.

○ Check if the guide bar and saw chain are securely

installed. If the guide bar or saw chain is broken or

dislodged, this may result in an accident.

7. Before starting work, check to ensure the switch does

not engage unless the lock-oﬀ lever is pressed.

If the unit does not working properly, immediately stop

using and request repair from your HiKOKI Authorized

Service Center.

8. Install the saw chain properly, in accordance with the

instruction manual.

If installed incorrectly, the saw chain will come oﬀ the

guide bar and injury may occur.

9. Never remove any of the safety devices equipped on

the chain saw (chain brake, lock-oﬀ lever, chain catcher

etc.).

In addition, do not alter or immobilize them.

Injury may occur.

10. In the following cases, switch the unit oﬀ and ensure

the saw chain is no longer moving:

○ When not in use.

○ When shifting to a new work location.

○ When inspecting, adjusting or replacing the saw chain,

guide bar, chain case and any other part.

○ When reﬁ lling the chain oil.

○ When removing dust etc. from the body.

○ When removing obstacles, trash or sawdust generated

from work from the work area.

○ When you take oﬀ the unit, or when you get away from

the unit.

○ Otherwise, if you sense danger or anticipate risk.

If the saw chain is still moving, an accident may occur.

11. Work should generally be performed individually.

When multiple individuals are involved, ensure

suﬃ cient spacing between them.

12. Remain more than 15 m away from other people.

In addition, when working with multiple persons,

remain 15 m or more apart.

○ There is a risk of impact with scatters and other

accidents.

○ Prepare a whistle alert etc. and determine appropriate

contact method for other workers beforehand.

13. Before cutting standing trees, ensure the following:

○ Determine a safe evacuation location prior to cutting.

○ Remove obstacles (e.g., branches, shrubs) in advance.

14. During use, if the unit performance deteriorates, or you

notice any abnormal sound or vibration, immediately

switch oﬀ and discontinue use, and return to your

HiKOKI Authorized Service Center for inspection or

repair.

If you continue using, injury may occur.

15. If the unit is accidentally dropped or exposed to impact,

inspect carefully for damage or cracks and ensure

there is no deformation.

If the unit is damaged, cracked or deformed, injury may

occur.

16. When transporting the unit by car, secure the unit to

prevent it moving.

There is a risk of accident.

17. Do not switch the unit on while the chain case is

attached.

Injury may occur.

18. Ensure there are no nails and other foreign objects in

the material.

If the saw chain impact on the nail etc., injury may

occur.

19. To avoid the guide bar becoming entangled with the

material when chopping on a verge or when subject to

the weight of material while cutting, install a supporting

platform close to the cutting position.

If the guide bar becomes entangled, injury may occur.

20. If the unit is to be transported or stored after use, either

remove the saw chain, or attach the chain case.

If the saw chain comes into contact with your body,

injury may occur.

21. Adequately care for the unit.

○ To ensure work can be performed safely and eﬃ ciently,

care for the saw chain to ensure it provides optimal

cutting performance.

○ When replacing the saw chain or guide bar, maintaining

the body, ﬁ lling oil etc., follow the instruction manual.

22. Ask the shop to repair the unit.

○ Do not modify this product, since it already complies

with the applicable safety standards.

○ Always refer to your HiKOKI Authorized Service Center

for all repairs.

Attempting to repair the unit yourself may result in an

accident or injury.

23. When not using the unit, ensure it is properly stored.

Drain oﬀ the chain oil, and keep in a dry place out of

reach of children or a locked location.

24. If the warning label is no longer visible, peels oﬀ or is

otherwise unclear, apply a new warning label.

For the warning label, refer to your HiKOKI Authorized

Service Center.

25. When working, if local rules or regulations apply,

comply with the same.

26. Make sure that the battery is installed ﬁ rmly. If it is at all

loose it could come oﬀ and cause an accident.

27. Do not use the product if the tool or the battery terminals

(battery mount) are deformed.

Installing the battery could cause a short circuit that

could result in smoke emission or ignition.

28. Keep the tool’s terminals (battery mount) free of swarf

and dust.

○ Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○ During use, try to avoid swarf or dust on the tool from

falling on the battery.

○ When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling

swarf or dust.

Doing so could cause a short circuit that could result in

smoke emission or ignition.

29. Always use the tool and battery at temperatures

between -5°C and 40°C.

11

English

PRECAUTIONS FOR BATTERY AND

CHARGER (sold separately)

1. Always charge the battery at a temperature of

0°C–40°C. A temperature of less than 0°C will result in

over charging which is dangerous. The battery cannot

be charged at a temperature higher than 40°C.

The most suitable temperature for charging is that of

20°C–25°C.

2. Do not use the charger continuously.

When one charging is completed, leave the charger for

about 15 minutes before the next charging of battery.

3. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

4. Never disassemble the rechargeable battery or

charger.

5. Never short-circuit the rechargeable battery.

Short-circuiting the battery will cause a great electric

current and overheat. It results in burn or damage to the

battery.

6. Do not dispose of the battery in ﬁ re.

If the battery is burnt, it may explode.

7. Using an exhausted battery will damage the charger.

8. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery life

becomes too short for practical use. Do not dispose of

the exhausted battery.

9. Do not insert objects into the air ventilation slots of the

charger.

Inserting metal objects or ﬂ ammable into the charger

air ventilation slots will result in an electrical shock

hazard or damage to the charger.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes of

overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○ During work make sure that swarf and dust do not fall

on the battery.

○ Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○ Do not store an unused battery in a location exposed to

swarf and dust.

○ Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject the

battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery for a purpose other than those

speciﬁ ed.

5. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately

stop further recharging.

6. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven, dryer,

or high pressure container.

7. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

8. Do not use in a location where strong static electricity

generates.

9. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears abnormal

during use, recharging or storage, immediately remove

it from the equipment or battery charger, and stop use.

10. Do not immerse the battery or allow any ﬂ uids to ﬂ ow

inside. Conductive liquid ingress, such as water, can

cause damage resulting in ﬁ re or explosion. Store your

battery in a cool, dry place, away from combustible and

ﬂ ammable items. Corrosive gas atmospheres must be

avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using the

battery for the ﬁ rst time, do not use and return it to your

supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of ﬁ re. Please observe the

following matters when storing the battery.

○ Do not place electrically conductive cuttings,

nails, steel wire, copper wire or other wire in the

storage case.

○ Either install the battery in the power tool or store

by securely pressing into the battery cover until

the ventilation holes are concealed to prevent

short-circuits (See Fig. 4).

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe

the following precautions.

WARNING

Notify the transporting company that a package contains a

lithium-ion battery, inform the company of its power output

and follow the instructions of the transportation company

when arranging transport.

○ Lithium-ion batteries that exceed a power output of

100 Wh are considered to be in the freight classiﬁ cation

of Dangerous Goods and will require special

application procedures.

○ For transportation abroad, you must comply with

international law and the rules and regulations of the

destination country.

12

English

Power Output

2 to 3 digit number

NAMES OF PARTS (Fig. 1–Fig. 44)

Battery

(sold separately) Oil sight glass

Latch Oil pump adjuster

Ventilation holes Chain brake

Terminals Actuation

Battery cover Release

Insert Battery level indicator

switch

Pull out Battery level indicator

lamp

Lock-oﬀ lever Spike

(sold separetly)

Switch Rear handle

(Top handle)

Pilot lamp Front handle

Combi box spanner Round ﬁ le

Side cover 1/5 of diameter of ﬁ le

Nut Depth gauge jointer

Tensioning screw Flat ﬁ le

Increase the tension Protruding depth

gauge head

Decrease the tension Round oﬀ

Saw chain Chain oil spout

Guide bar Groove

Sprocket Oil hole

Blade direction Chain catcher

Illustration showing

blade direction Battery sliding

grooves

Bolt Terminal

(Product)

Chain tensioner boss Air blow gun

Lug Terminal (Battery)

Guide bar tip Sliding grooves

Drive link Hook

Chain oil

SPECIFICATIONS

1. Power tool

Model CS1825DC

Voltage 18 V

Saw chain Type: 90PX-040X

Pitch: 9.5 mm (3/8")

Gauge: 1.1 mm (0.043")

Guide bar Type: 104MLEA041

Size: 250 mm

(Max. cutting legth)

Sprocket Number of teeth: 6

Pitch 9.5 mm (3/8")

No-load chain speed 12.1 m/s (730 m/min)

Chain oil tank

capacity 70 ml

Battery available for

this tool

BSL1820M, BSL1830C,

BSL1840M, BSL1850,

BSL1850C, BSL1850MA,

BSL36A18, BSL36B18

Weight* 2.0 kg

* Weight: Saw chain, guide bar, chain case, oil, battery

not included

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

2. Battery (sold separetly)

Model BSL1820M

Voltage 18 V

Battery capacity 2.0 A

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains

the accessories listed on page 322.

Standard accessories are subject to change without

notice.

APPLICATIONS

○ Cutting of timber/logs

○ Pruning of garden trees

CHARGING

Battery and battery charger are not included with this

product.

Before using the power tool, charge the battery as follows.

1. Connect the charger’s power cord to the

receptacle.

When connecting the plug of the charger to a

receptacle, the pilot lamp will blink in red (At 1- second

intervals).

2. Insert the battery into the charger.

Firmly insert the battery into the charger as shown in

Fig. 6.

13

English

3. Charging

When inserting a battery in the charger, charging will

commence and the pilot lamp will light continuously in

red.

When the battery becomes fully recharged, the pilot

lamp will blink in red. (At 1-second intervals) (See

Table 1)

● Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 1, according to the condition of the charger or

the rechargeable battery.

Table 1

Indications of the pilot lamp (RED)

Before

charging

Lights on for

0.5 seconds and oﬀ

for 0.5 seconds

Blinks

Plugged into power

source

While

charging

Lights continuously

Lights —

Charging

complete

Lights on for

0.5 seconds and oﬀ

for 0.5 seconds

Blinks —

Overheat

standby

Lights on for

1 second and oﬀ for

0.5 seconds

Blinks

Battery overheated.

Unable to charge.

(Charging will

commence when

battery cools)

Charging

impossible

Lights on for

0.1 seconds and oﬀ

for 0.1 seconds

Flickers

Malfunction in

the battery or the

charger

● Regarding the temperatures and charging time of the

battery.

The temperatures and charging time will become as

shown in Table 2.

Table 2

Charger

Battery UC18YFSL

Charging voltage V 14.4–18

Weight kg 0.5

Temperatures at which the battery

can be recharged 0°C–50°C

Charging time for battery

capacity, approx. (At 20°C)

1.5 Ah

2.0 Ah

2.5 Ah

3.0 Ah

4.0 Ah

5.0 Ah

6.0 Ah

8.0 Ah

min

22

30

35

45

60

75

90

120

Number of battery cells 4–10

NOTE

The recharging time may vary according to temperature

and power source voltage.

CAUTION

When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after

use, and then keep it.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might be

low when using them the ﬁ rst and second time. This is a

temporary phenomenon, and normal time required for

recharging will be restored by recharging the batteries

2–3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the battery

and recharge it after it has cooled for a while.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery has just been used,

the pilot lamp of the charger lights for 1 second, does

not light for 0.5 seconds (oﬀ for 0.5 seconds). In such a

case, ﬁ rst let the battery cool, then start charging.

○ When the pilot lamp ﬂ ickers (at 0.2-second intervals),

check for and take out any foreign objects in the

charger’s battery connector. If there are no foreign

objects, it is probable that the battery or charger is

malfunctioning. Take it to your authorized Service

Center.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the battery 5 2

Switch operation*172

Using the hook*244 6

Selecting accessories ―323

*1 Switch operation

When the switch is engaged while sliding the lock-oﬀ

lever, the saw chain rotates. (Fig. 7)

Unless the lock-oﬀ lever is being slid, the switch cannot

be engaged.

14

English

After the switch is engaged, the saw chain continues

rotating as long as it is pressed down.

When the switch is released, a brake is applied to stop

the saw chain rotation.

WARNING

Do not secure the lock-oﬀ lever in the slid position.

If the switch is accidentally engaged, the unit may

unexpectedly start and injury may occur.

*2 Using the hook

WARNING

When using the hook, ensure the unit is securely

suspended to avoid the risk of falling.

If the unit falls, an accident may occur.

INSTALLING (REPLACING) SAW

CHAIN

WARNING

○ To prevent accidents, always switch the unit oﬀ , and

remove the battery.

○ Don't use the saw chain or the guide bar other than

those speciﬁ ed in “SPECIFICATIONS”.

CAUTION

Wear thick gloves and be careful to avoid injury with the

saw chain.

NOTE

○ When removing the saw chain, remove sawdust from

the oil spout, oil hole, and guide bar groove.

If sawdust accumulates, this may cause the unit to fail.

○ Use the correct type of saw chain in accordance with

the speciﬁ cations.

If you install the wrong type of guide bar, the saw chain

may come oﬀ and injury may occur.

1. Removing the side cover (Fig. 8)

Turn the nut and remove the side cover.

2. Removing the saw chain and guide bar (Fig. 9)

Rotate the tensioning screw in the “-” direction to

introduce a small amount of slack in the saw chain,

then detach from the sprocket. Detach along with the

guide bar in the direction indicated by the arrow.

3. Engaging the new saw chain in the sprocket

(Fig. 10)

Attach the saw chain from the guide bar tip. Make sure

the saw chain is oriented so that the blade faces in the

direction shown in the illustration below the sprocket.

Insert the bolt and chain tensioner boss into the hole in

the guide bar while holding the chain and guide bar tip.

Engage the end of the saw chain to the sprocket and

mount the guide bar to the saw body.

4. Installing the side cover (Fig. 11)

Attach the side cover by inserting the lug into the slot in

the saw body. Make sure the saw chain does not come

loose from the guide bar.

Rotate the nut once to temporarily ﬁ x it.

Remove any dirt around the side cover before

reattaching.

5. Adjusting the saw chain tension (Fig. 12)

○ While lifting the guide bar tip, turn the tensioning screw

to adjust the saw chain tension.

○ Turn the tensioning screw to the "+" to increase the saw

chain tension, and to the "-" to decrease it.

6. Checking the saw chain tension (Fig. 13)

Adjust the saw chain tension so that the gap between

the saw chain drive link and the guide bar is 0.5 to 1 mm

when you lift the saw chain slightly near the center of

the guide bar.

7. Securing the nut (Fig. 14)

When adjustment is complete, lift up the guide bar, and

fully tighten the nut.

WARNING

After adjusting the saw chain tension, ensure the nut is

fully tightened.

If it is loose, injury may occur.

INSPECTION AND PREPARATION

PRIOR TO USE

Prior to use, make the following inspection and preparation.

WARNING

○ To prevent accidents, always perform steps 1 to 3

ensuring the battery is removed from the body.

○ Do not secure the lock-oﬀ lever in the slid position.

If the switch is accidentally engaged, the unit may

unexpectedly start and injury may occur.

1. Ensuring the switch is oﬀ

○ If you insert the battery without knowing whether the

switch is engaged, the unit may unexpectedly start,

which may result in an accident.

○ When the switch is engaged while the lock-oﬀ lever is

in the slid position, the unit switches on, and when the

switch is released, the unit switches oﬀ .

2. Checking the saw chain tension

○ If the saw chain tension is incorrect, there is a risk of

damage to the saw chain or guide bar and malfunction.

Referring to steps 5 to 7 “Installing (replacing) saw

chain,” ensure an appropriate tension is set.

○ While the saw chain is still new, it is particularly

stretchy, so periodically check the tension and adjust

as required.

○ Also check the nut is securely tightened.

3. Checking the chain oil

○ This unit is delivered without chain oil inside. Ensure

the oil tank is ﬁ lled with the chain oil provided before

use. (Fig. 15)

○ Periodically check the oil sight glass during work and

replenish oil as required.

○ If the chain oil supplied runs out, use HiKOKI chain oil

sold separately or equivalent chain oil on the market.

○ The chain oil lubricates automatically.

The discharge rate for auto lubrication is factory preset

to the maximum.

To reduce the discharge rate, turn the oil pump adjuster

on the right side of the oil sight glass clockwise.

(Fig. 16)

NOTE

○ The oil tank capacity is about 70 ml.

Make sure no oil leaks or overﬂ ows from the oil tank

when replenishing the chain oil.

○ We recommend that you stock up with chain oil.

If you continue working without chain oil, the saw chain

may burn through, or the motor may fail.

○ Be careful to avoid dust or other foreign matter from

entering the oil tank.

If dust and other foreign matter enter the oil tank, the

unit may fail.

○ Chain oil left in the tank may leak due to the structure of

this unit. Although this does not indicate a malfunction,

it may soil the storage location, so be careful.

When storing, empty the oil from the oil tank, and place

an item under the main body which can absorb any

leaks.

○ Replenish the oil after every approximately 10 minutes

of operation. (*Varies depending on the cutting usage

conditions)

15

English

4. Installing the battery (Fig. 5)

As shown in Fig. 5, push ﬁ rmly until it clicks into place.

CAUTION

Securely attach the battery.

If the battery is not securely attached, it may come oﬀ

and injury may occur.

5. Checking operation of chain brake (Fig. 17)

WARNING

○ Although the chain brake is an emergency stop device,

this is not completely reliable. Operate carefully to

avoid the risk of kickback.

○ The chain brake is intended for use in emergencies and

when starting up. Do not use it indiscriminately.

○ To avoid impaired movement of the chain brake due to

buildup of sawdust etc., clean regularly.

○ The chain brake is an important component to ensure

safe use.

If you have any concern regarding the chain brake

operation, request repair from your HiKOKI Authorized

Service Center.

The chain brake is an emergency stop device that stops

the saw chain when the unit is subject to kickback etc., to

reduce risk.

(Refer to “Causes and operator prevention of kickback.”)

Push the chain brake in the direction indicated by the arrow

() to apply the chain brake and stop the saw chain. To

release the chain brake, release the switch and pull back

on the chain brake.

CAUTION

The chain brake functions only when power is turned

on. Check chain brake function in a location with no

people or obstructions nearby.

(1) Press the switch while sliding the lock-oﬀ lever.

(2) Once the saw chain begins turning, push the chain

brake forward toward the saw chain.

(3) If the saw chain stops, the chain brake is functioning as

it should. To release the brake, release the switch and

pull back on the chain brake.

6. Checking chain oil discharge (Fig. 18)

○ When switching the unit on, chain oil automatically

lubricates the saw chain and guide bar.

○ If oil does not seem to emerge 2 to 3 minutes after

the unit starts, check if any sawdust has accumulated

around the oil spout.

(Refer to “Cleaning the chain oil spout.”)

(Refer to “Checking the chain oil.”)

7. Installing of the spike (sold separately) (Fig. 19)

When using the spike, refer to “Installing (replacing)

saw chain”, remove the saw chain and guide bar, and

then install the spike with the two screws provided.

REMAINING BATTERY INDICATOR

You can check the battery’s remaining capacity by

pressing the remaining battery indicator switch to light the

indicator lamp. (Fig. 20, Table 3)

The indicator will shut oﬀ approximately 3 seconds after

the remaining battery indicator switch is pressed.

It is best to use the remaining battery indicator as a

guide since there are slight diﬀ erences such as ambient

temperature and the condition of the battery.

Also, the remaining battery indicator may vary from those

equipped to a tool or charger (Battery is not included, sold

separately).

Table 3

State of

lamp Battery Remaining Power

Lights ;

The battery remaining power is over 75%.

Lights ;

The battery remaining power is 50%–75%.

Lights ;

The battery remaining power is 25%–50%.

Lights ;

The battery remaining power is less than

25%.

Blinks ;

The battery remaining power is nearly

empty. Recharge the battery soonest

possible.

Blinks ;

Output suspended due to high temperature.

Remove the battery from the tool and allow

it to fully cool down.

Blinks ;

Output suspended due to failure or

malfunction. The problem may be the

battery so please contact your dealer.

NOTE

Do not give a strong shock to the switch panel or break

it. It may lead to a trouble.

CUTTING PROCEDURES

WARNING

○ When working in trees, wear appropriate protection on

your eyes, head, hands, legs, and arms, as well as slip-

resistant foot protection.

○ Prior to operation, ensure that chain brake works.

○ During use, grip the handle securely with both hands.

(Fig. 3)

○ When cutting timber from the bottom, ensure the saw

chain does not impact with the timber.

If the unit is pushed back, injury may occur.

○ During work breaks or after work, always switch the unit

oﬀ , and remove the battery from the main body.

Always monitor the workplace and surrounding area,

ensure there are no objects which could cause injuries,

accidents or failure, and if any are present, remove them

in advance.

In particular, when establishing a foothold for working,

ensure there is no instability or any object which could be

tripped over.

Ensuring the unit is switched oﬀ

If the storage battery is inserted while the switch is

unknowingly engaged, the unit may unexpectedly

start, which may result in an accident.

Installing the battery (Fig. 5)

As shown in Fig. 5, push ﬁ rmly until it clicks into place.

Engaging the switch

Ensuring the saw chain is not in contact with the timber,

engage the switch, and start cutting when the saw

chain speed has increased.

CAUTION

○ When switching the unit on, ensure the saw chain does

not contact with material or anything else.

○ During use, be careful to ensure the saw chain does

not contact with other material or object. In particular,

when you have ﬁ nished cutting, be careful to ensure it

does not touch the ground.

16

English

NOTE

Reﬁ ll the oil tank early to prevent the unit running out of

oil.

1. General cutting procedures

(1) Switch ON the power while keeping the saw slightly

away from the wood to be cut. Start sawing only after

the unit has reached full speed.

(2) When sawing a slender piece of wood, press the base

section of the guide bar against the wood and saw

downward as shown in Fig. 21.

(3) When sawing a thick piece of wood, press the spike

(sold separately) on the front section of the unit against

the wood and cut it with a lever action while using the

spike as a fulcrum as shown in Fig. 22.

(4) When cutting wood horizontally, turn the unit body to

the right so that the guide bar is below and hold the

upper side of the front handle with your left hand. Hold

the guide bar horizontally and place the spike (sold

separately) that is on the front of the unit body on the

lumbar. Using the spike as a fulcrum, cut into the wood

by turning the rear handle to the right. (Fig. 23)

(5) When cutting into wood from the bottom, touch the

upper part of the guide bar to the wood lightly. (Fig. 24)

(6) As well as carefully studying the handling instructions,

ensure practical instruction in the operation of the

chain saw prior to use, or at least practice working with

the chain saw by cutting lengths of round timber on a

sawing trestle.

(7) When cutting logs or timbers which are not supported,

support them properly by immobilizing them during

cutting using a sawing trestle or other proper method.

CAUTION

○ When cutting wood from the bottom, there is a danger

that the unit body may be pushed back toward the user

if the chain strongly impacts with the wood.

○ Do not cut all the way thorough the wood by starting

from the bottom since there is the danger of the guide

bar ﬂ ying up out of control when the cut is ﬁ nished.

○ Always prevent the operating chain saw from touching

the ground or wire fences.

2. Branch cutting

(1) Cutting branches from a standing tree:

A thick branch should initially be cut oﬀ at a point away

from the trunk of the tree.

First cut in about one third of the way from below, and

then cut oﬀ the branch from above. Finally, cut oﬀ the

remaining portion of the branch even with the trunk of

the tree. (Fig. 25)

CAUTION

○ Always be careful to avoid falling branches.

○ Always be alert for chain saw recoil.

(2) Cutting branches from fallen trees:

First cut oﬀ branches that do not touch the ground, then

cut oﬀ those which touch the ground. When cutting

thick branches that touch the ground, ﬁ rst cut in about

half of the way from above, then cut the branch oﬀ from

below. (Fig. 26)

CAUTION

○ When cutting oﬀ branches which touch the ground, be

careful that the guide bar does not become bound by

pressure.

○ During the ﬁ nal cutting stage, beware of the log

suddenly rolling.

3. Log cutting

When cutting a log positioned as shown in Fig. 27, ﬁ rst

cut in about one third of the way from below, then cut

down all the way from above. When cutting a log that

straddles a hollow as shown in Fig. 28, ﬁ rst cut in about

two thirds of the way from above, then cut upward from

below.

CAUTION

○ Ensure the guide bar does not become bound in the log

by pressure.

○ When working on inclined ground, be sure to stand on

the uphill side of the log. If you stand on the downhill

side, the cut-oﬀ log may roll toward you.

4. Cutting a log laid ﬂ at

Make sure the log is stable.

Push the spike against the log. Use the spike as a

fulcrum about which the handle can be lifted to facilitate

cutting. (Fig. 29)

5. Cutting a log supported at both ends

Start by sawing to a depth of approximately one third

from the top, then saw from underneath to complete the

cut.

The guide bar may become stuck within the saw cut

if you attempt to cut all the way through from the top.

(Fig. 30)

Precaution for cutting work

For large-scale operation or non-stop work

This tool comes with an over-heat protection circuit

that protects the electronic parts that control the

rechargeable battery. During sustained use or

during operations under high loads generated by

pressure against the tool, tool temperature will rise

and eventually trigger the over-heat protection circuit,

which will shut down the tool.

If this happens, let the tool cool for a length of time.

When the temperature drops, it will again become

possible to use the tool. When the rechargeable battery

has to be exchanged during continuous operation, let

the tool rest for about 15 minutes.

Gripping/pushing force of chain saw

Always grip the chain saw securely.

In addition, do not force the chain saw more than

necessary. When cutting, additional force exerted on

the chain saw will not accelerate the cutting speed.

This will strain the motor, impair the performance, and

damage or cause malfunction of the motor or guide bar.

Use the unit in the range where the saw chain is at a

reasonable speed.

In particular, when the saw chain stops (becomes

jammed) due to the excessive force, it may cause an

injury or failure of the unit.

Chain catcher

○ The chain catcher is located on the power head just

below the chain to further prevent the possibility of a

broken chain striking the chain saw user.

○ When the saw chain is cut, replace it with a new one

referring to “Installing (replacing) saw chain”.

SHARPENING OF THE CHAIN BLADE

WARNING

To prevent accidents, always turn oﬀ the switch and

remove the battery from the main body.

CAUTION

Always wear thick gloves when handling the saw chain.

NOTE

Sharpen the saw chain and adjust the depth gauge at

the central position on the guide bar, with the saw chain

attached to the main body.

17

English

When the sharpness of saw chains deteriorates, the motor

and each part of the body are burdened and the eﬃ ciency

declines.

For optimal performance of the unit, frequent maintenance

is necessary to keep the saw chain sharp.

1. Blade sharpening

Use a 4 mm diameter round ﬁ le.

The round ﬁ le should be held against the chain blade

so that one-ﬁ fth of its diameter extends above the top

of the blade, as shown in Fig. 31.

Sharpen the blades by keeping the round ﬁ le at a 30°

angle in relation to the guide bar, as shown in Fig. 32.

File the blades by gently pushing the round ﬁ le in the

direction of the grip.

Make sure the round ﬁ le does not touch the saw chain

when drawing back the ﬁ le.

Ensure that all saw blades are ﬁ led at the same angle,

or the cutting eﬃ ciency of the tool will be impaired.

Appropriate angles for sharpening the blades correctly

are shown in Fig. 33. (Round ﬁ le is sold separately.)

2. Adjustment of depth gauge

WARNING

○ Do not sand the top part of the bumper tie strap and

bumper drive link, nor cause the shape of said parts to

deform.

○ Adjustment of depth gauges must be in line with the

predetermined dimensions and shapes, otherwise the

risk of kickback may increase, causing an injury.

Bumper tie strap Bumper drive link

Depth gauges shall be all lined up in the same manner

because they are used to adjust depth at the position

where the cutter inlays into the wood.

When sharpening the saw chain, be sure to check the

depth gauge every two or three times. (Fig. 34)

Place a depth gauge jointer on the saw chain, leave the

gauge visible at the groove, and use a ﬂ at ﬁ le to bevel

the portion out of the depth gauge jointer. (Fig. 35)

(Depth gauge jointer and ﬂ at ﬁ le are sold separately.)

After ﬁ ling away the depth gauge, round oﬀ the front

side of the depth gauge as it was. (Fig. 36)

After sharpening the saw chain, place it into chain oil to

wash oﬀ the ﬁ lings.

If ﬁ lings are not cleaned oﬀ , the saw chain and guide

bar will quickly wear while in use.

The depth gauge jointer can also be used when

dressing with a round ﬁ le. (Fig. 37)

MAINTENANCE AND INSPECTION

After operation, perform inspection and maintenance of

each part when storing the unit.

WARNING

During maintenance and inspection, always switch oﬀ

the unit and remove the battery from the main body.

CAUTION

Always wear thick gloves when handling the saw chain.

1. Inspection of saw chains

○ Occasionally inspect the saw chain. In the event of

any abnormality, replace it with a new one referring to

“Installing (replacing) saw chain” .

○ Inspect the chain tension and check If it is correctly

tightened.

○ Stop using the unit when the saw chain becomes blunt

and sharpen it referring to “Sharpening of the chain

blade”.

○ After use, carefully lubricate the saw chain and guide

bars with oil for rust-prooﬁ ng.

NOTE

When cleaning the side cover, sprocket, chain oil

spout, and guide bar, see the procedure “Installing

(replacing) saw chain” and remove the saw chain.

2. Cleaning the side cover and sprocket (Fig. 38)

Clean and remove any swarf or dust left inside the

parts.

3. Cleaning the chain oil spout (Fig. 39)

Before cleaning the chain oil spout, remove the side

cover and guide bar.

4. Cleaning the guide bar (Fig. 40)

When sawdust and similar become clogged in the

groove of the guide bar or oil spout, the oil may not ﬂ ow,

which may result in the unit failing.

Remove the guide bar and clean any sawdust clogged

in the groove after use and when replacing the saw

chain. (Refer to “Installing (replacing) saw chain.”)

5. Cleaning the chain brake (Fig. 41)

Use a brush to remove any swarf from the gap to the

saw body.

6. Inspecting the chain catcher (Fig. 42)

The chain catcher is designed to protect the operator

from being struck by the saw chain if the chain comes

loose or is severed.

The chain catcher is integrated into the side cover.

Check to conﬁ rm that the chain catcher is not damaged.

7. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws

be loose, retighten them immediately. Failure to do so

could result in serious hazard.

8. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

9. Cleaning the battery installation compartment

and the battery (Fig. 43)

WARNING

Wear protective glasses and a dust mask when

cleaning with an air blow gun.

Failure to do so may result in inhalation or exposure of

the eyes to debris or dust.

Use a brush or air blow gun to remove any swarf or dust

and keep the saw clean.

NOTE

○ Allowing swarf and dust to build up during use may

cause the battery to fall oﬀ or other accidents.

Allowing swarf and dust to build up can also result in

malfunctions, including faulty contact between the

battery and the terminals.

○ After cleaning, check to conﬁ rm that the battery can be

easily detached and reattached to the tool body.

10. Cleaning of the outside

When the chain saw is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not use

chloric solvents, gasoline or paint thinner, for they melt

plastics.

11. Storage

○ Clean all parts thoroughly. Coat metal parts with a thin

layer of corrosion inhibitor.

○ Be sure to repair any damaged areas before storing.

○ When storing the unit, perform cleaning and

maintenance of each part and mount the chain case to

the guide bar.

○ Store the power tool and battery in a place in which

the temperature is less than 40°C and out of reach of

children.

18

English

NOTE

Storing Lithium-ion Batteries

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries

dead and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used

with batteries other than these designated by us, or

when the battery is disassembled and modiﬁ ed (such

as disassembly and replacement of cells or other

internal parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

Information concerning airborne noise and vibration

The measured values were determined according to

EN62841 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 98 dB (A)

Measured A-weighted sound pressure level: 88 dB (A)

Uncertainty K: 3 dB (A)

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN62841.

ah = 2.5 m/s2

Uncertainty K = 1.5 m/s2

The declared vibration total value and the declared noise

emission value have been measured in accordance with a

standard test method and may be used for comparing one

tool with another.

They may also be used in a preliminary assessment of

exposure.

WARNING

○ The vibration and noise emission during actual use

of the power tool can diﬀ er from the declared total

value depending on the ways in which the tool is used

especially what kind of workpiece is processed; and

○ Identify safety measures to protect the operator that

are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched oﬀ and when it is running idle in addition to

the trigger time).

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

19

English

TROUBLESHOOTING

Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult

your dealer or the HiKOKI Authorized Service Center.

Symptom Possible cause Remedy

The motor sounds but the

saw chain...

○ does not move

○ does not move freely

The chain brake may be activated. Release by pulling the chain brake toward

you.

The saw chain tension is excessive. Check the saw chain tension, and if it is

too tight, loosen the tension.

Saw chain comes out of the sprocket. Check the saw chain is properly engaged

on the sprocket.

Inside the side cover...

→ sawdust is jammed

→ foreign matter is trapped

Clean the side cover.

In the guide bar groove...

→ sawdust is jammed

→ oil does not ﬂ ow

Clean the guide bar groove and the oil

hole.

Make sure there is oil in the oil tank, and

replenish as required.

Poor sharpness The saw chain...

→ is worn out or the blade is broken

→ is rusted

Sharpen the saw chain.

If the wear or breakage is very severe,

replace with a new saw chain.

The direction of the saw chain is reversed, Re-attach ensuring the correct direction.

Saw chain tension is loose. Check the saw chain tension and tighten

if it is loose.

Chain oil

○ is slow-ﬂ owing

○ does not come out

(seizes up)

Lack of chain oil in the tank. Replenish with chain oil.

Chain oil spout is clogged. Clean the chain oil spout.

20

Deutsch (Übersetzung der Original-Gebrauchsanweisung)

SYMBOLE

WARNUNG

Die folgenden Symbole werden für diese

Maschine verwendet. Achten Sie darauf, diese vor

der Verwendung zu verstehen.

CS1825DC: Akku-Kettensäge

Der Anwender muss die Bedienungsanleitung

lesen, um das Risiko einer Verletzung zu

verringern.

Verwenden Sie die Heckenschere nicht im

Regen oder bei Feuchtigkeit, und belassen sie

das Gerät bei Regen nicht im Freien.

Nur für EU-Länder

Werfen Sie Elektrowerkzeuge nicht in den

Hausmüll!

Gemäss Europäischer Richtlinie 2012/19/EU

über Elektro- und Elektronik- Altgeräte und

Umsetzung in nationales Recht müssen

verbrauchte Elektrowerkzeuge getrennt

gesammelt und einer umweltgerechaten

Wiederververtung zugeführt werden.

Lesen, verstehen und befolgen Sie alle

Warnungen und Anweisungen in dieser

Anleitung und am Gerät selbst.

Bei Gebrauch des Geräts immer Gesichts-,

Kopf- und Gehörschutz tragen.

Achten Sie auf einen möglichen Rückschlag

der Kettensäge und vermeiden Sie den

Kontakt mit der Schwertspitze.

Führen Sie die Kettensäge immer mit beiden

Händen.

Es ist wichtig, dass Sie Schutzbekleidung für

Füße, Beine, Hände, Unterarme und den Kopf

tragen.

Diese Kettensäge darf nur von geschulten

Forstarbeitern benutzt werden. Die

Verwendung ohne entsprechende Schulung

kann zu schweren Verletzungen führen.

Einstellung der Ölversorgung der Kette

Trennen Sie die Batterie ab

TEILEBEZEICHNUNGEN (Abb.1)

A Batterie (separat zu beziehen): Energiequelle für den

Antrieb des Gerätes.

B: Schalter: Das Gerät wird mit dem Finger aktiviert.

C: Entriegelungshebel: Dieser Hebel verhindert ein

unbeabsichtigtes Betätigen des Auslösers.

D: Kettenbremse: Vorrichtung zum Stoppen bzw.

Verriegeln der Sägekette.

E: Seitliche Abdeckung: Schutzabdeckung für Schwert

und Sägekette, Vorgelege und Kettenzahnrad, wenn

die Kettensäge in Benutzung ist.

F: Mutter: Mutter zur Befestigung der Seitenabdeckung.

G: Spannschraube: Vorrichtung zum Einstellen der

Spannung der Sägekette.

H: Vorderer Griﬀ : Haltegriﬀ an der Vorderseite des

Gerätkörpers.

I: Hinterer Griﬀ (Oberer Griﬀ ): Stützgriﬀ an der Rückseite

des Hauptgehäuses.

J: Sägekette: Kette, die als Schneidewerk- zeug dient.

K: Schwert: Der Teil, der die Sägekette trägt und führt.

L: Öltankdeckel: Deckel zum Verschließen des Öltanks.

M: Öl-Sichtglas: Fenster zum Prüfen des Kettenölpegels.

N: Haken: Werkzeug, um das Gerät mit einem Seil usw.

aufzuhängen.

O Öleinspeisung: Ölbehälter.

P: Kettengehäuse: Gehäuse zum Abdecken von Schwert

und Sägekette, wenn das Gerät nicht in Gebrauch ist.

Q: Kombisteckschlüssel: Das Werkzeug zum Entfernen

oder Anbringen einer Seitenabdeckung und zum

Spannen der Sägekette.

WARNUNG

Diese Motorsäge (CS1825DC) ist speziell für

Baump-ﬂ ege und Baumchirurgie vorgesehen.

Alle Arbeiten mit dieser Motorsäge dürfen nur von

ausgebildeten Baumpﬂ egekräften durchgeführt

werden. Einschlägige Liter-atur und Hinweise

der Berufsgenos-senschaft befolgen. Bei

Nichtbeachtung besteht hohe Unfallgefahr. Zur

Arbeit mit der Motorsäge in Bäumen empfehlen

wir stets eine Arbeitsbühne einzusetzen. Die

Arbeit mit der Abseiltechnik ist extrem gefährlich

und nur nach einer speziellen Ausbildung

durchzuführen. Der Bediener muß im Umgang mit

Sicherheitsausrüstungen und mit den Ar-beitsund

Klettertechniken geschult sein! Bei Arbeiten in

Bäumen müässen Gurte, Seile sowie Karabinerhaken

eingesetzt werden. Rückhaltesysteme für Motorsäge

und Bediener anwenden.

ALLGEMEINE

SICHERHEITSHINWEISE FÜR

ELEKTROGERÄTE

WARNUNG

Bitte beachten Sie sämtliche mit diesem Elektrogerät

gelieferten Sicherheitshinweise, Anweisungen,

Illustrationen und technischen Angaben.

Wenn die nachfolgenden Anweisungen nicht befolgt

werden, kann es zu Stromschlag, Brand und/oder

ernsthaften Verletzungen kommen.

Bitte bewahren Sie alle Warnhinweise und

Anweisungen zum späteren Nachschlagen auf.

Der Begriﬀ „Elektrowerkzeug“ bezieht sich in den

Warnhinweisen auf Elektrowerkzeuge mit Netz-

(schnurgebunden) oder Akkubetrieb (schnurlos).

La pagina sta caricando ...

Hikoki CS1825DC Manuale utente

Hikoki CS1825DC Manuale utente

in altre lingue

Documenti correlati

Altri documenti