1
Cyclone RGB II
User Manual
2
Note: To ensure reasonable consistency of operation, please read this
manual carefully. Any damages caused by the non-observance of this
manual or any unauthorized modification to this product are not subject
to warranty.
1. Maintain a 50CM space at the back of the fixture for dissipate heat.
2. This lamp is used for indoor lighting. When lamp works, lamp tube at
high temperature.
3. Make sure the voltage and frequency of power supply match the power
require of this devise.
4. Please do not operate the equipment in the condition of wire damage or
wear.
5. Do not remove any part of the equipment during the use of the fixture.
6. Any unauthorized modification to this product is not subject to
warranty.
Safety Notes
3
1. Display panel and key button definition
Menu key: Select the function
Up key: parameter
arguments Down key:
parameter decline
Confirm key: Determine
and save
2. Menu function
Press the menu; key up or down to modify the function parameters and
confirm with enter, which saves the current function and parameters (power
memory after saving).
Menu function table：
A00
1
A512 Modify the address code up or down (A001~A 512) to confirm that the key is
saved, with the default of A001.
CH0
3
CH24
Switch CH03, CH09, CH24 three channels up or down, confirm the key save,
default CH09.
FF0
0
FF99 Gradient, up or down to modify the gradient speed (FF00~ FF99), confirm that
the key is saved, the default FF10.
EE0
0
EE99 Pulse change, up or down to modify the pulse change speed (EE00~ EE99),
confirm the key to save, the default EE10.
P00
0
P241
There are 242 built-in effects (P000~P241), switch the built-in effects up or
down, confirm the key save, and the default P000 jump.
S00
0
S255 Modify the built-in effect running speed (S 000-S 255) and confirm that the key is
saved, with the default S010.
Sou
d
Soud Sound control mode.
R25
5
R000
Modify the red bead brightness (R 000-R255) up or down, and confirm that the
key is saved, with the default R 255.
G25
5
G000
Modify the green bead brightness (G000~ G255) to confirm that the key is
saved, with the default G255.
B25
5
B000 Modify the blue bead brightness up or down (B000~ B255), and confirm that the
key is saved, with the default B255.
T00
0
Display temperature, such as T045 indicates the current lamp temperature of
45℃; 10K thermistor is not installed, display T000.
4
3. Master-slave control
Two or more of the same fixtures are connected by DMX three-core signal
line, the fixture is set to any address code of A001~A512, any one is set as
the master, and the other fixture are the slaves.
Pay attention: Only one host can be set for a group of fixtures. If there are more
than one host, all fixtures will flash randomly and out of sync.
4. Factory setting
When any address code is A001~A512, press the menu button for 3 seconds
to enter the factory setting. The factory settings are mainly the functions of the
output power of each lamp, the fan setting mode, setting the temperature
protection point, and sending the parameters. Any mode set by the factory,
press the menu button for 3 seconds to exit.
Factory setting List:
R
255
R032
Modify
the red current (R032-R 255) up or down to confirm that the key is saved
with
the default R240.
G
255
G032
Modify
the green current up or down (G 032-G255) to confirm that the key
is
saved, with the default G240.
B
255
B032
Modify
the blue current up or down (B 032-B255), and confirm that the key
is
saved with the default B240.
FAN0
FAN1
Fan
setting: FAN0 lights on to start the fan, FAN1 reaches the set
temperature
protection points to start the fan, and confirm the key to save.
T040
T105
Set
the temperature protection point, modify the parameters up or down (40℃ ~105℃
)
and press OK to save, with the default T060.
S
end
S
end
Send
the parameters set by the local factory up or down to all other fixture connected
by three
-core signal lines; confirm that the transmission parameters exit by the
dish
menu key for 3 seconds and cancel the transmission by the confirmation key.
5
5. DMX512 console
After power on, all fixture address codes are set, all fixtures are
connected to the DMX512 console in parallel with a three-core signal line, and
the address code will stop flashing, indicating that the DMX512 console signal
has been sent to the lamp, and the relevant functions are controlled by the
DMX512 console according to each channel description.
CH03-channel Description:
chan
nel
Channel
value
basic function
1
000-255
Red dimming
2
000-255
Green dimming
3
000-255
Blue dimming
CH09 channel description:
chan
nel
Channel
value
basic function
1
000-255
Total dimming
2
000-255
Red dimming
3
000-255
Green dimming
4
000-255
Blue lamp beads for linear dimming
5
000-255
Strobe
6
000-255
Chase Mode 1 (Different chases every 2 DMX values)
7
000-255
Chase Mode 2 (Different chases every 2 DMX values)
8
000-255
Chase Mode 3 (Different chases every 2 DMX values)
9
000-255
Chase Speed
Description of the Ch24 channel:
cha
nnel
Channel
value
basic function
1
000-255
Red Section 1
2
000-255
Green Section 1
3
000-255
Blue Section 1
…
…
……
22
000-255
Red Section 8
23
000-255
Green Section 8
24
000-255
Blue Section 8
6
6. Technical parameters:
Voltage: AC100~240V 50 / 60HZ Power:
240W
LED: x960,0503-RGBcolor LED
Control mode: DMX512, Auto, master, sound control.
Channel: CH03, CH09, and CH24
8 independent LED control sections.
Strobe frequency: 1~30HZ
Housing: Metal, black
Connection mode: DMX512 input / output
IP level: IP20
-
1
-
2
-
3
-
4
-
5
-
6
in altre lingue
- English: FOS Cyclone RGB II User manual
Altri documenti
-
DTS X-BRICK Manuale utente
-
DTS EUPHONY 3 Manuale utente
-
ProLights STARK400 Manuale utente
-
-
-
-
CHAUVET DJ Mini Kinta Guida di riferimento
-
