Comelit 100 Series Manuale utente

CAMERAS IP 100 SERIES

Please read this manual thoroughly before use and keep it for future reference

Statement

The instruction is for guidance only. Detailed information is in accordance with the product.

The instruction may include some technical inaccuracies or typographical error thought it is prepared with

our every effort.

The product or procedures described in the instruction may be changed or updated at any time without

advance notice.

Screenshots used in the instruction are only for indications and explanations.

For any doubts or to request documents about latest procedures and complementary notes, please

consult with the after-sales service department..

Precautions

The followings describe information about correct usage and risk prevention as well property loss

prevention to be strictly followed.

Please use web cameras in an environment within allowable temperature and humidity.

Check if the power supply works normally before operation.

Do not furiously strike on the product and be careful not to fall it over.

Do not install the product in a dusty or moist place, or a place with strong electromagnetic radiation.

Do not place a container or others with liquid on the product or allow liquid flowing into inside the product.

When the product is left unused, place install the preventive dust cover for the image sensor.

Do not disassemble the product without authorization.

1

A. Art. IPCAM1838A, IPCAM1848A, IPCAM184KA installation

Mounting the camera

1.Take out the camera and installation accessories from inside the box, install the template sticker in

order to make the holes properly. Open the camera and fix it using the plugs (Figure 1).

2.Tear off the lens protective film and adjust the camera angle (Figure 2 and 3).

3.Follow the instruction lens adjustment and desiccant placement instruction, close the camera and lock

the screws to complete the installation (Figure 4).

75° 75°

Figure 1 Figure 2

75°

Figure 3 Figure 4

Lens adjustment

1.Rotate the 3D stand, which can rotate in the horizontal direction, the rotation angle is around 75° each

side

2.Loose the screw 1, which can be adjusted in the vertical direction, the adjustable range is 0~75°

3.Loose the screw 2, rotation adjustament, restricted by the internal connector, we suggest no more

than 30° rotation angle

75° 75° Screw 1

3D stand 75°

0°

Horizontal adjustment Vertical adjustment Rotation adjustment

For vertical wall installation use the "Mirror" function, in "Video parameters" of the camera, to have a

straight image.

Desiccant placement instructions:

After installing the camera to adjust the direction of monitoring, remove the desiccant from the box and

insert it as showed in the picture (desiccant placement)

Due to different temperature between inside and outside the housing, may there be moisture inside the

camera when switch on for the first time. Please power off the camera until the desiccant absorbs the

moisture and than switch on again.

The desiccant may not be effective if the camera has been left opened during installation more than 1

hour, in this case please replace the desiccant.

Screw 2

Ceiling or wall

Install the stickers

0°

2

B. Art. IPCAM133A installation

Mounting the camera

1. Take out the camera from the box and rotate the upper cover to open it (as shown in figure 1).

2. Paste the mounting sticker to the wall, align the hole position of camera lower cover with the

corresponding position of installation sticker hole, and fix the camera lower cover to the wall using the

accessories (as shown in figure 2).

3. Adjust position of the housing body to ensure that the camera reaches the requirements of users,

adjust the angle (lens adjustment, explained below) and remove the lens protection film (as shown in

figure 3).

4. After adjusting the lens, close the upper cover to complete the installation (as shown in figure 4).

Figure 1 Figure 2

Figure 3 Figure 4

Lens adjustment

After fixing the camera, you can adjust the angle by using the three-axis mounting bracket, horizontal,

vertical and rotation.

320° 60° for left and 50° for right 360°

Horizontal adjustment for bracket Vertical adjustment for dome body Camera rotation

Desiccant placement

Mounting

stickers

Lens protective

film

Bracket rotation

60°

50°

Dome

body

Bracket

screw

Fixing ring

screw

3

Note: When the dome body vertical adjusting is set to 60° to the left, the camera rotation limit is 20° both

clockwise and counterclockwise.

Follow the mounting instruction when regulate, don’t overtake the regulation limits. If the IR Led are

covered, they will reflect the light on the image as showed in the picture.

Be careful with the bubble. Remove the protective film just when the installation is complete. If need to

clean it, use an anti-scratch cloth. If the bubble is scratched, the leds will reflect the light and may cause

issue in night condition.

C. Art. IPCAM183B and IPCAM185B installation

Mounting the camera

1. Take out the camera from the box, use the hexagon wrench to loose the screws (as shown in figure 1),

remove the mounting plate, paste mounting sticker to the wall, and use mounting accessories to fix it to

the wall (as shown in figure 1).

2. Mount the camera lower cover by rotating it (as shown in figure 2), than lock the little screw on the side

of the camera (as shown in figure 3).

3. Adjust camera angle (lens adjustment) according to user's requirements. Than remove the protection

film (as shown in figure 4).

4. After adjusting the lens, remove the protective film, close the upper cover and lock the screw.

Figure 1 Figure 2

Figure 3 Figure 4

Lens adjustment

After fixing the camera, you can adjust the angle by using the three-axis mounting bracket, horizontal,

vertical and rotation.

360° 50° for left and 80° for right 360°

Horizontal adjustment for bracket Vertical adjustment for dome body Camera rotation

Bracket

(rotatable)

50°

80°

Dome

body

Bracket screw

Mounting

plate

Mounting

stickers

Hexagon

wrench

Lens protective

film

Fixing ring

screw

4

Note: when the dome body vertical adjusting is set 80° to the right, the rotation regulation limit is 30° both

clockwise and counterclockwise.

Follow the mounting instruction when regulate, don’t overtake the regulation limits. If the IR Led are

covered, they will reflect the light on the image as showed in the picture.

Be careful with the bubble. Remove the protective film just when the installation is complete. If need to

clean it, use an anti-scratch cloth. If the bubble is scratched, the leds will reflect the light and may cause

issue in night condition.

Login Interface

Input the IP address of the front-end device into the IE browser (default IP address is

192.168.1.188) to access the Login interface, as shown in the following figure:

After entering into the login interface, it will prompt to install the Activex control, as shown in the

follow figure:

User Name: admin (default setting)

Password: blank (default setting)

5

Model: IE ActiveX or Non ActiveX. If you use IE browser, then please select IE ActiveX to login.

While you use other browsers, then select Non ActiveX to login.

Note: Select Non ActiveX without installing Activex control

Select Language: select the desired language

Click Submit to login.

Live view

After login, it will enter into the live preview, as shown in the follow figure.

Note: the inserted micro-SD card is for full function display interface, otherwise, it's for simple type

interface.

Full-screen Preview

Click the full-screen icon in the lower right corner to preview full screen, or you can click

right mouse button to enter and exit the full screen display in the preview interface.

Electronic Zoom-in

It can zoom in the preview image by scrolling the mouse wheel, as shown in the follow figure:

6

PTZ Control

PTZ Control: You can use eight directional keys to rotate front-end devices, and AUTO indicates

auto-rotation.

Zoom +/ - : To adjust degree of zoom in/ out

Focus: To adjust size of focus

Iris: To adjust size of aperture

Speed: Use the slider to regulate the PTZ speed

Bright: To adjust the brightness of the screen

Contrast: To adjust the contrast of the screen

The arrow is used to restore default settings.

Set a Preset point: Set a preset point by using directional keys on the PTZ control to rotate the camera

to the desired location, next select a preset number from the Preset Point drop-down list, and then press

button.

Call a Preset point: Call a preset point by selecting a preset number to be called from the Preset Point

drop-down list and press button.

7

Voice Intercom: Click it to enable or disable voice intercom

Capture: Capture for preview. Click the capture icon, it will pop up its storage path automatically.

Full Screen: Display the current preview in full screen

Record: Enable or disable preview interface record

Event Type: Enable or disable disarming/ clear alarm

Note: X indicates the function is off or disabled

Playback

Click Playback enter into playback interface, click the icon , next select the date time of the

calling video in need, then click the icon , the record video will search

automatically, as shown in the follow figure:

Start: Start the current playback

Stop: Stop the current playback

Slow: Slow down the playback speed (1/2, 1/4, 1/8, 1/16 times optional)

Fast: Speed up the playback speed (2, 4, 8, 16 times optional)

Capture: Can be capture in playback channel

Backup: Can be backup video in playback channel

Frame Play: Single frame to play

VOICE INTERCOM

Capture

Full Screen

Record

Event Type

8

Full Screen: Playback video will display with full screen

Show smart detection: when the video is to intelligent detect video, it can display intelligent

Detection rules and statistical result.

Voice: Adjust the volume of playback audio

Double-click the slider location, it will start to play the video, or you can click the Start button to

playback video.

Note: The device should support micro-SD card storage to enable this function

Setup

Note: the inserted micro-SD card is for full function display interface, otherwise, it's for simple type

interface.

Device Info

IP Camera Device Info interface as shown in the follow figure:

9

 Device Name: Edit the camera name

 Device Type: Display the device type

 Serial No. : Display the product serial No.

 Master Version: Display the software version date (Note: Based on the version information which

displayed in factory product)

 Hardware Version: Display the hardware version number

 Audio Source: Select the audio input mode, LineIn or MicIn selectable

 Input Volume: Set the size of the input volume, the range of volume:0-100, default is 50

 Output Volume: Set the size of the output volume, the range of volume:0-100, default is 50

 Format: Switch to select the PAL and NTSC image scanning system

 Device Time: Set and display the device current time

After complete all parameters setting, click Save and then it will take effect immediately.

QR Code

The display interface of QR code of IP Camera is shown as below. Use Comelit View 100 app to

directly scan the Comelit View 100 ID QR code to login.

Note: the Device ID QR icon will display only after the opening the corresponding agreement in

platform management interface and it supports Comelit View 100 QR code at present:. Comelit View 100

is corresponding to Comelit View 100 client in platform management interface.

10

Encoding

IP Camera Encoding setting interface as shown in the follow figure:

 Compress Type: Primary Stream(Normal)/ Sub Stream selectable

 Stream: Include complex stream/ video stream two types

 Resolution: The camera supports several resolution , will display here (Note: based on the default

resolution of factory products)

 Frame Rate: Select different frame rate in the drop-down list, default is Full Frame

 Video Encode: H.264/ MJPEG/H.264+ three kinds of video encode format

 H264 Profile: There are MainProfile/ Baseline/ HighProfile three types optional

 I frame Interval: Set the I frame interval size

 Bitrate Type: Constant/ Variable selectable

 Bitrate: Set different bitrate for different channels

After complete all parameters setting, click Save and then it will take effect immediately.

11

Video Parameters

IP Camera Video Parameters setting interface as shown in the follow figure:

 Day&Night Mode: Outside Trigger/ Auto/ Color/ Black White four kinds of mode selectable. Non

infrared IP cameras default mode is Auto, and infrared IP cameras default mode is Outside Trigger.

According to the IP camera type and actual scene, user can select the Day&Night mode optional

 Switching Time: Day&Night switch delay time, 0-30s selectable, and default is 3s

 Day-Ni-Threshold: 0-255 selectable, users can adjust it according to the need, default is 20

 Ni-Day-Threshold: 0-255 selectable, users can adjust it according to the need, default is 35

 Color Mode: Normal/ Bright/ Nature three options, default is Normal

 Mirror: Close/ Horizonal Mirror/ Vertical Mirror/ 180 Rotation/90 Rotation/270 Rotation six options,

default is Close

 TWDR/WDR: Close/ Low/ Mid/ High four options, default is Close

 3DNR: Close/ Low/ Mid/ Mid-High/ High five levels, default is Low

 Sharpness: 0-255 selectable, default is 128

 Defogging: Close/ Low/ Mid/ High four options, default is Close.

 Slow Shutter: Close/Open selectable, default is Close.

 Exposure Control Mode: Auto/ Manual selectable, default is Auto

 AGC: It can be set when it's automatic exposure, Low/ Mid-Low/ Mid/ Mid-High/ High selectable,

default is Mid-High. The higher Auto Gain value, the better sensitivity within low illumination, while the

noise will be more obvious

 Shutter: It can be set when it's manual exposure, the shutter value range:1/30（25）-1/10000

 Aperture:According to the IPC lens type, the aperture can be divided into manual aperture and

auto aperture (Note: based on the default aperture of factory products), the lens can be divided into

manual focus and semiautomatic focus (Note: there is this option when it's equipped with electric lens)

 Gamma: CURVE_1_6, CURVE_1_8, CURVE_2_0, CURVE_2_2 totally four modes, default is

CURVE_2_0

 Anti-Fliker: Close, 50hz, 60hz three types, the default is Close

 Light board control: 3 types of led board control mode: close, manual, auto. Default to auto. (Note:

12

there is this option when it's equipped with Smart IR)

Closing mode: The led board can not be control, and it always close.

Manual mode: The led board brightness can be adjusted by manually change the parameters, and

the range is 1-100, the higher the parameter value, the brighter the IR led.

Auto mode: The image of the camera can be optimum, and it's power can be the minimum by

acquiring the current image brightness & exposure & gain, and dynamically adjusting the light

brightness.

 Bright: The led board brightness can be set when the led board control is under manual mode, and

the range is 1-100.

After complete all parameters setting, click Save, the settings will take effect immediately.

Network Settings

IP Camera Network Settings interface as shown in the follow figure:

 IPV4: IP protocol version No. is 4

 IPV6: IP protocol version No. is 6, the feature is not optional at present

 Static IP: The device IP address is permanent

 DHCP: Enable DHCP, then IP camera will get the IP address from router automatically

 IP Address: Input the corresponding numbers to change the IP address

 Subnet Mask: Input the corresponding IP subnet mask

 Gateway: Input the corresponding gateway address

 DNS 1: DNS server IP address

 DNS2: DNS server second IP address

 HTTP Port: Input the corresponding port ( Default is 80)

 HTTPS Port: Input the corresponding port ( Default is 443)

 RTSP Port: Use domain name to access and login device need mapping RTSP, default port is 554

 RTMP Port: Use domain name to access and login device need mapping RTMP, default port is

1935

 Enable UPnP: Enable UPnP, then device port and HTTP port will be mapped to the router

automatically

 Device Port: Input the corresponding device port(Default is 5050)

13

 Enable PPPoe: Click to enable PPPOE

User Name: Input the user name

Password: Input the password

Confirm pwd: Input the password again to confirm it

PPPoe IP: Input device dynamic address

After complete all parameters setting, click Save, then the settings will take effect immediately.

DDNS Setting

DDNS is implemented through a dynamic domain resolution server. It requires a PC running in the

server with fixed IP address on the Internet. IP Camera DDNS setting interface as below figure:

 Enable DDNS: Click to determine whether to use Dynamic Domain Name Server

 Server Type: Select DDNS server type

 Server Name: Input server name

 Port: Input port No.（default is 80）

 Username: Input user name

 Password: Input password (max 10 char.)

 Confirm pwd: Input the password again to confirm it

 Domain: Input the domain

After complete all parameters setting, click Save, then the settings will take effect immediately.

User Info

IP Camera User Info setting interface as below figure, admin is the administrator (default), Default

indicates general users.

14

 Modify: Administrator account can modify login password, while general users can modify user

type including Guest, Operator two options, and setup different permission assignment in the Rights

Permission settings

 Del: Delete the new user

 Rights Permission: Set rights permission assignment for new user

 Add User: Add a new user in need

Start up and login permission is accord with default user permission (default), as shown in the

follow figure:

After complete all parameters setting, click Save and then the settings will take effect immediately.

System Update

IP Camera System Update setting interface as shown in the follow figure:

15

 File: Click Browse to find and select the upgrade kit, then click Update.

 NOTE: to upgrade must first be uploaded the file whose name starts with (Main fw), then the one whose

name starts (Sub fw). After the upgrade is mandatory to restore the camera to the factory configuration

(default). Before reconnecting the camera, clear the IE cache memory and the old ActiveX.

Non-technician should not try to operate system upgrade, do not cut off

the power during upgrade process.

Restore

IP Camera Restore setting interface as shown in the follow figure:

 Restore: Restore the factory settings

 Reboot: Reboot the device

16

Exit

Click Logout to log out, as shown in the follow figure:

17

TELECAMERE SERIE IP 100

Leggere questo manuale prima dell’uso e conservarlo per consultazioni future

18

Dichiarazione

Le istruzioni qui contenute sono da considerarsi puramente indicative. Non tutti i modelli

supportano tutte le funzioni descritte.

Sebbene sia stata posta la massima cura nella preparazione del presente documento, le istruzioni

potrebbero contenere eventuali imprecisioni tecniche o errori tipografici.

Il prodotto o le procedure qui descritte possono subire modifiche o aggiornamenti in qualsiasi momento

senza preavviso.

Le schermate utilizzate nelle istruzioni sono riportate solamente a fini indicativi e illustrativi.

Per eventuali dubbi o per richiedere la documentazione relativa ai prodotti più recenti e note

complementari, consultare il servizio di assistenza post-vendita.

Precauzioni

Le seguenti precauzioni devono essere osservate rigorosamente per un corretto utilizzo del prodotto e la

prevenzione dei rischi e delle perdite materiali.

Utilizzare le telecamere in un ambiente caratterizzato da valori ammissibili di umidità e temperature.

Verificare se l'alimentatore funziona normalmente prima dell'utilizzo.

Non colpire violentemente il prodotto e fare attenzione a non farlo cadere né rovesciarlo.

Non installare il prodotto in luoghi polverosi o umidi oppure caratterizzati dalla presenza di intense

radiazioni elettromagnetiche.

Non collocare un contenitore o altri recipienti contenenti liquidi sul prodotto ed evitare che penetrino

liquidi all'interno del prodotto.

Quando il prodotto non viene utilizzato, installare il parapolvere di sicurezza per il sensore di immagine.

Non smontare il prodotto senza autorizzazione.

La pagina sta caricando ...

Comelit 100 Series Manuale utente

Questo manuale è adatto anche per

Comelit 100 Series Manuale utente

in altre lingue

Documenti correlati

Altri documenti