HP 9200c Manuale del proprietario

HP 9200c Digital Sender

Get

ting Started Guide

Guide de mise en route

Kurzanleitung

Guida introduttiva

Guía de instalación

inicial

Beknopte handleiding

Guia de primeiros passos

HP 9200C Digital Sender

Getting Started Guide

English

Copyright and License

Development Company, LP

Reproduction, adaptation, or translation

without prior written permission is

prohibited, except as allowed under the

copyright laws.

The information contained in this document

is subject to change without notice.

The only warranties for HP products and

services are set forth in the express

warranty statements accompanying such

products and services. Nothing herein

should be construed as constituting an

additional warranty. HP shall not be liable

for technical or editorial errors or omissions

contained herein.

Part number: Q5916-90902

Edition 1, 11/2004

Trademark Credits

Microsoft® and Windows® are U.S.

registered trademarks of Microsoft

Corporation.

Pentium® is a registered trademark of Intel

Corporation or its subsidiaries in the United

States and other countries/regions.

Table of contents

1 Introduction

Where to look for information ....................................................................................................2

Installation checklist ..................................................................................................................2

Before you begin .......................................................................................................................3

2 Setup

Step 1. Unpack and check package contents ...........................................................................6

Step 2. Installation requirements and product parts .................................................................7

Environmental requirements ...............................................................................................7

System requirements ..........................................................................................................7

Identifying the product parts ...............................................................................................9

Step 3. Change the control-panel overlays .............................................................................10

Step 4. Unlock the scanner head ............................................................................................12

Step 5. Connect the network cable .........................................................................................13

Step 6. Connect the power cord .............................................................................................14

Step 7. Configure the control-panel settings ...........................................................................15

Configuring the control-panel language ...........................................................................15

Configuring the date and time ..........................................................................................15

Step 8. Assign the IP address .................................................................................................16

Finding the DHCP IP address ..........................................................................................16

Manually assigning an IP address ....................................................................................16

Step 9. Install and configure the software ...............................................................................17

Before you begin ...............................................................................................................17

To install the software .......................................................................................................17

Step 10. Verify the product installation ...................................................................................21

3 Troubleshooting and customer support

Troubleshooting ......................................................................................................................24

Customer support ....................................................................................................................27

FCC regulations ......................................................................................................................28

Index

ENWW Table of contents iii

English

iv ENWW

1

Introduction

Congratulations on your purchase of the HP 9200C Digital Sender, a valuable addition to

your content-management processes. The digital sender scans all kinds of documents and

then sends them to e-mail addresses, fax destinations, or network folders. The digital sender

can also be set up to send documents to workflow destinations, along with metadata files

containing workflow information that is captured at the device control panel. By using these

features, the digital sender can be the interface for a variety of content-management

programs including Microsoft® Share Point, Documentum, Filenet, and Lotus Domino. By

using additional software such as HP Autostore, the digital sender can also send a

document through a more complex workflow that includes components such as bar code

recognition or Optical Character Recognition (OCR).

The digital sender includes the following features:

● Digital sending—Send scanned files to e-mail addresses, fax destinations, network

folders, and workflow folders. Digital-sending functions are carried out by the HP Digital

Sending Software (HP DSS), which is included with the digital sender.

● Flatbed scanner—The letter/A4 size scanner can scan both black-and-white and color

documents, and can scan the full page area within 1 mm (0.04 inch) of the paper edge.

● Interactive touchscreen control panel—Intuitive onscreen menus and wizards help to

carry out digital-sending tasks.

● Automatic document feeder (ADF)—The legal-size ADF accepts up to 50 pages, and

includes built-in duplexing for scanning both sides of a double-sided document.

●

Memory—The device includes 128 megabytes (MB) of random access memory (RAM).

● Hard disk—The device comes with a 20-gigabyte (GB) internal hard drive for storing

documents and settings.

● Connectivity—A 10/100Base-T port and an enhanced input/output (EIO) expansion slot

are provided for connectivity.

● HP Jetdirect Inside—An HP Jetdirect embedded print server is integrated directly on

the device for reliable network connectivity.

ENWW 1

English

Where to look for information

Explore the following documentation sources to learn how to use the HP 9200C Digital

Sender.

Getting started guide (this document)—Provides step-by-step instructions for installing

and setting up the digital sender.

User guide and support guide—The HP 9200C Digital Sender User Guide (part number

Q5916-90910) contains information about using the digital sender and troubleshooting

problems. The HP 9200C Digital Sender Support Guide (part number Q5916-90930)

contains more detailed configuration and administration instructions. Both of these guides

are available on the documentation CD-ROM that came with the digital sender. They are

also available on the Web at http://www.hp.com/support/9200c.

Online Help—The HP MFP DSS Configuration Utility includes online help that contains

information about digital-sending options.

Installation checklist

This guide helps you set up and install your new product. For correct installation, complete

each step, in order.

Step 1: Unpack the product.

Step 2: Verify installation requirements and product parts.

Step 3: Change the control-panel overlays (optional).

Step 4: Unlock the digital-sender scanner head.

Step 5: Connect the network cable.

Step 6: Connect the power cord.

Step 7: Configure the control-panel settings.

2 Chapter 1 Introduction ENWW

Step 8: Assign the device IP address.

Step 9: Install and configure the software.

Step 10: Verify the product installation.

Before you begin

During the software installation procedure, you are prompted to configure the digital-send

options. In order to complete this configuration, you need the following information:

● The software license key from the label on the software CD-ROM

● The host name or Internet Protocol (IP) address of the simple mail transfer protocol

(SMTP) e-mail server that will be used to send e-mail from the digital sender

● The host name or IP address of the Lightweight Directory Access Protocol (LDAP)

server that will be used to retrieve e-mail addresses (optional)

● The paths for any folders that are to be set up for the send-to-folder feature

● The host name or IP address of the digital sender

ENWW Before you begin 3

English

4 Chapter 1 Introduction ENWW

2

Setup

Follow these steps to set up and configure the digital sender. If you need more detailed

information about how to use or configure the device, see the HP 9200C Digital Sender User

Guide or the HP 9200C Digital Sender Support Guide.

ENWW 5

English

Step 1. Unpack and check package contents

The following items ship in the box with the digital sender.

1

2

4

3

5

1 Getting started guide

2 HP DSS software and digital sender documentation CD-ROMs

3 Digital sender

4 Control panel overlays (optional)

5 Power cord

Follow these instructions to unpack the digital sender.

1. Lift the device out of its box and remove all shipping bags.

2. Remove all tape and packing material from the ADF.

3. Remove the protective film from the control-panel display.

6 Chapter 2 Setup ENWW

Step 2. Installation requirements and product parts

Ensure that the proper environmental and network conditions exist for the installation of the

digital sender.

Environmental requirements

● Stable environment with no temperature or humidity changes

● Room temperature of 0 to 40°C (32 to 104°F)

● Relative humidity of 15 to 80% noncondensing

● Sturdy, level surface

● Well-ventilated room with no exposure to chemicals or direct sunlight

Observe the following space requirements when installing the digital sender.

NOTE

The digital sender requires 90 mm (3.5 inches) of free space behind the device in order to

fully open the top.

System requirements

The following system specifications are required for this product.

Hardware requirements

The digital sending software has the following hardware requirements for a server supporting

less than 50 digital sending devices (MFPs or 9200C digital senders):

● A PC with a Pentium® 3 or higher processor

● 512 MB of RAM

ENWW Step 2. Installation requirements and product parts 7

English

The digital sending software has the following hardware requirements for a server supporting

50 to 250 digital sending devices:

● A PC with a 2 GHz Pentium® 4 or higher processor

● 1 GB of RAM

NOTE

You must have Administrative privileges on the server in order to install the software.

Network system requirements

The digital sending software has the following network requirements:

● Windows® 2000 Professional, Server, or Advanced Server; Windows XP Professional;

or Windows Server 2003 Standard or Enterprise Server

● Fast Ethernet 100Base-TX or Ethernet 10Base-T

● Access to an SMTP e-mail gateway

NOTE

It is highly recommended that the SMTP gateway be located on your own local area

network. However, you can configure your product for e-mail functionality even if your mail

services are provided by an outside Internet service provider (ISP) over a digital subscription

line (DSL).

● Access to a network LDAP server to support optional user authentication

8 Chapter 2 Setup ENWW

Identifying the product parts

The following illustrations show the location and names of the primary product parts.

1 Jam release button

2 Control panel

3 On/off switch

4 Output bin

5 ADF input bin

6 ADF cable

7 Control-panel cable

8

10/100Base-T network port

9

EIO port

10 Power connector

11 Scanner lock

12 Serial number

ENWW Step 2. Installation requirements and product parts 9

English

Step 3. Change the control-panel overlays

The device comes with overlays installed on the control panel, and overlays for different

languages might be included in the box. If necessary, use the following procedure to change

the control-panel overlays to support your preferred language.

1. Locate the two control-panel overlays.

2. Insert a small, flat-blade screwdriver or other thin tool in the slot at the top edge of one of

the overlays to pull the top away from the control panel.

3. Lift the overlay up and back to remove it from the product.

4. Position the new overlay over the control panel. Align the ends of the overlay with the

holes on the control panel and slide the overlay in.

10 Chapter 2 Setup ENWW

5. Snap the overlay firmly onto the control panel. Ensure that the overlay is flat against the

control panel.

6. Repeat steps 2 through 5 to change the second overlay.

ENWW Step 3. Change the control-panel overlays 11

English

Step 4. Unlock the scanner head

The scanner head is locked to prevent damage during shipping. Follow these instructions to

unlock it.

1. Open the top of the digital sender.

2. Unlock the scanner head.

3. Close the top of the digital sender.

12 Chapter 2 Setup ENWW

Step 5. Connect the network cable

Use the RJ-45 connector on the back of the device to connect the product to a Fast Ethernet

100Base-TX or Ethernet 10Base-T network.

ENWW Step 5. Connect the network cable 13

English

Step 6. Connect the power cord

1. Connect the power cord to the product power cord connector. Then connect the power

cord to an adequate alternating current (ac) outlet.

NOTE

This product can operate using either 110/120 volts (V), 60 hertz (Hz) power or 220/240 V,

50 Hz power.

2. Turn the product on by using the power button. After the product warms up, a prompt

appears asking you to configure your control-panel display language (see

Step 7.

Configure the control-panel settings).

14 Chapter 2 Setup ENWW

La pagina sta caricando ...

HP 9200c Manuale del proprietario

Questo manuale è adatto anche per

HP 9200c Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti