Samsung HW-Q90R Manuale utente

HW-Q90R

FULL MANUAL

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at www.samsung.com/register

ENG - ii

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

Refer to the table below for an explanation of

symbols which may be on your Samsung product.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage

is present inside. It is dangerous to

make any kind of contact with any

internal part of this product.

This symbol indicates that this product

has included important literature

concerning operation and maintenance.

Class II product : This symbol indicates

that it does not require a safety

connection to electrical earth (ground).

If this symbol is not present on a

product with a power cord, the product

MUST have a reliable connection to

protective earth (ground).

AC voltage : This symbol indicates that

the rated voltage marked with the

symbol is AC voltage.

DC voltage : This symbol indicates that

the rated voltage marked with the

symbol is DC voltage.

Caution, Consult instructions for use :

This symbol instructs the user to

consult the user manual for further

safety related information.

WARNING

• To reduce the risk of re or electric shock, do

not expose this appliance to rain or moisture.

CAUTION

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

• This apparatus shall always be connected to a

AC outlet with a protective grounding

connection.

• To disconnect the apparatus from the mains,

the plug must be pulled out from the mains

socket, therefore the mains plug shall be

readily operable.

• Do not expose this apparatus to dripping or

splashing. Do not put objects lled with

liquids, such as vases on the apparatus.

• To turn this apparatus off completely, you

must pull the power plug out of the wall

socket. Consequently, the power plug must

be easily and readily accessible at all times.

ENG - iii

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the bottom of your

product. Install your product horizontally, on

a suitable base (furniture), with enough

space around it for ventilation (7~10 cm).

Make sure the ventilation slots are not

covered. Do not place the unit on ampliers

or other equipment which may become hot.

This unit is designed for continuous use. To

fully turn off the unit, disconnect the AC plug

from the wall outlet. Unplug the unit if you

intend to leave it unused for a long period of

time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due

to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to

overheating and cause the unit to

malfunction.

4. Protect the product from moisture (i.e.

vases), and excess heat (e.g. a replace) or

equipment creating strong magnetic or

electric elds. Unplug the power cable from

the AC wall socket if the unit malfunctions.

Your product is not intended for industrial

use. It is for personal use only. Condensation

may occur if your product has been stored in

cold temperatures. If transporting the unit

during the winter, wait approximately

2 hours until the unit has reached room

temperature before using.

5. The battery used with this product contains

chemicals that are harmful to the

environment. Do not dispose of the battery

in the general household trash. Do not

expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery.

Danger of explosion if the battery is replaced

incorrectly. Replace only with the same or

equivalent type.

ABOUT THIS MANUAL

The user manual has two parts: this simple paper

USER MANUAL and a detailed FULL MANUAL you

can download.

USER MANUAL

See this manual for safety instructions,

product installation, components,

connections, and product specications.

FULL MANUAL

You can access the FULL MANUAL on

Samsung’s on-line customer support centre by

scanning the QR code. To see the manual on

your PC or mobile device, download the

manual in document format from Samsung’s

website. (http://www.samsung.com/support)

Design, specications, and App screen are subject to

change without prior notice.

ENG - iv

CONTENTS

01 Checking the Components 2

Inserting Batteries before using the Remote Control (AA batteries X 2)

-------------------------

2

02 Product Overview 3

Front Panel / Top Panel of the Soundbar ------------------------- 3

Bottom Panel of the Soundbar

-------------------------

4

03 Connecting the Soundbar 5

Connecting Electrical Power

-------------------------

5

Connecting the Soundbar to the Subwoofer and Surround Speakers

-------------------------

6

–

Recommended Speaker Layout ------------------------- 6

– Automatic connection between the Subwoofer or Surround

Speakers and the Soundbar

-------------------------

6

– Manually connecting the Subwoofer or Surround Speakers if

automatic connection fails

-------------------------

7

04 Connecting to your TV 9

Method 1. Connecting with a Cable

-------------------------

9

– Connecting a TV using an HDMI Cable

-------------------------

9

– Connecting using an Optical Cable

-------------------------

10

Method 2. Connecting Wirelessly

-------------------------

11

– Connecting a TV via Bluetooth

-------------------------

11

– Connecting via Wi-Fi

-------------------------

13

05 Connecting an External Device 15

Connecting using an HDMI Cable (Capable of Dolby Atmos decoding

and playback)

-------------------------

15

Connecting using an HDMI Cable

-------------------------

16

Connecting using an Optical Cable

-------------------------

17

06 Connecting a Mobile Device 18

Connecting via Bluetooth

-------------------------

18

Connecting via Wi-Fi (Wireless Network)

-------------------------

21

ENG - v

07 Connecting an Amazon product 23

Connect and use with an Amazon product (Amazon Echo) ------------------------- 23

Use voice commands to control the Soundbar

-------------------------

25

08 Using the Remote Control 26

How to Use the Remote Control

-------------------------

26

Adjusting the Soundbar volume with a TV remote control

-------------------------

29

Using the Hidden Buttons (Buttons with more than one function)

-------------------------

30

Output specications for the different sound effect modes

-------------------------

30

09 Installing the Wall Mount 31

Installation Precautions

-------------------------

31

Wallmount Components

-------------------------

31

Installing the Surround Speakers on a Wall (Sold Separately)

-------------------------

33

10 Installing the Soundbar above a TV Stand 34

Component

-------------------------

34

11 Software Update 34

12 Troubleshooting 35

13 Licence 36

14 Open Source Licence Notice 37

15 Important Notes About Service 37

16 SpecicationsandGuide 38

Specications

-------------------------

38

ENG - 2

01 CHECKING THE COMPONENTS

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

POWER

x 2

Soundbar Main Unit Remote Control

/ Batteries

Subwoofer Surround Speaker

(Left / Right)

1 2 3

x 2

Power Cord

(Subwoofer)

Power Cord

(Surround Speaker)

Power Cord

(Main Unit)

HDMI Cable Bracket-Wall

Mount

x 2

(M4 x L10)

x 2

x 4

Wall Mount Guide Holder-Screw Screw Rubber-Foot

• For more information about the power supply and power consumption, refer to the label attached

to the product. (Label: Bottom of the Soundbar Main Unit)

• The power components are labelled (

1, 2

, 3). For more information about power connections,

see page 5.

• To distinguish the left surround speaker from the right, check the label on the rear of each speaker.

• To purchase additional components or optional cables, contact a Samsung Service Centre or

Samsung Customer Care.

• The appearance of the accessories may differ slightly from the illustrations above.

Inserting Batteries before using the Remote Control (AA batteries X 2)

Slide the battery cover in the direction of the arrow

until it is completely removed. Insert 2 AA batteries

(1.5V) oriented so that their polarity is correct. Slide

the battery cover back into position.

ENG - 3

02 PRODUCT OVERVIEW

Front Panel / Top Panel of the Soundbar

Top

Panel

Position the product so that the

"Samsung Harman Kardon" logo

is located on the top.

󰟳 󰟴 󰟵

󰟶

󰟳

(Power) Button

Turns the power on and off.

• Auto Power Down Function

The unit turns off automatically in the following situations:

– In D.IN / HDMI 1 / HDMI 2 / WIFI / BT mode if there is no audio signal for 18 minutes.

󰟴

(Source) Button

Selects the source input mode.

Input mode Display

Optical Digital input D.IN

ARC (HDMI OUT) input D.IN  TV ARC (Auto conversion)

HDMI input HDMI 1 / HDMI 2

Wi-Fi mode WIFI

BLUETOOTH mode BT

󰟵

-/+ (Volume) Button

Adjusts the volume.

• When adjusted, the volume level appears on the Soundbar’s front display.

󰟶

Display

Displays the product’s status and current mode.

• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

• If you want to enjoy sound only from the Soundbar, you must turn off the TV’s speakers in the Audio

Setup menu of your TV. Refer to the owner’s manual supplied with your TV.

ENG - 4

Bottom Panel of the Soundbar

POWER

SERVICE

NETWORK

ID SET

(WOOFER/REAR)

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

POWER

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

SERVICE

NETWORK

ID SET

(WOOFER/REAR)

POWER

SERVICE

NETWORK

ID SET

(WOOFER/REAR)

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

POWER

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

SERVICE

NETWORK

ID SET

(WOOFER/REAR)

POWER

SERVICE

NETWORK

ID SET

(WOOFER/REAR)

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

POWER

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

SERVICE

NETWORK

ID SET

(WOOFER/REAR)

POWER

SERVICE

NETWORK

ID SET

(WOOFER/REAR)

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

POWER

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

SERVICE

NETWORK

ID SET

(WOOFER/REAR)

󰟳

󰟷

󰟸

󰟹

󰟵󰟴 󰟶

󰟳

POWER

Connect the Soundbar's AC power cord.

󰟴

ID SET (WOOFER/REAR)

Press to connect the Soundbar to surround speakers and a subwoofer wirelessly.

• Press and hold the Up button on the remote for 5 seconds to complete ID SET.

󰟵

NETWORK

Press to connect to a wireless network (Wi-Fi) via the SmartThings app.

󰟶

SERVICE

Connect a USB storage device to upgrade the product's software.

󰟷

DIGITAL AUDIO IN (OPTICAL)

Connect to the digital (optical) output of an external device.

󰟸

HDMI IN 1 / HDMI IN 2

Inputs digital video and audio signals simultaneously using an HDMI cable.

Connect to the HDMI output of an external device.

󰟹

HDMI OUT (TV-ARC)

Connect to the HDMI (ARC) jack on a TV.

• When disconnecting the power cord from a wall outlet, pull the plug. Do not pull the cable.

• Do not connect this unit or other components to an AC outlet until all connections between

components are complete.

ENG - 5

03 CONNECTING THE SOUNDBAR

Connecting Electrical Power

Use the power components (1, 2

, 3

) to connect the Subwoofer, Surround Speaker, and Soundbar to an

electrical outlet in the following order:

1 Connect the power cord to the Subwoofer.

2 Connect the power cord to the Left and Right Surround Speakers.

3

Connect the power cord to the Soundbar.

See the illustrations below.

• For more information about the required electrical power and power consumption, refer to the

label attached to the product. (Label: Bottom of the Soundbar Main Unit)

POWER

Rear of Subwoofer

1 Power Cord

Connecting

Electrical Power

POWER

Bottoms of the Left

and Right Surround

Speakers

2 Power Cord

Connecting

Electrical Power

Bottom of the Soundbar

Main Unit

POWER

SERVICE

NETWORK

ID SET

(WOOFER/REAR)

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

POWER

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

SERVICE

NETWORK

ID SET

(WOOFER/REAR)

POWER

Connecting Electrical Power

3 Power Cord

POWER

ENG - 6

Connecting the Soundbar to the Subwoofer and Surround Speakers

When the Subwoofer is connected, you can enjoy rich bass sound.

Recommended Speaker Layout

150° 150°

135° 135°

0°

Subwoofer

Soundbar

Surround Speaker L Surround Speaker R

CAUTION

• Wireless receiving antennas are built

into the wireless subwoofer and

surround speakers. Keep the units

away from water and moisture.

• For optimal listening performance,

make sure that the areas around the

wireless subwoofer and surround

speakers locations are clear of any

obstructions.

Automatic connection between the Subwoofer or Surround Speakers and the Soundbar

The subwoofer and/or Surround speakers will connect to the Soundbar automatically if they are

plugged in to electrical outlets.

• When auto pairing is complete, the blue indicators at the rear of the Subwoofer or Surround

Speaker turn on.

LED Indicator Lights on the Rear of Subwoofer and Surround Speakers

LED Status Description Resolution

Blue

On

Successfully connected

(normal operation)

-

Blinking Recovering the connection

Check if the power cable attached to the

main Soundbar unit is connected properly

or wait about 5 minutes. If blinking persists,

try manually connecting the subwoofer.

See page 7.

Red On

Standby (with the Soundbar

main unit turned off)

Check if the power cable attached to the

main Soundbar unit is connected properly.

Connection failed

Connect again. See the instructions for

manual connection on page 7.

Red and

blue

Blinking Malfunction

See the contact information for the

Samsung Service Centre in this manual.

ENG - 7

Manually connecting the Subwoofer or Surround Speakers if automatic connection fails

Before performing the manual connection procedure below:

• Check whether the power cables for the Soundbar and subwoofer or Surround Speakers are

connected properly.

• Make sure that the Soundbar is turned on.

1. Press and hold ID SET on the rear of the subwoofer and surround speakers for at least 5 seconds.

• The red indicator on the rear of each speaker turns off and the blue indicator blinks.

5 Sec

Rear of Subwoofer

Blue LED Blinking Fast

POWER

x 2

Rear of the Left and Right Surround Speakers

5 Sec

2. Press and hold the Up button on the remote control for at least 5 seconds.

• The ID SET message appears on the display of the Soundbar for a moment, and then it

disappears.

• The Soundbar will automatically power on when ID SET is complete.

SOUND

MODE

PAIR

5 Sec

ID SET

“Samsung Harman Kardon” logo is on the top

ENG - 8

3. Check if the LINK LED is solid blue (connection complete).

LINK LED - Blue is On

When the connection is successfully

established, the blue indicators on the rear

of the subwoofer and surround speakers

turn on without blinking.

NOTES

• Do not connect the power cord of this product or your TV to a wall outlet until all connections

between components are complete.

• Before moving or installing this product, be sure to turn off the power and disconnect the power cord.

• If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the

STANDBY LED on the rear of the sub-woofer will turn red after blinking in blue several times.

• If you use a device that uses the same frequency (5.8GHz) as the Soundbar near the Soundbar,

interference may cause some sound interruption.

• The maximum transmission distance of the main unit’s wireless signal is about 10 meters, but may

vary depending on your operating environment. If a steel-concrete or metallic wall is between the

main unit and the wireless subwoofer, the system may not operate at all because the wireless

signal cannot penetrate metal.

PRECAUTIONS

• Wireless receiving antennas are built into the wireless subwoofer. Keep the unit away from water

and moisture.

• For optimal listening performance, make sure that the area around the wireless subwoofer and

surround speakers location is clear of any obstructions.

ENG - 9

04 CONNECTING TO YOUR TV

Hear TV sound from your Soundbar through wired or wireless connections.

• When the Soundbar is connected to selected Samsung TVs, the Soundbar can be controlled using

the TV’s remote control.

– This feature is available on 2017 and later Samsung Smart TVs that support Bluetooth when

the Soundbar is connected to the TV using an optical cable.

– This function also allows you to use the TV menu to adjust the sound eld and various settings

as well as the volume and mute.

Method 1. Connecting with a Cable

When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on

your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on

the TV is changed, you will experience better sound quality. (The TV menu may use different words for

Dolby Digital and PCM depending on the TV manufacturer.)

Connecting a TV using an HDMI Cable

HDMI OUT

(TV-ARC)

HDMI IN

(ARC)

Connect to the HDMI IN

(ARC) port of your TV.

HDMI Cable

Bottom of the Soundbar

Connect to the HDMI OUT (TV-ARC)

port of the Soundbar main unit.

󰟳

󰟴

TV ARC

Top of the Soundbar

1. With the Soundbar and TV turned on, connect the HDMI cable as shown in the gure.

2. “TV ARC” appears in the display window of the Soundbar main unit and the Soundbar plays TV

sound.

• If TV sound is inaudible, press the (Source) button on the remote control or on the top of

the Soundbar to switch to “D.IN” mode. The screen displays “D.IN” and “TV ARC” in sequence,

and TV sound is played.

ENG - 10

• If “TV ARC” does not appear in the display window of the Soundbar main unit, conrm that the

HDMI cable is connected to the correct port.

• Use the volume buttons on the TV’s remote control to change the volume on the Soundbar.

NOTES

• HDMI is an interface that enables the digital transmission of video and audio data with just a single

connector.

• If the TV provides an ARC port, connect the HDMI cable to the HDMI IN (ARC) port.

• We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one

whose diameter is less than 14 mm.

• Anynet+ must be turned on.

• This function is not available if the HDMI cable does not support ARC.

Connecting using an Optical Cable

Bottom of the Soundbar

OPTICAL OUT

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

󰟴

󰟳

D.IN

Optical Cable

(not supplied)

Top of the Soundbar

1. Connect the DIGITAL AUDIO IN (OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV

with a digital optical cable (not supplied).

2. Press the (Source) button on the top panel or on the remote control, and then select the “D.IN”

mode.

ENG - 11

Auto Power Link

Auto Power Link automatically turns on the Soundbar when the TV is turned on.

1. Connect the Soundbar and a TV with a digital optical cable (not supplied).

2. Press the Left button on the remote control for 5 seconds to turn Auto Power

Link on or off.

• Auto Power Link is set to ON by default.

(To turn off this function, press the Left button on the remote for 5 seconds.)

• Depending on the connected device, Auto Power Link may not function.

• This function is only available in the “D.IN” mode.

Method 2. Connecting Wirelessly

Connecting a TV via Bluetooth

When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.

• Only one TV can be connected at a time.

SOUND

MODE

PAIR

OR

Top of the Soundbar

The initial connection

1. Press the PAIR button on the remote control to enter the “BT PAIRING” mode.

(OR)

a. Press the (Source) button on the top panel and then select “BT”.

“BT” changes to “BT READY” in a few seconds automatically if there is no Bluetooth device

connected to the Soundbar.

b. When “BT READY” appears, press and hold the (Source) button on the top panel of the

Soundbar for more than 5 seconds to display “BT PAIRING”.

2. Select Bluetooth mode on the TV. (For more information, see the TV’s manual.)

3. Select “[AV] Samsung Soundbar Q90R” from the list on TV’s screen.

An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV’s Bluetooth device

list. To connect the TV to the Soundbar, select the message, and then establish a connection.

• When the TV is connected, [TV Name] → “BT” appears on the Soundbar’s front display.

4. You can now hear TV sound from the Soundbar.

ENG - 12

If the device fails to connect

• If a previously connected Soundbar (e.g. “[AV] Samsung Soundbar Q90R”) appears in the list, delete

it.

• Then repeat steps 1 through 3.

NOTE

• After you have connected the Soundbar to your TV the rst time, use the “BT READY” mode to

reconnect.

Disconnecting the Soundbar from the TV

Press the (Source) button on the top panel or on the remote control and switch to any mode but “BT”.

• Disconnecting takes time because the TV must receive a response from the Soundbar.

(The time required may differ, depending on the TV model.)

• To cancel the automatic Bluetooth connection between the Soundbar and TV, press the

p (Play/Pause) button on the remote control for 5 seconds with the Soundbar in “BT READY” status.

(Toggle On → Off)

What is the difference between BT READY and BT PAIRING?

• BT READY : In this mode, you can search for previously connected TVs or connect a previously

connected mobile device to the Soundbar.

• BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the PAIR button

on the remote control or press and hold the (Source) button on the top of the Soundbar for

more than 5 seconds while the Soundbar is in “BT” mode.)

NOTES

• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.

• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the

Soundbar and the Bluetooth device exceeds 10 meters.

• The Soundbar automatically turns off after 18 minutes in the Ready state.

• The Soundbar may not perform Bluetooth search or connection correctly under the following

circumstances:

– If there is a strong electrical eld around the Soundbar.

– If several Bluetooth devices are simultaneously paired with the Soundbar.

– If the Bluetooth device is turned off, not in place, or malfunctions.

• Electronic devices may cause radio interference. Devices that generate electromagnetic waves

must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.

ENG - 13

Connecting via Wi-Fi

Pre-connection Checklist

1. Conrm that your Samsung Smart TV was released after 2013. This function is compatible only

with Samsung Smart TVs released after 2013.

2. Make sure your Wireless router (Wi-Fi) is ready and working.

3. Make sure that the TV is connected to the Wireless router (your Wi-Fi network).

Top of the Soundbar

Step 1 : Connecting the Soundbar to Wi-Fi

1. Press the (Source) button on the top of the Soundbar or on the remote control to select “WIFI”

mode.

• When using selected Samsung TVs (2016 ~ 2018 Samsung Smart TVs that support Bluetooth.)

– If you select “WIFI” mode when the TV is turned on, the TV screen displays a pop-up

window providing instructions on how to automatically connect the Soundbar to a wireless

router (Wi-Fi). Refer to the instructions in the pop-up window of the TV.

Top of the Soundbar

WIFI

2. Connect your mobile device (smartphone, tablet, etc.) to the Wi-Fi network the TV is connected to.

ENG - 14

3. Install and launch the SmartThings app on your mobile device (smartphone, tablet, etc.).

SmartThings app

iOSAndroid

4. Follow the instructions in the app screen on the mobile device to connect the Soundbar to your

Wi-Fi network.

Step2:ConguringSettingsontheTV

• If the TV disconnects from your wireless network after you change the input source to the

Soundbar, use the TV menu to connect the TV to the network again.

For TVs released in 2019

Home ( )  Settings ( )  Sound  Sound Output  [AV] Samsung Soundbar Q90R (Wi-Fi)

For TVs released in 2018

Home ( )  Settings ( )  Sound  Sound Output  [AV] Samsung Soundbar Q90R (Wi-Fi)

For TVs released in 2017

Home ( )  Settings ( )  Sound  Sound Output  [AV] Samsung Soundbar Q90R (Wi-Fi)

For TVs released in 2016

Home ( )  Settings ( )  Sound  Select Speaker  [AV] Samsung Soundbar Q90R (Wi-Fi)

For TVs released in 2015

Menu  Sound  Speaker List

For TVs released in 2014

Menu  Sound  Speaker Settings  Multiroom Link - Settings

NOTES

• The TV and Soundbar must be connected to the same wireless network (Wi-Fi).

• If your wireless router (Wi-Fi) uses a DFS channel, you will not be able to establish a Wi-Fi

connection between the TV and Soundbar. Contact your Internet service provider for details.

• If the 5GHz Wi-Fi connection is not smooth, use the 2.4GHz bandwidth.

• Because the menus may differ depending on the year of manufacture, refer to your TV manual.

ENG - 15

05 CONNECTING AN EXTERNAL DEVICE

Connect to an external device via a wired or wireless network to play the external device’s sound

through the Soundbar.

Connecting using an HDMI Cable (Capable of Dolby Atmos decoding

and playback)

• When you use Dolby Atmos®: If the input source is Dolby Atmos®, 7.1.4 channels are outputted.

When Dolby Atmos® is active, the Soundbar’s sound effect modes controlled by the SOUND MODE

button are not available.

• Important: This product supports Dolby Atmos® only in HDMI mode.

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

HDMI OUT

HDMI IN

(ARC)

Top of the Soundbar

OR

HDMI Cable

󰟳

󰟴

External Device

HDMI 1

OR

HDMI 2

Bottom of the Soundbar

1. Connect an HDMI cable from the HDMI IN 1 or HDMI IN 2 jack on the bottom of the Soundbar to the

HDMI OUT jack on your digital device.

2. Connect an HDMI cable from the HDMI OUT (TV-ARC) jack on the bottom of the Soundbar to the

HDMI IN jack on your TV.

3. Press the (Source) button on the top panel or on the remote control, and then select

“HDMI 1” or “HDMI 2”.

4. “HDMI 1” or “HDMI 2” mode is displayed on the Soundbar display panel and sound plays.

ENG - 16

NOTE

• When Dolby Atmos® is activated, “DOLBY ATMOS” appears in the front display.

ConguringDolbyAtmos®onyourBDplayerorotherdevice.

• Open the audio output options on the settings menu of your BD player or other device and make

sure that “No Encoding” is selected for Bitstream. For example, on a Samsung BD Player, go to

Home Menu → Sound → Digital Output and then select Bitstream (unprocessed).

• If the Audio Output options include Secondary Audio, make sure Secondary Audio is set to Off.

• Make sure that the content supports Dolby Atmos®.

Connecting using an HDMI Cable

DIGITAL AUDIO IN

(OPTICAL)

HDMI IN 1

HDMI IN 2

HDMI OUT

(TV-ARC)

HDMI OUT

HDMI IN

(ARC)

Top of the Soundbar

OR

HDMI Cable

󰟳

󰟴

External Device

HDMI 1

OR

HDMI 2

Bottom of the Soundbar

1. Connect an HDMI cable from the HDMI IN 1 or HDMI IN 2 jack on the bottom of the Soundbar to the

HDMI OUT jack on your digital device.

2. Connect an HDMI cable from the HDMI OUT (TV-ARC) jack on the bottom of the Soundbar to the

HDMI IN jack on your TV.

3. Press the (Source) button on the top panel or on the remote control, and then select

“HDMI 1” or “HDMI 2”.

4. “HDMI 1” or “HDMI 2” mode is displayed on the Soundbar display panel and sound plays.

La pagina sta caricando ...

Samsung HW-Q90R Manuale utente

Samsung HW-Q90R Manuale utente

in altre lingue

Documenti correlati

Altri documenti