ABB M2L series Installation, Operation & Maintenance Manual

Installation, operation, maintenance and safety manual .......................................................................................... EN 3

Montage-, Betriebs-, Wartungs- und Sicherheitsanleitung .................................................................................... DE 21

Manuel d’installation, d’exploitation, de maintenance et de sécurité ..................................................................... FR 39

Manual de instalación, funcionamiento, mantenimiento y seguridad ..................................................................... ES 59

Manuale d’installazione, funzionamento e manutenzione ........................................................................................ IT 79

Manual de instalação, operação, manutenção e segurança ...................................................................................PT 99

Installations-, driffts-, underhålls- och säkerhetsmanual ..................................................................................... SV 119

Asennus-, käyttö-, kunnossapito- ja turvallisuusohje ............................................................................................ FI 137

More languages – see web site www.abb.com/motors&generators > Motors > Document library

Low voltage motors

Manual

Layout of EC Declaration of Conformity

The Manufacturer: (Name and address of the manufacturer)

hereby declares that

The Products: (Product identication)

are in conformity with the corresponding essential requirements of following EC directive:

Directive 2006/95/EC (of 12 December 2006).

The motors are in conformity with provisions of the harmonized standard EN 60 034-1(2010) which thus

comply with Principal Elements of the Safety Objectives for Electrical Equipment stated in Annex I of

said directive.

Note: When installing motors for converter supply applications, additional requirements must be

respected regarding the motor as well as the installation, as described in installation manual delivered

with converters.

Directive 2009/125/EC (of 21

st

October 2009).

The motors are in conformity with requirements set in the Regulation (EC) N° 640/2009

dated of 22 July 2009.

Efciency class is dened according to the standard EN 60034-30 : March 2009.

Year of CE marking :

Signed by

____________________________

Title ____________________________

Date ____________________________

2 ABB Motors and Generators | Low voltage motor manual 01-2009

1. Introduction ............................................................................................................................................. 5

1.1 Declaration of Conformity .................................................................................................................. 5

1.2 Validity .............................................................................................................................................. 5

2. Handling ................................................................................................................................................... 6

2.1 Reception check ............................................................................................................................... 6

2.2 Transportation and storage ............................................................................................................... 6

2.3 Lifting ................................................................................................................................................ 6

2.4 Machine weight ................................................................................................................................. 6

3. Installation and commissioning ............................................................................................................. 7

3.1 General ............................................................................................................................................. 7

3.2 Insulation resistance check ............................................................................................................... 7

3.3 Foundation ........................................................................................................................................ 7

3.4 Balancing and ﬁtting coupling halves and pulleys .............................................................................. 8

3.5 Mounting and alignment of the motor ................................................................................................ 8

3.6 Slide rails and belt drives ................................................................................................................... 8

3.7 Machines with drain plugs for condensation ...................................................................................... 8

3.8 Cabling and electrical connections .................................................................................................... 8

3.8.1 Connections for different starting methods ............................................................................. 9

3.8.2 Connections of auxiliaries ....................................................................................................... 9

3.9 Terminals and direction of rotation ..................................................................................................... 9

4. Operation ............................................................................................................................................... 10

4.1 Use ................................................................................................................................................. 10

4.2 Cooling ........................................................................................................................................... 10

4.3 Safety considerations ...................................................................................................................... 10

Low Voltage Motors

Installation, operation, maintenance and safety manual

List of Contents Page

Low voltage motor manual 01-2009 | ABB Motors and Generators EN-3

5. Low voltage motors in variable speed operation .............................................................................. 11

5.1 Introduction ..................................................................................................................................... 11

5.2 Winding insulation ........................................................................................................................... 11

5.2.1 Phase to phase voltages ...................................................................................................... 11

5.2.1 Phase to ground voltages .................................................................................................... 11

5.2.3 Selection of winding insulation for ACS550- and ACS800-converters ................................... 11

5.2.4 Selection of winding insulation with all other converters ........................................................ 11

5.3 Thermal protection of windings ....................................................................................................... 11

5.4 Bearing currents .............................................................................................................................. 12

5.4.1 Elimination of bearing currents with ABB ACS550 and ACS800 converters .......................... 12

5.4.2 Elimination of bearing currents with all other converters ........................................................ 12

5.5 Cabling, grounding and EMC .......................................................................................................... 12

5.6 Operating speed ............................................................................................................................. 12

5.7 Dimensioning the motor for variable speed application .................................................................... 12

5.7.1 General ................................................................................................................................ 12

5.7.2 Dimensioning with ABB ACS800 converters with DTC control .............................................. 12

5.7.3 Dimensioning with ABB ACS550 converters ......................................................................... 13

5.7.4 Dimensioning with other voltage source PWM-type converters ............................................. 13

5.7.5 Short time overloads ............................................................................................................ 13

5.8 Rating plates ................................................................................................................................... 13

5.9 Commissioning the variable speed application ................................................................................ 13

6. Maintenance .......................................................................................................................................... 14

6.1 General inspection .......................................................................................................................... 14

6.1.1 Standby motors ......................................................................................................................14

6.2 Lubrication ............................................................................................................................................... 14

6.2.1 Machines with permanently greased bearings ...................................................................... 14

6.2.2 Motors with regreasable bearings ......................................................................................... 15

6.2.3 Lubrication intervals and amounts ........................................................................................ 15

6.2.4 Lubricants ............................................................................................................................ 17

7. After Sales Support ............................................................................................................................... 18

7.1 Spare parts ..................................................................................................................................... 18

7.2 Rewinding ....................................................................................................................................... 18

7.3 Bearings ......................................................................................................................................... 18

8. Environmental requirements ................................................................................................................ 18

8.1 Noise levels ..................................................................................................................................... 18

9. Troubleshooting .................................................................................................................................... 19

EN-4 ABB Motors and Generators | Low voltage motor manual 01-2009

1. Introduction

NOTE!

These instructions must be followed to ensure safe

and proper installation, operation and maintenance

of the machine. They should be brought to the

attention of anyone who installs, operates or

maintains the machine or associated equipment.

The machine is intended for installation and use by

qualiﬁed personnel, familiar with health and safety

requirements and national legislation. Ignoring these

instructions may invalidate all applicable warranties.

1.1 Declaration of Conformity

Declarations of Conformity with respect to the Low voltage

Directive 73/23/EEC amended by Directive 93/68 EEC are

issued separately with individual machines.

The Declaration of Conformity also satisﬁes the

requirements of a Declaration of Incorporation with

respect to the Machinery Directive 98/37/EEC,

Art 4.2 Annex II, sub B

1.2 Validity

The instructions are valid for the following ABB electrical

machine types, in both motor and generator operation.

series MT*, MXMA,

series M2A*/M3A*, M2B*/M3B*, M4B*, M2C*/M3C*,

M2F*/M3F*, M2L*/M3L*, M2M*/M3M*, M2Q*,

M2R*/M3R*, M2V*/M3V*

in frame sizes 56 - 450.

There is a separate manual for e.g. Ex motors ‘Low voltage

motors for hazardous areas: Installation, operation and

maintenance Manual’ (Low Voltage Motors/Manual for Ex-

motors).

Additional information is required for some machine types

due to special application and/or design considerations.

Additional information is available for the following motors:

– roller table motors

– water cooled motors

– open drip proof motors

– smoke venting motors

– brake motors

– motors for high ambient temperatures

Low voltage motor manual 01-2009 | ABB Motors and Generators EN-5

2. Handling

2.1 Reception check

Immediately upon receipt check the motor for external

damage (e.g. shaft-ends and ﬂanges and painted surfaces)

and if found, inform the forwarding agent without delay.

Check all rating plate data, especially voltage and winding

connection (star or delta). The type of bearing is speciﬁed

on the rating plate of all motors except the smallest frame

sizes.

2.2 Transportation and storage

The motor should always be stored indoors (above

–20°C), in dry, vibration free and dust free conditions.

During transportation, shocks, falls and humidity should be

avoided. In other conditions, please contact ABB.

Unprotected machined surfaces (shaft-ends and ﬂanges)

should be treated against corrosion.

It is recommended that shafts are rotated periodically by

hand to prevent grease migration.

Anti-condensation heaters, if ﬁtted, are recommended to

be used to avoid water condensing in the motor.

The motor must not be subject to any external vibrations at

standstill so as to avoid causing damage to the bearings.

Motors ﬁtted with cylindrical-roller and/or angular contact

bearings must be ﬁtted with locking devices during

transport.

2.3 Lifting

All ABB motors above 25 kg are equipped with lifting lugs

or eyebolts.

Only the main lifting lugs or eyebolts of the motor should be

used for lifting the motor. They must not be used to lift the

motor when it is attached to other equipment.

Lifting lugs for auxiliaries (e.g. brakes, separate cooling

fans) or terminal boxes must not be used for lifting the

motor.

Motors with the same frame may have a different center of

gravity because of different output, mounting arrangements

and auxiliary equipment.

Damaged lifting lugs must not be used. Check that

eyebolts or integrated lifting lugs are undamaged before

lifting.

Lifting eyebolts must be tightened before lifting. If needed,

the position of the eyebolt can be adjusted using suitable

washers as spacers.

Ensure that proper lifting equipment is used and that the

sizes of the hooks are suitable for the lifting lugs.

Care must be taken not to damage auxiliary equipment and

cables connected to the motor.

2.4 Machine weight

The total machine weight can vary within the same

frame size (center height) depending on different output,

mounting arrangement and auxiliaries.

The following table shows estimated maximum weights

for machines in their basic versions as a function of frame

material.

The actual weight of all ABB’s motors, except the smallest

frame sizes (56 and 63) is shown on the rating plate.

Frame

size

Aluminum

Weight

kg

Cast iron

Weight

kg

Steel

Weight

kg

Add.

for brake

56 4.5 - -

63 6 - -

71 8 13 5

80 12 20 8

90 17 30 10

100 25 40 16

112 36 50 20

132 63 90 30

160 95 130 30

180 135 190 45

200 200 275 55

225 265 360 75

250 305 405 75

280 390 800 600 -

315 - 1700 1000 -

355 - 2700 2200 -

400 - 3500 3000 -

450 - 4500 - -

EN-6 ABB Motors and Generators | Low voltage motor manual 01-2009

3. Installation and commissioning

WARNING

Disconnect and lock out before working on the

motor or the driven equipment.

3.1 General

All rating plate values must be carefully checked to ensure

that the motor protection and connection will be properly

done.

WARNING

In case of motors mounted with the shaft upwards

and water or liquids are expected to go down along

the shaft, the user must take in account to mount

some means capable of preventing it.

Remove transport locking if employed. Turn shaft by hand

to check free rotation if possible.

Motors equipped with roller bearings:

Running the motor with no radial force applied to the shaft

may damage the roller bearing.

Motors equipped with angular contact bearing:

Running the motor with no axial force applied in the right

direction in relation to the shaft may damage the angular

contact bearing.

WARNING

For machines with angular contact bearings the axial

force must not by any means change direction.

The type of bearing is speciﬁed on the rating plate.

Motors equipped with regreasing nipples:

When starting the motor for the ﬁrst time, or after long

storage, apply the speciﬁed quantity of grease.

For details, see section “6.2.2 Motors with regreasable

bearings”.

3.2 Insulation resistance check

Measure insulation resistance before commissioning and

when winding dampness is suspected.

WARNING

Disconnect and lock out before working on the

motor or the driven equipment.

Insulation resistance, corrected to 25°C, must exceed the

reference value, i.e. 100 MΩ (measured with 500 or 1000 V

DC). The insulation resistance value is halved for each 20°C

rise in ambient temperature.

WARNING

The motor frame must be grounded and the

windings should be discharged against the frame

immediately after each measurement to avoid risk of

electrical shock.

If the reference resistance value is not attained, the

winding is too damp and must be oven dried. The oven

temperature should be 90°C for 12-16 hours followed by

105°C for 6-8 hours.

Drain hole plugs, if ﬁtted, must be removed and closing

valves, if ﬁtted, must be opened during heating. After

heating, make sure the plugs are reﬁtted. Even if the drain

plugs are ﬁtted, it is recommended to disassemble the end

shields and terminal box covers for the drying process.

Windings drenched in seawater normally need to be

rewound.

3.3 Foundation

The end user has full responsibility for preparation of the

foundation.

Metal foundations should be painted to avoid corrosion.

Foundations must be even, see ﬁgure below, and

sufﬁciently rigid to withstand possible short circuit forces.

They must be designed and dimensioned to avoid the

transfer of vibration to the motor and vibration caused by

resonance.

Note! Height difference shall

not exceed ± 0,1mm referred

to any other motor foot

Ruler

Foot location

Low voltage motor manual 01-2009 | ABB Motors and Generators EN-7

3.4 Balancing and ﬁtting coupling

halves and pulleys

As standard, balancing of the motor has been carried out

using half key

When balancing with full key, the shaft is marked with

YELLOW tape, with the text “Balanced with full key”.

In case of balancing without key, the shaft is marked with

BLUE tape, with the text “Balanced without key”.

Coupling halves or pulleys must be balanced after

machining the keyways. Balancing must be done in

accordance with the balancing method speciﬁed for the

motor.

Coupling halves and pulleys must be ﬁtted on the shaft by

using suitable equipment and tools which do not damage

the bearings and seals.

Never ﬁt a coupling half or pulley by hammering or by

removing it using a lever pressed against the body of the

motor.

3.5 Mounting and alignment

of the motor

Ensure that there is enough space for free airﬂow around

the motor. Minimum requirements for free space behind the

motor fan cover can be found from the product catalog or

from the dimension drawings available from the web: see

www.abb.com/motors&generators.

Correct alignment is essential to avoid bearing, vibration

and possible shaft failures.

Mount the motor on the foundation using the appropriate

bolts or studs and place shim plates between the

foundation and the feet.

Align the motor using appropriate methods.

If applicable, drill locating holes and ﬁx the locating pins into

position.

Mounting accuracy of coupling half: check that clearance

b is less than 0.05 mm and that the difference a1 to a2 is

also less than 0.05 mm. See Figure 3.

Re-check the alignment after ﬁnal tightening of the bolts or

studs.

Do not exceed permissible loading values for bearings as

stated in the product catalogues.

3.6 Slide rails and belt drives

Fasten the motor to the slide rails as shown in Figure 2.

Place the slide rails horizontally on the same level.

Check that the motor shaft is parallel with the drive shaft.

Belts must be tensioned according to the instructions of

the supplier of the driven equipment. However, do not

exceed the maximum belt forces (i.e. radial bearing loading)

stated in the relevant product catalogues.

WARNING

Excessive belt tension will damage bearings and can

cause shaft damage.

3.7 Machines with drain plugs

for condensation

Check that drain holes and plugs face downwards.

Machines with sealable plastic drain plugs are delivered in

open position. In very dusty environments, all drain holes

should be closed.

3.8 Cabling and electrical

connections

The terminal box on standard single speed motors normally

contains six winding terminals and at least one earth

terminal.

In addition to the main winding and earthing terminals, the

terminal box can also contain connections for thermistors,

heating elements or other auxiliary devices.

Suitable cable lugs must be used for the connection of all

main cables. Cables for auxiliaries can be connected into

their terminal blocks as such.

Machines are intended for ﬁxed installation only. If not

otherwise speciﬁed, cable entry threads are metric. The IP-

class of the cable gland must be at least the same as those

of the terminal boxes.

Unused cable entries must be closed with blanking

elements according to the IP class of the terminal box.

The degree of protection and diameter are speciﬁed in the

documents relating to the cable gland.

EN-8 ABB Motors and Generators | Low voltage motor manual 01-2009

WARNING

Use appropriate cable glands and seals in the cable

entries according to the type and diameter of the

cable.

Additional information on cables and glands suitable for

variable speed applications can be found from chapter 5.5.

Earthing must be carried out according to local regulations

before the machine is connected to the supply voltage.

Ensure that the motor protection corresponds to the

environment and weather conditions; for example, make

sure that water cannot enter the motor or the terminal

boxes.

The seals of terminal boxes must be placed correctly in the

slots provided, to ensure the correct IP class.

3.8.1 Connections for different

starting methods

The terminal box on standard single speed motors normally

contains six winding terminals and at least one earth

terminal. This enables the use of DOL- or Y/D –starting.

See Figure 1.

For two-speed and special motors, the supply connection

must follow the instructions inside the terminal box or in the

motor manual.

The voltage and connection are stamped on the rating

plate.

Direct-on-line starting (DOL):

Y or D winding connections may be used.

For example, 690 VY, 400 VD indicates Y-connection for

690 V and D-connection for 400 V.

Star/Delta starting (Y/D):

The supply voltage must be equal to the rated voltage of

the motor when using a D-connection.

Remove all connection links from the terminal block.

Other starting methods and severe starting

conditions:

In case other starting methods are used, such as a soft

starter, or if starting conditions are particularly difﬁcult,

please consult ABB ﬁrst.

3.8.2 Connections of auxiliaries

If a motor is equipped with thermistors or other RTDs

(Pt100, thermal relays, etc.) and auxiliary devices, it is

recommended they be used and connected by appropriate

means. Connection diagrams for auxiliary elements and

connection parts can be found inside the terminal box.

Maximum measuring voltage for the thermistors is 2.5 V.

Maximum measuring current for Pt100 is 5 mA. Using a

higher measuring voltage or current may cause errors in

readings or damage the system.

The insulations of the winding thermal sensors is of basic

type. While connecting the sensors to control systems etc,

ensure adequate insulation or isolation, see IEC 60664.

NOTE!

Ensure the insulation level or isolation of thermistor

circuit, see IEC 60664.

3.9 Terminals and direction

of rotation

The shaft rotates clockwise when viewing the shaft face at

the motor drive end, and the line phase sequence - L1, L2,

L3 - is connected to the terminals as shown in Figure 1.

To alter the direction of rotation, interchange any two

connections on the supply cables.

If the motor has a unidirectional fan, ensure that it rotates in

the same direction as the arrow marked on the motor.

Low voltage motor manual 01-2009 | ABB Motors and Generators EN-9

4. Operation

4.2 Cooling

Check that the motor has sufﬁcient airﬂow. Ensure that no

nearby objects or direct sunshine radiate additional heat to

the motor.

For ﬂange mounted motors (e.g. B5, B35, V1), make sure

that the construction allows sufﬁcient air ﬂow on the outer

surface of the ﬂange.

4.3 Safety considerations

The machine is intended for installation and use by qualiﬁed

personnel, familiar with health and safety requirements and

national legislation.

Safety equipment necessary for the prevention of accidents

at the installation and operating site must be provided in

accordance with local regulations.

WARNING

Do not carry out work on motor, connection cables

or accessories such as frequency converters,

starters, brakes, thermistor cables or heating

elements when voltage is applied.

Points to observe

1. Do not step on the motor.

2. The temperature of the outer casing of the motor

may be too hot to touch during normal operation and

especially after shut-down.

3. Some special motor applications require special

instructions (e.g. using frequency converter supplies).

4. Be aware of rotating parts of the motor.

5. Do not open terminal boxes while energized.

4.1 Use

The motors are designed for the following conditions unless

otherwise stated on the rating plate.

- Normal ambient temperature limits are -20°C to +40°C.

- Maximum altitude 1000 m above sea level.

- Tolerance for supply voltage is ±5% and for frequency

±2% according to EN / IEC 60034-1 (2004).

The motor can only be used in applications it is intended

for. The rated nominal values and operational conditions

are shown on the motor rating plates. In addition, all

requirements of this manual and other related instructions

and standards must be followed.

If these limits are exceeded, motor data and construction

data must be checked. Please contact ABB for further

information.

WARNING

Ignoring any of given instructions or maintenance of

the apparatus may jeopardize the safety and thus

prevents the use of the machine.

EN-10 ABB Motors and Generators | Low voltage motor manual 01-2009

5. Low voltage motors in variable speed operation

5.1 Introduction

This part of the manual provides additional instructions for

motors used in frequency converter supply. Instructions

provided in this and respective manuals of selected

frequency converter must be followed to ensure safety and

availability of the motor.

Additional information may be required by ABB to decide

on the suitability for some machine types used in special

applications or with special design modiﬁcations.

5.2 Winding insulation

Variable speed drives cause higher voltage stresses than

the sinusoidal supply on the winding of the motor and

therefore the winding insulation of the motor as well as

the ﬁlter at the converter output must be dimensioned

according following instructions.

5.2.1 Phase to phase voltages

The maximum allowed phase to phase voltage peaks at

the motor terminal as a function of the rise time of the pulse

can be seen in Figure 1.

The highest curve “ABB Special Insulation” applies to

motors with a special winding insulation for frequency

converter supply, variant code 405.

The “ABB Standard Insulation” applies to all other motors

covered by this manual.

5.2.2 Phase to ground voltages

The allowed phase to ground voltage peaks at motor

terminals are:

Standard Insulation 1300 V peak

Special Insulation 1800 V peak

5.2.3 Selection of winding insulation for

ACS800 and ACS550 converters

In the case of ABB ACS800-series and ACS550-series

single drives with a diode supply unit (uncontrolled DC

voltage), the selection of winding insulation and ﬁlters can

be made according to table below:

Nominal supply

voltage U

N

of the

converter

Winding insulation and

ﬁlters required

U

N

≤ 500 V ABB Standard insulation

U

N

≤ 600 V ABB Standard insulation

+ dU/dt lters

OR

ABB Special insulation

(variant code 405)

U

N

≤ 690 V ABB Special insulation

(variant code 405)

AND

dU/dt-lters at converter

output

U

N

≤ 690 V

AND

cable length > 150 m

ABB Special insulation

(variant code 405)

For more information on resistor braking and converters

with controlled supply units, please contact ABB.

5.2.4 Selection of winding insulation

with all other converters

The voltage stresses must be limited below accepted limits.

Please contact the system supplier to ensure the safety of

the application. The inﬂuence of possible ﬁlters must be

taken into account while dimensioning the motor.

5.3 Thermal protection

Most of the motors covered by this manual are equipped

with PTC thermistors in the stator windings. It is

recommended to connect those to the frequency converter

by appropriate means. See also chapter 3.8.2.

Low voltage motor manual 01-2009 | ABB Motors and Generators EN-11

5.4 Bearing currents

Insulated bearings or bearing constructions, common

mode ﬁlters and suitable cabling and grounding methods

must be used according to the following instructions:

5.4.1 Elimination of bearing currents with

ABB ACS800 and ACS550 converters

In the case of the ABB ACS800 and ACS550-series

frequency converter with a diode supply unit, the following

methods must be used to avoid harmful bearing currents in

the motors:

Nominal Power (Pn)

and / or Frame size (IEC)

Preventive measures

Pn < 100 kW No actions needed

Pn ≥ 100 kW

OR

IEC 315 ≤ Frame size

≤ IEC 355

Insulated non-drive end

bearing

Pn ≥ 350 kW

OR

IEC 400 ≤ Frame size

≤ IEC 450

Insulated non-drive end

bearing

AND

Common mode ﬁlter at

the converter

Insulated bearings which have aluminum oxide coated

inner and/or outer bores or ceramic rolling elements,

are recommended. Aluminum oxide coatings shall also

be treated with a sealant to prevent dirt and humidity

penetrating into the porous coating. For the exact type of

bearing insulation, see the motor’s rating plate. Changing

the bearing type or insulation method without ABB’s

permission is prohibited.

5.4.2 Elimination of bearing currents

with all other converters

The user is responsible for protecting the motor and driven

equipment from harmful bearing currents. Instructions

described in Chapter 5.4.1 can be used as guideline, but

their effectiveness cannot be guaranteed in all cases.

5.5 Cabling, grounding and EMC

To provide proper grounding and to ensure compliance

with any applicable EMC requirements, motors above 30

kW shall be cabled by shielded symmetrical cables and

EMC glands, i.e. cable glands providing 360° bonding.

Also for smaller motors symmetrical and shielded cables

are highly recommended. Make the 360° grounding

arrangement at all the cable entries as described in the

instructions for the glands. Twist the cable shields into

bundles and connect to the nearest ground terminal/bus

bar inside the terminal box, converter cabinet, etc.

NOTE!

Proper cable glands providing 360° bonding must

be used at all termination points, e.g. at motor,

converter, possible safety switch, etc.

For motors of frame size IEC 280 and upward, additional

potential equalization between the motor frame and the

driven equipment is needed, unless both are mounted on

a common steel base. In this case, the high frequency

conductivity of the connection provided by the steel

base should be checked by, for example, measuring the

potential difference between the components.

More information about grounding and cabling of variable

speed drives can be found in the manual “Grounding and

cabling of the drive system” (Code: 3AFY 61201998).

5.6 Operating speed

For speeds higher than the nominal speed stated on the

motor’s rating plate or in the respective product catalogue,

ensure that either the highest permissible rotational speed

of the motor or the critical speed of the whole application is

not exceeded.

5.7 Dimensioning the motor

for variable speed application

5.7.1 General

In case of ABB’s frequency converters, the motors can

be dimensioned by using ABB’s DriveSize dimensioning

program. The tool is downloadable from the ABB website

(www.abb.com/motors&generators).

For application supplied by other converters, the motors

must be dimensioned manually. For more information,

please contact ABB.

The loadability curves (or load capacity curves) are based

on nominal supply voltage. Operation in under or over

voltage conditions may inﬂuence on the performance of the

application.

5.7.2 Dimensioning with ABB ACS800

converters with DTC control

The loadability curves presented in Figures 4a - 4d are valid

for ABB ACS800 converters with uncontrolled DC-voltage

and DTC-control. The ﬁgures show the approximate

maximum continuous output torque of the motors as a

function of supply frequency. The output torque is given

as a percentage of the nominal torque of the motor. The

values are indicative and exact values are available on

request.

NOTE!

The maximum speed of the motor must not be

exceeded!

EN-12 ABB Motors and Generators | Low voltage motor manual 01-2009

5.7.3 Dimensioning with ABB ACS550

converters

The loadability curves presented in Figures 5a - 5d are

valid for ABB ACS550 series converters. The ﬁgures show

the approximate maximum continuous output torque of

the motors as a function of supply frequency. The output

torque is given as a percentage of the nominal torque of

the motor. The values are indicative and exact values are

available on request.

NOTE!

The maximum speed of the motor must not be

exceeded!

5.7.4 Dimensioning with other voltage

source PWM-type converters

For other converters, which have uncontrolled DC

voltage and minimum switching frequency of 3 kHz,

the dimensioning instructions of ACS550 can be used

as guidelines, but it shall be noted, that the actual

thermal loadability can also be lower. Please contact the

manufacturer of the converter or the system supplier.

NOTE!

The actual thermal loadability of a motor may be

lower than shown by guideline curves.

5.7.5 Short time overloads

ABB motors can usually be temporarily overloaded as well

as used in intermittent duties. The most convenient method

to dimension such applications is to use the DriveSize tool.

5.8 Rating plates

The usage of ABB’s motors in variable speed applications

do not usually require additional rating plates and the

parameters required for commissioning the converter can

be found from the main rating plate. However, in some

special applications the motors can be equipped with

additional rating plates for variable speed applications and

those include following information:

- speed range

- power range

- voltage and current range

- type of torque (constant or quadratic)

- converter type and required minimum switching

frequency

5.9 Commissioning the variable

speed application

The commissioning of the variable speed application must

be done according to the instructions of the frequency

converter and local laws and regulations. The requirements

and limitations set by the application must also be taken

into account.

All parameters needed for setting the converter must be

taken from the motor rating plates. The most often needed

parameters are:

- Motor nominal voltage

- Motor nominal current

- Motor nominal frequency

- Motor nominal speed

- Motor nominal power

Note: In case of missing or inaccurate information, do not

operate the motor before ensuring correct settings!

ABB recommends using all the suitable protective features

provided by the converter to improve the safety of the

application. Converters usually provide features such as

(names and availability of features depend on manufacturer

and model of the converter):

- Minimum speed

- Maximum speed

- Acceleration and deceleration times

- Maximum current

- Maximum Torque

- Stall protection

Low voltage motor manual 01-2009 | ABB Motors and Generators EN-13

6. Maintenance

WARNING

Voltage may be connected at standstill inside the

terminal box for heating elements or direct winding

heating.

WARNING

The capacitor in single-phase motors can retain a

charge that appears across the motor terminals, even

when the motor has reached standstill.

WARNING

A motor with frequency converter supply may

energize even if the motor is at standstill.

6.1 General inspection

1. Inspect the motor at regular intervals, at least once a

year. The frequency of checks depends on, for example,

the humidity level of the ambient air and on the local

weather conditions. This can initially be determined

experimentally and must then be strictly adhered to.

2. Keep the motor clean and ensure free ventilation

airﬂow. If the motor is used in a dusty environment,

the ventilation system must be regularly checked and

cleaned.

3. Check the condition of shaft seals (e.g. V-ring or radial

seal) and replace if necessary.

4. Check the condition of connections and mounting and

assembly bolts.

5. Check the bearing condition by listening for any unusual

noise, vibration measurement, bearing temperature,

inspection of spent grease or SPM bearing monitoring.

Pay special attention to bearings when their calculated

rated life time is coming to an end.

When signs of wear are noticed, dismantle the motor,

check the parts and replace if necessary. When bearings

are changed, replacement bearings must be of the same

type as those originally ﬁtted. The shaft seals have to be

replaced with seals of the same quality and characteristics

as the originals when changing bearings.

In the case of the IP 55 motor and when the motor

has been delivered with a plug closed, it is advisable to

periodically open the drain plugs in order to ensure that

the way out for condensation is not blocked and allows

condensation to escape from the motor. This operation

must be done when the motor is at a standstill and has

been made safe to work on.

6.1.1 Standby motors

If the motor is in standby for a longer period of time on

a ship or in other vibrating environment the following

measures have to be taken:

1. The shaft must be rotated regularly every 2 weeks (to

be reported) by means of start up of the system. In case

a start up is not possible, due to any reason, at least

the shaft has to be turned by hand in order to achieve

a different position once a week. Vibrations caused by

other vessel's equipment will cause bearing pitting which

should be minimized by regular operation / hand turning.

2. The bearing must be greased while rotating the shaft

every year (to be reported). If the motor has been

provided with roller bearing at the driven end the

transport lock to be removed before rotating the shaft.

The transport locking must be remounted in case of

transportation.

3. All vibrations must be avoided to prevent a bearing from

failuring. All instructions in the motor instruction manual

for commissioning and maintenance have to be followed

additionally. The warranty will not cover the winding and

bearing damages if these instructions have not been

followed.

6.2 Lubrication

WARNING

Beware of all rotating parts!

WARNING

Grease can cause skin irritation and eye

inﬂammation. Follow all safety precautions speciﬁed

by the manufacturer.

Bearing types are speciﬁed in the respective product

catalogs and on the rating plate of all motors except

smaller frame sizes.

Reliability is a vital issue for bearing lubrication intervals.

ABB uses mainly the L

1

-principle (i.e. that 99% of the

motors are certain to make the life time) for lubrication.

6.2.1 Machines with permanently

greased bearings

Bearings are usually permanently greased bearings of 1Z,

2Z, 2RS or equivalent types.

As a guide, adequate lubrication for sizes up to 250 can be

achieved for the following duration, according to L

10

.

EN-14 ABB Motors and Generators | Low voltage motor manual 01-2009

Duty hours for permanently greased bearings at ambient

temperatures of 25 and 40° C are:

Lubrication intervals according to L

10

principle

Frame size Poles

Duty hours

at 25° C

Duty hours

at 40° C

56-63 2-8 40 000 40 000

71 2 40 000 40 000

71 4-8 40 000 40 000

80-90 2 40 000 40 000

80-90 4-8 40 000 40 000

100-112 2 40 000 32 000

100-112 4-8 40 000 40 000

132 2 40 000 27 000

132 4-8 40 000 40 000

160 2 40 000 36 000

160 4-8 40 000 40 000

180 2 38 000 38 000

180 4-8 40 000 40 000

200 2 27 000 27 000

200 4-8 40 000 40 000

225 2 23 000 18 000

225 4-8 40 000 40 000

250 2 16 000 13 000

250 4-8 40 000 39 000

Data valid at 50 Hz, for 60 Hz reduce values for 20 %.

These values are valid for permitted load values given in

the product catalog. Depending on application and load

conditions, see the applicable product catalog or contact

ABB.

Operation hours for vertical motors are half of the above

values.

6.2.2 Motors with regreasable bearings

Lubrication information plate and general lubrication

advice

If the machine is equipped with a lubrication information

plate, follow the given values.

On the lubrication information plate, greasing intervals

regarding mounting, ambient temperature and rotational

speed are deﬁned.

During the ﬁrst start or after a bearing lubrication a

temporary temperature rise may appear, approximately 10

to 20 hours.

Some motors may be equipped with a collector for old

grease. Follow the special instructions given for the

equipment.

A. Manual lubrication

Regreasing while the motor is running

– Remove grease outlet plug or open closing valve if ﬁtted.

– Be sure that the lubrication channel is open

– Inject the speciﬁed amount of grease into the bearing.

– Let the motor run for 1-2 hours to ensure that all excess

grease is forced out of the bearing. Close the grease

outlet plug or closing valve if ﬁtted.

Regreasing while the motor is at a standstill

If it is not possible to regrease the bearings while the

motors are running, lubrication can be carried out while the

machine is at a standstill.

– In this case use only half the quantity of grease and then

run the motor for a few minutes at full speed.

– When the motor has stopped, apply the rest of the

speciﬁed amount of grease to the bearing.

– After 1-2 running hours close the grease outlet plug or

closing valve if ﬁtted.

B. Automatic lubrication

The grease outlet plug must be removed permanently with

automatic lubrication or open closing valve if ﬁtted.

ABB recommends only the use of electromechanical

systems.

The amount of grease per lubrication interval stated in the

table should be multiplied by four if an automatic regreasing

system is used.

When 2-pole motors are automatically regreased, the note

concerning lubricant recommendations for 2-pole motors in

the Lubricants chapter should be followed.

6.2.3 Lubrication intervals and amounts

As a guide, adequate lubrication for motors with

regreasable bearings can be achieved for the following

duration, according to L

1

. For duties with higher ambient

temperatures please contact ABB. The formula to change

the L

1

values roughly to L

10

values: L

10

= 2.7 x L

1

.

Lubrication intervals for vertical machines are half of the

values shown in the table below.

The lubrication intervals are based on an ambient

temperature +25°C. An increase in the ambient

temperature raises the temperature of the bearings

correspondingly. The values should be halved for a 15°C

increase and may be doubled for a 15°C decrease.

In variable speed operation (i.e. frequency converter supply)

it is necessary to measure the bearing temperature for

the whole duty range and if exceeds 80°C, the lubrication

intervals should be halved for a 15°C increase in bearing

temperature. If the motor is operated at high speeds, it is

also possible to utilize so called high speed greases, see

chapter 6.2.4.

WARNING

The maximum operating temperature of the grease

and bearings, +110°C, must not be exceeded.

The designed maximum speed of the motor must

not be exceeded.

Low voltage motor manual 01-2009 | ABB Motors and Generators EN-15

Lubrication intervals according to L

1

principle

Frame

size

Amount

of grease

g/bearing

kW

3600

r/min

3000

r/min

kW

1800

r/min

1500

r/min

kW

1000

r/min

kW

500-900

r/min

Ball bearings

Lubrication intervals in duty hours

112 10 all 10000 13000 all 18000 21000 all 25000 all 28000

132 15 all 9000 11000 all 17000 19000 all 23000 all 26500

160 25 ≤ 18,5 9000 12000 ≤ 15 18000 21500 ≤ 11 24000 all 24000

160 25 > 18,5 7500 10000 > 15 15000 18000 > 11 22500 all 24000

180 30 ≤ 22 7000 9000 ≤ 22 15500 18500 ≤ 15 24000 all 24000

180 30 > 22 6000 8500 > 22 14000 17000 > 15 21000 all 24000

200 40 ≤ 37 5500 8000 ≤ 30 14500 17500 ≤ 22 23000 all 24000

200 40 > 37 3000 5500 > 30 10000 12000 > 22 16000 all 20000

225 50 ≤ 45 4000 6500 ≤ 45 13000 16500 ≤ 30 22000 all 24000

225 50 > 45 1500 2500 > 45 5000 6000 > 30 8000 all 10000

250 60 ≤ 55 2500 4000 ≤ 55 9000 11500 ≤ 37 15000 all 18000

250 60 > 55 1000 1500 > 55 3500 4500 > 37 6000 all 7000

280

1)

60 all 2000 3500 - - - - - - -

280

1)

60 - - - all 8000 10500 all 14000 all 17000

280 35 all 1900 3200 - - - -

280 40 - - all 7800 9600 all 13900 all 15000

315 35 all 1900 3200 - - - -

315 55 -

-

all 5900 7600 all 11800 all 12900

355 35 all 1900 3200 - - - -

355 70 -

-

all 4000 5600 all 9600 all 10700

400 40 all 1500 2700 - - - -

400 85 - - all 3200 4700 all 8600 all 9700

450 40 all 1500 2700 - - - -

450 95 - - all 2500 3900 all 7700 all 8700

Roller bearings

Lubrication intervals in duty hours

160 25 ≤ 18,5 4500 6000 ≤ 15 9000 10500 ≤ 11 12000 all 12000

160 25 > 18,5 3500 5000 > 15 7500 9000 > 11 11000 all 12000

180 30 ≤ 22 3500 4500 ≤ 22 7500 9000 ≤ 15 12000 all 12000

180 30 > 22 3000 4000 > 22 7000 8500 > 15 10500 all 12000

200 40 ≤ 37 2750 4000 ≤ 30 7000 8500 ≤ 22 11500 all 12000

200 40 > 37 1500 2500 > 30 5000 6000 > 22 8000 all 10000

225 50 ≤ 45 2000 3000 ≤ 45 6500 8000 ≤ 30 11000 all 12000

225 50 > 45 750 1250 > 45 2500 3000 > 30 4000 all 5000

250 60 ≤ 55 1000 2000 ≤ 55 4500 5500 ≤ 37 7500 all 9000

250 60 > 55 500 750 > 55 1500 2000 > 37 3000 all 3500

280

1)

60 all 1000 1750 - - - - - - -

280

1)

70 - - - all 4000 5250 all 7000 all 8500

280 35 all 900 1600 - - - -

280 40 - - all 4000 5300 all 7000 all 8500

315 35 all 900 1600 - - - -

315 55

- -

all 2900 3800 all 5900 all 6500

355 35 all 900 1600 - - - -

355 70

- -

all 2000 2800 all 4800 all 5400

400 40 all - 1300 - - - -

400 85 - - all 1600 2400 all 4300 all 4800

450 40 all - 1300 - - - -

450 95 - - all 1300 2000 all 3800 all 4400

1) M3AA

For motors M4BP 160 to 250 the interval may be increased by 30 %, up to a maximum of three calendar years.

The values in table above are valid also for sizes M4BP 280 to 355.

EN-16 ABB Motors and Generators | Low voltage motor manual 01-2009

6.2.4 Lubricants

WARNING

Do not mix different types of grease.

Incompatible lubricants may cause bearing damage.

When regreasing, use only special ball bearing grease with

the following properties:

– good quality grease with lithium complex soap and with

mineral- or PAO-oil

– base oil viscosity 100-160 cST at 40°C

– consistency NLGI grade 1.5 - 3 *)

– temperature range -30°C - +120°C, continuously.

*) For vertical mounted motors or in hot conditions a stiffer

end of scale is recommended.

The above mentioned grease speciﬁcation is valid if the

ambient temperature is above -30°C or below +55°C, and

the bearing temperature is below 110°C; otherwise consult

ABB regarding suitable grease.

Grease with the correct properties is available from all the

major lubricant manufacturers.

Admixtures are recommended, but a written guarantee

must be obtained from the lubricant manufacturer,

especially concerning EP admixtures, that admixtures do

not damage bearings or the properties of lubricants at the

operating temperature range.

WARNING

Lubricants containing EP admixtures are not

recommended in high bearing temperatures in frame

sizes 280 to 450.

The following high performance greases can be used:

- Esso Unirex N2 or N3 (lithium complex base)

- Mobil Mobilith SHC 100 (lithium complex base)

- Shell Gadus S5 V 100 2 (lithium complex base)

- Klüber Klüberplex BEM 41-132 (special lithium

base)

- FAG Arcanol TEMP110 (lithium complex base)

- Lubcon Turmogrease L 802 EP PLUS

(special lithium base)

- Total Multiplex S 2 A (lithium complex base)

NOTE!

Always use high speed grease for high speed 2-pole

machines where the speed factor is higher than

480,000 (calculated as Dm x n where Dm = average

bearing diameter, mm; n = rotational speed, r/min).

The high speed grease is also used in motor types

M2CA, M2FA, M2CG and M2FG, frame sizes 355 to

400 2-pole machines.

The following greases can be used for high speed cast iron

motors but not mixed with lithium complex greases:

- Klüber Klüber Quiet BQH 72-102 (polyurea base)

- Lubcon Turmogrease PU703 (polyurea base)

If other lubricants are used;

Check with the manufacturer that the qualities correspond

to those of the above mentioned lubricants. The lubrication

interval are based on the listed high performance greases

above. Using other greases can reduce the interval.

If the compatibility of the lubricant is uncertain, contact

ABB.

Low voltage motor manual 01-2009 | ABB Motors and Generators EN-17

7. After Sales Support

7.1 Spare parts

When ordering spare parts, the motor serial number, full

type designation and product code, as stated on the rating

plate, must be speciﬁed.

For more information, please visit our web site

www.abb.com/partsonline.

7.2 Rewinding

Rewinding should always be carried out by qualiﬁed repair

shops.

Smoke venting and other special motors should not be

rewound without ﬁrst contacting ABB.

7.3 Bearings

Special care should be taken with the bearings. These

must be removed using pullers and ﬁtted by heating or

using special tools for the purpose.

Bearing replacement is described in detail in a separate

instruction leaﬂet available from the ABB Sales Ofﬁce.

8. Environmental requirements

8.1 Noise levels

Most of ABB’s motors have a sound pressure level not

exceeding 82 dB(A) at 50 Hz .

Values for speciﬁc machines can be found in the relevant

product catalogues. At 60 Hz sinusoidal supply the values

are approximately 4 dB(A) higher compared to 50 Hz

values in product catalogues.

For sound pressure levels at frequency converter supply,

please contact ABB.

Sound pressure levels for all machines having separate

cooling systems and for series M2F*/M3F*, M2L*/M3L*,

M2R*/M3R*, M2BJ/M3BJ and M2LJ/M3LJ are indicated in

separate additional manuals.

EN-18 ABB Motors and Generators | Low voltage motor manual 01-2009

9. Troubleshooting

These instructions do not cover all details or variations in equipment nor provide for every possible condition to be met in

connection with installation, operation or maintenance. Should additional information required, please contact the nearest

ABB Sales Ofﬁce.

Motor troubleshooting chart

Your motor service and any troubleshooting must be handled by qualiﬁed persons who have proper tools and equipment.

TROUBLE CAUSE WHAT TO DO

Motor fails to start Blown fuses Replace fuses with proper type and rating.

Overload trips Check and reset overload in starter.

Improper power supply Check to see that power supplied agrees with motor rating plate and

load factor.

Improper line connections Check connections against diagram supplied with motor.

Open circuit in winding or control switch Indicated by humming sound when switch is closed. Check for loose

wiring connections.

Also ensure that all control contacts are closing.

Mechanical failure Check to see if motor and drive turn freely. Check bearings and

lubrication.

Short circuited stator

Poor stator coil connection

Indicated by blown fuses. Motor must be rewound. Remove end

shields, locate fault.

Rotor defective Look for broken bars or end rings.

Motor may be overloaded Reduce load.

Motor stalls One phase may be open Check lines for open phase.

Wrong application Change type or size. Consult equipment supplier.

Overload Reduce load.

Low voltage Ensure the rating plate voltage is maintained. Check connection.

Open circuit Fuses blown, check overload relay, stator and push buttons.

Motor runs and

then dies down

Power failure Check for loose connections to line, to fuses and to control.

Motor does

not come up to

nominal speed

Not applied properly Consult equipment supplier for proper type.

Voltage too low at motor terminals

because of line drop

Use higher voltage or transformer terminals or reduce load. Check

connections. Check conductors for proper size.

Starting load too high Check the start load of the motor.

Broken rotor bars or loose rotor Look for cracks near the rings. A new rotor may be required, as repairs

are usually temporary.

Open primary circuit Locate fault with testing device and repair.

Low voltage motor manual 01-2009 | ABB Motors and Generators EN-19

TROUBLE CAUSE WHAT TO DO

Motor takes too long to

accelerate and/or draws

high current

Excessive load Reduce load.

Low voltage during start Check for high resistance. Make sure that adequate cable

size is used.

Defective squirrel cage rotor Replace with new rotor.

Applied voltage too low Correct power supply.

Wrong rotation direction Wrong sequence of phases Reverse connections at motor or at switchboard.

Motor overheats while

running

Overload Reduce load.

Frame or ventilation openings may

be full of dirt and prevent proper

ventilation of motor

Open vent holes and check for a continuous stream of air

from the motor.

Motor may have one phase open Check to make sure that all leads are well connected.

Grounded coil Motor must be rewound

Unbalanced terminal voltage Check for faulty leads, connections and transformers.

Motor vibrates Motor misaligned Realign.

Weak support Strengthen base.

Coupling out of balance Balance coupling.

Driven equipment unbalanced Rebalance driven equipment.

Defective bearings Replace bearings.

Bearings not in line Repair motor.

Balancing weights shifted Rebalance motor.

Contradiction between balancing of

rotor and coupling (half key - full key)

Rebalance coupling or motor.

Polyphase motor running single phase Check for open circuit.

Excessive end play Adjust bearing or add shim.

Scraping noise Fan rubbing end shield or fan cover Correct fan mounting.

Loose on bedplate Tighten holding bolts.

Noisy operation Air gap not uniform Check and correct end shield ﬁts or bearing ﬁts.

Rotor unbalance Rebalance rotor.

Hot bearings Bent or sprung shaft Straighten or replace shaft.

Excessive belt pull Decrease belt tension.

Pulleys too far away from shaft shoulder Move pulley closer to motor bearing.

Pulley diameter too small Use larger pulleys.

Misalignment Correct by realignment of the drive.

Insufﬁcient grease Maintain proper quality and amount of grease in bearing.

Deterioration of grease or lubricant

contaminated

Remove old grease, wash bearings thoroughly in kerosene

and replace with new grease.

Excess lubricant Reduce quantity of grease, bearing should not be more than

half full.

Overloaded bearing Check alignment, side and end thrust.

Broken ball or rough races Replace bearing, clean housing thoroughly ﬁrst.

EN-20

ABB Motors and Generators | Low voltage motor manual 01-2009

La pagina sta caricando ...

ABB M2L series Installation, Operation & Maintenance Manual

ABB M2L series Installation, Operation & Maintenance Manual

in altre lingue

Documenti correlati

Altri documenti