Lutron Electronics QSGRM-16D Quick Installation And Operation Manual

LUTRON

with DALI

Quick Installation

and Operation

Guide

®

Please Read

The GRAFIK Eye QS with DALI control unit allows for control of both lights

and window treatments, without interfaces, using a single control unit.

Features include pushbutton scene recall, info screen that displays energy

savings and status, IR receiver, astronomic timeclock, contact closure input,

and engravable backlit buttons that are easy to find and operate. The built-in

DALI bus link can control up to 64 DALI devices.

Model Numbers: QSGRK-6D, QSGRK-8D, QSGRK-16D

QSGR-6D, QSGR-8D, QSGR-16D

QSGRM-6D, QSGRM-8D, QSGRM-16D

Ratings: 100 - 240 V 50/60 Hz 100 mA

CE 230 V 50/60 Hz 100 mA

Output: PELV (Class 2: USA) supply 24 V 150 mA

DALI Link: 18 V 250 mA

Contents

Features and Functions. . . . . . . . . . . . . . . . . . . . . . . 2

Wiring the GRAFIK Eye® QS with DALI

Overview of Line Voltage/Mains

and DALI Wiring . . . . . . . . . . . . . . . . . . . . . . . . . 3

Line Voltage Wiring Details. . . . . . . . . . . . . . . . . . 4

DALI Bus Wiring Details . . . . . . . . . . . . . . . . . . . . 5

Overview of PELV (Class 2: USA) Wiring . . . . . . . 6

QS Link Control Wiring Details. . . . . . . . . . . . . . . 7

Completing Installation . . . . . . . . . . . . . . . . . . 8

Programming Mode . . . . . . . . . . . . . . . . . . . . . . . 9

Wireless Mode. . . . . . . . . . . . . . . . . . . . . . . . .10

Zone Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

DALI Setup Overview: Build System . . . . . . . . . 12

DALI Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Associating Wireless Occupancy Sensors . .14

Occupancy Sensor Setup: Scene Mode . . . . . 15

Associating Wireless Daylight Sensors . . . . .16

Daylight Sensor Setup

Mode Assignment . . . . . . . . . . . . . . . . . . . . . . . . 17

Zone Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Group Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Scene Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .22

Troubleshooting: DALI Functions . . . . . . . . . .23

Warranty, Contact Information . . . . . . . . . . . .24

For additional information, see the complete

installation and operation guide at

www.lutron.com/qs

English

Español Italiano

Français Deutsch

OK

1 2

3

4

5

69 10

11 12

13

14

7

815 16

9-16

1-8

Info screen

Displays status or

programming functions

Scene buttons

With integral scene

indicator LEDs

Optional Shade

(window treatment) button

groups

Preset and raise/lower

buttons with integral LEDs

(maximum of 3 button

groups)

Zone numbers

Zone raise/lower buttons

Zone LEDs display current

lighting zone levels

Timeclock button

Displays current

timeclock info

OK button

Used for programming,

fade time

Infrared receiver

For handheld remote use

Master buttons

Temporarily raise and lower

lighting levels on unit

USB type mini B

For programming via PC

{

Hinged faceplate

Features and Functions of the GRAFIK Eye® QS with DALI

Page button

Switches between displaying

zones 1 to 8 and 9 to 16 on

16-zone unit

Note: 6-zone control unit will show only zones 1 through 6.

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 2

For additional information, see the complete installation and operation guide at www.lutron.com/qs

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 3

For additional information, see the complete installation and operation guide at www.lutron.com/qs

Wiring the GRAFIK Eye® QS with DALI:

Overview of Line Voltage/Mains and DALI Wiring

4,0 mm

2

(12 AWG)

each terminal

100 – 240 V

50 / 60 Hz

Distribution

Panel

Line Voltage/Mains

Cables and Load Wiring

D2

D1

D2

D1

To additional DALI

devices

DALI Bus Wiring

(See page 5 for complete wiring

specification)

Two 1,5 mm

2

(16 AWG)

each terminal

DALI devices: ballasts,

drivers, or interfaces

Two D1 and two D2 connections are

provided for ease of wiring, and to

provide two connecting points; there is

only one DALI link on the unit.

Note: Ballasts and other DALI devices

must NOT obtain power from a line

voltage output on the GRAFIK Eye QS

with DALI.

Distribution

Panel

L

N

L

N

Terminal labels:

L: Hot/Live

N: Neutral

: Ground

Wiring the GRAFIK Eye® QS with DALI:

Line Voltage Wiring Details

• Use properly certified cable for all line

voltage/mains cables.

• Proper short-circuit and overload

protection must be provided at the

distribution panel.

• Install in accordance with all local and

national electrical codes.

• PELV (Class 2: USA) terminals may be

temporarily unplugged for ease of IR,

occupancy sensor, and control wiring.

• Notice: Risk of damage to unit. Do not

connect line voltage/mains cable to PELV

(Class 2: USA) terminals.

Step 1: Install wallbox. Mount an 89 mm

(3,5 in) deep 4-gang U.S. wallbox on a

dry, flat indoor surface that is accessible

and allows for system programming and

operation. Allow at least 110 mm (4,5 in)

clearance above and below the faceplate

to ensure proper heat dissipation. Allow

25 mm (1 in) for faceplate overhang on

all sides.

Note: 4-gang wallbox available from

Lutron; P/N 241400.

Step 2: Check control unit wiring.

•

Earth/ground terminal connection must

be made as shown in wiring diagrams

(see page 3).

•

Do not mix different load types on the

same zone.

• Follow all local and national electrical

codes when installing PELV (Class 2:

USA) wiring with line voltage/mains wiring.

WARNING! Shock hazard. May

result in serious injury or death.

Always turn off circuit breaker or

remove main fuse from power

line before doing any work.

Before connecting the loads to

the GRAFIK Eye QS with DALI

control unit, test the loads for

short-circuits.

Step 3: Connect line voltage and loads

to control unit.

• Strip 8 mm (5/16 in) of insulation off the

line voltage/mains cables in the wallbox.

• Connect the line voltage/mains, ground,

and load wires to the appropriate

terminals on the back of the control unit.

L: Hot/Live

N: Neutral

: Ground

The recommended installation torque is

0,6 N∙m (5,0 in∙lbs) for line voltage/mains

connections and 0,6 N∙m (5,0 in∙lbs) for

the earth/ground connection.

Notice: Risk of damage to unit.

GRAFIK Eye QS with DALI control

units must be in stalled by a qual i fied

electrician in accordance with all applica-

ble reg u la tions and building codes.

Im prop er wiring can result in dam age to

control units or oth er equipment.

Note: To avoid over heat ing and pos-

si ble damage to equipment, do not

install control units to dim re cep ta cles,

mo tor-op erated ap pli ances, or flu o res-

cent lighting not equipped with DALI

electron ic dim ming ballasts, or other

DALI devices approved for your location.

Control units are de signed for res i den tial

and commercial use, for indoor use only.

LUTRON

Faceplate overhangs

wallbox on all sides;

allow 25 mm (1 in)

110 mm

(4,5 in)

8 mm

(5/16 in)

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 4

For additional information, see the complete installation and operation guide at www.lutron.com/qs

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 5

For additional information, see the complete installation and operation guide at www.lutron.com/qs

DALI bus wiring may be considered

NEC® Class 1 or PELV (Class 2: USA).

• NEC® Class 1: DALI bus wiring may be

run in the same conduit as mains voltage

wiring to fixtures.

• PELV (Class 2: USA): DALI bus wiring

must be separated from all mains and

NEC® Class 1 wiring.

• Consult applicable national and local

codes for compliance.

• Lutron recommends using two different

colours for D1 and D2 (DALI bus) wires.

This will prevent wiring mistakes in

junction boxes where several different

DALI bus wires combine. Use the

following instructions for wiring the DALI

bus.

• Each DALI link can have only 1 GRAFIK

Eye QS with DALI connected to it. No

additional DALI bus supplies can be on

the link.

• Up to 64 DALI devices can be connected

to the DALI link.

• No other devices may be connected to

the DALI link.

WARNING! Shock hazard.

May result in serious injury or

death.

Do not wire live. Interrupt

power via circuit breaker before

wiring and servicing the DALI bus

supply.

Step 1: Use the wire size chart at right to

determine which wire size to use based

on the length of the DALI bus.

Step 2: Wire the DALI bus from terminal

D1 and terminal D2 to all DALI devices.

Step 3: Separate DALI wiring from the

mains wiring. If wiring the DALI bus as

PELV (Class 2: USA), maintain proper

separation from mains and NEC® Class 1

wiring.

Step 4: Turn on circuit breaker to

energise.

DALI Bus

18 V

250 mA

Wiring the GRAFIK Eye® QS with DALI:

DALI Bus Wiring Details

Wiring Size and Bus Length

DALI bus wires D1 and D2 are not

polarity sensitive. DALI bus length is

limited by the wire gauge used for D1 and

D2 as follows:

Wire Gauge Maximum DALI Bus

Length

4,0 mm

2

12 AWG

671 m

2 200 ft

2,5 mm

2

14 AWG

427 m

1 400 ft

1,5 mm

2

16 AWG

275 m

900 ft

1,0 mm

2

18 AWG

175 m

570 ft

DALI bus wiring cables (1,5 mm

2

/

16 AWG) are available from Lutron, part

numbers C-CBL-216-GR-1 (non-plenum)

and C-PCBL-216-CL-1 (plenum).

Contact Closure Input Wiring

For settings, see complete installation and

operation guide at www.lutron.com/qs.

1 2

A B C

N H 1 2 3 4 5 6

1 2 3 4

1 2

A B C

1 2 3 4 5 6 L N

1 2 3 4

1 2

A B C

1 2 3 4 5 6 L N

Note: Use appropriate wire connecting devices

as specified by local codes.

Example:

Occupancy sensor

(maximum 1)

1: COM

2: 24 V *

3: MUX

4: MUX

Control Wiring

Wiring the GRAFIK Eye® QS with DALI:

Overview of PELV (Class 2: USA) Wiring

IR Wiring

From external

IR connection

(by others)

1,0 mm

2

(18 AWG)

each terminal

1,0 mm

2

(18 AWG)

each terminal

1: IR DATA

2: IR COM

A: CCI SIG

B: 24 V

C: CCI COM

To control stations,

window treatments,

or other GRAFIK Eye

QS control units

Data (terminals 3 and 4):

Twisted, shielded pair 0,5 mm

2

(22 AWG)

each terminal

Common and power (terminals 1 and 2):

Two 1,0 mm

2

(18 AWG) each terminal

* Do not connect terminal 2

between any GRAFIK Eye QS

and any other power supply,

including another

GRAFIK Eye

QS. See complete installation

and operation guide at www.

lutron.com/qs. for detailed wiring

example.

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 6

For additional information, see the complete installation and operation guide at www.lutron.com/qs

• System communication uses PELV (Class 2: USA)

wiring.

• Follow all local and national electrical codes when

installing PELV (Class 2: USA) wiring with line

voltage/mains wiring.

• Each terminal accepts up to two 1,0 mm

2

(18 AWG)

wires.

• Total length of control link must not exceed

610 m (2 000 feet).

• Make all connections in the control unit’s wallbox.

• Wiring can be T-tapped or daisy-chained.

• Wire sizes:

- Two 1,0 mm

2

(18 AWG) conductors for control

power.

- One twisted, shielded pair of 0,5 mm

2

(22 AWG) for

data link.

- Cable is available from Lutron:

GRX-CBL-346S-500 (non-plenum) and

GRX-PCBL-346S-500 (plenum). Check

compatibility in your area.

• PELV (Class 2: USA) 24 V 150 mA.

QS smart

power

panel

LUTRON

LUTRONLUTRON

LUTRON

T-Tap Wiring Example

GRAFIK Eye QS

with DALI

Sivoia QS

seeTouch QS

Wiring the GRAFIK Eye® QS with DALI:

QS Link Control Wiring Details

To DALI link 1

To DALI link 2

System Limits

The QS wired communication link is limited to 100 devices or 100 zones. Please

note the zone count and power draw unit information in the following table.

QS Device Zone

Count

Power Draw Units

(supplied)

Power Draw

Units (consumed)

3-zone

GRAFIK Eye QS 3 3 0

4-zone

GRAFIK Eye QS 4 3 0

6-zone

GRAFIK Eye QS 6 3 0

8-zone

GRAFIK Eye QS 8 3 0

16-zone

GRAFIK Eye QS 16 3 0

seeTouch

® QS 0 0 1

International seeTouch

®

QS

0 0 1

Sivoia

® QS 1 0 (Refer to Spec.

Submittal)

Contact closure interface 5 0 3

Network interface 0 0 2

DMX interface 0 0 2

QS smart power panel 0 (Refer to Spec.

Submittal)

0

QS link power supply 0 8 0

LUTRON

LUTRONLUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

LUTRONLUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

LUTRONLUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

5.26

4.263.75

2.50

1.06

5.26

4.263.75

2.50

1.06

LUTRON

LUTRONLUTRON

LUTRON

GRAFIK Eye QS

with DALI

Sivoia

QS

seeTouch QS

Daisy-Chain Wiring Example

QS smart

power panel

To DALI link 2To DALI link 1

GRAFIK Eye QS

with DALI

LUTRON

LUTRONLUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

5.26

4.263.75

2.50

1.06

LUTRON

LUTRONLUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

LUTRONLUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 7

For additional information, see the complete installation and operation guide at www.lutron.com/qs

Completing Installation of the GRAFIK Eye® QS with DALI

1. Mount the control unit in the wallbox as

shown using the four screws pro vid ed.

Note: Follow all local and national

electrical codes when installing PELV

(Class 2: USA) wiring with line voltage/

mains wiring.

2. Verify installation:

• Restore power.

• Press the top scene button. The LED will

light.

•

Press the zone raise or lower button.

Make sure the control unit is dimming all

connected loads.

3. Apply the protective overlay to the control

unit. See the complete installation and

operation guide at www.lutron.com for

instructions for naming zones.

Note: When tightening mounting

screws, make sure that the hinged

cover and faceplate will open fully,

as shown.

Wall

7,9 in

(200 mm)

3,5 in

(87 mm)

3,75 in

(95 mm)

Protective overlay

(apply after installation)

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 8

For additional information, see the complete installation and operation guide at www.lutron.com/qs

Entering and Exiting Programming Mode

To enter programming mode:

Press and hold the top and bottom scene

buttons simultaneously for 3 seconds. The

LEDs in the scene buttons will scroll from

top to bottom, confirming that you are in

programming mode, and the info screen will

display the main menu.

To exit programming mode:

Press and hold the top and bottom scene

buttons simultaneously for 3 seconds. The

info screen will go to Scene 1.

Navigating Menus in Programming Mode

Master Buttons

The Master buttons allow you to move through the menu

choices. The current choice is highlighted on the info screen.

OK Button

The OK button chooses the current highlighted menu choice.

This will either take you to the next menu or accept a setting you

have selected. When the screen displays a Yes/No question, the

OK button is “Yes”.

Timeclock Button

The timeclock button functions as a “back” button during

programming mode. Pressing the timeclock button takes you

back one step in the current menu. Pressing it repeatedly

will eventually return you to the main menu, but will not exit

programming mode. When the screen displays a Yes/No

question, the Timeclock button is “No”.

Programming Mode

OK

1 2

3

4

5

69 10

11 12

13

14

7

815

16

9-16

1-8

Press and hold the top and

bottom buttons for 3 seconds

to enter or exit programming

mode

Master buttons

OK button

Timeclock (back) button

Main menu

Scene setup

Timeclock

Scene 1

Fade time

3 seconds

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 9

For additional information, see the complete installation and operation guide at www.lutron.com/qs

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 10

For additional information, see the complete installation and operation guide at www.lutron.com/qs

Wireless Mode

Many models of the GRAFIK Eye® QS support wireless communication with other

Lutron products. This feature allows for easy integration of wireless sensors, keypads,

remotes, and window treatments for single-room wireless applications, as well as

compatibility with other Lutron wireless systems.

Units supporting wireless communication have model numbers beginning with QSGRJ,

QSGRK, or QSGRM.

The wireless feature of the GRAFIK Eye QS Wireless control unit has three (3) modes of

operation.

• Disabled: Use for wired-only systems.

• Enabled: The GRAFIK Eye QS Wireless control unit will respond to any programming

commands from nearby Lutron QS wireless (and compatible) products.

• Ignore Programming (default): The GRAFIK Eye QS Wireless control unit will only

respond to normal operation commands from wireless devices programmed while in

Enabled mode.

To change the wireless mode of the GRAFIK Eye QS wireless control unit:

1. Enter programming mode (see page 9).

2. Use the Master buttons to highlight “Wireless Mode” and press

the OK button to accept.

3. Use the Master buttons to highlight the desired wireless mode,

and press the OK button to accept.

4. The info screen will display a confirming “Saved” message.

5. Exit programming mode (see page 9).

Notes

• The wireless signal has a range of 10 m (30 feet) through

standard construction.

Wireless Mode

Enabled

Saved

Main menu

Shade labels

Wireless Mode

OK

1 2

3

4

5

69 10

11 12

13

14

7

815

16

9-16

1-8

Master

buttons

OK

button

Timeclock

(back) button

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 11

For additional information, see the complete installation and operation guide at www.lutron.com/qs

Assign Load Types

Load types supported by the GRAFIK Eye® QS with DALI:

• Digital load

• DMX

• RGB/CMY DMX

• Non-dim digital

Note: For all DMX or RGB/CMY DMX lighting, an external

DMX interface (such as the QSE-CI-DMX) must be

used with the control unit.

1. Enter programming mode (see page

9).

2. Use the Master buttons to highlight

“Zone setup” and press the

OK button to accept.

3. Use the Master buttons to highlight

“Load type”. Press the OK button to

accept.

4. Use the zone raise/lower buttons to

choose the load type for that zone.

Press the OK button to accept.

5. The info screen will confirm that your

load type has been saved.

6. Exit programming mode (see page 9).

Zone Setup

OK

1 2

3

4

5

69 10

11 12

13

14

7

815

16

9-16

1-8

Master

buttons

OK button

Main menu

CCI Mode

Zone setup

OK

1 2

3

4

5

69 10

11 12

13

14

7

815 16

9-16

1-8

Use the

zone

raise/lower

buttons to

choose the

load type for

that zone.

Zone Setup

Non-Dim Load Type

Load Type

Set zones

Saved

Load Type

Assign Non-Dim Load Type

Zones assigned to non-dim loads have three available configurations:

• LOFO: Last On, First Off

• FOFO: First On, First Off

• FOLO: First On, Last Off

Scenes made up of both dim and non-dim

load types will toggle the non-dim loads

before the dim loads in a “First” on/off

configuration, and after the dim loads in a

“Last” on/off configuration.

1. Enter programming mode (see page 9).

2. Use the Master buttons to highlight “Zone

setup” and press the OK button to accept.

3. Use the Master buttons to highlight “Non-Dim

Load type”. Press the OK button to accept.

4. Use the zone raise/lower buttons to choose

the non-dim load type for that zone. (Zones

not programmed as non-dim will be displayed

as Unaffected.) Press the OK button to

accept.

5. The info screen will confirm that your load

type has been saved.

6. Exit programming mode (see page 9).

Main menu

CCI Mode

Zone setup

Zone Setup

Load Type

Set zones

Saved

Non-Dim Load Type

DALI Setup Overview

After DALI devices are wired and powered, they must be reset and addressed so the

system can control them. The “Build System” command automates this process, as

shown below.

Note: All existing DALI programming will be deleted when the “Build System”

command is run.

Build System

1. Enter programming mode (see page 9).

2. Use the Master buttons to highlight “DALI” and press the

OK button to accept.

3. Use the Master buttons to highlight “Build system” and press

the OK button to accept.

4. Press the OK button to erase all current programming, reset

and address DALI devices, and find sensors on the system.

5. Exit programming mode (see page 9).

Note: After running “Build System”, Zone 4 will control all DALI

devices for diagnostics and verification of wiring. (This feature

is disabled once any of the addressed devices are assigned

to a zone on the GRAFIK Eye QS.) Use the Zone 4 raise/lower

buttons to verify that all devices are correctly addressed. If a

device does not respond, repeat the “Build System” command

and/or check the wiring.

Main menu

Zone setup

DALI

Assign zones

Build system

Erase digital load

Programming?

Build system

DALI

OK

1 2

3

4

5

69 10

11 12

13

14

7

815 16

9-16

1-8

Use Zone 4

raise/lower

buttons

to verify

all DALI

devices

have been

addressed.

Searching...

x

Found

x Loads

Found

OK

1 2

3

4

5

69 10

11 12

13

14

7

815

16

9-16

1-8

Master

buttons

OK

button

Timeclock

(back) button

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 12

For additional information, see the complete installation and operation guide at www.lutron.com/qs

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 13

For additional information, see the complete installation and operation guide at www.lutron.com/qs

DALI Setup

Assign/Unassign a DALI Device to a Zone (Zone setup)

DALI devices must be addressed on the system (see previous page) before assigning

or unassigning to a zone.

1. Enter programming mode (see page 9).

2. Use the Master buttons to highlight “DALI” and press the OK

button to accept.

3. Use the Master buttons to highlight “Assign zones” and press

the OK button to accept.

4. Use the Master buttons to scroll through the DALI devices on

the link. The selected device will flash, and the info screen

will display the device number and the number of devices on

the link. If the device is currently assigned to a zone, the zone

number will display at the bottom of the screen and the LEDs

for the zone will go on; otherwise, the info screen will display

“*Unassigned*”.

• Press the zone raise button to assign the device to that

zone.

• Press the zone lower button to unassign the device to that

zone.

5. Press the timeclock (back) button to return to the DALI menu.

DALI devices will return to normal levels.

6. Exit programming mode (see page 9).

Notes

Devices that were previously assigned to a zone will be

removed from the old zone and assigned to the new zone

(each device can be assigned to only 1 zone at a time).

Devices can be assigned only to zones set to DALI load type.

Refer to page 11 for instructions on changing load type.

OK

1 2

3

4

5

69 10

11 12

13

14

7

815 16

9-16

1-8

Use the

zone raise

or lower

button to

assign or

unassign

a DALI

device to

that zone.

Zone LEDs

Main menu

Zone setup

DALI

Address All

Assign zones

Ballast 2 / 23

Zone 3

DALI

Assign zones

Ballast 2 / 23

*Unassigned*

OK

1 2

3

4

5

69 10

11 12

13

14

7

815

16

9-16

1-8

Master

buttons

OK

button

Timeclock

(back) button

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 14

For additional information, see the complete installation and operation guide at www.lutron.com/qs

OK

1 2 3 4 5 6

Wireless Occupancy Sensor

“Talks” to GRAFIK Eye QS control

unit, activating scenes on the

GRAFIK Eye QS.

Lutron’s wireless Radio Powr SavrTM occupancy and vacancy sensors can

be associated with the GRAFIK Eye QS Wireless to activate scenes when

occupancy or vacancy is detected.

This section applies to installations where the GRAFIK Eye QS Wireless is

being used in a single-room wireless installation.

To associate wireless occupancy sensors and GRAFIK Eye QS control units:

1. Make sure the wireless mode of the GRAFIK Eye QS control unit is

“Enabled” (see page 10).

2. Press and hold the “Lights On” and “Lights Off” buttons on the front of

the occupancy/vacancy sensor simultaneously until the lens starts flashing

(about 3 seconds). The info screen on the GRAFIK Eye QS will display

“Occ Sensor Programming.”

3. Press and hold the top scene button of the GRAFIK Eye QS Wireless

control unit until the LEDs flash (about 3 seconds).

4. Return to the occupancy sensor. Press and hold the “Lights On” and

“Lights Off” buttons simultaneously until the lens stops flashing (about 3

seconds).

5. Test communication between the devices using the “Lights On” and “Lights

Off” buttons.

To disassociate wireless occupancy sensors and GRAFIK Eye control units:

Simply repeat the association steps, in the same order; press and hold the

bottom scene button on the GRAFIK Eye QS to disassociate.

Note: The wireless signal has a range of 10 m (30 feet) through standard

construction.

Associating Wireless Occupancy Sensors and GRAFIK Eye® QS Wireless Control Units

(for wireless enabled units only)

On the wireless occupancy

sensor, press and hold the

“Lights On” and “Lights Off”

buttons for 3 seconds to

begin or end association

or disassociation with the

GRAFIK Eye QS control unit.

Note: Pressing the “Lights

On” button initiates the

“occupied” action on the

GRAFIK Eye QS control

unit. Pressing the “Lights

Off” button initiates the

“unoccupied” action.

OK

1 2

3

4

5

69 10

11 12

13

14

7

815 16

9-16

1-8

On the GRAFIK Eye QS control unit,

press and hold the top scene button

for 3 seconds to associate, or press

and hold the bottom scene button for

3 seconds to disassociate with the

occupancy sensor.

Associate

OR

Disassociate

GRAFIK Eye QS Control Unit

“Listens” to wireless occupancy sensor,

so that the occupancy sensor activates

scenes on the GRAFIK Eye QS.

Lens

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 15

For additional information, see the complete installation and operation guide at www.lutron.com/qs

Occupancy Sensor Setup

Scene Mode

This step allows you to assign occupied and unoccupied scenes to up to four

occupancy sensors connected to the GRAFIK Eye® QS control unit.

Select Sensors

1. If not already done, select “Scene Mode” from the

Occupancy Sensor Setup menu.

2. Use the Master buttons to highlight “Setup” and press the

OK button to accept. The screen will display “Searching” while

the unit detects available occupancy sensors.

3. Use the Master buttons to scroll through the list of available

occupancy sensors. When the desired sensor is displayed,

press the OK button to select it. Then choose “Assign” or

“Unassign” from the following menu and press OK. A screen

will verify your choice has been completed. Repeat for

additional sensors.

Set Sensor Action

4. Press the Back button to return to the Occ Sensor screen.

Use the Master buttons to highlight “Actions” and press the

OK button to accept. By default, the occupied scene is set to

“No Action” and the unoccupied scene is set to “Scene Off”.

5. Use the Master buttons to highlight the scene you wish to

use for occupied status and press the OK button to accept.

Repeat for the scene you wish to use for unoccupied status.

Press the OK button to accept.

6. Exit programming mode (see page 9).

Note: If wireless sensors are not found, verify that they are

associated correctly (see page 14).

Saved

3 seconds

Occ Sensor

Setup

Actions

Occupied Scene

Scene 1

Unoccupied Scene

Scene Off

Occ Sensor

Labels

Setup

Sensor x/y

SN: xxxx-xxxx

Source: RF 1/n

Assignment

Unassign

Assign

Saved

*Assigned*

Saved

Searching

OK

1 2

3

4

5

69 10

11 12

13

14

7

815

16

9-16

1-8

Master

buttons

OK

button

Timeclock

(back) button

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 16

For additional information, see the complete installation and operation guide at www.lutron.com/qs

Lutron’s wireless Radio Powr SavrTM daylight sensors can be associated with the

GRAFIK Eye QS Wireless to adjust light levels when certain daylight levels are detected.

This section applies to installations where the GRAFIK Eye QS Wireless is being used in

a single-room wireless installation.

To associate wireless daylight sensors and GRAFIK Eye QS Wireless control units:

1. Make sure the wireless mode of the GRAFIK Eye QS control unit

is “Enabled” (see page 10).

Note: To properly save the wireless mode, exit and then re-enter

programming mode before associating wireless daylight

sensors.

2. Enter programming mode (see page 9).

3. Use the Master buttons to highlight “Sensor setup” and press

the OK button to accept.

4. Use the Master buttons to highlight “Add wireless sensors” and

press the OK button to accept.

5. Press and hold the “Link” button on the front of the daylight

sensor until the sensor starts flashing. The info screen on the

GRAFIK Eye QS will display the sensor’s serial number.

6. Press the OK button on the GRAFIK Eye QS control unit. A

screen will confirm that the sensor has been assigned.

7. Repeat the above steps for all desired sensors.

8. Exit programming mode (see page 9).

To disassociate wireless daylight sensors and GRAFIK Eye QS

control units:

Refer to the Radio Powr Savr daylight sensor install guide to return

the sensor to its “out-of-box” functionality . Doing so will remove

its programming from the GRAFIK Eye QS control unit.

Note: The wireless signal has a range of 10 m (30 feet) through

standard construction.

Associating Wireless Daylight Sensors and GRAFIK Eye® QS Wireless Control Units

(for wireless enabled units only)

OK

1 2

3

4

5

69 10

11 12

13

14

7

815

16

9-16

1-8

Master

buttons

OK

button

Timeclock

(back) button

Main menu

Zone Setup

Sensor Setup

Daylight

SN: xxxx-xxxx:

press OK to Save

Add wireless sen

Initiate association

of sensors

Saved

*Assigned*

Sensor Setup

Daylight

Add wireless sensors

Link

button

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 17

For additional information, see the complete installation and operation guide at www.lutron.com/qs

Daylight Sensor Setup

Mode Assignment

This step allows you to assign daylight sensors on the QS link or connected to the

GRAFIK Eye® QS control unit. Sensors can be assigned in either Zone Mode or Group

Mode.

Zone Mode (default) is useful when the GRAFIK Eye QS is controlling lights in multiple

rooms or areas. Zone mode allows each zone to adjust its “outputted” light level based

on measured daylight levels. Only one sensor can be assigned to each zone (a sensor

can be assigned to more than one zone). Each zone can have a unique target light

level.

Group Mode is useful when groups or rows of lights for daylighting go across multiple

zones. A group can consist of any combination of DALI loads in the system. Each

group can be assigned to only one sensor (a sensor can be “shared by” more than one

group). Each group can have a unique target light level.

1. Enter programming mode (see page 9).

2. Use the Master buttons to highlight “Sensor setup” and press

the OK button to accept.

3. Use the Master buttons to highlight “Daylight” and press the

OK button to accept.

4. Use the Master buttons to highlight “Mode” and press the

OK button to accept.

5. Use the Master buttons to highlight “Zone Mode” to assign

sensors to zones, or “Group Mode” to assign sensors to a group

of DALI loads. Press the OK button to accept. A screen will

confirm your selected mode has been saved and you will return

to the Daylight Sensor screen.

To configure Zone Mode, see page 18. To configure Group

Mode, see page 19.

Note: Changing modes will remove all previous daylight

assignments.

OK

1 2

3

4

5

69 10

11 12

13

14

7

815

16

9-16

1-8

Master

buttons

OK

button

Timeclock

(back) button

Main menu

Zone Setup

Sensor Setup

Daylight Sensor

Zone Mode

Daylight Sensor

Setup

Mode

Saved

Daylight Sensor

Group Mode

OR

Sensor Setup

Occupancy

Daylight

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 18

For additional information, see the complete installation and operation guide at www.lutron.com/qs

Daylight Sensor Setup

Zone Mode

This step allows you to assign sensors to each zone, with one daylight sensor per

zone connected to the GRAFIK Eye® QS control unit. Sensors can be assigned to

more than one zone.

Select Sensors

1. If not already done, complete the steps on page 17, and

select “Zone Mode”.

2. Use the Master buttons to highlight “Setup” and press the

OK button to accept. Available sensors will be displayed.

3. You can assign one sensor per zone, and a sensor can be

assigned to more than one zone. Use the Master buttons to

scroll through the sensors until the one you wish to assign or

unassign is highlighted, and press the OK button to select it.

4. Use the zone raise and lower buttons for each zone to assign

or unassign the sensor to that zone. The zone raise button

assigns the displayed sensor, and the zone lower button

unassigns it. Repeat for all desired sensors and press OK. A

screen will verify your settings have been saved.

5. Calibrate sensors: Press the Timeclock (back) button to return

to the Daylight Sensor screen. Use the Master buttons to

select the desired group and press the OK button to accept.

6. Use the Master buttons to select the desired zone and press

the OK button to accept.

7. Put any wireless Radio Powr SavrTM daylight sensors

associated with the desired zones into Calibrate Mode: Press

and hold the “Cal” button for 6 seconds until the sensor

flashes.

8. Use the Master buttons to select the desired light level for the

zone, and press the OK button to accept. Repeat for all zone

levels you wish to calibrate. Press the OK button to accept.

9. Exit programming mode (see page 9).

Note: If wireless sensors are not found, verify that they are

associated correctly (see page 16).

Sensor x/y

Select

Zones

OK

1 2

3

4

5

6

9 10

11 12

13

14

7

815 16

9-16

1-8

OK

1 2

3

4

5

69 10

11 12

13

14

7

815 16

9-16

1-8

Zone raise

Zone lower

Daylight Sensor

Calibrate

Setup

Sensor x/y

SN: xxxx-xxxx:

Source: RF

Saved

3 seconds

Daylight Sensor

Setup

Calibrate

Saved

Searching

OK

1 2

3

4

5

69 10

11 12

13

14

7

815

16

9-16

1-8

Master

buttons

OK

button

Timeclock

(back) button

Sensor Name

Zone 1

Adjust Light

More light

Less light

Cal

button

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 19

For additional information, see the complete installation and operation guide at www.lutron.com/qs

Daylight Sensor Setup

Group Mode

This step allows you to assign daylight sensors to a group of DALI loads connected

to the GRAFIK Eye® QS control unit.

Set Up Groups

1. If not already done, complete the steps on page 17, and

select “Group Mode”.

2. Use the Master buttons to highlight “Daylight Groups” and

press the OK button to accept.

3. Use the Master buttons to scroll through the list of available

daylight groups. Up to 16 groups of DALI loads can be

defined. Press the OK button to accept.

4. Use the Master buttons to scroll through the DALI devices on

the link. Press the OK button to add or remove the selected

device. The currently selected device will display its current

assignment status:

Unassigned if it is not assigned to any group

Assigned if it is assigned to the selected (displayed) group

Group x if it is currently assigned to another group (x = the

group number it is assigned to)

5. Press the Timeclock (back) button to return to the list of

configurable groups, and repeat these steps to assign devices

to other groups.

Note: Each DALI device can be assigned to only one group.

Assigning a device already associated with another group will

replace its existing programming.

(continued on next page)

Daylight Sensor

Setup

Daylight Groups

Group 1

Ballast 2/23

*Unassigned*

OK

1 2

3

4

5

69 10

11 12

13

14

7

815

16

9-16

1-8

Master

buttons

OK

button

Timeclock

(back) button

Configure Groups

Group 1

Ballast 2/23

*Assigned*

OR

Group 1

Ballast 2/23

*Group 2*

OR

®

GRAFIK Eye® QS with DALI Quick Installation and Operation Guide 20

For additional information, see the complete installation and operation guide at www.lutron.com/qs

Daylight Sensor Setup

Group Mode (continued)

Select Sensors

1. Press the Timeclock (back) button to return to the Daylight

Sensor menu.

2. Use the Master buttons to highlight “Setup” and press the

OK button to accept.

3. Use the Master buttons to scroll through the list of available

daylight sensors. When the desired sensor is displayed, press

the OK button to select it.

4. Use the Master buttons to scroll through the list of available

groups. When the desired group is displayed, press OK

to assign or unassign the sensor to that group. Press the

Timeclock (back) button to return to the list of available

sensors and repeat for additional sensors.

5. Calibrate sensors: Press the Timeclock (back) button to return

to the Daylight Sensor screen. Use the Master buttons to

select the desired group and press the OK button to accept.

6. Use the Master buttons to select the desired group and press

the OK button to accept.

7. Put any wireless Radio Powr SavrTM daylight sensors

associated with the desired groups into Calibrate Mode:

Press and hold the “Cal” button for 6 seconds until the sensor

flashes.

8. Use the Master buttons to select the desired light level for

the group, and press the OK button to accept. Repeat for all

group levels you wish to calibrate. Press the OK button to

accept.

9. Exit programming mode (see page 9).

Note: If wireless sensors are not found, verify that they are

associated correctly (see page 16).

Daylight Sensor

Calibrate

Setup

Sensor x/y

SN: xxxx-xxxx

Source: RF

OK

1 2

3

4

5

69 10

11 12

13

14

7

815

16

9-16

1-8

Master

buttons

OK

button

Timeclock

(back) button

Saved

3 seconds

Daylight Sensor

Setup

Calibrate

Group 1

Sensor x

Group 1

*Unassigned*

Sensor x

Group 1

*Assigned*

Adjust Light

More light

Less light

Cal

button

La pagina sta caricando ...

Lutron Electronics QSGRM-16D Quick Installation And Operation Manual

Questo manuale è adatto anche per

Lutron Electronics QSGRM-16D Quick Installation And Operation Manual

in altre lingue

Documenti correlati

Altri documenti