American Standard P2969SWT.375 Guida d'installazione

American Standard
Marca
American Standard
Modello
P2969SWT.375
Tipo
Guida d'installazione
755796-100 (5/19)-1-
Product names listed herein are trademarks of AS America Inc.
© AS America Inc. 2019
INSTALLATION INSTRUCTIONS
Passage
™
Shower Wall Tile Collection
Nominal Dimensions: 60 x 32 x 72
Model: P2969SWT
Visit http://www.americanstandard-us.com/passage-collection for coordinating products.
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years.
To ensure this product is installed properly, please read these instructions carefully before you begin.
Certain installations may require professional help.
American Standard Passage Shower Walls are designed to be installed together with the American Standard Passage
Shower Base.
If your specific installation does not include a Passage Shower Base, you will need to adjust the width of your
shower alcove to 59-1/4"
(1505 mm) to ensure correct fit with installed substrate. (see Illustration 1)
REQUIRED TOOLS AND MATERIALS
TOOLS:
Tape Measure Drill
Caulking Gun Level
Masking Tape Square
Hole Saw Pencil
Jig Saw with fine tooth blade
MATERIALS:
Suction Cups - optional
SOLD SEPARATELY:
x8 Tubes Waterproof Instant Grab
Construction Adhesive
x2 Tubes Tub & Tile Sealant
BEFORE YOU BEGIN....
Local building codes vary by location. Observe all local plumbing and building codes.
Unpack your new shower walls and inspect them carefully for damage. Verify that the walls are the correct size for your installation.
NOTE: Take extra care in handling the front surfaces of the walls. Use only non-abrasive cloths to avoid scratching.
STEP 1: PREPARATION
Do not install directly to studs.
Passage Shower Walls must be installed over a solid, water resistant substrate such as greenboard.
If alcove opening is larger than rough-in opening (see Illustration 1) there will be a visible gap between
rear corners. Fir-out studding if necessary before installing substrate to provide correct alcove opening for
panels. Ensure alcove is plumb and square.
1) ROUGH PLUMBING & FITTINGS MUST
BE INSTALLED BEFORE WALLS
2) WALL SURFACE PREPARATION
Ensure wall surface is dry, smooth, and free of dust, soap
scum, mold or other contaminants. Wipe wall surfaces
with a damp cloth and allow to dry.
TIP: Priming wall substrate improves shower
wall adhesion. Wall surface must be dry before
panels can be applied.
NOTE: IF YOU PLAN TO INSTALL A SHOWER DOOR
Follow manufacturer’s instructions and prepare
stud wall accordingly.
Illustration 1
SAVE FOR FUTURE USE
59-1/4" (1505mm)
755796-100 (5/19)-2-
STEP 2: INSTALLING REAR WALL PANELS
1) Starting with the bottom rear panel, dry fit bottom to top
with the exposed Lap Joint facing you. Keep a 1/8" (3mm)
gap above shower base. (Illustration 2)
Hold rear panel in place and mark a horizontal line across
top edge of rear panel. Trim rear panels if needed to fit
within alcove area.
Trimming Panels:
a) Measure shower enclosure.
b) Apply masking tape to approximate cut area on the tile
finished side to prevent chipping and protect surface.
c) Transfer measurement to panel.
d) Using a jigsaw with a fine tooth blade, cut along line on
finished tile side. Ensure a new blade is used.
NOTE: Install one panel at a time.
2) Wipe all panels and walls with a damp cloth to remove any
dust or debris and allow to fully dry.
3) Starting with the bottom rear back panel first, apply 1/4"
(6mm) bead of adhesive on the substrate in evenly spaced
vertical strips every 6" (152mm) for each panel top to
bottom. (Illustration 3)
Apply one row of adhesive horizontally to the top and
bottom edges of the substrate. (Illustration 3) Also apply
waterproof construction adhesive to the Lap Joint of both
bottom and top panels. (Illustration 2)
Wipe off excess adhesive with a water dampened rag.
4) Move bottom rear panel onto the wall keeping a space of
approximately 1/8" (3mm) off the surface of the shower
base. Press panel firmly over entire surface to ensure firm
contact of panel to adhesive on wall.
5) Place top rear panel in place on rear wall as in steps above.
TIP: Suction cups will aid in the handling and
installation of the shower wall panels.
SHOWER BASE
TOP
SHOWER
SIDE
SUBSTRATE
SIDE
TOP
LAP
JOINT
BOTTOM
LAP
JOINT
1/8" (3mm)
Spacing Above
Shower Base
Illustration 2
Illustration 3
755796-100 (5/19)-3-
STEP 5: APPLYING SEALANT FOR SEAMS AND JOINTS
1) Once all panels are securely in place and set, apply the
tub and tile sealant to all corners, seams between panels
and gaps between bottom panels and shower base.
(Illustration 6)
NOTE: Wipe any excess adhesive from the panel
with water dampened rag.
Allow 24 hours for the sealant to dry before use.
Illustration 6
STEP 3: INSTALLING SIDE WALL PANELS
1) Orient side panel to match subway tile design
of top rear panel.
2) Align grout lines of side panels with rear wall panel
grout lines. Trim side panels if needed to fit within alcove
area. (Illustration 4)
Trim or cut from bottom edge of side panels so that the
top edge of the panels are level with the top edge of
the back panels.
Tri mming Panels:
a) Measure shower enclosure.
b) Apply masking tape to approximate cut area on the tile
finished side to prevent chipping and protect surface.
c) Transfer measurement to panel.
d) Using a jigsaw with a fine tooth blade, cut along line on
finished tile side. Ensure a new blade is used.
3) Once both side panels are properly dry fitted, mark all
panels and trim as needed:
a) Apply tape to approximate location
b) Mark all plumbing locations
c) Drill holes at each location using hole saws large enough
to accomomdate the opening but small enough to be
covered by the trim plates. (Illustration 5)
NOTE: Drill from nished tile side.
Do not use wood/paddle bits or grit hole saws as
they will chip.
4) Wipe panels and walls with a damp cloth to remove any
dust or debris. Allow to fully dry.
5) Apply 1/4" (6mm) bead of adhesive on the substrate in
evenly spaced vertical strips every 6" (152mm) for each
panel, top to bottom. (Illustration 3) Apply one row of
adhesive horizontally to the top and bottom edges of the
substrate. (Illustration 3) Wipe off excess adhesive with
a water dampened rag.
6) Repeat on second wall panel.
SHOWER VALVE
Illustration 4
Illustration 5
CORRECT
PANEL POSITION
TOP REAR PANEL
RIGHT SIDE PANEL
TOP REAR PANEL
RIGHT SIDE PANEL
REAR CORNER
INCORRECT
PANEL POSITION
REAR CORNER
GROUT
LINES
755796-100 (5/19)-4-
AFTERCARE AND CLEANING
AS AMERICA, INC. 10 YEAR LIMITED WARRANTY FOR PASSAGE BATH WALLS
WARNING: Cleaning products with labels that say “not suitable for use with ABS, acrylic or polystyrene”
SHOULD NOT BE USED. Read all labels carefully.
• Clean shower walls with warm soapy water and soft sponge. For stubborn stains, use a 50/50 mix of isopropyl alcohol and water.
• HARSH CHEMICALS SHOULD NEVER BE USED ON SHOWER WALL SURFACE. Clean after use with a mild
liquid household detergent cleaner. Do not use Lestoil
®
, Lysol
®
Disinfectant (spray or concentrate), or Lysol
®
Basin,
Tub and Tile Cleaner, Windex
®
, Mr. Clean
®
, Dow
®
Disinfectant Bathroom Cleaner, or cleaning products in aerosol cans.
• Do not use wire brushes, knives or sharp objects to remove stains, or other surface blemishes.
• Abrasive cleaners or powders should not be used as they will dull the surface.
• Do not allow nail polish remover, acetone, paint remover or other solvents to come into contact
with the surface.
AS America, Inc. (“American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this
these walls or any of its parts that are found by American Standard, in its sole judgment, to be defective under normal residential
use and maintenance so long as it is owned by the original consumer purchaser.
To activate this limited warranty, the purchaser must go online to our website at www.americanstandard-us.com/warranty to
register their bath walls within thirty (30) days of purchase.
In no event will American Standard be liable for the cost of repair or replacement of any installation materials including but not
limited to tiles, marble etc.
This limited warranty DOES NOT COVER the following:
1. Defects or damages arising from shipping, installation, alterations, accidents, abuse, misuse, lack of proper maintenance and
cleaning as directed in the owner’s manual and use of other than genuine American Standard replacement parts, in all cases
whether caused by a plumbing contractor, service company, the owner or any other person.
2. Deterioration through normal wear and tear and the expense of normal maintenance.
3. Commercial application.
4. Options and accessories. American Standard’s limited warranty on these items is one year for parts only and excludes labor.
This one year limited warranty covers accessories manufactured by American Standard (e.g. aprons, drains, grab bars, heaters,
trim kits) against defects of material or workmanship. Warranty coverage begins on the date the accessory was originally
purchased by the owner.
5. Postage or shipping costs for returning products for repairs or replacement under this limited warranty and labor or other
costs incurred in connection with product removal or installation under this limited warranty.
6. ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, ALL OF WHICH ARE HEREBY EXPRESSLY DISCLAIMED,
OR THE EXTENSION BEYOND THE DURATION OF THIS LIMITED WARRANTY OF ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY OR FITNESS FOR AN INTENDED PURPOSE. (Some jurisdictions do not allow limitations on
how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so these limitations
and exclusions may not apply to you.)
7. Responsibility for compliance with local code requirements. (Since local code requirements vary greatly distributors, retailers,
dealers, installation contractors and users of plumbing products should determine whether there are any code restrictions
on the installation or use of a specific product.)
This warranty gives you specific legal rights. You may have other legal rights that vary from state to state. For service under this
warranty, you should contact the following:
In the United States:
American Standard Brands
1 Centennial Ave
Piscataway, New Jersey 08854
Attention: Director of Consumer Affairs
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: (800) 442-1902
www.americanstandard.com
In Canada:
LIXIL Canada ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: (800) 387-0369
www.americanstandard.ca
In Mexico:
American Standard B&K Mexico
S. de R.L. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Toll Free: 01-800-839-1200
www.americanstandard.com.mx
POST INSTALLATION
Remove all construction debris. Install any accessories, shelves or doors according to manufacturer's installation instructions.
Post installation clean-up can be completed using 50/50 mixture of isopropyl alcohol and water.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

American Standard P2969SWT.375 Guida d'installazione

American Standard
Marca
American Standard
Modello
P2969SWT.375
Tipo
Guida d'installazione
Scarica il pdf
rapporto

in altre lingue

Altri documenti