Pella 808SQ102 Manuale utente

Marca: Pella

Modello: 808SQ102

Tipo: Manuale utente

INSTALLATION INSTRUCTIONS -

INSTRUCCIONES DE INSTALACIÓN

CLAD SLIDING PATIO DOOR - SOUTHWESTERN WALL WITH HARD

COAT STUCCO

PUERTA PARA PATIO CORREDIZA, PARA PARED ESTILO SUREÑO

CON ESTUCO DE CAPA BASE

Installation Instructions for Typical Wood Frame Construction.

These instructions were developed and tested for use with typical wood frame wall construction in a wall system designed to manage water.

These instructions are not to be used with any other construction method. Installation instructions for use with other construction methods,

multiple units or bow and bay windows, may be obtained from Pella

Corporation or a local Pella retailer. Building designs, construction methods,

building materials, and site conditions unique to your project may require an installation method different from these instructions and additional

care. Determining the appropriate installation method is the responsibility of you, your architect, or construction professional.

YOU WILL NEED TO SUPPLY:

• Cedar or Impervious shims/spacers (12 to 20)

• 2" galvanized rooﬁng nails (1/4 lb.)

• Closed cell foam backer rod/sealant backer (12 to 30 ft.)

• Pella

SmartFlash

™

foil backed butyl window and door

ﬂashing tape or equivalent

• High quality exterior grade polyurethane or silicone sealant

(2 to 3 tubes per door)

• Great Stuff

™

Window and Door Insulating Foam Sealant

by the Dow Chemical Company or equivalent low pressure

polyurethane window and door foam - DO NOT use high

pressure or latex foams.

• Pella aluminum sill support or 2 x 4 wood blocking

• Interior trim and/or jamb extensions (15 to 40 ft.)

• 9" wide Fortiﬁber ﬂashing paper or equivalent

TOOLS REQUIRED:

• Tape measure

• 6' Level

• Square

• Hammer

• Stapler

• Sealant gun

• Scissors or utility knife

• Drill

• Screwdrivers

(#2 Phillips with 8" shaft and small ﬂat blade)

Always read the Pella

Limited Warranty before purchasing or installing Pella products. By installing this product, you are acknowledging

that this Limited Warranty is part of the terms of the sale. Failure to comply with all Pella installation and maintenance instructions may void your Pella product

warranty. See Limited Warranty for complete details at http://warranty.pella.com.

REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.



'MBTIJOH1BQFS

4JMM'MBTIJOH5BQF

4JMM'MBTIJOH5BQF

/BJMJOH'JO

4JMM4VQQPSU

5PQ

'MBTIJOH

5BQF

'JO

$PSOFS

4JEF

'MBTIJOH

5BQF

*OUFSMPDLFS

4JEF

'MBTIJOH

5BQF

XJEF'MBTIJOHQBQFS

4&"-"/5

Part Number: 808S0102

Lea las instrucciones en español en el reverso.

1 ROUGH OPENING PREPARATION

A. Conﬁrm the opening is plumb and level.

Note: It is critical that the bottom is level.

B. Conﬁrm the door will ﬁt the opening. Measure all four sides of the opening to

make sure it is 3/4" larger than the door in width and 1/2" larger in height. Measure

the width at the top, bottom, and center. Measure the height at the far left side, the

far right side, and in the center.

Note: 1-1/2" or more of solid wood blocking is required around the perimeter of

the opening. Fix any problems with the rough opening before proceeding.

C. Apply ﬂashing paper at the bottom (1C). Cut one piece of ﬂashing paper 18" longer

than the width of the rough opening. Position the top edge of the ﬂashing paper with

the top of the sill plate. Center the ﬂashing paper with the opening width. Staple the

ﬂashing paper to the sill plate.

Note: Bottom ﬂashing paper is not required for installation on concrete ﬂoors.

D. Apply ﬂashing paper to the sides of the rough opening (1D). Cut two pieces of

ﬂashing paper 18" longer than the height of the rough opening. Apply one piece to

each jamb. Position the edge of the ﬂashing paper with the inside edge of the trimmer

(jack stud), and center the ﬂashing paper with the height of the rough opening. Staple

the ﬂashing paper to the trimmer.

E. Apply bottom ﬂashing tape #1. Cut a piece of ﬂashing tape 12" longer than the opening

width. Apply at the bottom of the opening as shown (1E) so it overhangs 1" to the exterior.

Note: The tape is cut 12" longer than the width of the opening so that it will extend up

each side approximately 6".

F. Tab the bottom ﬂashing tape and fold. Cut 1" wide tabs at each corner (1/2" from each side

of corner) (1F). Fold tape to the exterior and press ﬁrmly to adhere it to the ﬂashing paper.

G. Apply bottom ﬂashing tape #2. Cut a piece of ﬂashing tape 12" longer than the opening

width. Apply at the bottom, overlapping tape #1 by at least 1". DO NOT allow the tape to

extend past the interior face of the framing (1G).

Note: The ﬂashing tape does not need to extend all the way to the interior of the framing.

H. Attach the aluminum sill support or wood blocking to the exterior of the box plate

to support the edge of the door sill. Place the sill support ﬂush with the subﬂoor.

£

£

£

£







£

£



£

£

2 PREPARE THE DOOR FOR INSTALLATION

A. Remove the plastic wrap and cardboard packaging from the door.

Note: If screens, grilles or hardware are removed from the door at this time, label them and store them in a protected area.

B. Remove the shipping spacers. Carefully slide the movable panel halfway open and remove the spacers from both the top and bottom of the

movable panel.

TWO OR MORE PEOPLE WILL BE REQUIRED TO HANDLE THE PANEL & FRAME SAFELY.

C. Remove the venting panel by lifting it out of the lower track and tilting the bottom of the panel away

from the door frame. Then, lower the panel out of the top track. Carefully set the panel aside.

Note: Assemble the OXXO frame per the instructions included with the door splice kit.

D. Fold out installation ﬁn to 90°. Be careful not to remove or tear the ﬁn corners.

Note: If the ﬁn is not at 90°, the door will not line up correctly on the interior.

3 SETTING AND FASTENING THE DOOR

A. Place three 3/8" beads of sealant. The ﬁrst bead should be approximately 3/4" from the exterior of the rough

opening, the second 2-1/2" in from the ﬁrst bead of sealant. Place a third bead of sealant in the groove of the sill

support or 1/4" from the exterior edge of the wood blocking.

TWO OR MORE PEOPLE WILL BE REQUIRED FOR THE FOLLOWING STEPS.

B. Insert the door from the exterior of the building. DO NOT slide the bottom of the

door into the opening. Sliding will damage the sealant lines. Place the bottom of the

door at the bottom of the opening, then tilt the top into position. Center the door

between the sides of the opening to allow equal clearance for shimming, and insert

one rooﬁng nail in the ﬁrst hole from the corner on each end of the top nailing ﬁn.

These are used to hold the door in place while shimming it plumb and square.

C. Plumb and square door. Insert shims, as necessary, between the door

and the sides of the rough opening starting up 6" from the bottom of

the door.

Note: DO NOT OVER SHIM.

D. Check the interior reveal. Make sure the measurement from the

interior face of the door to the interior face of the wall is equal at

several points around the door.

Note: If the dimensions are not equal, check to make sure the ﬁns

are folded out to 90° at all points.

E. Secure the frame. Insert a 1" wide shim behind the pilot hole at the lock strike(s).

Insert a #8 x 2-1/2" screw (included in the panel retainer and screw package) into the

pilot hole making sure it passes through the shim and into the rough opening.

Note: The weather strip must be pushed aside to reveal the pilot hole. Be careful

not to damage the weather-strip. Architect Series

and Designer Series

have 2

lock strikes, ProLine

has one lock strike.

F. Fasten the door to opening by driving 2" galvanized rooﬁng

nails into each pre-punched hole in the nailing ﬁn.

Note: Make sure the ﬁn corner is lying as ﬂat as possible.

ProLine Doors - Proceed to Step 4.

Ó

Î

Î

&YUFSJPS

Î

*OUFSJPS

Î

Óä Îä

{ä

xä Èä Çä

ÓÎ

 -



Î

TIJN

Î

TIJN

Î

Î

G. Architect Series and Designer Series: Apply sealant and insert a #8 x 2-1/2" screw (provided) into each hole in the bottom of the door frame

(shown above in gold).

3 SETTING AND FASTENING THE DOOR (continued)

H. Architect Series and Designer Series: Position and secure the panel retainer by drilling pilot holes through the remaining holes in the

retainer into the sill support or wood blocking, then apply sealant to the holes and insert a screw into each hole as speciﬁed below.

Aluminum sill support: 9/64" pilot holes, #10 x 3/4" thread cutting screws (provided).

Wood blocking: 1/8" pilot holes, #10 x 2-1/2" ﬂat head wood screws (provided).

Masonry ﬂoor: 3/16" x 1-3/4" concrete screw. Pilot drill per screw manufacturer’s recommendations.

I. Remove the factory installed screws from the retainer and repeat the process.

J. Architect Series and Designer Series: Drill a 3/16" clearance hole at each indentation in the extrusion at the top of the door frame into

the rough opening, stopping when the drill is through the door frame. Apply sealant to each hole, then insert a #8 x 3" stainless steel

screw into each hole.

4 INTEGRATING THE DOOR TO THE BUILDING FELT

Note: The ﬂashing tape must be applied approximately 1/2" onto

the frame cladding at the jambs and head. Pre-folding the tape 1/2"

before removing the paper backing will make it easier to apply the tape

correctly. If the siding is less than 1/2" thick, adjust the dimension of the

fold so the exterior sealant line will cover the exterior edge of the tape.

A. Apply side ﬂashing tape. Cut 2 pieces of ﬂashing tape 4" longer than the

frame height of the door. Apply one piece 1/2" up onto the frame cladding,

over the nailing ﬁn and onto the ﬂashing paper to each side. The tape

should extend 2" above the top of the door and 2” below the bottom of the

door. Press the tape down ﬁrmly while folding down the excess tape at the

top and bottom of the door.

B. Apply top ﬂashing tape. Cut a piece of ﬂashing tape long enough to go across the top of

the door and extend at least 1" past the side ﬂashing tape on both sides. Apply the tape 1/2"

up onto the frame cladding, over the top nailing ﬁn as shown. Fold the overlapping tape

down, and press all tape down ﬁrmly.

Note: The top ﬂashing tape must overlap the side ﬂashing tape to prevent water from

getting behind it.

C. Apply the top ﬂashing paper. Cut one piece of ﬂashing paper at least 21" longer than

the width of the rough opening. Position the bottom edge of the ﬂashing paper ﬂush with

the frame of the door and center the ﬂashing paper with the width of the door. Staple the

ﬂashing paper to the header.

Note: When applying the ﬁrst layer of building felt, ensure the sill ﬂashing paper overlaps the

building felt. This will tie the door system into the building water management system.

&YUFSJPS

{

&YUFSJPS

{



{

*OUFSJPS

&YUFSJPS

'JYFE1BOFM

5ISFTIPME

Î

Î

"SDIJUFDU4FSJFTBOE%FTJHOFS4FSJFT

5 REINSTALL THE SLIDING PANEL

TWO OR MORE PEOPLE WILL BE REQUIRED TO HANDLE THE PANEL SAFELY.

x

A. Insert door panel. From the exterior of the building, tilt the top of the panel toward the door frame and

insert the top of the door panel into the top track. Move the bottom of the panel toward the door frame until

it is vertical. Gently set the panel down into the bottom track.

Architect Series: Adjust the panel clip and tighten the panel clip screw.

ProLine only: Install bumpers and the panel retainer. Follow the instructions included in the hardware box.

Note: Be careful not to pinch your ﬁngers between the two panels. DO NOT close the sliding panel until

you have installed the hardware. The door may lock when closed.

B. Install the handles and panel retainer. Follow the instructions included in the hardware box. If the panel is not square to the door frame,

adjust the bottom rollers by removing the adjusting hole cover and inserting an 8" long #2 Phillips screwdriver into the hole. Turn clockwise

to raise the panel and counter-clockwise to lower the panel. Follow the instructions included in the handle box for ﬁnal adjustments.

C. Install screen. Instructions for installing the screen are found in the screen door package.

6 INTERIOR SEAL

Caution: Ensure use of low pressure polyurethane window and door installation foams and strictly follow the foam manufacturer’s

recommendations for application. Use of high pressure foams or improper application of the foam may cause the door to bow and

hinder operation. DO NOT use ﬁberglass insulation.

Interior

A. Apply insulating foam. From the interior, insert the nozzle of the applicator approximately 1" deep

into the space between the door and the rough opening and apply a 1" deep bead of foam. This will

allow room for expansion of the foam and will minimize squeeze out. If using foam other than Great

Stuff

™

Window and Door Insulating Foam Sealant by the Dow Chemical Company, allow the foam

to cure completely (usually 8 to 24 hours) before proceeding to the next step.

Note: DO NOT completely ﬁll the space from the back of the ﬁn to the interior face of the opening.

B. Check the door operation by opening and closing the door.

Note: If the door does not operate correctly, check to make sure it is still plumb, level, square and

that the sides are not bowed. If adjustments are required, remove the foam with a serrated knife.

Adjust the shims, and reapply the insulating foam sealant.

SEALING THE DOOR TO THE

EXTERIOR WALL CLADDING

Note: When applying the casing bead for stucco, leave 1/2" space

between the head of the door and the casing bead, and 3/8" space

between the door jambs and the casing bead for backer rod and

sealant. Refer to the illustration (Southwestern Wall With Stucco).

Note: The sealant details shown are standard recommendations

from the sealant industry. Contact your sealant supplier for

recommendations and instructions for this and any other application.

4065)8&45&3/

8"--

8*5)

456$$0

$MFBSBODF

#BDLFS3PEBOE

4FBMBOUUZQJDBM

*OTVMBUJOH

'PBN

"DDFTTPSZ

(SPPWF



A. Insert backer rod into the space around the door leaving at least a 1/2"

clearance between the backer rod and the exterior face of the casing bead.

Note: Backer rod adds shape and depth for the sealant line.

8 INTERIOR FINISHING

If the products cannot be ﬁnished immediately, cover with clear plastic to protect from dirt, damage and moisture. Remove any construction residue before

ﬁnishing. Sand all wood surfaces lightly with 180 grit or ﬁner sandpaper. DO NOT use steel wool. BE CAREFUL NOT TO SCRATCH THE GLASS.

Remove sanding dust.

Pella products must be ﬁnished per the below instructions; failure to follow these instructions voids the Limited Warranty.

• On casement and awnings, it is optional to paint, stain or ﬁnish the vertical and horizontal sash edges.

• On single-hung and double-hung, do not paint, stain or ﬁnish the vertical sash edges, any ﬁnish on the vertical sash edges may cause the sash to stick; it is

optional to paint, stain or ﬁnish the horizontal sash edges.

• On patio doors, it is optional to paint, stain or ﬁnish the vertical and horizontal panel edges.

Note: To maintain proper product performance do not paint, ﬁnish or remove the weather-stripping, mohair dust pads, gaskets or vinyl parts. Air

and water leakage will result if these parts are removed. After ﬁnishing, allow venting windows and doors to dry completely before closing them.

Pella Corporation is not responsible for interior paint and stain ﬁnish imperfections for any product that is not factory-applied by Pella Corporation. Use

of inappropriate ﬁnishes, solvents, brickwash, or cleaning chemicals will cause adverse reactions with window and door materials and voids the Limited

Warranty.

For additional information on ﬁnishing see the Pella Owner’s Manual or go to www.pella.com.

B. Apply a bead of high quality exterior grade sealant to the

entire perimeter of the door. At each end of the bottom of

the door, insert sealant into the spaces between the bottom

of the door and the sill support and connect it to the

perimeter sealant.

C. Shape, tool and clean excess sealant. When ﬁnished, the

sealant should be the shape of an hourglass.

Note: This method creates a more ﬂexible sealant line

capable of expanding and contracting.

D. Remove plastic guards at the base of the door once

construction is complete.

Ç

Ç

EXTERIOR FINISH

The exterior frame and sash are protected by aluminum cladding with our tough EnduraClad

or EnduraClad Plus baked-on factory ﬁnish that needs no painting.

Clean this surface with mild soap and water. Stubborn stains and deposits may be removed with mineral spirits. DO NOT use abrasives. DO NOT scrape or use

tools that might damage the surface.

Use of inappropriate ﬁnishes, solvents, brickwash or cleaning chemicals will cause adverse reactions with window and door materials and voids the Limited Warranty.

CARE AND MAINTENANCE

Care and maintenance information is available in the Pella Owner’s Manual. You can obtain an owner’s manual by contacting your local Pella retailer. This

information is also available at www.pella.com.

IMPORTANT NOTICE

Because all construction must anticipate some water inﬁltration, it is important that the wall system be designed and constructed to properly manage

moisture. Pella Corporation is not responsible for claims or damages caused by anticipated and unanticipated water inﬁltration; deﬁciencies in building

design, construction and maintenance; failure to install Pella products in accordance with Pella’s installation instructions; or the use of Pella products in wall

systems which do not allow for proper management of moisture within the wall systems. The determination of the suitability of all building components,

including the use of Pella products, as well as the design and installation of ﬂashing and sealing systems are the responsibility of the Buyer or User, the

architect, contractor, installer, or other construction professional and are not the responsibility of Pella.

Pella products should not be used in barrier wall systems which do not allow for proper management of moisture within the wall systems, such as barrier

Exterior Insulation and Finish Systems, (EIFS) (also known as synthetic stucco) or other non-water managed systems. Except in the states of California, New

Mexico, Arizona, Nevada, Utah, and Colorado, Pella makes no warranty of any kind on and assumes no responsibility for Pella windows and doors

installed in barrier wall systems. In the states listed above, the installation of Pella products in barrier wall or similar systems must be in accordance

with Pella’s installation instructions.

Product modiﬁcations that are not approved by Pella Corporation will void the Limited Warranty.

SEALING THE DOOR TO THE

EXTERIOR WALL CLADDING (continued)