Asus RS500A-E12-RS12U Manuale utente

Categoria
Schede madri
Tipo
Manuale utente
1U Rackmount Server
User Guide
RS500A-E12 Series
RS500A-E12-RS12U
ii
Copyright © 2023 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any form or by any means,
except documentation kept by the purchaser for backup purposes, without the express written permission
of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS provides this manual “as is” without warranty of any kind, either express or implied, including but not
limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no
event shall ASUS, its directors, officers, employees, or agents be liable for any indirect, special, incidental,
or consequential damages (including damages for loss of profits, loss of business, loss of use or data,
interruption of business and the like), even if ASUS has been advised of the possibility of such damages
arising from any defect or error in this manual or product.
Specifications and information contained in this manual are furnished for informational use only, and are
subject to change at any time without notice, and should not be construed as a commitment by ASUS.
ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual,
including the products and software described in it.
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
E22942
Revised Edition V4
November 2023
iii
Contents
Safety information ...................................................................................................... vi
About this guide .......................................................................................................... x
Chapter 1: Product Introduction
1.1 System package contents ......................................................................... 1-2
1.2 Serial number label .................................................................................... 1-3
1.3 System specifications ...............................................................................1-4
1.4 Front panel features ...................................................................................1-6
1.5 Rear panel features ....................................................................................1-6
1.6 Internal features .........................................................................................1-7
1.7 LED information .........................................................................................1-8
1.7.1 Front panel LEDs ........................................................................ 1-8
1.7.2 Storage device status LEDs ........................................................ 1-9
1.7.3 Rear panel LEDs ......................................................................... 1-9
1.7.4 LAN (RJ45) LEDs...................................................................... 1-10
1.7.5 Q-Code table ............................................................................. 1-11
Chapter 2: Hardware Information
2.1 Chassis cover .............................................................................................2-2
2.1.1 Removing the rear cover ............................................................. 2-2
2.1.2 Removing the backplane cover ................................................... 2-3
2.2 Air duct(s) ...................................................................................................2-4
2.2.1 Removing the air duct(s) ............................................................. 2-4
2.2.2 Installing the air duct(s) ............................................................... 2-5
2.3 Central Processing Unit (CPU) .................................................................2-6
2.3.1 Installing the CPU and heatsink .................................................. 2-6
2.3.2 Installing the heatsink..................................................................2-9
2.4 System memory .......................................................................................2-11
2.4.1 Overview ................................................................................... 2-11
2.4.2 Memory Configurations ............................................................. 2-12
2.4.3 Installing a DIMM ...................................................................... 2-13
2.4.4 Removing a DIMM .................................................................... 2-13
2.5 (optional) Front bezel ...............................................................................2-14
2.5.1 Removing the front bezel .......................................................... 2-14
2.5.2 Installing the front bezel ............................................................ 2-15
2.6 Storage devices........................................................................................2-16
2.6.1 Installing a 2.5-inch storage device to a front storage bay ........ 2-17
2.6.2 Installing a 2.5-inch storage device to an internal storage bay
(only for Mid storage bays SKU) ............................................... 2-18
iv
2.7 Expansion slots ........................................................................................2-21
2.7.1 Installing an expansion card to the riser card bracket ............... 2-22
2.7.2 Installing an expansion card to the butterfly
riser card bracket ...................................................................... 2-24
2.7.3 Installing an HBA/RAID card ..................................................... 2-26
2.7.4 Installing the Cache Vault Power Module ................................. 2-28
2.7.5 Installing M.2 (NGFF) cards ...................................................... 2-30
2.7.6 Installing an OCP 3.0 card ........................................................ 2-32
2.7.7 Configuring an expansion card ................................................. 2-33
2.8 Cable connections ...................................................................................2-34
2.9 SATA/SAS backplane cabling .................................................................2-35
2.10 Storage device configuration and cabling ............................................2-36
2.10.1 12 x SATA (front bay), and 4 x SATA (internal bay)
storage device configuration and cabling .................................. 2-37
2.10.2 12 x NVMe (front bay), and 4 x NVMe (internal bay)
storage device configuration and cabling .................................. 2-40
2.11 Removable/optional components ...........................................................2-43
2.12 Rail Kit Options ........................................................................................2-45
Chapter 3: Motherboard Information
3.1 Motherboard layout ....................................................................................3-2
3.2 Central Processing Unit (CPU) .................................................................3-5
3.3 Dual Inline Memory Module (DIMM) ..........................................................3-5
3.4 Jumpers ......................................................................................................3-6
3.5 Internal LEDs ............................................................................................ 3-11
3.6 Internal connectors ..................................................................................3-14
Chapter 4: BIOS Setup
4.1 Managing and updating your BIOS ..........................................................4-2
4.1.1 ASUS CrashFree BIOS 3 utility................................................... 4-2
4.1.2 ASUS EZ Flash Utility ................................................................. 4-3
4.1.3 BUPDATER utility ....................................................................... 4-4
4.2 BIOS setup program ..................................................................................4-6
4.2.1 BIOS menu screen ...................................................................... 4-7
4.2.2 Menu bar ..................................................................................... 4-7
4.2.3 Menu items..................................................................................4-8
4.2.4 Submenu items ........................................................................... 4-8
4.2.5 Navigation keys ........................................................................... 4-8
4.2.6 General help................................................................................4-8
4.2.7 Configuration fields ..................................................................... 4-8
4.2.8 Pop-up window............................................................................4-8
4.2.9 Scroll bar ..................................................................................... 4-8
v
4.3 Main menu ..................................................................................................4-9
4.4 Performance Tuning menu ......................................................................4-10
4.5 Advanced menu .......................................................................................4-12
4.5.1 Trusted Computing.................................................................... 4-12
4.5.2 Redfish Host Interface Settings................................................. 4-13
4.5.3 AMD CBS .................................................................................. 4-13
4.5.4 Onboard LAN Configuration ...................................................... 4-22
4.5.5 Serial Port Console Redirection ................................................ 4-23
4.5.6 CPU Configuration .................................................................... 4-25
4.5.7 PCI Subsystem Settings ........................................................... 4-26
4.5.8 USB Configuration .................................................................... 4-31
4.5.9 Network Stack Configuration..................................................... 4-32
4.5.10 NVMe Configuration .................................................................. 4-33
4.5.11 SATA Configuration .................................................................. 4-34
4.5.12 Offboard SATA Controller Configuration ................................... 4-34
4.5.13 APM Configuration .................................................................... 4-34
4.5.14 AMD Mem Configuration Status................................................ 4-35
4.5.15 T1s Auth .................................................................................... 4-36
4.5.16 Driver Health ............................................................................. 4-36
4.5.17 Third-party UEFI driver configurations ...................................... 4-37
4.6 Chipset menu ...........................................................................................4-38
4.7 Security menu ..........................................................................................4-39
4.8 Boot menu ................................................................................................4-43
4.9 Tool menu ................................................................................................. 4-44
4.10 Event Logs menu .....................................................................................4-45
4.10.1 Change Smbios Event Log Settings ......................................... 4-46
4.10.2 View Smbios Event Log ............................................................ 4-47
4.11 Server Mgmt menu ...................................................................................4-48
4.11.1 System Event Log ..................................................................... 4-49
4.11.2 BMC network configuration ....................................................... 4-50
4.11.3 View System Event Log ............................................................ 4-52
4.12 Exit menu .................................................................................................. 4-53
Appendix
K14PA-U24 block diagram ..................................................................................... A-2
Notices .................................................................................................................... A-3
Service and Support ............................................................................................... A-7
vi
Safety information
Electrical Safety
Before installing or removing signal cables, ensure that the power cables for the system
unit and all attached devices are unplugged.
To prevent electrical shock hazard, disconnect the power cable from the electrical
outlet before relocating the system.
When adding or removing any additional devices to or from the system, ensure that the
power cables for the devices are unplugged before the signal cables are connected.
If possible, disconnect all power cables from the existing system before you add a
device.
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service
technician or your dealer.
Sécurité électrique
Avant d’installer ou de retirer des câbles, assurez-vous que les câbles d’alimentation du
système et de tous les périphériques sont débranchés.
Pour éviter tout risque de choc électrique, débranchez le câble d’alimentation de la prise
électrique avant de toucher au système.
Lors de l’ajout ou du retrait de périphériques, vérifiez que les câbles d’alimentation sont
débranchés avant de brancher d’autres câbles. Si possible, déconnectez tous les câbles
d’alimentation du système avant d’y installer un périphérique.
Si le bloc d’alimentation est endommagé, nessayez pas de le réparer vous-même. Contactez
un technicien électrique qualifié ou votre revendeur.
vii
Operation Safety
Any mechanical operation on this server must be conducted by certified or experienced
engineers.
Before operating the server, carefully read all the manuals included with the server
package.
Before using the server, ensure all cables are correctly connected and the power
cables are not damaged. If any damage is detected, contact your dealer as soon as
possible.
To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Place the server on a stable surface.
If you encounter technical problems with the product, contact a qualified service
technician or your retailer.
This product is equipped with a three-wire power cable and plug for the user’s safety. Use
the power cable with a properly grounded electrical outlet to avoid electrical shock.
Sécurité de fonctionnement
Toute opération mécanique sur ce serveur doit être effectuée par des ingénieurs certifiés ou
expérimentés.
Avant d'utiliser le serveur, lisez attentivement tous les manuels fournis avec ce dernier.
Avant d'utiliser le serveur, vérifiez que tous les câbles sont bien branchés et que les câbles
d'alimentation ne sont pas endommagés. Si des dommages sont détectés, contactez votre
revendeur dès que possible.
Pour éviter les court-circuits, gardez les clips, les vis et les agrafes loin des connecteurs, des
slots, des interfaces de connexion et de la circuiterie.
Évitez la poussière, l'humidité et les températures extrêmes. Placez le serveur sur une surface
stable.
Si vous rencontrez des problèmes techniques avec votre produit, contactez un technicien
qualifié ou votre revendeur.
Ce produit est équipé d’un câble d’alimentation et d’une prise tripolaires pour la sécurité de
l’utilisateur. Utilisez le câble d’alimentation sur une prise électrique correctement reliée à la
terre pour éviter les chocs électriques.
viii
Heavy System
CAUTION! This server system is heavy. Ask for assistance when moving
or carrying the system.
Lithium-Ion Battery Warning
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
Restricted Access Location
This product is intended for installation only in a Computer Room where:
Access can only be gained by SERVICE PERSONS or by USERS who have been
instructed about the reasons for the restrictions applied to the location and about any
precautions that shall be taken.
Access is through the use of a TOOL, or other means of security, and is controlled by
the authority responsible for the location.
Emplacement d’accès restreint
Ce produit est destiné à être installé uniquement dans une salle informatique où :
Laccès est uniquement accordé aux TECHNICIENS ou UTILISATEURS qui ont connaissance des
raisons de cette restriction et des précautions qui devraient être prises.
Laccès se fait par le biais d’un OUTIL ou tout dispositif de sécurité, et est contrôlé par l’autorité
responsable de cet emplacement.
Système lourd
ATTENTION ! Ce serveur est un système lourd. Demandez de l'aide pour
déplacer ou transporter le système.
Avertissement sur les batteries Lithium-Ion
ATTENTION ! Danger d'explosion si la batterie n'est pas correctement
remplacée. Remplacer uniquement par une batterie de type identique ou
équivalent, comme recommandé par le fabricant. Jetez les batteries usagées
conformément aux instructions du fabricant.
ix
To prevent exposure to the optical drive’s laser, do not attempt to disassemble or repair the
optical drive by yourself. For your safety, contact a professional technician for assistance.
CLASS 1 LASER PRODUCT
Optical Drive Safety Information
Laser Safety Information
Risque d'exposition dangereuse au laser. Ne tentez pas de démonter ou réparer le
lecteur de disque optique. Pour votre sécurité, faites réparer le lecteur de disque optique
uniquement par un prestataire de dépannage agréé.
Informations de sécurité concernant le lecteur optique
Informations de sécurité relatives au laser
PRODUIT LASER DE CLASSE 1
x
About this guide
Audience
This user guide is intended for system integrators, and experienced users with at least basic
knowledge of configuring a server.
Contents
This guide contains the following parts:
1. Chapter 1: Product Introduction
This chapter describes the general features of the server, including sections on front
panel and rear panel specifications.
2. Chapter 2: Hardware Information
This chapter lists the hardware setup procedures that you have to perform when
installing or removing system components.
3. Chapter 3: Motherboard Information
This chapter gives information about the motherboard that comes with the server. This
chapter includes the motherboard layout, jumper settings, and connector locations.
4. Chapter 4: BIOS Setup
This chapter tells how to change system settings through the BIOS Setup menus and
describes the BIOS parameters.
xi
References
Refer to the following sources for additional information and for product and software updates.
1. ASUS Control Center (ACC) user guide
This manual tells how to set up and use the proprietary ASUS server management
utility. Visit asuscontrolcenter.asus.com for more information.
2. ASUS websites
The ASUS websites provide updated information for all ASUS hardware and software
products. Visit https://www.asus.com for more information.
Conventions
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
Typography
Bold text Indicates a menu or an item to select.
Italics
Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greater-than sign
means that you must press the enclosed key.
Example: <Enter> means that you must press the Enter
or Return key.
<Key1>+<Key2>+<Key3> If you must press two or more keys simultaneously, the
key names are linked with a plus sign (+).
Example: <Ctrl>+<Alt>+<Del>
Command Means that you must type the command exactly as
shown, then supply the required item or value enclosed in
brackets.
Example: At the DOS prompt, type the command line:
format A:/S
DANGER/WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when
trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.
xii
This chapter describes the general features of the server. It
includes sections on front panel and rear panel specifications.
1
Product Introduction
Chapter 1: Product Introduction
Chapter 1: Product Introduction
1-2
1.1 System package contents
Check your system package for the following items.
RS500A-E12-RS12U
Chassis ASUS 1U Rackmount Chassis
Motherboard ASUS K14PA-U24 Server Board
Components
1 x Storage Device Backplane
12 x 2.5-inch Storage Device Trays or Dummy Trays
2 x Riser Cards
7 x System Fans
Accessories 1 x CPU Heatsink
2 x AC Power Cables
Optional Items
1 x Mid 4-bay Cage (only for Mid storage bays SKU)
1 x Friction Rail Kit or 1 x Ball Bearing Rail Kit
2 x 1200W Redundant Power Supply or
2 x 1600W Redundant Power Supply
If any of the above items is damaged or missing, contact your retailer.
Optional items come bundled if you selected them when purchasing the system and
cannot be bought separately.
ASUS RS500A-E12 Series 1-3
1.2 Serial number label
Before requesting support from the ASUS Technical Support team, you must take note of the
product’s serial number containing 12 characters, such as xxSxxxxxxxxx, as shown in the
figure below. With the correct serial number of the product, ASUS Technical Support team
members can then offer a quicker and satisfying solution to your problems.
xxSxxxxxxxxx
RS500A-E12-RS12U
Chapter 1: Product Introduction
1-4
1.3 System specifications
The ASUS RS500A-E12-RS12U server is a 1U barebone server system featuring the ASUS
K14PA-U24 Server Board. The server supports AMD EPYC™ 9004 Series processors plus
other latest technologies through the chipsets onboard.
Model Name RS500A-E12-RS12U
Motherboard K14PA-U24
Processor Support
1 x Socket SP5 (LGA-6096)
4th Genenration AMD EPYC™ processors with AMD 3D V-Cache
technology
AMD EPYC™ 9004 series processors (up to 400W)
Core Logic System on Chip (SoC)
Memory
Total Slots 24 (12 channels per CPU, 2 DIMMs per channel)
Capacity Maximum 6144GB
Memory Type
DDR5 4800/4400/4000/3600 RDIMM/ 3DS RDIMM
1 DPC up to 4800
2 DPC up to 4000 (1R+1R)
2 DPC up to 3600 (1R+2R)/(2R+2R)
* Please refer to www.asus.com for latest momory AVL update
Memory Size
256GB,128GB, 64GB, 32GB RDIMM
256GB,128GB, 64GB, 32GB 3DS RDIMM
* Refer to www.asus.com for the latest memory AVL update.
Expansion
Slots
Total PCI/PCI-X/
PCI-E Slots 3+1
Slot Type
1 x PCIe x16 slot (Gen5 x16 link, FH, HL)
1 x PCIe x16 slot (Gen5 x16 link, LP, HL)
1 x PCIe x16 slot (Gen5 x8 link, LP, HL)
1 x OCP3.0 socket (Gen5 x16 link)
Disk
Controller
SATA Controller
CPU Integrated
2 x M.2 connectors (SATA3 6Gb/s & PCIe Gen5 x4 link)
1 x SATA controller (SATA3 6Gb/s)
SAS Controller Optional kit(s):
ASUS PIKE II 3008 8-port SAS 12Gb/s HBA card
Storage
Bays
Front:
12 x 2.5” Hot-swap Storage Bays
(backplane supports 12 x SATA/SAS*/NVMe)
* SAS support only from optional SAS HBA/RAID card.
Internal (only for Mid storage bays SKU):
4 x 2.5” Internal Storage Bays
(backplane supports up to 16 x SATA/SAS*/NVMe)
* SAS support only from optional SAS HBA/RAID card.
Backplane
connectors
6 x MCIO x2 (for NVMe)
3 x SlimSAS x4 (for SATA)
Motherboard
onboard
connectors
2 x M.2 connectors
8 x SlimSAS connectors
(continued on the next page)
ASUS RS500A-E12 Series 1-5
Model Name RS500A-E12-RS12U
Networking 1 x Dual Port Intel® I350 Gigabit LAN Controller
1 x Management Port (BMC, AST2600)
VGA Aspeed AST2600 256MB
Graphic Up to 2 single-wide GPU
Rear I/O Ports
2 x USB 3.2 Gen 1 ports
2 x Gigabit LAN ports (RJ45)
1 x Management port (RJ45)
1 x VGA port
Switch/LED
Rear:
1 x Power Button/LED
1 x Location Button/LED
1 x Message LED
1 x Q-Code (Port 80) LED
Front:
1 x Power Button/LED
1 x Location Button/LED
1 x Message LED
2 x LAN LED
OS Support Please find the latest OS support from http://www.asus.com/
Management
Solution
Software ASUS Control Center
Out of Band
Remote
Management
ASMB11-iKVM (on-board)
Regulatory Compliance CE, FCC, BSMI, RCM
Dimension
(HH x WW x DD)
843mm x 449mm x 44mm (1U)
33.17” x 17.68” x 1.73”
Net Weight Kg 14.16 Kg (CPU, DRAM & Storage device not included)
Gross Weight Kg 19.16 Kg (CPU, DRAM & Storage device not included, Packing
included)
Power Supply
(following different
configuration by region)
1+1 Redundant 1200W 80 PLUS Platinum Power Supply or
1+1 Redundant 1600W 80 PLUS Platinum Power Supply or
1+1 Redundant 1600W 80 PLUS Titanium Power Supply
Environment
Operating temperature: 10°C ~ 35°C
Non-operating temperature: -40°C ~ 60°C
Non-operating humidity: 20% ~ 90% ( Non-condensing)
* Specifications are subject to change without notice.
Chapter 1: Product Introduction
1-6
1.4 Front panel features
The barebone server displays a simple yet stylish front panel with easily accessible features.
The power and reset buttons, LED indicators, slim type optical drive, and other ports and
buttons are located on the front panel, this may vary between models.
Refer to the Front panel LEDs section for the LED descriptions.
RS500A-E12-RS12U
Bays 1 to 12 support NVMe/SATA/SAS. SAS support requires an optional HBA/RAID
card.
All bays support 2.5” drives with trays.
Asset tag
Rack screw Rack screw
Power LED
LAN1 LED
LAN2 LED Location LED
Message LED
Power button Reset button
Location button
Bay 1 Bay 3 Bay 5 Bay 7 Bay 9 Bay 10 Bay 11 Bay 12
Bay 2 Bay 4 Bay 6 Bay 8
1.5 Rear panel features
The rear panel includes expansion slots and system power socket. The middle part includes
the I/O shield with openings for the rear panel connectors on the motherboard.
Management LAN port is for ASUS ASMB11-iKVM only.
The Q-Code LED provides the most probable cause of an error code as a starting
point for troubleshooting. The actual cause may vary from case to case.
Refer to the Q-Code table for details.
Q-Code LED
Expansion slot Expansion slot Expansion slot
OCP 3.0 slot
Power button with LED
VGA port
Location button with LED
Redundant Power supply
and Power cord connector
USB 3.2 Gen 1 ports
Management LAN port
LAN port 1
LAN port 2
ASUS RS500A-E12 Series 1-7
1.6 Internal features
The barebone server includes the basic components as shown.
WARNING
HAZARDOUS MOVING PARTS
KEEP FINGERS AND OTHER BODY PARTS AWAY
1. Redundant power supply
2. Butterfly riser card
(Gen5 x16 link and x8 link)
3. Riser card (Gen5 x16 link)
4. OCP 3.0 module slot
5. ASUS K14PA-U24 Server
Board
6. System fans
7. 4 x 2.5” internal easy-swap
storage bays (only for Mid
storage bays SKU)
8. SATA/SAS/NVMe backplane
(hidden)
9. 12 x 2.5” storage device bays
10. Asset tag (hidden)
Turn off the system power and detach the power supply before removing or replacing any
system component.
Chapter 1: Product Introduction
1-8
1.7 LED information
1.7.1 Front panel LEDs
LED Display status Description
Power LED ON System power ON
Message LED OFF
ON
System is normal; no incoming event
A hardware monitor event is indicated
Location LED
OFF
ON
Normal status
Location switch is pressed
(Press the location switch again to turn off)
LAN LEDs
OFF
Blinking
ON
No LAN connection
LAN is transmitting or receiving data
LAN connection is present
Power LED
LAN1 LED
LAN2 LED Location LED
Power button
Location button
Message LED
Reset button
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160

Asus RS500A-E12-RS12U Manuale utente

Categoria
Schede madri
Tipo
Manuale utente

in altre lingue