Asus RS520A-E11-RS24U Manuale utente

2U Rackmount Server

User Guide

RS520A-E11-RS24U

ii

No part of this manual, including the products and software described in it, may be reproduced, transmitted,

transcribed, stored in a retrieval system, or translated into any language in any form or by any means,

except documentation kept by the purchaser for backup purposes, without the express written permission

of ASUSTeK COMPUTER INC. (“ASUS”).

ASUS provides this manual “as is” without warranty of any kind, either express or implied, including but not

limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no

event shall ASUS, its directors, officers, employees, or agents be liable for any indirect, special, incidental,

or consequential damages (including damages for loss of profits, loss of business, loss of use or data,

interruption of business and the like), even if ASUS has been advised of the possibility of such damages

arising from any defect or error in this manual or product.

Specifications and information contained in this manual are furnished for informational use only, and are

subject to change at any time without notice, and should not be construed as a commitment by ASUS.

ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual,

including the products and software described in it.

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless

such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identification or explanation and to the

owners’ benefit, without intent to infringe.

E22234

Revised Edition V5

September 2023

iii

Contents

Safety information ..................................................................................................... vii

About this guide ......................................................................................................... ix

Chapter 1: Product Introduction

1.1 System package contents ......................................................................... 1-2

1.2 Serial number label .................................................................................... 1-3

1.3 System specifications ...............................................................................1-4

1.4 Front panel features ...................................................................................1-7

1.5 Rear panel features ....................................................................................1-7

1.6 Internal features .........................................................................................1-8

1.7 LED information .........................................................................................1-9

1.7.1 Front panel LEDs ........................................................................ 1-9

1.7.2 Storage device status LED........................................................ 1-10

1.7.3 LAN (RJ-45) LEDs .................................................................... 1-11

1.7.4 Rear panel LEDs ....................................................................... 1-11

1.7.5 Q-Code table ............................................................................. 1-12

Chapter 2: Hardware Information

2.1 Chassis cover .............................................................................................2-2

2.1.1 Removing the rear cover ............................................................. 2-2

2.1.2 Removing the mid cover ............................................................. 2-3

2.2 Air ducts......................................................................................................2-4

2.2.1 Removing the air ducts ............................................................... 2-4

2.2.2 Installing the air ducts ................................................................. 2-4

2.3 Central Processing Unit (CPU) .................................................................2-5

2.3.1 Installing the CPU and heatsink .................................................. 2-5

2.4 System memory .......................................................................................2-10

2.4.1 Overview ................................................................................... 2-10

2.4.2 Memory Configurations ............................................................. 2-10

2.4.3 Installing a DIMM ...................................................................... 2-11

2.4.4 Removing a DIMM .................................................................... 2-11

2.5 Storage devices........................................................................................2-12

2.5.1 Installing a 2.5” hot-swap SATA/SAS/NVMe storage device .... 2-12

2.6 Expansion slot ..........................................................................................2-14

2.6.1 Installing an expansion card to the left PCIe riser card

bracket (on selected models) .................................................... 2-15

2.6.2 Installing an expansion card to the right PCIe riser card

bracket (on selected models) .................................................... 2-18

iv

Contents

2.6.3 Installing a ASUS PIKE II card to the right PCIe riser card

bracket ...................................................................................... 2-22

2.6.4 Installing an OCP 3.0 card to the OCP 3.0 slot ......................... 2-24

2.6.5 Installing an M.2 (NGFF) card ................................................... 2-25

2.6.6 (optional) Installing the PFR module ......................................... 2-27

2.6.7 Configuring an expansion card ................................................. 2-28

2.7 Cable connections ...................................................................................2-29

2.8 Backplane cabling ...................................................................................2-30

2.9 Storage device configuration and cabling ............................................2-31

2.9.1 24 x NVMe storage device configuration and cabling

(on selected models) .................................................................................. 2-32

2.9.2 16 x NVMe and 8 x SAS/SATA storage device configuration

and cabling ................................................................................ 2-34

2.9.3 12 x NVMe and 12 x SAS/SATA storage device configuration

and cabling ................................................................................ 2-36

2.10 Removable/optional components ...........................................................2-38

2.10.1 System fans .............................................................................. 2-38

2.10.2 Redundant power supply module.............................................. 2-40

Chapter 3: Installation Options

3.1 Tool-less Friction Rail Kit ..........................................................................3-2

3.1.1 Installing the tool-less rack rail .................................................... 3-2

3.1.2 Rail kit dimensions ...................................................................... 3-4

3.2 Ball bearing Rail Kit ...................................................................................3-5

3.2.1 Attaching the rack rails ............................................................... 3-6

3.3 Cable management arm (optional for 1200 mm rack rails) ..................3-11

3.3.1 Attaching the cable management arm ...................................... 3-11

Chapter 4: Motherboard Information

4.1 Motherboard layout ....................................................................................4-2

4.2 Jumpers ......................................................................................................4-5

4.3 Internal LEDs ............................................................................................ 4-10

4.4 Internal connectors ..................................................................................4-12

Chapter 5: BIOS Setup

5.1 Managing and updating your BIOS ..........................................................5-2

5.1.1 ASUS CrashFree BIOS 3 utility................................................... 5-2

5.1.2 ASUS EZ Flash Utility ................................................................. 5-3

5.1.3 BUPDATER utility ....................................................................... 5-4

v

Contents

5.2 BIOS setup program ..................................................................................5-6

5.2.1 BIOS menu screen ...................................................................... 5-7

5.2.2 Menu bar ..................................................................................... 5-7

5.2.3 Menu items..................................................................................5-8

5.2.4 Submenu items ........................................................................... 5-8

5.2.5 Navigation keys ........................................................................... 5-8

5.2.6 General help................................................................................5-8

5.2.7 Configuration fields ..................................................................... 5-8

5.2.8 Pop-up window............................................................................5-8

5.2.9 Scroll bar ..................................................................................... 5-8

5.3 Main menu ..................................................................................................5-9

5.4 Performance Tuning menu ......................................................................5-10

5.5 Advanced menu .......................................................................................5-12

5.5.1 Trusted Computing.................................................................... 5-13

5.5.2 PSP Firmware Versions ............................................................ 5-13

5.5.3 Redfish Host Interface Settings................................................. 5-13

5.5.4 APM Configuration .................................................................... 5-14

5.5.5 Onboard LAN Configuration ...................................................... 5-14

5.5.6 Serial Port Console Redirection ................................................ 5-15

5.5.7 CPU Configuration .................................................................... 5-18

5.5.8 PCI Subsystem Settings ........................................................... 5-18

5.5.9 USB Configuration .................................................................... 5-19

5.5.10 Network Stack Configuration..................................................... 5-20

5.5.11 CSM Configuration .................................................................... 5-21

5.5.12 NVMe Configuration .................................................................. 5-22

5.5.13 SATA Configuration .................................................................. 5-23

5.5.14 AMD Mem Configuration Status................................................ 5-23

5.6 Chipset menu ...........................................................................................5-24

5.7 Security menu ..........................................................................................5-27

5.8 Boot menu ................................................................................................5-31

5.9 Tool menu ................................................................................................. 5-32

5.10 Save & Exit menu ..................................................................................... 5-33

5.11 AMD CBS menu ........................................................................................5-34

5.11.1 CPU Common Options.............................................................. 5-35

5.11.2 DF Common Options ................................................................ 5-40

vi

5.11.3 UMC Common Option ............................................................... 5-43

5.11.4 NBIO Common Options ............................................................ 5-54

5.11.5 FCH Common Options .............................................................. 5-61

5.11.6 NTB Common Options .............................................................. 5-66

5.11.7 Soc Miscellaneous Control........................................................ 5-68

5.11.8 Workload Tuning ....................................................................... 5-69

5.12 Event Logs menu .....................................................................................5-70

5.12.1 Change Smbios Event Log Settings ......................................... 5-70

5.12.2 View Smbios Event Log ............................................................ 5-71

5.13 Server Mgmt menu ...................................................................................5-72

Chapter 6: Driver Installation

6.1 Running the Support DVD .........................................................................6-2

Appendix

KMPA-U16 block diagram ...................................................................................... A-2

Notices .................................................................................................................... A-3

Service and Support ............................................................................................... A-7

Contents

vii

Safety information

Electrical Safety

• Before installing or removing signal cables, ensure that the power cables for the system

unit and all attached devices are unplugged.

• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet

before relocating the system.

• When adding or removing any additional devices to or from the system, ensure that the

power cables for the devices are unplugged before the signal cables are connected. If

possible, disconnect all power cables from the existing system before you add a device.

• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service

technician or your dealer.

Operation Safety

• Any mechanical operation on this server must be conducted by certified or experienced

engineers.

• Before operating the server, carefully read all the manuals included with the server

package.

• Before using the server, ensure all cables are correctly connected and the power cables

are not damaged. If any damage is detected, contact your dealer as soon as possible.

• To avoid short circuits, keep paper clips, screws, and staples away from connectors,

slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Place the server on a stable surface.

• If you encounter technical problems with the product, contact a qualified service

technician or your retailer.

This product is equipped with a three-wire power cable and plug for the user’s safety. Use

the power cable with a properly grounded electrical outlet to avoid electrical shock.

viii

Heavy System

CAUTION! This server system is heavy. Ask for assistance when moving

or carrying the system.

Lithium-Ion Battery Warning

CAUTION! Danger of explosion if battery is incorrectly replaced. Replace

only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

To prevent exposure to the optical drive’s laser, do not attempt to disassemble or repair the

optical drive by yourself. For your safety, contact a professional technician for assistance.

CLASS 1 LASER PRODUCT

Optical Drive Safety Information

Laser Safety Information

ix

About this guide

Audience

This user guide is intended for system integrators, and experienced users with at least basic

knowledge of configuring a server.

Contents

This guide contains the following parts:

1. Chapter 1: Product Introduction

This chapter describes the general features of the server, including sections on front

panel and rear panel specifications.

2. Chapter 2: Hardware Information

This chapter lists the hardware setup procedures that you have to perform when

installing or removing system components.

3. Chapter 3: Installation Options

This chapter describes how to install optional components into the barebone server.

4. Chapter 4: Motherboard Information

This chapter gives information about the motherboard that comes with the server. This

chapter includes the motherboard layout, jumper settings, and connector locations.

5. Chapter 5: BIOS Setup

This chapter tells how to change system settings through the BIOS Setup menus and

describes the BIOS parameters.

6. Chapter 6: Driver Installation

This chapter provides instructions for installing the necessary drivers for different

system components.

x

References

Refer to the following sources for additional information, and for product and software

updates.

1. ASUS Control Center (ACC) user guide

This manual tells how to set up and use the proprietary ASUS server management

utility. Visit asuscontrolcenter.asus.com for more information.

2. ASUS websites

The ASUS websites provide updated information for all ASUS hardware and software

products. Visit https://www.asus.com for more information.

Conventions

To ensure that you perform certain tasks properly, take note of the following symbols used

throughout this manual.

Typography

Bold text Indicates a menu or an item to select.

Italics

Used to emphasize a word or a phrase.

<Key> Keys enclosed in the less-than and greater-than sign

means that you must press the enclosed key.

Example: <Enter> means that you must press the Enter

or Return key.

<Key1>+<Key2>+<Key3> If you must press two or more keys simultaneously, the

key names are linked with a plus sign (+).

Example: <Ctrl>+<Alt>+<Del>

Command Means that you must type the command exactly as

shown, then supply the required item or value enclosed in

brackets.

Example: At the DOS prompt, type the command line:

format A:/S

DANGER/WARNING: Information to prevent injury to yourself when trying to

complete a task.

CAUTION: Information to prevent damage to the components when

trying to complete a task.

IMPORTANT: Instructions that you MUST follow to complete a task.

NOTE: Tips and additional information to help you complete a task.

This chapter describes the general features of the chassis kit. It

includes sections on front panel and rear panel specifications.

1

Product Introduction

Chapter 1: Product Introduction

1-2

If any of the above items is damaged or missing, contact your retailer.

1.1 System package contents

Check your system package for the following items.

Model Name RS520A-E11-RS24U

Chassis ASUS R2P-C 2U Rackmount Chassis

Motherboard ASUS KMPA-U16 Server Board

Component

1+1 800W 80PLUS Platinum or 850W 80PLUS Titanium or 1200W 80PLUS Platinum

or 1600W 80PLUS Platinum Redundant Power Supply

1 x 2.5-inch Storage Device Backplane

24 x 2.5-inch Storage Device Trays or Dummy Trays

4 x System Fans (80 mm x 80 mm x 38 mm)

Accessories

1 x AMD EPYC™ Support DVD

1 x Bag of Screws

1 x CPU Heatsink

2 x AC Power Cable

Optional Items

1 x 800W 80PLUS Platinum Power Supply or 1 x 850W 80PLUS Titanium Power

Supply or 1 x 1200W/1600W 80PLUS Platinum Power Supply (Second PSU)

2 x Riser card (16 NVMe configuration & 12 NVMe configuration)

System redundant fan kit

1 x Friction Rail Kit or Ball-bearing rail kit

ASUS PIKE II 3008/3108 card

ASUS RS520A-E11-RS24U 1-3

1.2 Serial number label

The product’s serial number contains 12 characters such as xxSxxxxxxxxx and printed on the

sticker at the server's front cover.

The correct serial number of the product is required if you need to request for support from

the ASUS Technical Support team.

1 2

3 4

RESET

xxSxxxxxxxxx

RS520A-E11-RS24U

Chapter 1: Product Introduction

1-4

1.3 System specifications

The ASUS RS520A-E11-RS24U features the ASUS KMPA-U16 server board. The server

supports AMD EPYC™ 7002/7003 Series processors plus other latest technologies through

the chipsets onboard.

(continued on the next page)

Model Name RS520A-E11-RS24U

Motherboard KMPA-U16

Processor Support

1 x Socket SP3 (LGA 4094)

AMD EPYC™ 7002/7003 Series

xGMI (External Global Memory Interface Link)

Core Logic System on Chip (SoC)

Memory

Total Slots 16 (8-channel per CPU, 16 DIMM per CPU)

Capacity Maximum up to 4096GB

Memory Type DDR4 3200/2933 RDIMM/LRDIMM/3DS LRDIMM

* Please refer to www.asus.com for latest momory AVL update

Memory Size

64GB, 32GB, 16GB RDIMM

64GB, 128GB LRDIMM

64GB, 128GB, 256GB (LRDIMM 3DS/ 3DS RDIMM)

* Refer to www.asus.com/support for more information

Expansion

Slots

Total PCI/PCIe/

PIKE Slots Up to 5

Slot Type

24 x NVMe

1 x PCIe x16 slot (Gen4 x8 link, LP)(CPU1)

(GPU card support limited)

16 x NVMe or 12 x NVMe

Up to 5 PCIe Gen4 slots + 1 OCP3.0

2 x PCIe x16 slot (Gen4 x16 link, FHFL)(CPU1) or Dual-slot GPU

cards or 4 x PCIe x16 slot (Gen4 x8 link, FHFL)(CPU1)

1 x PCIe x16 slot (Gen4 x8 link, LP)(CPU1)

1 x OCP 3.0 Mezzanine slot (CPU1)

M.2 2 x M.2 (Up to 22110) (CPU1)

(Support 2 x SATA/PCIe Gen4 x2 or 1 x PCIe Gen4 x4 M.2)

Micro SD Card slot 1

Proprietary Slot 1 1 x PCIe x16 slot (Gen4 x8 link, for pike card only)

Proprietary Slot 2 -

Storage

SATA Controller Integrated in CPU

SAS Controller

Optional kits:

ASUS PIKE II 3008 8-port SAS 12Gb/s HBA card

ASUS PIKE II 3108 8-port SAS HW 12Gb/s RAID card

ASUS RS520A-E11-RS24U 1-5

Model Name RS520A-E11-RS24U

Storage

Bays Front Storage Bays

24 x 2.5” hot-swap drive bays

- 24 x NVMe or

- 16 x NVMe + 8x SAS/SATA(from pike card) or

- 12 x NVMe + 12x SAS/SATA

* SAS support only from optional SAS HBA/RAID card

Networking

1 x Dual Port Intel® I350-AM2 Gigabit LAN controller

1 x Management Port

Optional OCP Adapter:

Up to 100Gb/s Ethernet / InfiniBand Adapter

VGA Aspeed AST2600 64MB

Graphic Up to 2 x Dual slot or 4 x Single slot GPU cards supported

Front I/O Ports 2 x USB 3.2 Gen1 ports

Rear I/O Ports

2 x USB 3.2 Gen1 ports

1 x VGA port

1 x RJ-45 Mgmt LAN port

2 x RJ-45 1GbE LAN ports

Switch/LED

Front Switch/LED:

1 x Power Switch (w/ LED)

1 x Reset Switch

1 x Location Switch (w/ LED)

1 x HDD Access LED

1 x Message LED

LAN 1-2 LED

Rear Switch/LED:

1 x Port80 LED (Q-Code)

1 x Power Switch w/ LED

1 x Location Switch w/ LED

1 x Message LED

Security Options TPM-SPI

PFR

OS Support

Windows® Server 2019 64 bit

Windows® Server 2016

RedHat® Enterprise Linux

SuSE® Linux Enterprise Server

CentOS

Ubuntu

VMware

* Please find the latest OS support from https://www.asus.com/

(continued on the next page)

Chapter 1: Product Introduction

1-6

*Specifications are subject to change without notice.

Model Name RS520A-E11-RS24U

Management

Solution

Software ASUS Control Center

Out of Band

Remote

Management

On-Board ASMB10-iKVM for KVM-over-IP

Regulatory Compliance BSMI, CE, RCM, FCC(Class A)

Dimension 840mm x 449mm x 88.1mm (2U)

33.07in x 17.68in x 3.47in

Net Weight Kg (CPU, DRAM &

HDD not included) 28.74 Kg

Gross Weight Kg (CPU, DRAM

& HDD not included, Packing

include)

35.36 Kg

Power Supply

(different configuration by region)

1+1 Redundant 800W 80 PLUS Platinum Power Supply

Rating: 100-127/200-240Vac, 10A/5A (for each inlet), 50-60Hz

Class I

1+1 Redundant 850W 80 PLUS Titanium Power Supply

Rating: 100-127/200-240Vac, 11A/5A (for each inlet), 47-63Hz

or 240Vdc, 4A

1+1 Redundant 1200W 80 PLUS Platinum Power Supply

Rating: 100-127/200-240Vac, 10A/8A (for each inlet), 50-60Hz

or 240Vdc, 6A

1+1 Redundant 1600W 80 PLUS Platinum Power Supply

Rating: 100-127/200-240Vac, 10A/8A (for each inlet), 50-60Hz

or 240Vdc, 6A

240Vdc Only for China

Environment

Operation temperature: 10° ~ 35°

Non operation temperature: -40° ~ 60°

Non operation humidity: 20% ~ 90% (Non condensing)

ASUS RS520A-E11-RS24U 1-7

1.4 Front panel features

The barebone server displays a simple yet stylish front panel with easily accessible features.

The power and reset buttons, LED indicators are located on the front panel.

Refer to section 1.7 LED information for the LED descriptions.

• Bay 1 to bay 24 supports NVMe for 24 NVMe configuration.

• Bay 5 to bay 20 supports NVMe; others support SATA/SAS* from HBA/RAID for 16

NVMe configuration.

• Bay 5 to bay 16 supports NVMe, others supports SATA/SAS* for 12 NVMe

configuration.

* SAS support only from HBA/RAID card.

*This port is for ASUS ASMB10-iKVM only.

1.5 Rear panel features

The rear panel includes the expansion slots, and system power sockets. The middle part

includes the I/O shield with openings for the rear panel connectors on the motherboard.

1 2

3 4

RESET

USB 2.0 ports

Reset button

24 x 2.5" storage baysBay 1 Bay 24

Location button

Power button

Refer to 1.7 LED information

Redundant Power supply

and Power cord connector

OCP 3.0 slot

Expansion slots

Q-Code LED VGA port

Lan port 1

Lan port 2

Location button

Power button

Management LAN port 1*

USB 3.2 Gen 1 ports

Expansion slot

Chapter 1: Product Introduction

1-8

1.6 Internal features

The barebone server includes the basic components as shown.

The barebone server does not include a floppy disk drive. Connect a USB floppy disk drive

to any of the USB ports on the front or rear panel if you need to use a floppy disk.

WARNING

HAZARDOUS MOVING PARTS

KEEP FINGERS AND OTHER BODY PARTS AWAY

A protection film is pre-attached to the front cover before shipping. Please remove the

protection film before turning on the system for proper heat dissipation.

1. Redundant Power supply

2. ASUS KMPA-U16 Server

Board

3. SATA/SAS/NVMe back

panel

4. Front USB panel

5. System fans

6. Asset Tag (hidden)

7. 24 x 2.5“ storage device

trays

8. PCIe riser card or NVMe

riser card for 24 NVMe

configuration

9. Front I/O panel

ASUS RS520A-E11-RS24U 1-9

1.7 LED information

1.7.1 Front panel LEDs

Power button with LED

Location button with LED

Message LED

LAN 1 LED

LAN 2 LED

LAN 4 LED

LAN 3 LED

Storage Device Access LED

1 2

3 4

RESET

LED Icon Display status Description

Power button with LED ON System power on

Storage Device

Access LED

OFF No activity

Blinking Read/write data into the storage device

Message LED

OFF System is normal; no incoming event

ON With the onboard ASMB10-iKVM: a

hardware monitor event is indicated

Location button with

LED

ON Location switch is pressed

OFF Normal status (Press the location switch

again to turn off)

LAN LEDs

1

2

3

4

OFF No LAN connection

Blinking LAN is transmitting or receiving data

ON LAN connection is present

Chapter 1: Product Introduction

1-10

1.7.2 Storage device status LED

1 2

3 4

RESET

Red LED

Green LED

Storage Device LED Description

Status (RED) ON Storage device has failed

Blinking RAID rebuilding or locating

Activity (GREEN)

ON Storage device power ON

Blinking Read/write data from/into the SATA/SAS storage device

OFF Storage device not found

La pagina sta caricando ...

Asus RS520A-E11-RS24U Manuale utente

Asus RS520A-E11-RS24U Manuale utente

in altre lingue

Documenti correlati

Altri documenti