Mettler Toledo PUA series CEU Manuale utente

PT

PUA-series

Weighing platforms

ENDEFRESITNL

User manual

PUA579(x)mobile

PUA574 / PUA579(x)

2

PUA-series 30290730C

Contents

English ........................................................................................... 3

Deutsch .........................................................................................16

Français ....................................................................................... 29

Español ........................................................................................ 42

Italiano ........................................................................................ 55

Nederlands ................................................................................... 68

Português ......................................................................................81

EN

3

30290730C PUA-series

English (Original instructions)

Congratulations on choosing the quality and precision of METTLER TOLEDO. Proper

use of your new equipment according to this User manual and regular calibration and

maintenance by our factory-trained service team ensures dependable and accurate

operation, protecting your investment. Contact us about a service agreement tailored to

your needs and budget. Further information is available at

www.mt.com/service.

There are several important ways to ensure you maximize the performance of your

investment:

1. Register your product: We invite you to register your product at

www.mt.com/productregistration

so we can contact you about enhancements, updates and important notications

concerning your product.

2. Contact METTLER TOLEDO for service: The value of a measurement is proportional

to its accuracy – an out of specication scale can diminish quality, reduce prots and

increase liability. Timely service from METTLER TOLEDO will ensure accuracy and

optimize uptime and equipment life.

– Installation, Conguration, Integration and Training:

Our service representatives are factory-trained weighing equipment experts. We

make certain that your weighing equipment is ready for production in a cost

effective and timely fashion and that personnel are trained for success.

– Initial Calibration Documentation:

The installation environment and application requirements are unique for every

industrial scale so performance must be tested and certied. Our calibration

services and certicates document accuracy to ensure production quality and

provide a quality system record of performance.

– Periodic Calibration Maintenance:

A Calibration Service Agreement provides on-going condence in your weighing

process and documentation of compliance with requirements. We offer a variety

of service plans that are scheduled to meet your needs and designed to t your

budget.

PUA-series weighing platforms

1 Safety instructions...............................................................................................5

1.1 Intended use ........................................................................................................5

1.2 Misuse .................................................................................................................5

1.3 General safety precautions .....................................................................................5

1.4 Safety precautions for operation in hazardous areas .................................................5

1.5 Safety precautions for mobile weighing platforms ..................................................... 5

2 Introduction .........................................................................................................6

2.1 PUA-series low prole weighing platforms ...............................................................6

2.2 About this user manual..........................................................................................6

2.3 Further documents ................................................................................................ 6

3 Operation ............................................................................................................ 7

3.1 Checking the location ............................................................................................7

3.2 Checking the weighing platform..............................................................................7

3.3 Important notes ....................................................................................................8

3.4 Operation with access ramps ................................................................................. 9

3.5 Instructions for PUA579(x) mobile ..........................................................................9

3.6 Installation, service and repair .............................................................................. 11

4 Maintenance ..................................................................................................... 12

4.1 Notes on cleaning ............................................................................................... 12

4.2 Cleaning from below (in conjunction with a lifting device) ....................................... 13

4.3 Subsequent treatment .......................................................................................... 14

4.4 Disposal ............................................................................................................ 14

5 Technical data and operating limits .................................................................... 14

5.1 Maximum verication scale interval ...................................................................... 14

5.2 Maximum permissible load .................................................................................. 15

5.3 Ambient conditions ............................................................................................. 15

5.4 Digital weighing interface specication (safe area only) .......................................... 15

5.5 Connectivity to weighing terminals ........................................................................ 15

5.6 Specications for Category 2 / Category 3 ............................................................. 15

4

PUA-series 30290730C

1 Safety instructions

1.1 Intended use

PUA-series low prole weighing platforms are part of a modular weighing system consisting

of a METTLER TOLEDO weighing terminal as indicator and at least one weighing platform.

➜ Use the weighing platform only for weighing in accordance with this user manual.

➜ The weighing platform is intended for indoor use only.

➜ Any other type of use is considered as not intended.

➜ For driving over the low prole weighing platform only use pallet trucks. For weight

limits refer to page 15.

Legal metrology

➜ For use in legal metrology only use approved weighing platforms.

➜ When using in legal metrology, the operating company is responsible for observing

all the national weights & measurements requirements.

➜ Please contact the METTLER TOLEDO Service organization for questions related to the

use in legal for trade applications.

1.2 Misuse

▲ Do not use the weighing platform other than for weighing operations.

▲ Do not use the weighing platform in an other environment or category than specied

in the table in section 2.1.

▲ Do not modify the weighing platform.

▲ Do not use the weighing platform beyond the limits of technical specications.

▲ Do not use the weighing platform for storing goods.

▲ Avoid falling goods on the weighing platform.

1.3 General safety precautions

▲ Use only genuine METTLER TOLEDO accessories and cable assemblies with this

product. Use of unauthorized or counterfeit accessories or cable assemblies may

result in voided warranty, improper or erroneous operation, or damage to property

(including the unit) and personal injury.

1.4 Safety precautions for operation in hazardous areas

Specic weighing platforms of the PUA-series are approved according to Category 2 or

Category 3, see section 2.1.

The operating company is responsible for the safe operation of the explosion protected

weighing system.

▲ Strictly observe the safety instructions of the operating company.

▲ Comply with all national regulations for operation in hazardous areas, as well as the

instructions and information in this user manual.

1.5 Safety precautions for mobile weighing platforms

▲ Only instructed personnel may operate the mobile weighing platforms.

EN

5

Safety instructions 30290730C PUA-series

2 Introduction

2.1 PUA-series low prole weighing platforms

This user manual focuses on the products listed below.

The PUA-series offers a variety of weighing platforms to t your requirements.

Each type is available

• in various sizes and capacities,

• as approved or non-approved version.

Type Material Environment Ex approval

PUA574 Painted Dry –

PUA579

Stainless steel Wet

analog versions only:

Category 3

PUA579mobile

PUA579x

Category 2

PUA579xmobile

2.2 About this user manual

This user manual contains all information for the operator of the weighing platforms of

the PUA-series.

➜ Read this user manual carefully before use.

➜ Keep this user manual for future reference.

➜ Pass this user manual to any future owner or user of the product.

2.3 Further documents

In addition to this printed user manual you can download the following documents from

www.mt.com:

• Brochure

• Technical data sheet

• Installation information (for trained personnel under the control of the operating

company)

6

Introduction

PUA-series 30290730C

Type approval documents for use in hazardous areas

Mechanic assessment of

weighing platforms Category 2 /

Category3

PUA579(x)

PUA579(x)mobile

BVS 05 ATEX H/B 116

Category 3 Load cells /

scale interfaces

Load cell 0745A KEMA 03ATEX1070

Used until June 2019: System solution Analog Ex2

System component Analog Ex2

BVS 08 ATEX E 063

Used as from March 2019: AJB579xx-a BVS 18 ATEX E 008

Category 2 Load cells /

scale interfaces

Load cell 0745A KEMA 03ATEX1069

Used until June 2019: System solution Analog Ex1 BVS 04 ATEX E 221

Used as from March 2019: AJB579x-a BVS 18 ATEX E 007

3 Operation

3.1 Checking the location

The correct location is crucial for the accuracy of the weighing results.

1. Ensure that the location of the weighing platform is stable, vibration-free and horizontal.

2. Observe the following environmental conditions:

– No direct sunlight

– No strong drafts

– No excessive temperature uctuations

3.2 Checking the weighing platform

Function check

Before starting a weighing series, perform a function check of the weighing platform and

the connected weighing terminal.

1. Make sure that the lifting device is closed and locked correctly.

2. Make sure that the weighing platform is connected to a weighing terminal and that the

weighing terminal is switched on.

3. Make sure that the weighing platform is unloaded and the display of weighing terminal

shows 0.

4. Load the weighing platform.

The display must show a value different from 0.

5. Unload the weighing platform.

The display must return to 0.

0.000 kg

10.520 kg

0.000 kg

EN

7

Operation 30290730C PUA-series

Verication test

For a verication test refer to the user manual of the connected weighing terminal.

If the verication seal is broken, verication is no longer valid.

3.3 Important notes

For best weighing results observe the following:

▲ To achieve best weighing results place the weighing sample always in the middle of

the weighing platform.

▲ Avoid abrasive and wear processes.

▲ Avoid falling loads, shocks and lateral impacts.

8

Operation

PUA-series 30290730C

3.4 Operation with access ramps

The load plate of the weighing platform is an active weighing component. The access

ramps are passive.

➜ Make sure that during the weighing process all wheels of the transport vehicle are on

the load plate.

➜ Make sure that the gap (1) between weighing platform and ramp is free from dirt

deposits.

3.5 Instructions for PUA579(x) mobile

3.5.1 Safety notes

WARNING

Danger of crushing.

▲ Only instructed personnel may operate the mobile weighing platforms.

▲ Operate the mobile weighing platform only from the side.

▲ Operate the roller boxes only with both hands.

PUA

1

EN

9

Operation 30290730C PUA-series

CAUTION

Damage to and/or malfunction of the mobile weighing platform.

▲ Weighing samples or other loads are not permitted on the mobile weighing platform

while moving it.

▲ Put on weighing samples only in weighing mode.

CAUTION

Damage to and/or malfunction of the mobile weighing platform.

1

2

▲ Ensure that the connection cable does not touch the oor.

▲ Use only the drawbar (1) to pull or push the unit in moving mode. Under no

circumstances pull or push at the stand (2).

3.5.2 Establishing the moving mode

1. Start at roller box 1 (moving roller).

2. Unbolt the lock (A) with one hand and keep it pulled out.

3. Use the other hand to tilt the lever (B) downwards until the lock latches in again.

4. Proceed at roller boxes 2 to 4 as described under steps 2 and 3.

A

B

3

2 1

4

10

Operation

PUA-series 30290730C

5. Hang out the access ramp (1) and put aside or respectively pull out the Rampx

under the weighing platform.

6. Tilt the drawbar (2) forwards and move the scale

3.5.3 Establishing the weighing mode

1. Tilt the drawbar downwards onto the weighing platform.

2. Start at roller box 4.

3. Unbolt the lock (A) with one hand and keep it pulled out.

4. Use the other hand to tilt the lever (B) upwards until the lock latches in again.

5. Proceed at roller boxes 3 to 1 as described in steps 2 and 3.

6. Check whether the weighing platform is positioned correctly.

7. Check the level of the weighing platform.

3.6 Installation, service and repair

➜ For installation, conguration, service and repair of the weighing platforms call the

METTLER TOLEDO Service.

1

2

3

2 1

4

A

B

EN

11

Operation 30290730C PUA-series

4 Maintenance

Maintenance of the weighing platform is limited to regular cleaning and subsequent oiling

for stainless steel versions.

4.1 Notes on cleaning

NOTICE

Damage to the weighing platform due to incorrect use of cleaning agents.

▲ Use only such cleaning agents that do not act on the plastics used in the weighing

platform.

▲ Only use disinfectants and cleaning agents in accordance with the manufacturer's

instructions.

▲ Do not use highly acidic, highly alkaline or highly chlorinated cleaning agents.

Avoid substances with a high or low pH value, otherwise increased danger of

corrosion exists.

▲ Be particularly careful when cleaning from below (in conjuction with a lifting device).

➜ Remove dirt and deposits at regular intervals from above and below the weighing

platform.

– The procedure depends both on the type of surface and on the environmental

conditions prevailing at the installation location.

– Cleaning from below only in conjunction with a lifting device.

Cleaning in a dry environment (painted version)

➜ Wipe with a damp cloth.

➜ Use household cleaning agents.

Cleaning in a corrosive environment (stainless steel version)

➜ Use a water jet up to 80 °C / 176 °F and max. 80 bars, minimum distance 40 cm.

➜ Remove corrosive substances at regular intervals.

➜ Only use disinfectants and cleaning agents in accordance with the manufacturer's

specications and instructions.

➜ Check the gap between the weighing platform and the access ramp/wheel set and

remove any soiling.

12

Maintenance

PUA-series 30290730C

4.2 Cleaning from below (in conjunction with a lifting device)

To tilt the low prole weighing platform, a lifting device is available from METTLER TOLEDO.

For installing and operating the lifting device refer to the corresponding documentation

(ME-22015711 and ME-22016758).

Safety precautions for operating the lifting device

▲ Do not operate the lifting device outside the temperature range of –10 °C to +40 °C/

14°Fto104°F. Otherwise, the safety of the pneumatic springs is not guaranteed.

▲ Only instructed personnel may operate the lifting device.

▲ The lifting device must be checked to ensure compliance with the safety requirements

before being put into service for the rst time, following any service work and at least

every 3 years.

CAUTION

Even minor damage, corrosion or ecks of paint on the piston rod lead to failure of

the pneumatic springs.

▲ Protect pneumatic springs against soiling and damage.

1. Tilt the weighing platform with a lifting device.

2. Remove corrosive substances, dirt and deposits regularly from the surface.

3. Use a water jet up to 60°C / 140 °F, max. 2bars, minimum distance 40 cm.

4. Use compressed air to remove dirt particles from the gap (A) between the overload

protection of the load sensor and the load frame of the weighing platform.

A

EN

13

Maintenance 30290730C PUA-series

4.3 Subsequent treatment

In order to protect the weighing platform, carry out the following subsequent treatment:

➜ Rinse the weighing platform with clear water and remove cleaning agent completely.

➜ Dry off the weighing platform with a lint-free cloth.

➜ Oil the stainless steel weighing platform regularly from above and below with an oil

suitable for foodstuffs.

4.4 Disposal

In conformance with the European Directive 2002/96 EC on Waste Electrical and Electronic

Equipment (WEEE), this device may not be disposed of with domestic waste. This also

applies to countries outside the EU, according to their specic requirements.

➜ Please dispose of this product in accordance with local regulations at the collecting

point specied for electrical and electronic equipment.

Disposal of pneumatic springs of the lifting device

• The pneumatic springs must not be opened or heated.

• The pneumatic springs may only be opened according to the manufacturer's

instructions.

• The oil lling of the pneumatic springs must be disposed of according to the

manufacturer's instructions.

5 Technical data and operating limits

5.1 Maximum verication scale interval

The verication scale interval depends on the load cell and scale conguration. The

maximum verication scale interval is given below.

Max. verication

scale interval [e]

Capacity

300 kg 600 kg 1200 kg 1500 kg

3 x 3000 e

Multi Range

max / e [kg]

– – –

300 / 0.1

600 / 0.2

1500 / 0.5

1 x 6000 e

Single Range [kg]

0.05 0.1 0.2 –

OIL

14

Technical data and operating limits

PUA-series 30290730C

5.2 Maximum permissible load

All weighing platforms are equipped with an overload protection. However, if the load

exceeds the maximum permissible load, damage of mechanical parts may occur.

The static load-bearing capacity, i.e. the maximum permissible load, is dependent on the

type of loading (positions A – D).

Position

PUA57..CS

PUA57..FL

PUA57..E

PUA57..FM PUA57..FH

A central load 800 kg 1850 kg 3000 kg

B side load 400 kg 900 kg 1800 kg

C one-sided cornerload 300 kg 450 kg 900 kg

D

individual wheel load

min. wheel distance 500 mm

200 kg 400 kg 800 kg

5.3 Ambient conditions

The weighing platform and the gas pressure springs of the raisable weighing platforms

may only be operated in the range of –10 °C to + 40 °C / 14° Fto104 °F.

5.4 Digital weighing interface specication (safe area only)

Interface type RS422

Interface protocol SICSpro

Max. cable length 20 m

5.5 Connectivity to weighing terminals

Weighing interface Weighing terminal

SICSpro

Any METTLER TOLEDO weighing terminal with SICSpro RS422

interface may be connected.

ACC409xx SICSpro-

IDNet adapter (option)

Only the following METTLER TOLEDO legacy IDNet weighing

terminals may be connected:

IND570, IND690, IND780, IND890, ID7, ICS__9, ICS__5.

5.6 Specications for Category 2 / Category 3

You will nd the specications for Category 2 / Category 3 in the corresponding type

approval documents, see table in section 2.3.

EN

15

Technical data and operating limits 30290730C PUA-series

16

PUA-Serie 30290730C

Deutsch (Übersetzung)

Herzlichen Glückwunsch zu Ihrer Wahl der Qualität und Präzision von METTLER TOLEDO.

Der ordnungsgemäße Gebrauch Ihres neuen Geräts gemäß dieser Bedienungsanleitung

sowie die regelmäßige Kalibrierung und Wartung durch unser im Werk geschultes

Serviceteam gewährleisten den zuverlässigen und genauen Betrieb und schützen somit

Ihre Investition. Setzen Sie sich mit uns in Verbindung, wenn Sie an einem Service-Vertrag

interessiert sind, der genau auf Ihre Anforderungen und Ihr Budget zugeschnitten ist.

Weitere Informationen erhalten Sie unter

www.mt.com/service.

Zur Optimierung des Nutzens, den Sie aus Ihrer Investition ziehen, sind mehrere wichtige

Schritte erforderlich:

1. Registrierung des Produkts: Wir laden Sie dazu ein, Ihr Produkt unter

www.mt.com/productregistration

zu registrieren, damit wir Sie über Verbesserungen, Updates und wichtige Mitteilungen

bezüglich Ihres Produkts informieren können.

2. Kontaktaufnahme mit METTLER TOLEDO zwecks Service: Der Wert einer Messung

steht im direkten Verhältnis zu ihrer Genauigkeit – eine nicht den Spezikationen

entsprechende Waage kann zu Qualitätsminderungen, geringeren Gewinnen

und einem höheren Haftbarkeitsrisiko führen. Fristgerechte Serviceleistungen von

METTLER TOLEDO stellen die Genauigkeit sicher, reduzieren Ausfallzeiten und

verlängern die Gerätelebensdauer.

– Installation, Konguration, Integration und Schulung:

Unsere Servicevertreter sind vom Werk geschulte Experten für Wägeausrüstungen.

Wir stellen sicher, dass Ihre Wägegeräte auf kostengünstige und termingerechte

Weise für den Einsatz in der Produktionsumgebung bereit gemacht werden und

dass das Bedienungspersonal so geschult wird, dass ein Erfolg gewährleistet ist.

– Dokumentation der Erstkalibrierung:

Die Installationsumgebung und Anwendungsanforderungen sind für jede

Industriewaage anders; deshalb muss die Leistung geprüft und zertiziert werden.

Unsere Kalibrierungsservices und Zertikate dokumentieren die Genauigkeit, um

die Qualität der Produktion sicherzustellen und für erstklassige Aufzeichnungen der

Leistung zu sorgen.

– Periodische Kalibrierungswartung:

Ein Kalibrierungsservicevertrag bildet die Grundlage für Ihr Vertrauen in Ihr

Wägeverfahren und stellt gleichzeitig eine Dokumentation der Einhaltung von

Anforderungen bereit. Wir bieten eine Vielzahl von Serviceprogrammen an, die auf

Ihre Bedürfnisse und Ihr Budget maßgeschneidert werden können.

Wägebrücken der PUA-Serie

1 Sicherheitshinweise .......................................................................................... 18

1.1 Vorgesehene Nutzung.......................................................................................... 18

1.2 Missbräuchliche Verwendung ............................................................................... 18

1.3 Allgemeine Sicherheitsvorkehrungen ..................................................................... 18

1.4 Sicherheitsvorkehrungen für den Betrieb in explosionsgefährdeten Bereichen ............. 19

1.5 Sicherheitsvorkehrungen für mobile Wägebrücken .................................................. 19

2 Einführung ......................................................................................................... 19

2.1 Flachbettwaagen der PUA-Serie ............................................................................ 19

2.2 Zu dieser Bedienungsanleitung ............................................................................. 19

2.3 Weitere Dokumente .............................................................................................20

3 Betrieb ..............................................................................................................20

3.1 Prüfen des Standorts ...........................................................................................20

3.2 Prüfen der Wägebrücke ....................................................................................... 21

3.3 Wichtige Hinweise............................................................................................... 21

3.4 Betrieb mit Auffahrrampen ...................................................................................22

3.5 Anleitungen für PUA579(x) mobile ........................................................................22

3.6 Installation, Service und Reparatur ........................................................................ 24

4 Wartung ............................................................................................................ 25

4.1 Hinweise zur Reinigung ....................................................................................... 25

4.2 Reinigung von unten (in Verbindung mit einer Hebevorrichtung) ..............................26

4.3 Nachbehandlung ................................................................................................26

4.4 Entsorgung .........................................................................................................27

5 Technische Daten und Betriebsgrenzen ...............................................................27

5.1 Maximaler Eichwert .............................................................................................27

5.2 Maximal zulässige Belastung ............................................................................... 27

5.3 Umgebungsbedingungen ..................................................................................... 28

5.4 Digitale Waagenschnittstelle Spezikation (nur sicherer Bereich) .............................. 28

5.5 Konnektivität zu Wägeterminals ............................................................................28

5.6 Spezikationen für Kategorie 2 / Kategorie 3 .......................................................... 28

DE

17

30290730C PUA-Serie

1 Sicherheitshinweise

1.1 Vorgesehene Nutzung

Flachbettwaagen der PUA-Serie sind Teil eines modularen Wägesystems, bestehend aus

einem METTLER TOLEDO Wägeterminal als Anzeige und mindestens einer Wägebrücke.

➜ Die Wägebrücke darf ausschließlich für Wägevorgänge in Übereinstimmung mit dieser

Bedienungsanleitung verwendet werden.

➜ Die Wägebrücke ist nur zur Verwendung im Innenbereich bestimmt.

➜ Jede andere Art der Verwendung gilt als nicht bestimmungsgemäß.

➜ Zum Fahren über Flachbettwaagen ausschließlich Hebefahrzeuge verwenden. Für

Gewichtsgrenzen siehe Seite 27.

Eichpichtiger Verkehr

➜ Für eine Verwendung im eichpichtigen Verkehr nur geeichte Wägebrücken verwenden.

➜ Bei einer Verwendung im eichpichtigen Verkehr ist der Betreiber für die Einhaltung

aller nationalen Vorschriften in Bezug auf Maße und Gewichte zuständig.

➜ Wenden Sie sich bei Fragen bezüglich des Einsatzes in eichpichtigen Anwendungen

an die METTLER TOLEDO Serviceorganisation.

1.2 Missbräuchliche Verwendung

▲ Die Wägebrücke ausschließlich für Wägevorgänge verwenden.

▲ Die Wägebrücke in keiner anderen Umgebung oder Kategorie verwenden, als in der

Tabelle in Abschnitt 2.1 vorgegeben ist.

▲ Keine Änderungen an der Wägebrücke vornehmen.

▲ Die Wägebrücke nicht für den Betrieb außerhalb der in den technischen Daten

vorgegebenen Grenzen verwenden.

▲ Die Wägebrücke nicht als Aufbewahrungsort von Gütern verwenden.

▲ Das Herabfallen von Gegenständen auf die Wägebrücke vermeiden.

1.3 Allgemeine Sicherheitsvorkehrungen

▲ Ausschließlich Original-Zubehörteile und -Kabelbaugruppen von METTLER TOLEDO

mit diesem Produkt verwenden. Die Verwendung nicht zugelassener oder gefälschter

Zubehörteile oder Kabelbaugruppen kann zum Erlöschen der Garantie führen und

unsachgemäßen oder fehlerhaften Betrieb oder Sachbeschädigung (einschließlich der

Einheit) und Personenverletzungen zur Folge haben.

18

Sicherheitshinweise

PUA-Serie 30290730C

1.4 Sicherheitsvorkehrungen für den Betrieb in explosionsgefährdeten

Bereichen

Bestimmte Wägebrücken der PUA-Serie sind nach Kategorie 2 oder Kategorie 3 zugelassen,

siehe die Tabelle in Abschnitt 2.1.

Der Betreiber ist für den sicheren Betrieb des explosionsgeschützten Wägesystems

verantwortlich.

▲ Die Sicherheitsanweisungen des Betreibers sind strikt zu befolgen.

▲ Alle nationalen Vorschriften zum Betrieb in explosionsgefährdeten Bereichen sowie die

Anleitungen und Informationen in dieser Bedienungsanleitung sind einzuhalten.

1.5 Sicherheitsvorkehrungen für mobile Wägebrücken

▲ Mobile Wägebrücken dürfen nur von eingewiesenem Personal bedient werden.

2 Einführung

2.1 Flachbettwaagen der PUA-Serie

In dieser Bedienungsanleitung wird der Schwerpunkt auf die nachfolgend aufgelisteten

Produkte gelegt.

Die PUA-Serie bietet eine Vielzahl an Flachbettwaagen, die auf Ihre Anforderungen

abgestimmt sind.

Jeder Typ ist verfügbar:

• in verschiedenen Größen und Kapazitäten,

• als geeichte oder nicht geeichte Ausführung.

Typ Werkstoff Umgebung Ex-Zulassung

PUA574 Lackiert Trocken –

PUA579

Edelstahl Feucht

nur analoge Versionen:

Kategorie 3

PUA579mobile

PUA579x

Kategorie 2

PUA579xmobile

2.2 Zu dieser Bedienungsanleitung

Diese Bedienungsanleitung enthält alle Informationen für den Bediener von Wägebrücken

der PUA.

➜ Diese Bedienungsanleitung vor der Verwendung sorgfältig durchlesen.

➜ Diese Bedienungsanleitung für künftige Referenzzwecke aufbewahren.

➜ Diese Bedienungsanleitung an künftige Eigentümer oder Benutzer des Produkts

weitergeben.

DE

19

Einführung 30290730C PUA-Serie

2.3 Weitere Dokumente

Außer dieser Bedienungsanleitung in Druckform können Sie über www.mt.com die

folgenden Dokumente herunterladen:

• Broschüre

• Technisches Datenblatt

• Installationsanleitung (für geschultes Personal unter Aufsicht des Betreibers)

Dokumente zur Bauartzulassung für den Einsatz in explosionsgefährdeten Bereichen

Mechanische Bewertung von

Wägebrücken

Kategorie 2 / Kategorie 3

PUA579(x)

PUA579(x)mobile

BVS 05 ATEX H/B 116

Kategorie 3

Wägezellen /

Waagenschnittstellen

Wägezelle 0745A KEMA 03ATEX1070

Verwendet bis Juni 2019: Systemlösung Analog Ex2

Systemkomponente Analog Ex2

BVS 08 ATEX E 063

Verwendet ab März 2019: AJB579xx-a BVS 18 ATEX E 008

Kategorie 2

Wägezellen /

Waagenschnittstellen

Wägezelle 0745A KEMA 03ATEX1069

Verwendet bis Juni 2019: Systemlösung Analog Ex1 BVS 04 ATEX E 221

Verwendet ab März 2019: AJB579x-a BVS 18 ATEX E 007

3 Betrieb

3.1 Prüfen des Standorts

Der richtige Standort ist entscheidend für die Genauigkeit der Wägeergebnisse.

1. Sicherstellen, dass der Standort der Wägebrücke stabil, erschütterungsfrei und

horizontal ist.

2. Folgende Umweltbedingungen beachten:

– Keine direkte Sonneneinstrahlung

– Kein starker Luftzug

– Keine übermäßigen Temperaturschwankungen

20

Betrieb

PUA-Serie 30290730C

La pagina sta caricando ...

Mettler Toledo PUA series CEU Manuale utente

Questo manuale è adatto anche per

Mettler Toledo PUA series CEU Manuale utente

in altre lingue

Documenti correlati

Altri documenti