Star Micronics TSP552II Manuale utente

THERMAL PRINTER

TSP552II

USER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

Federal Communications Commission

Radio Frequency Interference

Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

For compliance with the Federal Noise Interference Standard, this equipment requires a

shielded cable.

This statement will be applied only for the printers marketed in U.S.A.

Statement of

The Canadian Department of Communications

Radio Interference Regulations

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus set out in the Radio Interference Regulations of the Canadian Department

of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

The above statement applies only to printers marketed in Canada.

CE

Manufacturer’s Declaration of Conformity

EC Council Directive 89/336/EEC of 3 May 1989

This product, has been designed and manufactured in accordance with the International

Standards EN 50081-1/01.92 and EN 50082-1/01.92, following the provisions of the

Electro Magnetic Compatibility Directive of the European Communities as of May 1989.

EC Council Directive 73/23/EEC and 93/68/EEC of 22 July 1993

This product, has been designed and manufactured in accordance with the International

Standards EN 60950, following the provisions of the Low Voltage Directive of the

European Communities as of July 1993.

The above statement applies only to printers marketed in EU.

Trademark acknowledgments

TSP552II: Star Micronics Co., Ltd.

ESC/POS: Seiko Epson Corporation

Notice

without STAR’s express permission is forbidden.

• The contents of this manual are subject to change without notice.

• All efforts have been made to ensure the accuracy of the contents of this manual at the

time of going to press. However, should any errors be detected, STAR would greatly

appreciate being informed of them.

• The above notwithstanding, STAR can assume no responsibility for any errors in this

manual.

©

TABLE OF CONTENTS

1. Outline ..............................................................................................................1

2. Parts Identification and Nomenclature .........................................................2

3. Consumable Parts and AC Adapter ..............................................................4

4. Connecting Cables and AC Adapter..............................................................5

4-1. Connecting the Interface Cable..............................................................5

4-2. Connecting the Peripheral Drive Cable .................................................6

4-3. Connecting the optional AC Adapter.....................................................7

4-4. Turning Power On .................................................................................8

5. Control Panel ...................................................................................................9

5-1. PAPER FEED Switch ............................................................................9

5-2. POWER LED.........................................................................................9

5-3. ERROR LED .........................................................................................9

6. Loading Paper................................................................................................10

6-1. Loading New Roll Paper......................................................................10

6-2. Removing Remaining Paper ................................................................12

7. Command Summary .....................................................................................13

7-1. Star Mode..............................................................................................13

7-2. ESC/POS Mode ...................................................................................17

8. Preventing and Clearing Paper Jams ..........................................................19

8-1. Preventing Paper Jams .........................................................................19

8-2. Removing Paper Jam ...........................................................................19

9. Test Print Method..........................................................................................21

9-1. Producing a Test Print..........................................................................21

9-2. Hexadecimal Dump .............................................................................21

10. Periodical Cleaning .....................................................................................22

10-1.Cleaning the Thermal Head .................................................................22

10-2.Cleaning the Paper Holder ...................................................................22

Appendix A: Specifications...............................................................................95

A-1. General Specifications .........................................................................95

A-2. Print Specifications ..............................................................................95

A-3. Interface ...............................................................................................95

A-4. Power supply........................................................................................96

A-5. Environmental requirements ................................................................96

A-6. Reliability.............................................................................................96

Appendix B: Dip Switch Setting.......................................................................97

B-1. Serial Interface Type............................................................................97

B-2. Parallel Interface Type .........................................................................98

ENGLISH

Appendix C: Interface.....................................................................................100

C-1. Serial Interface ...................................................................................100

C-2. Two-way parallel interface (IEEE1284) ............................................103

C-3. Peripheral Drive Connector ...............................................................106

C-4. Power Connector................................................................................108

Please access the following URL

http://www.star-micronics.co.jp/service/frame_sp_spr_e.htm

for the lastest revision of the manual.

ENGLISH

– 1 –

ENGLISH

1. Outline

This manual explains how to use the thermal printer TSP552II and provides

points to note for safe use and prevention of problems and malfunctions.

Before using the printer, please read this manual thoroughly to ensure its

optimum use.

The major features of the printer are as follows:

1. Prints at high speed (max. 130 mm/sec, 28 lines per second when the line feed

is set to 3.75 mm)

2. Quality print (8 dots/mm) thanks to the high-density line thermal print head.

3. Low noise due to line thermal technology.

4. Logo, coupon, and bar code printing is available.

5. Print density can be adjusted by DIP switches.

6. An auto cutter is provided as standard.

7. The built-in peripheral unit driver enables control of two peripheral units.

8. Considerable ease of paper loading thanks to the paper drop-in structure.

9. The paper drop-in structure makes maintenance easy.

10.The compact size requires only a small installation space.

11.Supports ESC/POS

TM

commands.

– 2 –

ENGLISH

2. Parts Identification and Nomenclature

Control panel

Features LED indica-

tors to indicate printer

status and switches to

operate the printer.

DIP switch

Used to make various

settings.

Lever

Pull down this lever to open

the printer cover.

Switch

Used to turn on/off

power to the printer.

Printer cover

Open this

cover to load

or replace

paper.

Roll paper User’s manual

Power connector

Peripheral drive connector Interface connector

– 3 –

ENGLISH

Choosing a place for the printer

Before actually unpacking the printer, you should take a few minutes to

think about where you plan to use it. Remember the following points

when doing this.

✓ Choose a firm, level surface where the printer will not be exposed to

vibration.

✓ The power outlet you plan to connect to for power should be nearby

and unobstructed.

✓ Make sure that the printer is close enough to your host computer for

you to connect the two.

✓ Make sure that the printer is not exposed to direct sunlight.

✓ Make sure that the printer is well away from heaters and other sources

of extreme heat.

✓ Make sure that the surrounding area is clean, dry, and free of dust.

✓ Make sure that the printer is connected to a reliable power outlet. It

should not be on the same electric circuit as copiers, refrigerators, or

other appliances that cause power spikes.

✓ Make sure that the room where you are using the printer is not too

humid.

– 4 –

ENGLISH

3. Consumable Parts and AC Adapter

When consumable parts have run out, use those specified in the table below.

Make sure that the AC adapter specified in the table is used.

Use of consumable parts or AC adapter which are not specified in the table may

result in damage to the printer, fire or electric shock.

Parts Name Specifications

Roll paper Thermal paper

Width: 80 mm

Outer roll diameter: ø83 mm or less

Core outer diameter: ø18 mm

Core inner diameter: ø12 ±0.5 mm

Recommended paper (Normal type paper)

TF50KS-E2C (Nippon Paper Industries)

PD-150R (Oji Paper Co., Ltd.)

P220AG (Mitsubishi Paper Mills Limited)

Recommended paper (High image stability paper)

PD-160R (Oji Paper Co., Ltd.)

HP220AB-1 (Mitsubishi Paper Mills Limited)

HP220A (Mitsubishi Paper Mills Limited)

AC adapter (Option) Input: 90 to 264 V AC

Output: 24 V DC

Important!

Access the following URL for the information of the recommended paper.

http://www.star-micronics.co.jp/

0

- 1.0

+0.5

0

– 5 –

ENGLISH

4. Connecting Cables and AC Adapter

4-1. Connecting the Interface Cable

Note: Before connecting/disconnecting the interface cable, make sure that

power to the printer and all the devices connected to the printer is

turned off. Also make sure the power cable plug is disconnected from

the AC outlet.

(1)Connect the interface cable to the connector on the rear panel of the printer.

(2)In the case of a serial interface, tighten the connector screws. In the case of a

parallel interface, fasten the connector clasps.

(3)Pass the interface cable through the hole provided at the bottom of the printer

cover, then place the printer in position.

Note: Make sure that the interface cable is passed through the hole. Failure

to do so may cause the cable to be squashed by the printer, resulting in

damage to the cable.

Serial interface cable

Parallel interface cable

– 6 –

ENGLISH

4-2. Connecting the Peripheral Drive Cable

Note: Before connecting/disconnecting the peripheral drive cable, make

sure that power to the printer and all the devices connected to the

printer is turned off. Also make sure the power cable plug is discon-

nected from the AC outlet.

(1)Connect the peripheral drive cable to the connector on the rear panel of the

printer, and pass it through the cable hole provided at the bottom of the printer

cover.

Note: Make sure that the peripheral drive cable is passed through the hole.

Failure to do so may cause the cable to be squashed by the printer,

resulting in damage to the cable.

– 7 –

ENGLISH

4-3. Connecting the optional AC Adapter

Note: Before connecting/disconnecting the AC adapter, make sure that

power to the printer and all the devices connected to the printer is

turned off. Also make sure the power cable plug is disconnected from

the AC outlet.

(1)Connect the AC adapter to the power cable.

Note: Use only the standard AC adapter and power cable.

(2)Cut off the blank cable hole on the printer cover using nippers.

(3)Pass the AC adapter through the hole, and connect it to the connector on the

printer.

Note: Make sure that the AC cable is passed through the hole. Failure to do

so may cause the cable to be squashed by the printer, resulting in

serious danger.

(4)Insert the power cable plug into an AC outlet.

– 8 –

ENGLISH

Power switch

4-4. Turning Power On

Make sure that the AC adapter has been connected as described in 4-3.

(1)Set the power switch located on the side of the printer to on.

The POWER lamp on the control panel will light up.

Important!

We recommend that you unplug the printer from the power outlet

whenever you do not plan to use it for long periods. Because of this, you

should locate the printer so that the power outlet it is plugged into is

nearby and easy to access.

– 9 –

ENGLISH

5. Control Panel

5-1. PAPER FEED Switch

Each time this switch is pressed, the paper feeds on line. When it is kept

depressed, the paper feeds continuously.

Note: This switch will be ineffective if no paper is loaded.

5-2. POWER LED

This LED lights up when the power switch is set to on and power is supplied to

the printer.

5-3. ERROR LED

This LED lights up or blinks when any of the following errors occurs.

Error LED

No paper (paper end) is detected.

Printer cover is open.

Lights steadily.

Printing is interrupted due to excessively hot thermal head.

Abnormal power

Paper near end is detected. Blinks.

– 10 –

ENGLISH

6. Loading Paper

6-1. Loading New Roll Paper

(1)Set the power switch to off to turn off power to the printer.

(2)Pull the lever toward you to open the printer cover.

Note: Make sure that the lever is pulled until it stops at the stopper. If the lever

is not pulled up to the stopper, the printer cover may not open.

(3)Peel the adhesive end off the paper.

Note: Make sure that the entire adhesive area is removed, since no printing

can be performed on that area.

(4)Position the paper in the direction as shown below and place it into the paper

holder gently.

Note 1: Make sure that the paper is not deformed. If a roll paper like those

shown below is used, a malfunction may result.

Note 2: If the paper sags as shown below after it has been loaded into the

paper holder, make the paper taut.

Paper holder

– 11 –

ENGLISH

(5)Make sure that the paper is positioned straight, then close the printer cover

gently.

Note 1: Make sure that the paper is positioned straight. If the printer cover

is closed with the paper skewed as shown below, a paper jam may

result.

Note 2: Lock the printer cover by pressing on the center of the cover

(indicated by an arrow in the figure below). If any part of the cover

other than the center is pressed, the cover may not be locked

properly. This may sometimes disables printing.

Paper

– 12 –

ENGLISH

(6)Set the power switch to on to turn on power to the printer. Make sure that the

ERROR LED is not lit.

Note: While the ERROR LED is lit, the printer will not accept any commands

such as the print command, so make sure that the printer cover is locked

properly.

(7)Issue the cut command to cut off the end of the paper.

6-2. Removing Remaining Paper

(1)Set the power switch to off to turn off power to the printer.

(2)Pull the lever toward you to open the printer cover.

Note: Make sure that the lever is pulled until it stops at the stopper. If the lever

is not pulled up to the stopper, the printer cover may not open.

(3)Remove the remaining paper.

– 13 –

ENGLISH

7. Command Summary

This printer supports two different command modes: the Star mode and the ESC/

POS mode.

This chapter provides you with all of the commands supported by this printer.

Important!

Access the following URL for the latest version of this manual and for

updates on supported commands: http://www.star-micronics.co.jp/

service/sp_sup_e.htm

7-1. Star Mode

Commands to Select Characters

Control codes

Hexadecimal

Function

codes

<ESC> “R” n 1B 52 n Select international character set

<ESC> <GS> t n 1B 1D 74 n Select character table

<ESC> “/” “1” 1B 2F 31

Select slash zero

<ESC> “/” <1> 1B 2F 01

<ESC> “/” “0” 1B 2F 30

Select normal zero

<ESC> “/” <0> 1B 2F 00

<ESC> “b” n1 n2 n3 n4 1B 62 n1 n2 n3 n4 Select bar code printing

d1 ... <RS> d1 ... 1E

<ESC> “M” 1B 4D Select 12-dot pitch printing

<ESC> “p” 1B 70 Select 14-dot pitch printing

<ESC> “P” 1B 50 Select 15-dot pitch printing

<ESC> “:” 1B 3A Select 16-dot pitch printing

<ESC> <SP> n 1B 20 n Set character spacing

<SO> 0E Sets the printing magnified double in

character width.

<DC4> 14 Resets the printing magnified in

character width.

<ESC> “W” n 1B 57 n

Sets the magnification rate in character width.

<ESC> <SO> 1B 0E Sets the printing magnified double in

character height.

<ESC> <DC4> 1B 14 Resets the printing magnified in character

height.

<ESC> “h” n 1B 68 n

Sets the magnification rate in character height

.

<ESC> “

–

” “1” 1B 2D 31

Select underlining

<ESC> “

–

” <1> 1B 2D 01

– 14 –

ENGLISH

Control codes

Hexadecimal

Function

codes

<ESC>“

–

” “0” 1B 2D 30

Cancel underlining

<ESC> “

–

” <0> 1B 2D 00

<ESC> “

_

” “1” 1B 5F 31

Select overlining

<ESC> “

_

” <1> 1B 5F 01

<ESC> “

_

” “0” 1B 5F 30

Cancel overlining

<ESC> “

_

” <0> 1B 5F 00

<ESC> “4” 1B 34 Select highlight printing

<ESC> “5” 1B 35 Cancel highlight printing

<SI> 0F Inverted printing

<DC2> 12 Cancel inverted printing

<ESC> “

E

” 1B 45 Select emphasized printing

<ESC> “

F

” 1B 46 Cancel emphasized printing

Commands to Set the Page Format

Control codes

Hexadecimal

Function

codes

<ESC> “C” n 1B 43 n Set page length in lines

<ESC> “C” <0> n 1B 43 00 n Set page length in inches

<ESC> “N” n 1B 4E n Set bottom margin

<ESC> “O” 1B 4F Cancel bottom margin

<ESC> “l” n 1B 6C n Set left margin

<ESC> “Q” n 1B 51 n Set right margin

Commands to Move the Print Position

Control codes

Hexadecimal

Function

codes

<LF> 0A Line feed

<ESC> “a” n 1B 61 n Feed paper n lines

<FF> 0C Form feed

<HT> 09 Horizontal tab

<VT> 0B Vertical tab

<ESC> “z” “1” 1B 7A 31

Set line spacing to 4 mm

<ESC> “z” <1> 1B 7A 01

<ESC> “0” 1B 30 Set line spacing to 3 mm

– 15 –

ENGLISH

Control codes

Hexadecimal

Function

codes

<ESC> “J” n 1B 4A n One time n/4 mm feed

<ESC> “I” n 1B 49 n One time n/8 mm feed

<ESC> “B” n1 n2 ... <0> 1B 42 n1 n2 ... 00 Set vertical tab stops

<ESC> “D” n1 n2 ... <0> 1B 44 n1 n2 ... 00 Set horizontal tab stops

<ESC> <GS> “A” n1 n2 1B 1D 41 n1 n2 Absolute position setting

<ESC> <GS> “R” n1 n2 1B 1D 52 n1 n2 Relative position setting

<ESC> <GS> “a” n 1B 1D 61 n Alignment

Commands to Print Dot Graphics

Control codes

Hexadecimal

Function

codes

<ESC> “K” n <0> 1B 4B n 00 m1 m2 Print normal density graphics

m1 m2 ... ...

<ESC> “L” n1 n2 1B 4C n1 n2 m1 m2 Print high density graphics

m1 m2 ... ...

<ESC> “k” n <0> m1 ... 1B 6B n 00 m1 ... Print fine density graphics

<ESC> “X” n1 n2 1B 58 n1 n2 Print fine density graphics

<ESC> <FS> “p” n m 1B 1C n m Print NV bit image

Commands to Print Download Characters

Control codes

Hexadecimal

Function

codes

<ESC> “&” “1” “1” 1B 26 31 31 n

n m1 m2 ... m48 m1 m2 ... m48

Define download character

<ESC> “&” <1> <1> 1B 26 01 01

n m1 m2 ... m48 n m1 m2 ... m48

<ESC> “&” “1” “0” n 1B 26 31 30 n

Delete a download character

<ESC> “&” <1> <0> n 1B 26 01 00 n

<ESC> “%” “1” 1B 25 31

Enable download character set

<ESC> “%” <1> 1B 25 01

<ESC> “%” “0” 1B 25 30

Disable download character set

<ESC> “%” <0> 1B 25 00

<ESC> <GS> “*” xy 1B 1D 2A 78 79 Definition of download bit image

<ESC> <GS> “/” m 1B 1D 2F 6D Printing of download bit image

– 16 –

ENGLISH

Commands to Control Peripheral Devices

Control codes

Hexadecimal

Function

codes

<ESC> <BEL> n1 n2 1B 07 n1 n2 Define drive pulse width for peripheral device #1

<BEL> 07 Control peripheral device #1

<FS> 1C Control peripheral device #1 immediately

<EM> 19 Control peripheral device #2 immediately

<SUB> 1A Control peripheral device #2 immediately

Commands to Control Auto Cutter

Control codes

Hexadecimal

Function

codes

<ESC> “d” n 1B 64 n Partial-cut command to the auto cutter

Other Commands

Control codes

Hexadecimal

Function

codes

<CAN> 18 Cancel last line & Initialize printer immediately

<DC3> 13 Deselect printer

<DC1> 11 Set select mode

<RS> 1E Beep the buzzer

<ESC> “@” 1B 40 Initialize printer

<ENQ> 05 Enquiry (Status inquiry)

<EOT> 04 Near end status inquiry

1B 3F 0A 00 Reset printer hardware (Perform test print)

<ESC> “8” n1 n2 1B 38 n1 n2 Resisters a logo pattern

<ESC> “9” n1 n2 1B 39 n1 n2 Prints a logo pattern

La pagina sta caricando ...

Star Micronics TSP552II Manuale utente

Star Micronics TSP552II Manuale utente

in altre lingue

Documenti correlati

Altri documenti