Star Micronics SLIP SP298 SERIES Manuale utente

SLIP PRINTER

SP298 SERIES

USER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

Federal Communications Commission

Radio Frequency Interference

Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class A dig-

ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-

able protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful interfer-

ence to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference

at his own expense.

This statement will be applied only for the equipments marketed in U.S.A.

FCC WARNING

Changes or modiﬁcations not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

For compliance with the Federal Noise Interference Standard, this equipment requires a

shielded cable.

For RF interference suppression, if a ferrite core is provided with this device, afﬁx it to the

interface cable.

Statement of

The Canadian Department of Communications

Radio Interference Regulations

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

The above statement applies only to printers marketed in Canada.

Trademark acknowledgments

SP298, AutoSide Loading

: Star Micronics Co. Ltd.

ESC/POS, TM-295, TM-290

: Seiko Epson Corporation

Notice

mission, is strictly forbidden.

• The contents of this manual are subject to change without notice.

• All efforts have been made to ensure the accuracy of the contents of this manual at the time of printing. However,

should any errors be found, STAR would greatly appreciate being informed of them.

• The above notwithstanding, STAR can assume no responsibility for any errors in this manual.

TABLE OF CONTENTS

Chapter 1: Printer Setup ..............................................................................1

Choosing a place for the printer ..................................................1

Unpacking the printer ..................................................................2

Removing the protective materials ..............................................2

General guide ..............................................................................3

Removing the printer cover .........................................................4

Installing the ribbon cassette .......................................................4

Removing the ribbon cassette ......................................................6

Connecting to a power outlet and turning power on and off .......6

Connecting to your host computer ..............................................8

Connecting to a peripheral unit .................................................10

Inserting the paper into the printer ............................................11

AutoSide Loading™ ..................................................................12

Chapter 2: Control Panel Operations .......................................................14

Indicator lights ...........................................................................14

Buttons ......................................................................................15

Producing a test print .................................................................15

Adjusting the dot alignment ......................................................15

Hexadecimal dump ....................................................................17

Errors .........................................................................................18

Chapter 3: Command Summary ...............................................................20

Star Mode Commands ...............................................................20

ESC/POS Mode Commands (TM-295 emulation).....................26

ESC/POS Mode Commands (TM-290 emulation).....................28

Appendix A: Specifications ..........................................................................120

Appendix B: Making DIP Switch Settings..................................................125

Appendix C: Memory Switch Settings ........................................................130

Appendix D: Interface ..................................................................................131

Appendix E: Peripheral Unit Driver Circuit..............................................137

Please access the following URL

http://www.star-m.jp/eng/dl/dl02.htm

for the latest revision of the manual.

ENGLISH

1

ENGLISH

Chapter 1: Printer Setup

This chapter contains important information on setting up your printer. Be sure

to read this chapter carefully before using the printer for the first time. In this

chapter you will learn about:

❏

Choosing a place for the printer

❏

Unpacking and setting up the printer

❏

Installing the ribbon cassette

❏

Connecting to a host computer

❏

Inserting paper

Choosing a place for the printer

Before actually unpacking the printer, you should take a few minutes to think

about where you plan to use it. Remember the following points when doing this.

✓

Choose a ﬁrm, level surface where the printer will not be exposed to

vibration.

✓

The power outlet you plan to connect to for power should be nearby and

unobstructed.

✓

Make sure that the printer is close enough to your host computer for you to

connect the two.

✓

Make sure that the printer is not exposed to direct sunlight.

✓

Make sure that the printer is well away from heaters and other sources of

extreme heat.

✓

Make sure that the surrounding area is clean, dry, and free of dust.

✓

Make sure that the printer is connected to a reliable power outlet. It should

not be on the same electric circuit as copiers, refrigerators, or other

appliances that cause power spikes.

✓

Use a power outlet that matches the power rating noted on the label afﬁxed

to the bottom of your printer.

✓

Make sure that the room where you are using the printer is not too humid.

2

ENGLISH

Unpacking the printer

Check to make sure that the carton contains each of the items shown in the

following illustration.

If anything is missing, contact the dealer where you bought the printer and ask

them to supply the missing part. Note that it is a good idea to keep the original

box and all the packing materials just in case you need to pack the printer up

again and send it somewhere at a later date.

Removing the protective materials

Four protective materials are inserted into the printer to protect components

during shipping. Before using the printer, be sure to remove all protective

materials as shown in the illustration.

Printer

Ribbon cassette

User’s Manual

Ferrite core

Fastener

tape

3

ENGLISH

General guide

The following illustrations describe the major components, buttons, and

connectors of your printer.

Printer cover

Protects internal components.

Control panel

Three indicators show

the printer status, and

two switches provide

control over printer

functions.

Power switch

Turns printer

power on and off.

Document table

Supports the paper fed

into the printer.

For connection

to a host computer.

For connection of the AC adapter.

Never unplug the AC adapter

while the printer is on.

Interface connector

AC adapter cable connector

Peripheral unit connector cover

Covers a modular jack for

connection of a cash drawer or

other peripheral.

Do not connect a telephone line

to this connector.

4

ENGLISH

Removing the printer cover

❏

Push straight up on the ridged locations on the sides of the printer cover to

remove it from the printer.

❏

To replace the cover, slide it back down into position. Gently press down on

the cover until you hear it click securely into place.

Installing the ribbon cassette

❏

Make sure that the printer’s paper release is activated (the paper is not held

in place by the paper feed roller). If it cannot be determined whether or not

the paper release is activated, turn on the printer and check if the

RELEASE

indicator on the control panel is lit. If the indicator is not lit,

press the

RELEASE

button until the indicator lights up.

❏

Make sure that the printer is turned off and unplugged from its power

outlet.

❏

Remove the printer cover.

❏

Remove the ribbon cassette from its packaging, and turn its knob in the

direction indicated by the arrow to take up any slack in the ribbon.

Printer cover

5

ENGLISH

❏

Holding the ribbon cassette so that the ribbon is facing down, install the

cassette into the slip printer as shown in the illustration.

❏

Press gently but ﬁrmly on the cassette until it snaps securely into place.

❏

Rotate the knob on the cassette again to take up any slack.

❏

Replace the printer cover.

Important!

Make sure that the ribbon is not twisted before installing the ribbon cassette.

Otherwise, the ribbon may become jammed in the printer and damage the

ribbon rollers.

In addition, if the ribbon becomes twisted after installation, remove the ribbon

cassette, untwist the ribbon, and then reinstall the cassette.

<Correct: Ribbon is not twisted> <Incorrect: Ribbon is twisted>

6

ENGLISH

Removing the ribbon cassette

Use the following procedure to remove the ribbon cassette from the slip printer

when you want to replace it with a new one.

❏

Make sure that the printer is turned off and unplugged from its power

outlet.

❏

Remove the printer cover.

❏

Grasping the ribbon cassette as shown, gently pull it away from the printing

mechanism.

❏

Use the procedure under “Installing the ribbon cassette” on page 4 to install

a new cassette.

Connecting to a power outlet and turning power on and off

❏

Plug the AC adapter that comes with the printer into the printer’s AC

adapter cable connector.

❏

Connect a three-prong grounded power cord to the power cord connector of

the AC adapter.

Note:

The printer does not come with a power cord, so you must provide one yourself.

7

ENGLISH

❏

Plug the other end of the power cord to a standard household wall outlet.

❏

Use the power switch on the left side of the printer to turn power on and off.

Important!

We recommend that you unplug the printer from the power outlet whenever you

do not plan to use it for long periods. Because of this, you should locate the

printer so that the power outlet it is plugged into is nearby and easy to access.

At this point you may want to perform a test of the printer to make sure it is

working properly. See page 15 for details on how to test the printer.

8

ENGLISH

Connecting to your host computer

The computer sends data to the printer through a cable to the printer’s interface

(Serial Interface Connector Type: D-sub 25-pin or Parallel Interface Connector

Type: 36-pin Centronics compatible). This printer does not come with a cable,

so it is up to you to obtain one that suits your needs.

Important!

• The following instructions apply to the cable that is used with an IBM-

compatible personal computer. Note that they do not apply to all types of

computers and cables. If you are unsure about what type of cable you should

use to connect with your computer, consult your dealer.

• Make sure that the printer is turned off and unplugged from the AC outlet and

that the computer is turned off before connecting them.

❏

Afﬁx the larger ferrite core onto the cable as shown in the illustration

below.

Ferrite core (28 mm diameter)

Serial Interface

Cable

9

ENGLISH

Pass the fastener through the ferrite core.

Loop the fastener around the cable and lock it. Use scissors to cut off any

excess.

For a serial cable:

❏

Plug one end of the serial cable into the serial port of your computer, and

the other end of the cable into the socket on the back of the printer. Secure

both connectors in place with the screws that are provided.

For a parallel cable:

❏

Attach a ferrite core in the same way that one is attached to a serial cable.

❏

Plug one end of the parallel cable into the parallel port of your computer.

The parallel port should be labeled “Printer”, “Parallel”, “PRN”, “LPT1” or

something similar.

❏

Plug the other end of the parallel cable into the socket on the side of the

printer and secure it in place with the clips.

5 cm

maximum

Fastener

Pull and cut

10

ENGLISH

Connecting to a peripheral unit

You can connect a peripheral unit to the printer using a modular plug. The

following describes how to install the ferrite core and make the actual

connection. See “Modular plug” on page 137 for details about the type of

modular plug that is required. Note that this printer does not come with a

modular plug or wire, so it is up to you to obtain one that suits your needs.

Important!

Make sure that the printer is turned off and unplugged from the AC outlet and

that the computer is turned off before making connections.

❏

Afﬁx the smaller ferrite core onto the modular wire as shown in the

illustration below.

Pass the fastener through the ferrite core.

Ferrite core (20 mm diameter)

Connector

Cable

5 cm

maximum

Fastener

11

ENGLISH

Loop the fastener around the cable and lock it. Use scissors to cut off any

excess.

❏

Plug one end of the modular cable into the modular jack of the peripheral.

❏

Remove the modular jack cover from the back of the printer and plug the

other end of the modular cable into the jack of the printer.

Inserting the paper into the printer

Use only the specified type of paper for this printer. Do not use inappropriate

types of paper, or it could cause malfunction or damage of the printer.

The following procedure describes how to print on paper. Before trying to print,

be sure to install a ribbon cassette into the printer using the procedure under

“Installing the ribbon cassette” on page 4.

❏

Make sure that the printer is plugged in and turned on.

❏

Check that the

RELEASE

indicator on the control panel is lit. If the

indicator is not lit, press the

RELEASE

button until the indicator lights up.

Important!

Insertion and removal of paper should be done only when the printer is

released condition (the paper is not held by paper feed roller).

Pull and cut

12

ENGLISH

❏

Place a piece of the paper onto the printer’s document table and slide its

right edge into the printer. Printing will be performed on the side of the

paper that is facing up (the one you can see), starting from the top of the

paper.

Important!

Do not use wrinkled or curled paper. In case of multiple paper, neatly align the

sheets.

Though paper can be inserted either from the front or side of the printer, front

paper insertion may result in paper jams, depending on the condition of the paper.

Because of this, it is recommended that you always insert paper from the side.

AutoSide Loading™

This printer is equipped with paper sensors, so you do not have to perform any

special procedure to align the location from which printing should start. Simply

insert the paper into the printer and the sensor locates the top of the paper. The

paper will be moved automatically into position for printing.

Important!

When inserting the paper into the printer, make sure that there are at least 3 cm

between the top edge of the paper and the print start position mark on the

printer. Otherwise the paper sensor may not be able to correctly locate the top

of the paper.

At least 3 cm

Print start position mark

13

ENGLISH

❏

Push the right edge of the paper into the printer until it stops. At that time,

the

PAPER OUT

indicator will go out, and the printer mechanism will

automatically align the paper for printing from the top.

❏

Send data from your host computer to be printed on the paper.

❏

After printing, press the

RELEASE

button to automatically release the

paper.

14

ENGLISH

Chapter 2: Control Panel Operations

The control panel gives you some push-button control over the slip printer

operation. It also includes indicator lights, which tell you the current status of

the printer at a glance.

Indicator lights

The following table describes the meaning of indicator lights when it is on, off,

or flashing.

Indicator Light Off On Flashing

POWER

Power off Power on

Dot Alignment Adjust

Mode

PAPER OUT

Paper inserted No paper Insert paper prompt

RELEASE

Slip paper engaged Slip paper released Mechanical error

FORWARD

POWER

RELEASE

PAPER

OUT

REVERSE

RELEASE

15

ENGLISH

Buttons

The following table describes the function of the three control buttons of the

control panel.

Producing a test print

The following procedure can be used at any time to test the printer.

❏

Turn on the printer and insert a piece of paper (page 6, 11).

❏

Turn off printer power.

❏

While holding down

RELEASE

, turn printer back on. Keep

RELEASE

depressed for a few moments until the printer beeps and the printer test

print starts.

The printer test will continue until it reaches the end of the paper.

Adjusting the dot alignment

You may never have to use the procedure described in this section, but after you

have been using your printer for some time you may find that the dots of some

graphics do not align correctly. For example, what should look like:

may come out looking like one of the following:

Button Description

FORWARD

Feeds the slip paper forward, toward the back of the printer. One

press feeds one line, holding down performs continuous feed.

REVERSE

Feeds the slip paper back, toward the front of the printer. One press

feeds one line, holding down performs continuous feed.

RELEASE

Activates the printer’s paper release (the paper is not held in place by

the paper feed roller).

Clears recoverable errors.

or like this

16

ENGLISH

This is caused when mechanical parts of the printer get out of alignment. This

happens only rarely and you may never experience it at all throughout the life

of the printer. If you do have problems, use the following procedure to correct it.

❏

Turn on the printer and insert a piece of paper.

❏

Turn off printer power.

❏

While holding down the control panel’s

FORWARD

and

REVERSE

buttons, turn the printer back on to enter the Dot Alignment Adjust Mode,

which is indicator by a ﬂashing

POWER

indicator ﬂashes.

Entering the Dot Alignment Adjust Mode causes seven blocks to be printed,

each of which indicates a dot alignment setting, as shown below. An asterisk

to the left of the blocks indicates which block is currently selected.

❏

Use

FORWARD

to specify the block that appears to have the best aligned

characters. Press

FORWARD

once to specify the ﬁrst block, twice to

specify the second block, and so on up to seven times to specify the seventh

block.

Warning beep will sound if you press

FORWARD

more than seven times.

❏

After specifying a block, press

REVERSE

to register your selection and

exit the Dot Alignment Adjust Mode.

17

ENGLISH

The dots alignment adjustment setting you selected is stored in printer memory

and a pattern is printed using the selected setting followed by the message

“Adjust Complete!” The printer ejects the paper after printing is complete.

Note:

You setting is not registered if you turn off printer power before pressing

REVERSE to exit the Dot Alignment Adjust Mode.

If a paper feed error occurs during this mode, the printer ejects the paper and

this mode is cancelled.

Hexadecimal dump

This procedure prints in hexadecimal format all codes (character codes and

control codes) that are sent to the printer by the computer. The printer does not

execute any control codes (such as 0A - linefeed), it just prints them out. The

hexadecimal dump is useful when you are writing programs for printer control.

❏

Turn on the printer and insert a piece of paper.

❏

Turn off printer power.

❏

While holding down the control panel’s

FORWARD

buttons, turn the

printer back on to enter the Hex Dump Mode.

❏

To exit the Hex Dump Mode, turn the printer off.

Note:

The printer will not responde to any commands you send it while it is in the

Hex Dump Mode.

La pagina sta caricando ...

Star Micronics SLIP SP298 SERIES Manuale utente

Questo manuale è adatto anche per

Star Micronics SLIP SP298 SERIES Manuale utente

in altre lingue

Documenti correlati

Altri documenti