Worx LANDROID WG796E Original Instructions Manual

P02

P16

P30

P44

P58

Lawn Mowing Robot

Roboter-Rasenmäher

Robot de fauchage à pelouse

Robot tosaerba

Robot za košnjo trave

EN

D

F

I

SL

WG796E

Lawn Mowing Robot EN

2

TABLE OF CONTENTS

1. Product Safety

1.1 Safety Warnings for your lawnmower

1.2 Information on the Landroid

®

M

2. Component list

3. Understanding Your Landroid

®

M

3.1 How does my Landroid

®

M know what to mow?

3.2 How does my Landroid

®

M know where to go?

A. Finding the charging base

B. Rain sensors

C. Sensing the boundary wire

D. Starting and stopping while mowing

3.3 How big an area can my Landroid

®

M mow?

3.4 How efﬁciently will my Landroid

®

M mow the grass?

4. Smart phone control

5. Boundary Wire Basics

5.1 Pegging the Boundary Wire

5.2 Burying the Boundary Wire

5.3 Joining the Boundary Wire

5.4 Turn on and test installation

6. Software update

7. Maintenance

7.1 Keep it Sharp

A. Rotate and Flip the Blades

B. Replace the Blades

7.2 Keep it Clean

A. Cleaning the Body

B. Cleaning the Underside

C. Clean the contact pins and the charging strips

7.3 Battery Life

7.4 Winter Hibernation

7.5 Replacing the battery

3

5

6

8

9

10

11

12

13

14

ORIGINAL INSTRUCTIONS

Lawn Mowing Robot EN

3

1. Product Safety

1.1 Safety warnings for your lawnmower

WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions

may result in electric shock, ﬁre and/or serious injury.

Carefully read the instructions for the safe operation of the machine.

Save all warnings and instructions for future reference.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• The appliance is only to be used with the power supply unit provided with the appliance.

IMPORTANT

READ CAREFULLY BEFORE USE

KEEP FOR FUTURE REFERENCE

SAFE OPERATION PRACTICES

Training

a) Read the instructions carefully. Make sure you understand the instructions and be familiar with the controls and the

proper use of the appliance.

b) Never allow people unfamiliar with these instructions or children to use the appliance. Local regulations can restrict the

age of the operator.

c) The operator or user is responsible for accidents or hazards occurring to other people or their property.

Preparation

a) Ensure the correct installation of the boundary wire as instructed.

b) Periodically inspect the area where the appliance is to be used and remove all stones, sticks, wires, bones, and other

foreign objects.

c) Periodically visually inspect to see that the blades, blade bolts and cutter assembly are not worn or damaged. Replace

worn or damaged blades and bolts in sets to preserve balance.

d) On multi-spindle appliances, take care as rotating one blade can cause other blades to rotate.

e) WARNING! The lawnmower shall not be operated without the guard in place.

OPERATION

1. GENERAL

a) Never operate the appliance with defective guards, or without safety devices, for example deﬂectors, in place;

b) Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times;

c) Never pick up or carry an appliance while the motor is running;

d) Operate the disabling device from the appliance;

– Before clearing a blockage;

– Before checking, cleaning or working on the appliance;

e) It is not permitted to modify the original design of robotic lawnmower. All modiﬁcations are made at your own risk.

f) Start robotic lawnmower according to the instructions. When the power key is switched on, make sure you keep your

hands and feet away from the rotating blades. Never put your hands and feet under the mower.

g) Never lift up robotic lawnmower or carry it when the power key is switched on.

h) Do not let persons who do not know how robotic lawnmower works and behaves use the mower.

i) Do not put anything on top of robotic lawnmower or its charging station.

j) Do not allow robotic lawnmower to be used with a defective blade disc or body. Neither should it be used with defective

blades, screws, nuts or cables.

k) Always switch off robotic lawnmower when you do not intend to use the mower. Robotic lawnmower can only start

when the power key is switched on and the correct PIN code has been entered.

2. ADDITIONALLY WHEN THE APPLIANCE IS OPERATING AUTOMATICALLY

a) Do not leave the machine to operate unattended if you know that there are pets, children or people in the vicinity.

MAINTENANCE AND STORAGE

WARNING! When turning the mower upside down, the power key must always be switched off.

The power key should be switched off during all work on the mower’s underframe, such as

cleaning or replacing the blades.

Lawn Mowing Robot EN

4

a) Keep all nuts, bolts and screws tight to be sure the appliance is in safe working condition;

b) Inspect the robotic lawnmower each week and replace worn or damaged parts for safety;

c) Check especially that the blades and blade disc are not damaged. Replace all blades and screws at the same time if

necessary so that the rotating parts are balanced.

d) Ensure that only replacement cutting means of the right type are used;

e) Ensure that batteries are charged using the correct charger recommended by the manufacturer. Incorrect use may result

in electric shock, overheating or leakage of corrosive liquid from the battery;

f) In the event of leakage of electrolyte ﬂush with water/neutralizing agent, seek medical help if it comes into contact with

the eyes etc;

g) Servicing of the appliance should be according to manufacturers instructions.

Transport

The original packaging should be used when transporting robotic lawnmower over long distances.

To safely move from or within the working area:

a) Press the STOP button to stop the mower.

b) You select the four digit PIN code when you start the mower for the ﬁrst time.

c) Always switch off robotic lawnmower if you intend to carry the mower.

d) Carry the mower by the handle at the rear under the mower. Carry the mower with the blade disc away from the body.

Safety warnings for battery pack

a) Do not dismantle, open or shred cells or battery pack.

b) Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or drawer

where they may short-circuit each other or be short-circuited by conductive materials. When battery

pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal

objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause

burns or a ﬁre.

c) Do not expose battery pack to heat or ﬁre. Avoid storage in direct sunlight.

d) Do not subject battery pack to mechanical shock.

e) In the event of battery leaking, do not allow the liquid to come into contact with the skin or eyes.

If contact has been made, wash the affected area with copious amounts of water and seek medical

advice.

f) Seek medical advice immediately if a cell or battery pack has been swallowed.

g) Keep battery pack clean and dry.

h) Battery pack gives its best performance when it is operated at normal room temperature (20°C ±

5°C).

i) When disposing of battery packs, keep battery packs of different electrochemical systems separate

from each other.

j) Recharge only with the charger speciﬁed by WORX. Do not use any charger other than that

speciﬁcally provided for use with the equipment. A charger that is suitable for one type of battery pack may

create a risk of ﬁre when used with another battery pack.

k) Do not use any battery pack which is not designed for use with the equipment.

l) Keep battery pack out of the reach of children.

m) Retain the original product literature for future reference.

n) Dispose of properly.

Lawn Mowing Robot EN

5

1.2 Information on the Landroid

®

M

WARNING - Robotic lawnmower can be dangerous if incorrectly used.

Read through the Operator’s manual carefully and understand the content before using your robotic

lawnmower.

WARNING - Keep a safe distance from the machine when operating.

WARNING - Operate the disabling device before working on or lifting the machine.

WARNING - Do not ride on the machine.

Do not burn

Batteries may enter water cycle if disposed improperly, which can be hazardous for ecosystem. Do not

dispose of waste batteries as unsorted municipal waste.

Batteries should be recycled. Do not dispose of batteries, Return exhausted batteries to your local collection

or recycling point.

Do not wash the machine with a high pressure washer

Waste electrical products must not be disposed of with household waste. Please recycle where facilities

exist. Check with your local authorities or retailer for recycling advice.

Lawn Mowing Robot EN

6

2. Component List

6

8

75

9

10

11

12

13

23

2221

17

19

16

18

3

4

2

1

25

20

24

15

14

Lawn Mowing Robot EN

7

1. HANDLE BAR

2. LOW VOLTAGE CABLE

3. CONTACT PINS

4. CHARGING BASE

5. CHARGING STRIP

6. DISPLAY WINDOW

7. CONTROL PANEL COVER

8. STOP BUTTON

9. RAIN SENSOR

10. REAR DRIVING WHEEL

11. HANDLE

12. BATTERY PACK

13. BLADE TURNING DISC

14. CUTTING BLADE

15. FRONT WHEEL

16. START KEY

17. DISPLAY

18. KEYPAD

19. ON/OFF KEY

20. POWER ADAPTOR

21. BOUNDARY WIRE

22. WIRE PEGS

23. CHARGING BASE FIXING NAILS

24. BOUNDARY WIRE DISTANCE GAUGE

25. HEX KEY

Lawn Mowing Robot EN

8

3. Understanding Your Landroid

®

M

We would like to congratulate you on your new purchase of the Landroid

®

M and entering into the care-free life of automatic

mowing. In the following, we would like to help you better understand how your Landroid

®

M thinks.

3.1 How does my Landroid

®

M know what to mow?

The Landroid

®

M chooses its direction at random. It will make sure your entire lawn is evenly mowed without leaving

behind any unattractive mowing paths (See Fig. A).

A

Lawn Mowing Robot EN

9

3.2 How does my Landroid

®

M

know where to go?

Your Landroid

®

M is capable of doing things on its own. The

Landroid

®

M knows when it needs to go to its Charging Base (4)

to charge, can sense when it is raining, can stop itself if it senses

a problem, and knows to stop, draw back, and then turn around

when it bumps into something blocking its path or other object. The

Landroid

®

M will also automatically stop its Blade Turning Disc (13)

from rotating if it is lifted off the ground to prevent an accident.

A. Finding the charging base

When your Landroid

®

M needs to recharge, it will stop mowing and

follow the Boundary Wire (21) in an anti-clockwise direction back

to its Charging Base. Landroid

®

M is pre-programmed to mow the

grass near the boundary wire once a week. If you want to mow the

grass near the boundary wire at other times, open the panel cover,

press the home button and close the panel cover. Landroid

®

M will

stop mowing, locate the boundary wire and mow the grass near the

boundary wire while it locates the charging station . We suggest you

use this function when the battery power is more than 75%. You can

check the battery power in the display.

B. Rain sensors

The Landroid

®

M is fitted with a Rain Sensor (9) that will detect

rain drops and tell the Landroid

®

M to stop mowing and follow the

Boundary Wire back to its Charging Base (See Fig. B )

The Landroid

®

M is programmable to have a delay start function

(0 – 180 mins) when it rains. When the rain sensors are wet, the

Landroid

®

M returns to its docking station. Only when the rain sensors

become dry will the Landroid

®

M begin the delay start countdown or

return to mowing immediately. See the Programming and Troubleshooting Guide for more details.

C. Sensing the boundary wire

The Landroid

®

M always obeys the border set by the Boundary Wire and uses two sensors at its front to sense when it is

getting close(See Fig. C). Before changing direction, the Landroid

®

M will overrun the Boundary Wire up to 20 cm*.

*This is the recommended distance. Use the provided distance gauge to ensure proper installation.

D. Starting and stopping while mowing (See Fig. D,E)

If you would like to command the Landroid

®

M to stop mowing, then simply press the STOP button (8) on top of the mower.

To start mowing open the Control Panel Cover, press the ON/OFF key and input the PIN code, then press start key and

close the panel cover.

B

C

DD

E

Lawn Mowing Robot EN

10

If the Landroid

®

M senses that something is wrong, it will display a fault message on the Display (17), and will turn itself off

if it does not receive any input from the user within 20 min (for information on fault messages refer to the Programming

and Troubleshooting Guide).

To resume:

Scene 1: STOP –Auto Shutdown after 20 mins

• Open the Control Panel Cover

• Press the ON/OFF Key (19) to ON

• Press 0 key to correct the problem

• Press START button again and Close the Control Panel Cover

• Now the Landroid

®

M will begin to mow!

Scene 2: STOP– Without Auto Shutdown

• Open the Control Panel Cover

• Press 0 key to correct the problem

• Press START button again and Close the Control Panel Cover

• Now the Landroid

®

M will begin to mow!

3.3 How big an area can my Landroid

®

M mow?

Your Landroid

®

M is capable of mowing areas of up to different size areas, although this depends on various factors, such as:

• Species of grass in your lawn and its growth rate

• Sharpness of the Cutting Blades (14)

• Humidity

• Surrounding temperature

• Amount of obstacles in your Lawn

If the surrounding temperature is very hot where you live then your Landroid

®

M may charge at a slightly slower rate. The

Landroid

®

M uses less energy in open areas that have fewer obstacles, such as flower beds, fountains, walkways, etc…

You can find the default work time of Landroid

®

M for different lawn size in programming guide .

Mowing times are different for every lawn depending on the factors mentioned previously. Gradually adjust the time you

allow your Landroid

®

M to mow each day until you find the most suitable setting.

You can also program Landroid

®

M working time to suit your schedule – refer to Programming Guide.

3.4 How efficiently will my Landroid

®

M mow the grass?

The Landroid

®

M’s cutting height can be adjusted between 2cm - 6cm. Before starting your Landroid

®

M for the first time,

you should cut the grass to the height not more than 9cm. Then make sure you open the Control Panel Cover (7) and set

the cutting height to its maximum cutting height of 6cm (See Fig. F,G).

Your Landroid

®

M will cut its best in dry weather. It does not like wet grass, which can build up on the Blade Turning Disc (13)

and within the motor, and can also cause loose traction and slippage while working.

Your Landroid

®

M is afraid of Lightening Storms. In case of a Lightening Storm, protect the Landroid

®

M by unplugging the

Charging Base (4), disconnecting the Boundary Wire (21), and making sure the Landroid

®

M is not allowed to charge.

Your Landroid

®

M loves mowing grass and requires the Cutting Blades (14) to be kept in good condition to cut at its best.

The Landroid

®

M can do most things by itself, but will need your help sometimes to prevent damage to itself.

• Never let the Landroid

®

M travel over gravel.

•

Remove or prevent access to obstacles that the

Landroid

®

M

could accidentally climb on and damage its Blade Turning Disc.

• Remove all debris and foreign objects from your lawn.

GF

Lawn Mowing Robot EN

11

4. Smart phone control

Your Lanroid

®

M(WG796E) could be connected to smart phone. All the general settings could be set on your phone. It will

also show the current working status, even errors. For the details settings, please refer to the Landroid Wifi Connection

Guide.

5. Boundary Wire Basics

5.1 Pegging the Boundary Wire

Use the Boundary Wire Distance Gauge (24) to set the correct

distance from the border of your lawn (More than 35cm *).

* This is the recommended distance. Use the provided distance

gauge to ensure proper installation.

If your neighbor also uses a Landroid

®

M, then you must keep a

spacing of at least 2 metres between your Boundary Wire and your

neighbors.

Please be aware that your Landroid

®

M will not be able to receive a

signal from the Boundary Wire beyond the distance of 18m.

The boundary wire must outline the intended mowing area

exactly.

Your Landroid

®

M will become confused by extra bends or coils of Boundary Wire that are not part of its mowing

area ( See Fig. H). If there is excess Boundary Wire after the mowing area has been outlined, then cut it off and store

this additional wire in a separate location. However, it is important to leave the necessary length where it connects to the

Charging Base so it can be connected and still remain buried.

5.2 Burying the Boundary Wire

If you are planning to bury the Boundary Wire then it should be noted that when entering its Charging Base for the first time,

your Landroid

®

M may find problems with the way you have laid the wire. It is recommended to first peg down the Boundary

Wire to the lawn so it is easy to make adjustments if necessary. This will allow the Landroid

®

M to become adjusted to its new

environment and ensures it will successfully work with the charging base before the Boundary Wire is buried.

When you have completed installing the boundary wire, it is recommended that you ask Landroid

®

M to follow the boundary

wire by pressing the home button.

Whilst observing Landroid

®

M locating the charging station you can then make alterations to the boundary wire route to

ensure trouble free tracking of the boundary wire by Landroid

®

M when locating the charging station.

5.3 Joining the Boundary Wire

The Boundary Wire (21) can be extended simply by splicing the ends

and connecting it to the ends of another piece of wire. You can use

insulating tape to secure the joined part of the wire. (See Fig. I)

5.4 Turn on and test installation

If the charger base LED does not come on, then check the power

connections.

If the charger base LED is flashing green, check if the boundary wire

is connected correctly.

Red light on: charging.

Red light flashing: error message, refer to Trouble Shooting and

correct the problems.

Green light flashing: check if the boundary wire is connected correctly.

When the green light on the charging base is on, place your Landroid

®

M over the boundary wire, if Landroid

®

M follows the

boundary it is connected correctly.

If your Landroid

®

M is inside its territory but the display says “Outside working area” ,and the charger

base LED is green, it means you clamped the boundary wire ends incorrectly. Just reverse them.

H

I

Lawn Mowing Robot EN

12

6. Software update

Your Landroid

®

M software can be updated when new versions

become available. The software version will be showed in the display.

The manual in box is based on the default software in the mass

production. Some new features/functions in the new version may not

exist in the manual. If you found some settings not in the manual,

please visit www.worxlandroid.com. to download the latest manual.

You can check the software version installed on your machine by

pressing the ON/OFF button.

The latest software can be downloaded from our website – see

below download and installation instructions;

Step 1: Locate the latest software version at : www.worxlandroid.com.

Copy the “.bin” file containing the latest software version to a USB

memory stick.

NOTE: Before transferring the “bin” file make sure the

memory stick does not contain other files or data.

Step 2: Open the cover at the bottom and remove the battery and

then insert the U disk to the USB port. (

See Fig.

J1)

Step 3: Insert the battery pack and press the ON/OFF button for ten

seconds until the mower is powered ON. The new software version will

be displayed in the bottom right corner of the display. (See Fig. J2)

Step 4: Remove the memory stick and refit the battery cover.

Step 5: After installing the new software you will need to reset the

diagnostic panel on your mower. Firstly, position the mower on a

horizontal surface.

Press Key “2” to enter the diagnosis interface, then press key “5”

for a few seconds until the three numbers 1 2 & 3 highlighted below

turn back to zero.(

See Fig.

J3)

7. Maintenance

Your Landroid

®

M needs to be checked from time to time. The

Landroid

®

M works hard and after time needs a good cleaning as well

as having some parts replaced, as they can become worn.

In the following we want to let you know how to take care of your

Landroid

®

M.

7.1 Keep it sharp

WARNING: Before cleaning, adjusting, or replacing

the Blades, turn your Landroid

®

M OFF by pressing

the ON/OFF Button to OFF and put on protective gloves.

WARNING: When fitting new blades, make sure

you replace ALL the blades. Always use new

screws when fitting blades. This is important to ensure

blade retention. Failure to use new screws could cause

serious injury.

The Landroid

®

M does not cut grass like other mowers. Its

Cutting Blades (14) are razor sharp on all 4 edges and spin in

both directions for maximum cutting capacity (See Fig. K ).Each

blade of your Landroid

®

M has 4 cutting edges. Depending on the

frequency the Landroid

®

M mows your lawn, the cutting blades will

need to be flipped/rotated periodically for a new cutting edge. If

your Landroid

®

M is programmed to mow the lawn every day then

the cutting blades will need to be rotated monthly for the best

mowing results. Each cutting blade will last up to 4 months when

it is programmed to mow every day. When the cutting blades are

dull and worn out, they should be replaced with the spare blades

1

2

3

J1

J2

J3

43

1 2

K

Lawn Mowing Robot EN

13

provided with your Landroid

®

M. Spare blades are also available at your nearest WORX retailer.

A. Rotate and flip the blades

Your Landroid

®

M carries the Blades that are all screwed onto the Blade Turning Disc (13). The Blades allow the

Landroid

®

M do its job and need care and attention. Every once in awhile, you should simultaneously rotate and flip all

blades for a perfect cut. When rotating and flipping the Blades, make sure all the Blades are adjusted at the same time

or else it could make the Blade Disc off balance. If your Landroid

®

M mows on a normal schedule (daily) then the Blades

should last one season if they are rotated and flipped every month. Always check to see if the Blades are chipped or

damaged and replace them if they are.

B. Replace the blades (See Fig. L)

After some time, usually every season, your Landroid

®

M’s Blades

will need to be replaced. Your Landroid

®

M does not like mowing

while using Blades of different age and quality. So when replacing

the Blades, make sure to replace all of them at the same time.

You can replace them with one of the three spare Blade kits and

extra Blade screws supplied with your Landroid

®

M.

Before attempting to replace your Landroid

®

M’s Blades, turn the

power off and put on protective gloves. Then follow these steps:

1. Gently flip the Landroid

®

M over.

2. Remove the battery cover and remove the battery.

3. Take the screws off the Blades with a screwdriver.

4. Firmly screw on the new Blades.

5. Refit the battery and the battery cover.

IMPORTANT: After screwing the Blade to the Blade

Disc, make sure the Blade is able to spin freely.

7.2 Keep it clean

WARNING: Before cleaning turn your Landroid

®

M

OFF by pressing the ON/OFF Button. Put on

protective gloves before cleaning the Blade Turning Disc

(13) and do not use running water. (See Fig. M)

A. Cleaning the body

Your Landroid

®

M will live a much happier and longer life if it is

cleaned regularly. Although, as your Landroid

®

M is an electric

machine, you will need to take care when cleaning, so DO NOT use

a hose, high pressure washers or otherwise pour running water on

your Landroid

®

M, it is best to use a spray bottle filled with water .

When cleaning the machine body use a soft brush or clean cloth and

avoid using solvents or polishes (See Fig. M). Lastly, make sure that

you remove all build up of grass clippings and debris.

B. Cleaning the Underside

Again, it is important that you power the Landroid

®

M OFF using the ON/Off Button and wear protective gloves

before touching the Blade Turning Disc (13).

First, flip your Landroid

®

M upside down to expose its underside. Here you will see the Blade Disc, the chassis, and the

Front Wheel (15) and Driving Wheel(10). Clean everything thoroughly with a soft brush or moist rag.

Rotate the Blade Disc to make sure it moves freely and that there is not anything lodged between it and the surrounding

Motor Frame Box. Also, make sure the Blades are able to spin freely and that there's no grass obstructing them.

IMPORTANT: Remove any lodged debris so that it does not cause a crack in the Blade Disc. Even the

tiniest crack can decrease your Landroid

®

M's mowing output.

C. Clean the contact pins and the charging strips

Clean the Contact Pins (3) located on the Charging Base (4) and the Charging Strip (5) located on the Landroid

®

M using a

cloth. Remove any build up of grass clippings and debris around the contact pins and charge strips periodically to ensure

the Landroid

®

M successfully charges each time.

M

L

Lawn Mowing Robot EN

14

7.3

Battery life

The heart of the Landroid

®

M is its 28-volt lithium-ion battery.

No maintenance is required. For proper storage of the battery,

make sure it is fully charged in kept in a cool dry place between

(20°C-60°C).

The life-span of the Landroid

®

M’s battery depends on various

factors, such as:

• The time span of the mowing season in your region.

• Amount of hours the Landroid

®

M mows per day.

• Battery maintenance during storage.

Landroid

®

M can be charged manually without the

boundary wire.(See Fig. N)

To manually charge the battery without connecting the

boundary wire to the charging base;

1. Connect the Charging Base to a suitable power supply.

2. Manually dock the Landroid

®

M into the Charging Base while the Landroid

®

M is powered off.

3. The charging base red light will turn on.

4. Within 3 seconds and before the charging base light turns green, press the Landroid

®

M power ON/

OFF button.

5. Landroid

®

M will begin to charge.

7.4 Winter hibernation

Your Landroid

®

M will live longer and healthier if it is allowed to hibernate. So even though it is tough, we would recommend

that you store your Landroid

®

M in your shed or garage during the winter.

Before you prepare your Landroid

®

M for winter hibernation, we recommend you:

• Thoroughly clean your Landroid

®

M

• Fully charge the battery

• Turn the power off

To maximize the battery life, it is recommended to fully charge the battery before storage during winter.

The Boundary Wire can be left in the ground although its ends should be protected, such as placed in a tin can with grease.

If the Charging Base is left outside for winter, leave the Boundary Wire connected.

NOTE: Before storing for winter, you can take your Landroid

®

M to a dealer for a thorough cleaning and tune-up, where its

functions will be tested and worn parts will be replaced.

When bringing the Landroid

®

M back to work after winter hibernation, make sure the Charging Strips (5) and Contact Pins (3)

are clean, it is recommended to use a fine grade emery cloth to clean. Then make sure the date and time are correct and

send the Landroid

®

M back to what it loves doing: mowing.

7.5 Replacing the battery

WARNING: Press the ON/OFF Key to OFF before attempting any adjustment, replacement or repair.

If you need to replace the Battery, follow these steps:

1. Gently turn your Landroid

®

M upside down.

2. Remove the four screws on the battery cover (See Fig. O).

3. Take out the old battery (See Fig. P).

4. Put in the new battery.

5. Firmly replace the 4 screws.

1

2

N

Lawn Mowing Robot EN

15

Environmental Protection

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.

Check with your Local Authority or retailer for recycling advice.

Plug Replacement (UK & Ireland Only)

If you need to replace the ﬁtted plug then follow the instructions below.

IMPORTANT

The wires in the mains lead are colored in

accordance with the following code:

Blue – Neutral

Brown – Live

As the colors of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows. The wire which is coloured blue must be connected to the terminal which is marked with N. The wire which

is coloured brown must be connected to the terminal which is marked with L.

WARNING: Never connect live or neutral wires to the earth terminal of the plug. Only ﬁt an approved BS1363/A plug and the

correct rated fuse.

NOTE: If a moulded plug is ﬁtted and has to be removed take great care in disposing of the plug and severed cable, it must be destroyed

to prevent engaging into a socket.

Connect

Blue to N

(neutral)

Outer sleeve

firmly clamped

Cable grip

Brown L (live)

13 Amp fuse approved

to BS1362

O

P

Roboter-Rasenmäher D

16

INHALT

1. Sicherheitsvorschriften

1.1 Allgemeine Sicherheitshinweise für Elektrowerkzeuge

1.2 Informationen zum Landroid

®

M

2. Komponenten

3. Wissenswertes zu Ihrem Landroid

®

M

3.1 Wie weiß mein Landroid

®

M, wo er mähen soll?

3.2 Wie weiß mein Landroid

®

M,wohin er fahren soll?

A. Ladebasis ﬁnden

B. Regensensor

C. Begrenzungskabel erkennen

D. Beim Mähen stoppen und wieder starten

3.3 Welche Fläche kann mein Landroid

®

M mähen?

3.4 Wie gut mäht der Landroid

®

M das Gras?

4. Smartphone-Steuerung

5. Grundlegendes zum Begrenzungskabel

5.1 Begrenzungskabel abstecken

5.2 Begrenzungskabel eingraben

5.3 Begrenzungskabel verbinden

5.4 Einschalten und Installation prüfen

6. Softwareaktualisierung

7. Wartung

7.1 Immer schön scharf

A. Messer drehen und umdrehen

B. Messer austauschen

7.2 Sauber halten

A. Gehäuse reinigen

B. Unterseite reinigen

C. Kontakte und Ladestreifen reinigen

7.3 Akkulaufzeit und -haltbarkeit

7.4 Überwintern

7.5 Akku austauschen

BEDIENUNGSANLEITUNG

17

19

20

22

23

24

25

26

27

28

29

Roboter-Rasenmäher D

17

1. Sicherheitsvorschriften

1.1 Allgemeine Sicherheitshinweise für Elektrowerkzeuge

WARNUNG: Lesen Sie alle Sicherheitshinweise und Anweisungen. Versäumnisse bei der

Einhaltung der Sicherheitshinweise und Anweisungen können elektrischen Schlag, Brand und/

oder schwere Verletzungen verursachen.

Lesen Sie die Bedienungsanleitung zum sicheren Betrieb des Gerätes aufmerksam durch.

Bewahren Sie alle Sicherheitshinweise und Anweisungen für die Zukunft auf.

•

Dieses Gerät ist nicht zur Verwendung durch Personen (einschließlich Kindern) vorgesehen, die über reduzierte körperliche

Eignung, Wahrnehmung oder geistige Fähigkeiten, Mangel an Erfahrung und Wissen verfügen, sofern diese Personen

nicht von einer verantwortlichen Person beaufsichtigt oder in der Verwendung des Gerätes unterwiesen wurden.

•

Kinder sollten grundsätzlich beaufsichtigt werden, damit sie nicht mit dem Gerät spielen.

•

Das Gerät darf nur mit dem mitgelieferten Netzteil verwendet werden.

VOR GEBRAUCH BITTE GENAU DURCHLESEN UND FÜR WEITERE FRAGEN AUFBEWAHREN

SICHERER BETRIEB

Training

a) Die Anweisungen aufmerksam durchlesen. Machen Sie sich mit den Bedienelementen und dem vorschriftsmäßigen

Gebrauch des Rasenmähers vertraut.

b) Niemals Kindern oder mit diesen Anweisungen nicht vertrauten Personen erlauben, den Rasenmäher zu benutzen.

Nationale Vorschriften können das Alter der Bedienperson möglicherweise beschränken.

c) Bedenken Sie, dass der Bediener oder Benutzer bei Unfällen oder Gefährdungen anderer Personen oder deren

Eigentum die Verantwortung trägt!

Vorbereitung

a) Stellen Sie sicher, dass das Begrenzungskabel gemäß den Anweisungen verlegt wird.

b) Inspizieren Sie die Gegend, in der die Ausrüstung eingesetzt werden soll, gründlich und entfernen Sie alle Objekte, die

durch die Maschine aufgeschleudert werden könnten.

c) Vor der Benutzung immer durch Augenschein prüfen, ob Messer, Messerschrauben und Schneidbalken abgenutzt oder

beschädigt sind. Abgenutzte Messer und Schrauben nur im ganzen Satz auswechseln, um Unwuchten zu vermeiden.

d) Achten Sie darauf, dass bei Geräten mit mehreren Klingen ein Klingensatz durch den anderen in Rotation versetzt werden kann.

e) WARNUNG! Der Rasenmäher darf nicht betrieben werden, wenn der Schutz nicht angebracht ist.

BETRIEB

1. ALLGEMEINE SICHERHEITSHINWEISE

a) Betreiben Sie das Gerät niemals mit defektem Schutz oder ohne installierte Sicherheitsvorrichtungen, wie etwa Deﬂektoren;

b) Hände und Füße nicht in die Nähe oder unter rotierende Teile bringen.

c) Niemals den Rasenmäher bei laufendem Motor anheben oder tragen.

d) Maschine ausschalten

- Vor dem Beseitigen einer Verstopfung;

- Vor dem Überprüfen, Reinigen oder Arbeiten am Gerät.

e) Der ursprüngliche Zustand des WORX

Landroid

®

M

darf nicht modiﬁziert werden. Alle Änderungen erfolgen auf eigene

Verantwortung.

f) Starten Sie den Roboter-Rasenmäher gemäß Anweisungen. Wenn der Netzschalter eingeschaltet ist, stellen Sie sicher, dass Sie

Ihre Hände und Füße von den drehenden Klingen entfernt halten. Bringen Sie Ihre Hände und Füße niemals unter den Rasenmäher.

g) Heben Sie den Roboter-Rasenmäher niemals an bzw. tragen Sie ihn nicht, wenn der Netzschalter eingeschaltet ist.

h) Erlauben Sie niemandem, der sich mit den Funktionen und Verhaltensmustern von WORX

Landroid

®

M

nicht auskennt, den

Mäher zu benutzen.

i) Keine Gegenstände auf den WORX

Landroid

®

M

oder seine Ladestation legen.

j) Wenn der Messerteller oder das Gehäuse defekt ist, darf der WORX

Landroid

®

M

nicht in Betrieb genommen werden. Das

gleiche gilt für defekte Messer, Schrauben, Muttern oder Kabel.

k) Schalten Sie den Roboter-Rasenmäher stets aus, wenn dieser nicht verwendet wird. Der Roboter-Rasenmäher kann nur

starten, wenn der Netzschalter eingeschaltet ist und der korrekte PIN-Code eingegeben wurde.

2. HINWEIS ZUM AUTOMATIKBETRIEB DES ROBOTERS

a) Den WORX

Landroid

®

M

niemals verwenden, wenn sich Personen – besonders Kinder – oder Haustiere in der Nähe aufhalten.

Roboter-Rasenmäher D

18

WARTUNG UND AUFBEWAHRUNG

WARNUNG! Wenn der Rasenmäher umgedreht wird, muss der Netzschalter stets ausgeschaltet

werden.

Der Netzschalter muss bei allen Arbeiten am Unterbau des Rasenmähers ausgeschaltet werden,

beispielsweise bei der Reinigung oder beim Wechseln der Klingen.

a) Den festen Sitz aller Schrauben, Muttern und Bolzen sicherstellen um zu gewährleisten, dass sich der Rasenmäher in

einem betriebssicheren Zustand beﬁndet;

b) Den WORX

Landroid

®

M

einmal pro Woche kontrollieren und eventuell beschädigte oder verschlissene Teile austauschen.

c) Messer und Messerteller besonders sorgfältig auf Schäden untersuchen. Bei Bedarf alle Messer und Schrauben

gleichzeitig austauschen, um eine Unwucht der rotierenden Teile zu vermeiden.

d) Verwenden Sie beim Austausch nur Original WORX Messer.

e) Verwenden Sie zum Laden des Akkus nur das vom Hersteller empfohlene Ladegerät. Eine nicht den Hinweisen

entsprechende Verwendung kann zu einem Stromschlag, zur Überhitzung oder zum Auslaufen der Batterieﬂüssigkeit führen.

f) Tritt Batterieﬂüssigkeit aus, beseitigen Sie sie mit Wasser und einem neutralen Reinigungsmittel. Kommt sie mit Augen

etc. in Kontakt, suchen Sie sofort einen Arzt auf.

g) Warten Sie den Roboter nach den Anweisungen des Herstellers.

Transport

Für längere Transporte legen Sie den WORX Landroid

®

M am besten in die Originalverpackung.

Für einen sicheren Transport vom oder innerhalb des Arbeitsbereichs:

a) Drücken Sie die STOP -Taste, um den Mäher zu stoppen.

b) Sie wählen den vierstelligen PIN aus, wenn Sie den Mäher das erste Mal benutzen.

c) Schalten Sie den Roboter-Rasenmäher immer aus, wenn Sie diesen tragen möchten.

d) Den Mäher an seinem Griff ganz hinten unten tragen. Halten Sie den Messerteller beim Tragen des Mähers vom Körper

weg.

Sicherheit hinweise für Akkupack

a) Zellen bzw. Akkupack nicht zerlegen, öffnen oder zerdrücken.

b) Akkupack nicht kurzschließen. Akkupacks nicht wahllos in einer Schachtel oder Schublade

aufbewahren, wo sie einander kurzschließen oder durch andere leitfähige Materialien

kurzgeschlossen werden könnten. Bei Nichtverwendung des Akkupacks ist dieses von Metallgegenständen

fernzuhalten, wie etwa Büroklammern, Münzen, Nägeln, Schrauben oder anderen kleinen Metallgegenständen, wo sich

die Batterieklemmen berühren könnten. Das Kurzschließen der Batterieklemmen kann Verbrennungen bzw. einen Brand

verursachen.

c) Zellen bzw. Akkupacks nicht Hitze oder Feuer aussetzen. Lagerung in direktem Sonnenlicht

vermeiden.

d) Akkupack nicht mechanischen Stößen aussetzen.

e) Im Fall, dass Flüssigkeit aus dem Akku austritt, darf diese nicht in Kontakt mit der Haut oder den

Augen kommen. Sollte dies dennoch geschehen, den betroffenen Bereich sofort mit viel Wasser

spülen und einen Arzt aufsuchen.

f) Beim Verschlucken einer Zelle oder eines Akkupacks muss sofort ein Arzt herangezogen werden.

g) Akkupack sauber und trocken halten.

h) Akkupacks funktionieren bei normaler Zimmertemperatur (20 °C ± 5 °C) am besten.

i) Beim Entsorgen von Akkupacks sollten Akkupacks mit verschiedenen elektrochemischen

Systemen voneinander getrennt gehalten werden.

j) Nur mit dem von WORX bezeichneten Ladegerät auﬂaden. Kein Ladegerät verwenden, das nicht

ausdrücklich für den Gebrauch mit dem Gerät vorgesehen ist. Ein Ladegerät, das für eine bestimmte Art

von Akkupackgeeignet ist, kann bei Verwendung mit einem anderen Akkupack eine Brandgefahr darstellen.

k) Kein Akkupack verwenden, das nicht für den Gebrauch mit dem Gerät vorgesehen ist.

l) Akkupacks von Kindern fernhalten.

m) Die originalen Produktunterlagen zum späteren Nachschlagen aufbewahren.

n) Ordnungsgemäß entsorgen.

Roboter-Rasenmäher D

19

1.2 Informationen zum Landroid

®

M

WARNUNG–Rasenmähroboter können bei inkorrekterVerwendung gefährlich sein.

Lesen Sie die Bedienungsanleitung sorgfältig durch und verstehen Sie deren Inhalt, bevor Sie

IhrenRasenmähroboter betreiben.

WARNUNG- Halten Sie einen Sicherheitsabstand zu Unbeteiligten ein.

WARNUNG –Betätigen Sie die Deaktivierungsvorrichtung, bevor Sie am Gerät arbeiten oder die Maschine

anheben.

WARNUNG–RASENMÄHROBOTER darf nicht als Transportmittel missbraucht werden.

Nicht im Feuer entsorgen

Nicht ins Wasser werfen

Akkus sollten dem Recycling zugeführt werden.

Akku nicht in den Haushaltsmüll geben. Bringen Sie den leeren Akku zu Ihrer lokalen Sammel- oder

Recyclingstelle.

Waschen Sie das Gerät nicht mit einem Hochdruckreiniger.

Schadhafte und/ oder entsorgte elektrische oder elektronische Geräte müssen an den dafür vorgesehenen

Recycling-Stellen abgegeben werden. Wir möchten Sie daher bitten, uns mit Ihrem aktiven Beitrag beim

Umweltschutz zu unterstützen und dieses Gerät bei den Wertstoff-/ Recycling-Sammelstellen abzugeben.

Bitte erkundigen Sie sich bei der örtlichen Behörde oder beim Vertragshändler über Müllsammlung und

-Entsorgung.

Roboter-Rasenmäher D

20

2. Komponenten

6

8

75

9

10

11

12

13

23

2221

17

19

16

18

3

4

2

1

25

20

24

15

14

La pagina sta caricando ...

Worx LANDROID WG796E Original Instructions Manual

Worx LANDROID WG796E Original Instructions Manual

in altre lingue

Documenti correlati

Altri documenti