Echo ES-255ES Manuale utente

Tipo
Manuale utente

Questo manuale è adatto anche per

1Top cover(co mposite volume)
OPERATOR'S MANUAL
MANUEL D'UTILISATION
BEDIENUNGSANLEITUNG
MANUALE D'ISTRUZIONI
MANUAL DE INSTRUCCIONES
ES-255ES
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
ESPAÑOL
WARNING
READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR
SAFE OPERATION.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.
AVERTISSEMENT
LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LES RE-GLES DE
SECURITE. LE NON-RESPECT DES REGLES DE SECU-RITE ENTRAINE UN
RISQUE DE BLESSURE GRAVE.
WARNUNG
LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND BE-
FOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS
RISIKO SCHWERER VERLETZUNGEN.
AVVERTENZA
LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LA-VORARE
IN CONDIZIONI DI MASSIMA SICUREZZA. LA MANCA-TA OSSERVANZA
DELLE ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.
ADVERTENCIA
LEA ATENTAMENTE LAS INSTRUCCIONES Y SIGA LAS INDICA-CIONES
PARA UN FUNCIONAMIENTO SEGURO. DE NO HACER-LO, PODRÍA SUFRIR
LESIONES GRAVES.
1Top cover
ENGLISH
OPERATOR'S MANUAL
ES-255ES
WARNING
READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE
RULES FOR SAFE OPERATION.
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.
2
Important information
2Important information
Please ensure that you read the operator's manual before using your product.
Intended use of this product
ECHO Power Blower are designed for vacuuming and processing a wide variety of fallen leaves and cut lawn. Also this
unit is easily converted to a blower.
Do not use this unit for any purpose other than aforementioned.
Users of the product
You should not use this product until you have read the operator's manual carefully and fully absorbed its content.
This product should not be used by anyone who has failed to read the operator's manual properly, is suffering from a
cold, tiredness or otherwise in poor physical condition, or children.
Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-
erty.
About your operator's manual
This manual contains necessary information about the assembly, operation, and maintenance of your product. Please
read it carefully and absorb its contents.
Always keep your manual in a place where it is readily accessible.
If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your ECHO
DEALER.
The units used in this manual are SI units (International System of Units). Figures in parentheses are reference values,
and there may be a slight conversion error in some cases.
Loaning or assigning your product
When loaning the product described in this manual to another party, ensure that the person borrowing and working with
the product receives the operator's manual along with the product. If you assign your product to another party, please
enclose the operator's manual with the product when handing it over.
Enquiries
Please contact your ECHO DEALER for requests regarding information about your product, the purchase of consum-
ables, repairs, and other such enquiries.
Notices
The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the
illustrations used may differ from the product itself in order to make the explanations clearer.
This product requires the assembly of some parts.
Please consult your ECHO DEALER if anything is unclear or of concern.
Feature of this model: "ES" START
"ES" START generates enough revolving power to rotate crankshaft up to a speed to ignite the engine and bring almost no kick-
back.
"ES" START makes engine start far easier than you ever expect.
3
Contents
For safe use of your product...............................................................................................4
Warning notices.............................................................................................................4
Other indicators .............................................................................................................4
Symbols.........................................................................................................................4
Location in which the safety decal is attached...............................................................6
Handling fuel..................................................................................................................7
Handling the engine.......................................................................................................8
Handling the product .....................................................................................................9
Packing list........................................................................................................................12
Description........................................................................................................................13
Before you start ................................................................................................................14
Assembly.....................................................................................................................14
Preparing the fuel ........................................................................................................17
Engine operation...............................................................................................................18
Starting the engine ......................................................................................................18
Stopping the engine.....................................................................................................19
Operation..........................................................................................................................20
Operating vacuum .......................................................................................................20
Operating blower .........................................................................................................21
Maintenance and care ......................................................................................................22
Servicing guidelines.....................................................................................................22
Maintenance and care.................................................................................................22
Troubleshooting table..................................................................................................27
Long-term storage(30 days or more)...........................................................................28
Specifications....................................................................................................................29
Declaration "CE" of conformity .........................................................................................30
4
For safe use of your product
For safe use of your product
Be careful to read this section before using your product.
The precautions described in this section contain important safety information. Please observe them carefully.
You must also read the precautions that appear in the body of the manual itself.
Text following a [diamond mark] mark describes the potential consequences of failing to observe the precaution.
Warning notices
Situations where there is a risk of physical injury to the operator and other people are indicated in this manual and on the product
itself by the following warning notices. Always read and observe them carefully in order to ensure safe operation.
Other indicators
As well as warning notices, this manual uses the following explanatory symbols:
Symbols
In this manual and on the product itself, a series of explanatory symbols is used. Please make sure that you fully understand what
each symbol means.
DANGER WARNING CAUTION
This symbol accompanied by the
word "DANGER" calls attentions to
an act or a condition which will lead to
serious personal injury or death of op-
erators and bystandars.
This symbol accompanied by the
word "WARNING" calls attentions to
an act or a condition which can lead to
serious personal injury or death of op-
erators and bystanders.
"CAUTION" indicates a potentially
hazardous situation which, if not
avoided, may result in minor or mod-
erate injury.
Circle and slash sym-
bol means whatever is
shown is prohibited.
NOTE IMPORTANT
This enclosed message provides tips
for use, care and maintenance of the
product.
Framed text featuring the word "IM-
PORTANT" contains important infor-
mation about the use, checking,
maintenance and storage of the prod-
uct described in this manual.
Symbol form/shape Symbol description/applica-
tion Symbol form/shape Symbol description/applica-
tion
Carefully read the operator's
manual Petrol and oil mixture
Wear eyes, ears and head
protection Purge bulb (Primer)
Safety / Alert Carburettor adjustment
- Low speed mixture
Emergency stop Carburettor adjustment
- High speed mixture
Finger Severing Carburettor adjustment
- Idle speed
5
For safe use of your product
Do not use the product in plac-
es with poor ventilation
Choke Control
"Cold Start"
Position
(Choke Closed)
Beware of fire
Choke Control
"Run"
Position
(Choke Open)
Beware of electric shocks Idle speed
Guaranteed sound power lev-
el Fast speed
Ignition
ON / OFF Beware of high-temperature
areas
Symbol form/shape Symbol description/applica-
tion Symbol form/shape Symbol description/applica-
tion
6
For safe use of your product
Location in which the safety decal is attached
The safety decal shown below has been attached to the product described in this manual. Ensure that you understand what the
decal means before using your product.
If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal
from your ECHO DEALER and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all
times.
1. Safety decal (Part number X505002310)
2. Safety decal (Part number X505002080)
3. Safety decal (Part number X503008950)
7
For safe use of your product
Handling fuel
DANGER
Always keep well away from fire when refuelling
Fuel is highly inflammable and leads to a risk of fire if mishandled. Use extreme care when mixing, storing or handling
or serious personal injury may result. Be careful to observe the following instructions.
Do not smoke or hold a flame near when refuelling.
Do not fuel up while the engine is hot or in operation.
If you do so, the fuel could ignite and cause fire, leading to burns.
About the container and refuelling place
Use an approved fuel container.
Fuel tanks/cans may be under pressure.
Always loosen fuel caps slowly allowing pressure to
equalize.
DO NOT fill fuel tanks indoors.
ALWAYS fill fuel tanks outdoors over bare ground.
Fuel spills can cause fire
Observe the following precautions when refuelling:
Do not add so much fuel that it reaches the mouth of the
fuel tank. Keep the fuel within the prescribed level (up to
the shoulder level of the fuel tank).
Mop up any fuel that overflows or spills out due to over-
filling.
Tighten the fuel tank cap securely after refuelling.
Fuel spills can cause fire and burns when ignited.
1. Fuel tank
2. Shoulder level
Do not start the engine in the area where you refu-
eled
You must not start the engine in the place where you
carried out the refuelling. Move at least 3m from the
place where you refueled before starting the engine.
Fuel leaks that occur while refuel-
ling can cause fire if ignited.
Fuel leaks cause fire
After refuelling, always check
that there are no leaks or dis-
charges of fuel from the fuel
pipe, fuel system grommets, or
around the fuel tank cap.
If you do find fuel leaks or discharges, stop using the
product immediately and contact your ECHO DEALER
to have it repaired.
Any fuel leaks could cause fire.
8
For safe use of your product
Handling the engine
WARNING
Starting the engine
Be particularly careful to observe the following precau-
tions when starting the engine:
Check that none of the nuts and bolts are loose
Check that there are no fuel leaks
Place the product in a flat, well ventilated place
Leave plenty of space around the product and do not al-
low people or animals near it
Remove obstructions, if any
Start the engine with the throttle lever in the start/oper-
ation position
Hold the product firmly to the ground when starting the
engine
Failure to observe the precautions could cause an accident
or injury, or even lead to a fatality.
Once the engine has started, check for abnormal vi-
brations and sounds
Check that there are no abnormal vibrations or sounds
once the engine starts. Do not use the product if there
are abnormal vibrations or sounds. Contact your ECHO
DEALER to have it repaired.
Accidents involving parts that fall or shatter off can cause
wounds or serious injury.
Do not touch high temperature or high voltage com-
ponents while the product is running
Do not touch the following high temperature or high volt-
age components while the product is running or for some
time after it stops.
Muffler, cylinder, and other high tempera-
ture components
You could burn yourself if you touch a high
temperature component.
Spark plug, spark plug wire, and other
high voltage components
You could receive an electric shock if you
touch a high voltage component while the
product is running.
Put safety first in the case of fire or smoke
If fire comes from the engine or smoke appears from
any area other than the exhaust vent, first distance
yourself from the product to ensure your physical safe-
ty.
Use a shovel to throw sand or other such
material on the fire to prevent it from
spreading, or put it out with a fire extin-
guisher.
A panicked reaction could result in the fire and
other damage becoming more extensive.
Exhaust fumes are toxic
The exhaust fumes from the engine contain toxic gases.
Do not operate the product indoors or in a plastic green-
house or in other ill ventilated places.
The exhaust fumes could cause poisoning.
Turn off the engine when checking or maintaining
the product
Observe the following precautions when checking and
maintaining your product after use:
Turn the engine off and do not attempt to check or main-
tain the product until the engine has cooled
You could burn yourself.
Remove the spark plug cap before performing checks
and maintenance
An accident could occur if the product starts unexpectedly.
Checking the spark plug
Observe the following precautions when checking the
spark plug.
If the electrodes or terminals are worn, or if there are
cracks in the ceramics, replace them with new parts.
The spark test (for checking whether the spark plug is
sparking) must be carried out by a professional. Please
ask your ECHO DEALER.
The spark test must not be carried out in proximity of
the spark plug hole.
The spark test must not be performed in places where
there are fuel spills or inflammable gases
You must not touch the
metal parts of the spark
plug
The spark plug could ig-
nite a fire or give you an
electric shock.
9
For safe use of your product
Handling the product
General precautions
WARNING
Operator's manual
Be careful to read the operator's manual
properly before using your product in or-
der to ensure correct operation.
Failure to do so could lead to an accident or
serious injury.
Do not use the product for anything
other than its intended purpose
You must not use the product for any purpose other
than those described in the operator's manual.
To do so could lead to an accident or serious injury.
Do not modify the product
You must not modify the product.
To do so could lead to an accident or serious injury. Any
malfunction resulting from a modification to the product will
not be covered by the manufacturer's warranty.
Do not use the product unless it has been checked
and maintained
You must not use the product unless it has been
checked and maintained. Always ensure that the prod-
uct is checked and maintained on a regular basis.
Failure to do so could lead to an accident or serious injury.
Loaning or assigning your product
When loaning your product to another party, ensure
that the person borrowing the product receives the op-
erator's manual along with it.
If you assign your product to another party, please en-
close the operator's manual with the product when
handing it over.
Failure to do so could lead to an accident or serious injury.
Being prepared in case of an injury
In the unlikely event of an accident or injury, please ensure
that you are prepared.
First aid kit
Towels and wipes (to stop any bleeding)
Whistle or mobile phone (for calling outside help)
If you are unable to perform first aid or call for outside help,
the injury could worsen.
10
For safe use of your product
Precautions for use
WARNING
Users of the product
The product should not be used by:
people who are tired
people who have taken alcohol
people who are on medication
people who are pregnant
people who are in poor physical
condition
people who have not read the op-
erator's manual
children
Failure to observe these instruc-
tions could lead to an accident.
Environment of use and operation
Do not use the product in places where there is no sure
foothold, such as on steep slopes or after rainfall, as
such places are slippery and dangerous.
Do not operate the product at night or in dark places
with poor visibility.
A serious injury could result if you fall or slip, or fail to oper-
ate the product correctly.
Using the product
When using the product, pay special attention to observe
the following precautions.
Do not allow people who are irrelevant to the work con-
ducted or animals to be in the worksite.
Do not point the blower pipe at people or animals.
Do not use the product in places where there is no sure
foothold.
Hold the arm tightly.
Avoid using the product late at night or early in the
morning so that the neighbors will not be disturbed by
noise.
Failure to observe these instructions could lead to an acci-
dent or injury.
Turn off the engine when moving around
When moving around in the situations described below,
turn off the engine and move with the product shouldered.
Moving to the place where you are working
Moving to another area while you are working
Leaving the place where you have been working
Failure to observe these precautions could cause burns or
serious injury.
When transporting the product by car, empty the fuel
tank, put the product in the upright position, and secure
it firmly in place to prevent it from moving around.
Travelling by car with fuel in the fuel tank could lead to a fire.
Be careful not to get caught in the fan
Be careful not to get your hair caught in the fan.
Never put your hand in between the engine and the
backpack frame when the product is in operation.
The wind pressure from the fan could make your hand get
caught in the fan, resulting in a serious injury.
Vibration and cold
It is believed that a condition called Raynaud's Phenome-
non which affects the fingers of certain individuals may be
brought about by exposure to vibration and cold. Expo-
sure to vibration and cold may cause tingling and burning,
followed by loss of colour and numbness in the fingers.
The following precautions are strongly recommended be-
cause the minimum exposure which might trigger the ail-
ment is unknown.
Keep your body warm, especially the head and neck,
feet and ankles, and hands and wrists.
Maintain good blood circulation by performing vigorous
arm exercises during frequent work breaks, and also by
not smoking.
Limit the number of hours of operation.
Try to fill each day with jobs where operating the blower
or other hand-held power equipment is not required.
If you experience discomfort redness and swelling of
the fingers, followed by whitening and loss of feeling,
consult your physician before exposing yourself further
to cold and vibration.
Failure to observe these instructions could result in damage
to your health.
11
For safe use of your product
Protective gear
WARNING
Repetitive stress injuries
It is believed that over-using the muscles and tendons of
the fingers, hands, arms and shoulders may cause sore-
ness, swelling, numbness, weakness and extreme pain to
the areas just mentioned. Certain repetitive hand activities
may put you at a high risk for developing a repetitive
stress injury (RSI).
To reduce the risk of RSI, do the following:
Avoid using your wrist in a bent, extended or twisted
position.
Take periodic breaks to minimize repetition and rest
your hands. Reduce the speed and force in which you
do the repetitive movement.
Do exercises to strengthen hand and arm muscles.
See a doctor if you feel tingling, numbness or pain in
your fingers, hands, wrists or arms. The sooner RSI is
diagnosed, the more likely permanent nerve and muscle
damage can be prevented.
Failure to observe these instructions could result in damage
to your health.
Turn off the engine immediately if anything goes
wrong
Turn off the engine immediately if the product suddenly
starts to emit abnormal sounds or vibrate abnormally.
The product cannot be used when it suffers from abnor-
mal vibration or sounds.
Contact your ECHO DEALER for repair.
Continuing to use parts when they are damaged could lead
to an accident or serious injury.
WARNING
Wear protective gear
Wear appropriate work clothes and protective gear
when working with the power blower. Above all, make
sure to wear safety goggles, a dust mask, and ear muffs
at all times while working.
Without the protective gear, you could inhale the debris or
dust blown away or get them in your eyes, which could lead
to an accident or injury.
a Head protection (helmet): Protects the head
b Ear muffs or ear plugs: Protect the hearing
c Safety goggles: Protect the eyes
d Dust mask
e Safety gloves: Protect the hands from cold and vibration
f Work clothes that fit (long sleeves, long trousers): Pro-
tect the body
g Heavy duty, non-slip protective boots (with toecaps) or
non-slip work shoes (with toecaps): Protect the feet
Failure to observe these precautions could result in damage
to your sight or hearing, or lead to a serious injury.
Wear proper clothing.
Do not wear ties, jewellery, or loose, dangling clothing which could be
caught in the unit. Do not wear open toed footwear, or go bare-foot or
barelegged. In certain situations, total face and head protection may be re-
quired.
Failure to observe these precautions could result in damage to your sight or
hearing, or lead to a serious injury.
12
Packing list
Packing list
The following parts are packed separately in the packing box.
When you have unpacked the box, please check the parts that it contains.
Contact your ECHO DEALER if anything is missing or broken.
Number Part name Quantity Number Part name Quantity
(1) Power Head 1 (5) Blower Pipe(Main Pipe) 1
(2) Vacuum Tube 1 (6) Blower Pipe(Fan Head Nozzle) 1
(3) Vacuum Elbow 1 (7) Operator's Manual 1
(4) Debris Bag 1 (8) T-Wrench 1
13
Description
Description
1. Stop switch "SLIDE SWITCH" mounted on top of handle.
Push forward to start and run. Slide back to stop.
2. Spark plug Provides spark to ignite fuel mixture.
3. Air cleaner Contains replaceable air filter element.
4. Fuel tank Contains fuel and fuel filter.
5. Fuel tank cap Covers and seals fuel tank.
6. Starter handle The grip of the starter, for starting the en-
gine.("ES"START)
7. Spark arrestor - Catalytic muffler / Muffler The muffler
or catalytic muffler controls exhaust noise and emission.
The spark arrestor screen prevents hot, glowing parti-
cles of carbon from leaving the muffler. Keep exhaust
area clear of flammable debris.
8. Choke Choke is located on top of the air cleaner. Move
choke lever to position to close choke for cold start-
ing. Move choke lever to position to open choke.
9. Purge bulb Pumping purge bulb before starting engine
draws fresh fuel from the fuel tank, purging air from the
carburetor. Pump purge bulb until fuel is visible and
flows freely in the clear fuel tank return line. Pump
purge bulb an additional 4 or 5 times.
10. Blower pipes Exclusive positive locking system.
11. Throttle position lever Pull back to increase engine
speed. Friction washers maintain throttle lever setting.
12. Throttle trigger Spring loaded to return to idle when re-
leased. During acceleration, press trigger gradually for
best operating technique.
13. Serial number label Lists model number and serial
number of unit.
14. Locking ring Locks blower pipe.
15. Vacuum tube Sucks in materials to be shredded.
16. Vacuum elbow Discharges shredded material.
17. Debris bag Collects shredded material.
14
Before you start
Before yo u start
Assembly
Install vacuum tube 1. Turn knob counter clockwise until hinged housing cover is
free to open for vacuum tube installation.
2. Opening housing cover, slide recess (G) on vacuum tube
into locking rib (H) , and turn the vacuum tube clockwise so
that it would be locked.
Install debris bag
1. Stand unit upright on blower base.
2. Release locking ring with a coin or screwdriver, and rotate so
that lock symbol (A) is at top of ring.
WARNING
Read the operator's manual carefully to ensure that you assemble the product correctly.
Never perform maintenance or assembly procedures with engine running.
Using a product that has been incorrectly assembled could lead to an accident or serious injury.
1. Knob
1. Vacuum tube 2. Housing cover
NOTE
Engine will not start/operate unless safety interlock switch (I) is
activated by the vacuum tube.
1. Locking ring
15
Before you start
3. Align locking ribs (J) on vacuum elbow with recesses (B) in
locking ring, and slide vacuum elbow into locking ring.
4. After pushing vacuum elbow all the way in fan case so that
line (K) will meet locking ring, rotate locking ring clockwise
1/8 turn to lock vacuum elbow in place.
5. Place debris bag opening over flared end of vacuum elbow,
and cinch debris bag securely at the position (L) with Velcro
strap.
Install blower pipes for blower usage
1. Stand unit upright on blower base.
2. Release locking ring with a coin or screwdriver, and rotate so
that lock symbol (A) is at top of ring.
1. Vacuum elbow
1. Locking ring
1. Debris bag
16
Before you start
3. Align locking ribs (C) on the blower pipe(main pipe) with re-
cesses (B) in locking ring, and slide the blower pipe(main
pipe) into locking ring.
4. After pushing upper blower all the way in fan case so that
line (D) will meet locking ring, rotate locking ring clockwise
1/8 turn to lock the blower pipe(main pipe) in place.
5. Align tabs (F) with grooves (E) and slide the blower pipe(fan
head nozzle) over the blower pipe(main pipe) until there is
light resistance.
6. Assemble the blower pipe(fan head nozzle) onto the blower
pipe(main pipe) until you feel light resistance. Do not force
connection. Hold the blower pipe(main pipe), and turn the
blower pipe(fan head nozzle) clockwise, engaging positive
locking channels until connection is firm. Do not force con-
nection.
Remove blower pipes 1. Release locking ring with a coin or screwdriver, and rotate
ring so that lock symbol (A) is at top of ring.
2. Remove pipes from locking ring.
1. Locking ring
1. Blower pipe(main pipe)
1. Blower pipe(main pipe)
NOTE
Blower use will eventually loosen pipe connections. Exclusive
positive locking system allows pipes to be tightened. If loosen-
ing occurs, remove the blower pipe(fan head nozzle) and in-
stall according to instructions 5 & 6.
1. Blower pipe(main pipe) 2. Blower pipe(fan head
nozzle)
1. Blower pipe(main pipe)
1. Blower pipe(main pipe) 2. Locking ring
17
Before you start
Preparing the fuel
Fuel Fuel is a mixture of regular grade petrol and an air-cooled 2-
stroke engine oil of reputable brand name.
Minimum 89 Octane unleaded petrol is recommended. Do not
use fuel containing methyl alcohol or more than 10 % of ethyl
alcohol.
Recommended mixture ratio; 50 : 1 (2 %) for ISO-L-EGD
Standard (ISO/CD 13738), JASO FC,FD grade and ECHO
Premium 50 : 1 oil.
- Do not mix directly in engine fuel tank.
- Avoid spilling petrol or oil. Spilling fuel should always be
wiped up.
- Handle petrol with care, it is highly inflammable.
- Always store fuel in approved container.
Fuel supply Always refuel in a well ventilated location. Do not pour fuel in-
doors.
Place the product and the refuelling tank on the ground when
performing the refuelling operation. Do not refuel the product
on the loading platform of a truck, or in other such places.
Always ensure that the fuel level remains below the shoulder
level of the fuel tank when refuelling.
There is a difference in pressure between the fuel tank and the
outside air. When refuelling, loosen the fuel tank cap slightly to
eliminate the difference in pressure.
Always wipe up any fuel spills.
Move at least 3m away from where you refueled before you
start the engine.
Keep the refuelling tank in a shaded area away from fire.
DANGER
Fuel is highly inflammable and there is a risk of fire if it is handled incorrectly. Carefully read
and observe the precautions in the section of this manual titled "For safe use of your prod-
uct".
Once the refuelling is complete, securely tighten the fuel tank cap and do not forget to
check that there are no leaks or discharges of fuel from the fuel pipe, fuel system grommets,
or around the fuel tank cap. If you do find fuel leaks or discharges, stop using the product
immediately and contact your ECHO DEALER to have it repaired.
If the fuel ignites, it could cause burns and fire.
CAUTION
There is difference in pressure between the fuel tank and the outside air. When refuelling, loosen the fuel tank cap
slightly to eliminate the difference in pressure.
Otherwise, fuel may get spewed.
NOTE
Stored fuel ages. Do not mix more fuel than you expect use in thirty (30) days. Do not mix directly in fuel tank.
1. Fuel tank 2. Shoulder level
18
Engine operation
Engine operation
Starting the engine
Starting a cold engine Recoil starter: Use short pulls - only 1/2-2/3 of rope length for
starting. Do not allow the rope to snap back in. Always hold
the unit firmly.
1. Stop Switch
Move stop switch away from the STOP position.
2. Throttle Position Lever
Move throttle position lever midway between idle and full
throttle positions.
3. Choke
Move choke to " " position.
4. Purge Bulb
Pump purge bulb until fuel is visible and flows freely in the
clear fuel tank return line.
5. Recoil Starter
Place the unit on a flat, clear area. Firmly grasp throttle grip
with left hand and rapidly pull recoil starter handle/rope until
engine fires , or maximum 5 pulls.
6. Choke
Move choke to " " position and if necessary, restart engine.
After engine warm up, gradually depress throttle trigger to in-
crease engine RPM to operating speed.
WARNING
When starting the engine, observe the precautions described from Page 4 in the section "For safe use of your prod-
uct" to ensure that you operate the product correctly.
Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.
NOTE
Pull out the starter grip gently at first, and then more rapidly. Do not pull the starter rope out to more than 2/3 of its length.
Do not let go of the starter grip as it returns.
To start the engine, return the choke knob when you hear the first explosion-like sound and pull on the starter grip again. Be
careful not to miss the first explosion-like sound.
1. Stop switch 2. Throttle position lever
1. Choke 2. Purge bulb
1. Recoil starter
1. Choke
NOTE
If engine does not start after 5 pulls, repeat instructions 3-6.
NOTE
Allow engine to warm up before use.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180

Echo ES-255ES Manuale utente

Tipo
Manuale utente
Questo manuale è adatto anche per

Documenti correlati