Echo PB-255ES Manuale utente

1Top cover(co mposite volume)

OPERATOR'S MANUAL

MANUEL D'UTILISATION

BEDIENUNGSANLEITUNG

MANUALE D'ISTRUZIONI

MANUAL DE INSTRUCCIONES

ES-255ES

ENGLISH

FRANÇAIS

DEUTSCH

ITALIANO

ESPAÑOL

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR

SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

AVERTISSEMENT

LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LES RE-GLES DE

SECURITE. LE NON-RESPECT DES REGLES DE SECU-RITE ENTRAINE UN

RISQUE DE BLESSURE GRAVE.

WARNUNG

LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND BE-

FOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS

RISIKO SCHWERER VERLETZUNGEN.

AVVERTENZA

LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LA-VORARE

IN CONDIZIONI DI MASSIMA SICUREZZA. LA MANCA-TA OSSERVANZA

DELLE ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.

ADVERTENCIA

LEA ATENTAMENTE LAS INSTRUCCIONES Y SIGA LAS INDICA-CIONES

PARA UN FUNCIONAMIENTO SEGURO. DE NO HACER-LO, PODRÍA SUFRIR

LESIONES GRAVES.

1Top cover

ENGLISH

OPERATOR'S MANUAL

ES-255ES

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE

RULES FOR SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

2

Important information

2Important information

Please ensure that you read the operator's manual before using your product.

Intended use of this product

ECHO Power Blower are designed for vacuuming and processing a wide variety of fallen leaves and cut lawn. Also this

unit is easily converted to a blower.

Do not use this unit for any purpose other than aforementioned.

Users of the product

You should not use this product until you have read the operator's manual carefully and fully absorbed its content.

This product should not be used by anyone who has failed to read the operator's manual properly, is suffering from a

cold, tiredness or otherwise in poor physical condition, or children.

Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-

erty.

About your operator's manual

This manual contains necessary information about the assembly, operation, and maintenance of your product. Please

read it carefully and absorb its contents.

Always keep your manual in a place where it is readily accessible.

If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your ECHO

DEALER.

The units used in this manual are SI units (International System of Units). Figures in parentheses are reference values,

and there may be a slight conversion error in some cases.

Loaning or assigning your product

When loaning the product described in this manual to another party, ensure that the person borrowing and working with

the product receives the operator's manual along with the product. If you assign your product to another party, please

enclose the operator's manual with the product when handing it over.

Enquiries

Please contact your ECHO DEALER for requests regarding information about your product, the purchase of consum-

ables, repairs, and other such enquiries.

Notices

The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the

illustrations used may differ from the product itself in order to make the explanations clearer.

This product requires the assembly of some parts.

Please consult your ECHO DEALER if anything is unclear or of concern.

Feature of this model: "ES" START

"ES" START generates enough revolving power to rotate crankshaft up to a speed to ignite the engine and bring almost no kick-

back.

"ES" START makes engine start far easier than you ever expect.

3

Contents

For safe use of your product...............................................................................................4

Warning notices.............................................................................................................4

Other indicators .............................................................................................................4

Symbols.........................................................................................................................4

Location in which the safety decal is attached...............................................................6

Handling fuel..................................................................................................................7

Handling the engine.......................................................................................................8

Handling the product .....................................................................................................9

Packing list........................................................................................................................12

Description........................................................................................................................13

Before you start ................................................................................................................14

Assembly.....................................................................................................................14

Preparing the fuel ........................................................................................................17

Engine operation...............................................................................................................18

Starting the engine ......................................................................................................18

Stopping the engine.....................................................................................................19

Operation..........................................................................................................................20

Operating vacuum .......................................................................................................20

Operating blower .........................................................................................................21

Maintenance and care ......................................................................................................22

Servicing guidelines.....................................................................................................22

Maintenance and care.................................................................................................22

Troubleshooting table..................................................................................................27

Long-term storage(30 days or more)...........................................................................28

Specifications....................................................................................................................29

Declaration "CE" of conformity .........................................................................................30

4

For safe use of your product

Be careful to read this section before using your product.

The precautions described in this section contain important safety information. Please observe them carefully.

You must also read the precautions that appear in the body of the manual itself.

Text following a [diamond mark] mark describes the potential consequences of failing to observe the precaution.

Warning notices

Situations where there is a risk of physical injury to the operator and other people are indicated in this manual and on the product

itself by the following warning notices. Always read and observe them carefully in order to ensure safe operation.

Other indicators

As well as warning notices, this manual uses the following explanatory symbols:

Symbols

In this manual and on the product itself, a series of explanatory symbols is used. Please make sure that you fully understand what

each symbol means.

DANGER WARNING CAUTION

This symbol accompanied by the

word "DANGER" calls attentions to

an act or a condition which will lead to

serious personal injury or death of op-

erators and bystandars.

This symbol accompanied by the

word "WARNING" calls attentions to

an act or a condition which can lead to

serious personal injury or death of op-

erators and bystanders.

"CAUTION" indicates a potentially

hazardous situation which, if not

avoided, may result in minor or mod-

erate injury.

Circle and slash sym-

bol means whatever is

shown is prohibited.

NOTE IMPORTANT

This enclosed message provides tips

for use, care and maintenance of the

product.

Framed text featuring the word "IM-

PORTANT" contains important infor-

mation about the use, checking,

maintenance and storage of the prod-

uct described in this manual.

Symbol form/shape Symbol description/applica-

tion Symbol form/shape Symbol description/applica-

tion

Carefully read the operator's

manual Petrol and oil mixture

Wear eyes, ears and head

protection Purge bulb (Primer)

Safety / Alert Carburettor adjustment

- Low speed mixture

Emergency stop Carburettor adjustment

- High speed mixture

Finger Severing Carburettor adjustment

- Idle speed

5

For safe use of your product

Do not use the product in plac-

es with poor ventilation

Choke Control

"Cold Start"

Position

(Choke Closed)

Beware of fire

Choke Control

"Run"

Position

(Choke Open)

Beware of electric shocks Idle speed

Guaranteed sound power lev-

el Fast speed

Ignition

ON / OFF Beware of high-temperature

areas

Symbol form/shape Symbol description/applica-

tion Symbol form/shape Symbol description/applica-

tion

6

For safe use of your product

Location in which the safety decal is attached

The safety decal shown below has been attached to the product described in this manual. Ensure that you understand what the

decal means before using your product.

If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal

from your ECHO DEALER and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all

times.

1. Safety decal (Part number X505002310)

2. Safety decal (Part number X505002080)

3. Safety decal (Part number X503008950)

7

For safe use of your product

Handling fuel

DANGER

Always keep well away from fire when refuelling

Fuel is highly inflammable and leads to a risk of fire if mishandled. Use extreme care when mixing, storing or handling

or serious personal injury may result. Be careful to observe the following instructions.

Do not smoke or hold a flame near when refuelling.

Do not fuel up while the engine is hot or in operation.

If you do so, the fuel could ignite and cause fire, leading to burns.

About the container and refuelling place

Use an approved fuel container.

Fuel tanks/cans may be under pressure.

Always loosen fuel caps slowly allowing pressure to

equalize.

DO NOT fill fuel tanks indoors.

ALWAYS fill fuel tanks outdoors over bare ground.

Fuel spills can cause fire

Observe the following precautions when refuelling:

Do not add so much fuel that it reaches the mouth of the

fuel tank. Keep the fuel within the prescribed level (up to

the shoulder level of the fuel tank).

Mop up any fuel that overflows or spills out due to over-

filling.

Tighten the fuel tank cap securely after refuelling.

Fuel spills can cause fire and burns when ignited.

1. Fuel tank

2. Shoulder level

Do not start the engine in the area where you refu-

eled

You must not start the engine in the place where you

carried out the refuelling. Move at least 3m from the

place where you refueled before starting the engine.

Fuel leaks that occur while refuel-

ling can cause fire if ignited.

Fuel leaks cause fire

After refuelling, always check

that there are no leaks or dis-

charges of fuel from the fuel

pipe, fuel system grommets, or

around the fuel tank cap.

If you do find fuel leaks or discharges, stop using the

product immediately and contact your ECHO DEALER

to have it repaired.

Any fuel leaks could cause fire.

8

For safe use of your product

Handling the engine

WARNING

Starting the engine

Be particularly careful to observe the following precau-

tions when starting the engine:

Check that none of the nuts and bolts are loose

Check that there are no fuel leaks

Place the product in a flat, well ventilated place

Leave plenty of space around the product and do not al-

low people or animals near it

Remove obstructions, if any

Start the engine with the throttle lever in the start/oper-

ation position

Hold the product firmly to the ground when starting the

engine

Failure to observe the precautions could cause an accident

or injury, or even lead to a fatality.

Once the engine has started, check for abnormal vi-

brations and sounds

Check that there are no abnormal vibrations or sounds

once the engine starts. Do not use the product if there

are abnormal vibrations or sounds. Contact your ECHO

DEALER to have it repaired.

Accidents involving parts that fall or shatter off can cause

wounds or serious injury.

Do not touch high temperature or high voltage com-

ponents while the product is running

Do not touch the following high temperature or high volt-

age components while the product is running or for some

time after it stops.

Muffler, cylinder, and other high tempera-

ture components

You could burn yourself if you touch a high

temperature component.

Spark plug, spark plug wire, and other

high voltage components

You could receive an electric shock if you

touch a high voltage component while the

product is running.

Put safety first in the case of fire or smoke

If fire comes from the engine or smoke appears from

any area other than the exhaust vent, first distance

yourself from the product to ensure your physical safe-

ty.

Use a shovel to throw sand or other such

material on the fire to prevent it from

spreading, or put it out with a fire extin-

guisher.

A panicked reaction could result in the fire and

other damage becoming more extensive.

Exhaust fumes are toxic

The exhaust fumes from the engine contain toxic gases.

Do not operate the product indoors or in a plastic green-

house or in other ill ventilated places.

The exhaust fumes could cause poisoning.

Turn off the engine when checking or maintaining

the product

Observe the following precautions when checking and

maintaining your product after use:

Turn the engine off and do not attempt to check or main-

tain the product until the engine has cooled

You could burn yourself.

Remove the spark plug cap before performing checks

and maintenance

An accident could occur if the product starts unexpectedly.

Checking the spark plug

Observe the following precautions when checking the

spark plug.

If the electrodes or terminals are worn, or if there are

cracks in the ceramics, replace them with new parts.

The spark test (for checking whether the spark plug is

sparking) must be carried out by a professional. Please

ask your ECHO DEALER.

The spark test must not be carried out in proximity of

the spark plug hole.

The spark test must not be performed in places where

there are fuel spills or inflammable gases

You must not touch the

metal parts of the spark

plug

The spark plug could ig-

nite a fire or give you an

electric shock.

9

For safe use of your product

Handling the product

General precautions

WARNING

Operator's manual

Be careful to read the operator's manual

properly before using your product in or-

der to ensure correct operation.

Failure to do so could lead to an accident or

serious injury.

Do not use the product for anything

other than its intended purpose

You must not use the product for any purpose other

than those described in the operator's manual.

To do so could lead to an accident or serious injury.

Do not modify the product

You must not modify the product.

To do so could lead to an accident or serious injury. Any

malfunction resulting from a modification to the product will

not be covered by the manufacturer's warranty.

Do not use the product unless it has been checked

and maintained

You must not use the product unless it has been

checked and maintained. Always ensure that the prod-

uct is checked and maintained on a regular basis.

Failure to do so could lead to an accident or serious injury.

Loaning or assigning your product

When loaning your product to another party, ensure

that the person borrowing the product receives the op-

erator's manual along with it.

If you assign your product to another party, please en-

close the operator's manual with the product when

handing it over.

Failure to do so could lead to an accident or serious injury.

Being prepared in case of an injury

In the unlikely event of an accident or injury, please ensure

that you are prepared.

First aid kit

Towels and wipes (to stop any bleeding)

Whistle or mobile phone (for calling outside help)

If you are unable to perform first aid or call for outside help,

the injury could worsen.

10

For safe use of your product

Precautions for use

WARNING

Users of the product

The product should not be used by:

people who are tired

people who have taken alcohol

people who are on medication

people who are pregnant

people who are in poor physical

condition

people who have not read the op-

erator's manual

children

Failure to observe these instruc-

tions could lead to an accident.

Environment of use and operation

Do not use the product in places where there is no sure

foothold, such as on steep slopes or after rainfall, as

such places are slippery and dangerous.

Do not operate the product at night or in dark places

with poor visibility.

A serious injury could result if you fall or slip, or fail to oper-

ate the product correctly.

Using the product

When using the product, pay special attention to observe

the following precautions.

Do not allow people who are irrelevant to the work con-

ducted or animals to be in the worksite.

Do not point the blower pipe at people or animals.

Do not use the product in places where there is no sure

foothold.

Hold the arm tightly.

Avoid using the product late at night or early in the

morning so that the neighbors will not be disturbed by

noise.

Failure to observe these instructions could lead to an acci-

dent or injury.

Turn off the engine when moving around

When moving around in the situations described below,

turn off the engine and move with the product shouldered.

Moving to the place where you are working

Moving to another area while you are working

Leaving the place where you have been working

Failure to observe these precautions could cause burns or

serious injury.

When transporting the product by car, empty the fuel

tank, put the product in the upright position, and secure

it firmly in place to prevent it from moving around.

Travelling by car with fuel in the fuel tank could lead to a fire.

Be careful not to get caught in the fan

Be careful not to get your hair caught in the fan.

Never put your hand in between the engine and the

backpack frame when the product is in operation.

The wind pressure from the fan could make your hand get

caught in the fan, resulting in a serious injury.

Vibration and cold

It is believed that a condition called Raynaud's Phenome-

non which affects the fingers of certain individuals may be

brought about by exposure to vibration and cold. Expo-

sure to vibration and cold may cause tingling and burning,

followed by loss of colour and numbness in the fingers.

The following precautions are strongly recommended be-

cause the minimum exposure which might trigger the ail-

ment is unknown.

Keep your body warm, especially the head and neck,

feet and ankles, and hands and wrists.

Maintain good blood circulation by performing vigorous

arm exercises during frequent work breaks, and also by

not smoking.

Limit the number of hours of operation.

Try to fill each day with jobs where operating the blower

or other hand-held power equipment is not required.

If you experience discomfort redness and swelling of

the fingers, followed by whitening and loss of feeling,

consult your physician before exposing yourself further

to cold and vibration.

Failure to observe these instructions could result in damage

to your health.

11

For safe use of your product

Protective gear

WARNING

Repetitive stress injuries

It is believed that over-using the muscles and tendons of

the fingers, hands, arms and shoulders may cause sore-

ness, swelling, numbness, weakness and extreme pain to

the areas just mentioned. Certain repetitive hand activities

may put you at a high risk for developing a repetitive

stress injury (RSI).

To reduce the risk of RSI, do the following:

Avoid using your wrist in a bent, extended or twisted

position.

Take periodic breaks to minimize repetition and rest

your hands. Reduce the speed and force in which you

do the repetitive movement.

Do exercises to strengthen hand and arm muscles.

See a doctor if you feel tingling, numbness or pain in

your fingers, hands, wrists or arms. The sooner RSI is

diagnosed, the more likely permanent nerve and muscle

damage can be prevented.

Failure to observe these instructions could result in damage

to your health.

Turn off the engine immediately if anything goes

wrong

Turn off the engine immediately if the product suddenly

starts to emit abnormal sounds or vibrate abnormally.

The product cannot be used when it suffers from abnor-

mal vibration or sounds.

Contact your ECHO DEALER for repair.

Continuing to use parts when they are damaged could lead

to an accident or serious injury.

WARNING

Wear protective gear

Wear appropriate work clothes and protective gear

when working with the power blower. Above all, make

sure to wear safety goggles, a dust mask, and ear muffs

at all times while working.

Without the protective gear, you could inhale the debris or

dust blown away or get them in your eyes, which could lead

to an accident or injury.

a Head protection (helmet): Protects the head

b Ear muffs or ear plugs: Protect the hearing

c Safety goggles: Protect the eyes

d Dust mask

e Safety gloves: Protect the hands from cold and vibration

f Work clothes that fit (long sleeves, long trousers): Pro-

tect the body

g Heavy duty, non-slip protective boots (with toecaps) or

non-slip work shoes (with toecaps): Protect the feet

Failure to observe these precautions could result in damage

to your sight or hearing, or lead to a serious injury.

Wear proper clothing.

Do not wear ties, jewellery, or loose, dangling clothing which could be

caught in the unit. Do not wear open toed footwear, or go bare-foot or

barelegged. In certain situations, total face and head protection may be re-

quired.

Failure to observe these precautions could result in damage to your sight or

hearing, or lead to a serious injury.

12

Packing list

The following parts are packed separately in the packing box.

When you have unpacked the box, please check the parts that it contains.

Contact your ECHO DEALER if anything is missing or broken.

Number Part name Quantity Number Part name Quantity

(1) Power Head 1 (5) Blower Pipe(Main Pipe) 1

(2) Vacuum Tube 1 (6) Blower Pipe(Fan Head Nozzle) 1

(3) Vacuum Elbow 1 (7) Operator's Manual 1

(4) Debris Bag 1 (8) T-Wrench 1

13

Description

1. Stop switch "SLIDE SWITCH" mounted on top of handle.

Push forward to start and run. Slide back to stop.

2. Spark plug Provides spark to ignite fuel mixture.

3. Air cleaner Contains replaceable air filter element.

4. Fuel tank Contains fuel and fuel filter.

5. Fuel tank cap Covers and seals fuel tank.

6. Starter handle The grip of the starter, for starting the en-

gine.("ES"START)

7. Spark arrestor - Catalytic muffler / Muffler The muffler

or catalytic muffler controls exhaust noise and emission.

The spark arrestor screen prevents hot, glowing parti-

cles of carbon from leaving the muffler. Keep exhaust

area clear of flammable debris.

8. Choke Choke is located on top of the air cleaner. Move

choke lever to position to close choke for cold start-

ing. Move choke lever to position to open choke.

9. Purge bulb Pumping purge bulb before starting engine

draws fresh fuel from the fuel tank, purging air from the

carburetor. Pump purge bulb until fuel is visible and

flows freely in the clear fuel tank return line. Pump

purge bulb an additional 4 or 5 times.

10. Blower pipes Exclusive positive locking system.

11. Throttle position lever Pull back to increase engine

speed. Friction washers maintain throttle lever setting.

12. Throttle trigger Spring loaded to return to idle when re-

leased. During acceleration, press trigger gradually for

best operating technique.

13. Serial number label Lists model number and serial

number of unit.

14. Locking ring Locks blower pipe.

15. Vacuum tube Sucks in materials to be shredded.

16. Vacuum elbow Discharges shredded material.

17. Debris bag Collects shredded material.

14

Before you start

Before yo u start

Assembly

Install vacuum tube 1. Turn knob counter clockwise until hinged housing cover is

free to open for vacuum tube installation.

2. Opening housing cover, slide recess (G) on vacuum tube

into locking rib (H) , and turn the vacuum tube clockwise so

that it would be locked.

Install debris bag

1. Stand unit upright on blower base.

2. Release locking ring with a coin or screwdriver, and rotate so

that lock symbol (A) is at top of ring.

WARNING

Read the operator's manual carefully to ensure that you assemble the product correctly.

Never perform maintenance or assembly procedures with engine running.

Using a product that has been incorrectly assembled could lead to an accident or serious injury.

1. Knob

1. Vacuum tube 2. Housing cover

NOTE

Engine will not start/operate unless safety interlock switch (I) is

activated by the vacuum tube.

1. Locking ring

15

Before you start

3. Align locking ribs (J) on vacuum elbow with recesses (B) in

locking ring, and slide vacuum elbow into locking ring.

4. After pushing vacuum elbow all the way in fan case so that

line (K) will meet locking ring, rotate locking ring clockwise

1/8 turn to lock vacuum elbow in place.

5. Place debris bag opening over flared end of vacuum elbow,

and cinch debris bag securely at the position (L) with Velcro

strap.

Install blower pipes for blower usage

1. Stand unit upright on blower base.

2. Release locking ring with a coin or screwdriver, and rotate so

that lock symbol (A) is at top of ring.

1. Vacuum elbow

1. Locking ring

1. Debris bag

16

Before you start

3. Align locking ribs (C) on the blower pipe(main pipe) with re-

cesses (B) in locking ring, and slide the blower pipe(main

pipe) into locking ring.

4. After pushing upper blower all the way in fan case so that

line (D) will meet locking ring, rotate locking ring clockwise

1/8 turn to lock the blower pipe(main pipe) in place.

5. Align tabs (F) with grooves (E) and slide the blower pipe(fan

head nozzle) over the blower pipe(main pipe) until there is

light resistance.

6. Assemble the blower pipe(fan head nozzle) onto the blower

pipe(main pipe) until you feel light resistance. Do not force

connection. Hold the blower pipe(main pipe), and turn the

blower pipe(fan head nozzle) clockwise, engaging positive

locking channels until connection is firm. Do not force con-

nection.

Remove blower pipes 1. Release locking ring with a coin or screwdriver, and rotate

ring so that lock symbol (A) is at top of ring.

2. Remove pipes from locking ring.

1. Locking ring

1. Blower pipe(main pipe)

NOTE

Blower use will eventually loosen pipe connections. Exclusive

positive locking system allows pipes to be tightened. If loosen-

ing occurs, remove the blower pipe(fan head nozzle) and in-

stall according to instructions 5 & 6.

1. Blower pipe(main pipe) 2. Blower pipe(fan head

nozzle)

1. Blower pipe(main pipe)

1. Blower pipe(main pipe) 2. Locking ring

17

Before you start

Preparing the fuel

Fuel Fuel is a mixture of regular grade petrol and an air-cooled 2-

stroke engine oil of reputable brand name.

Minimum 89 Octane unleaded petrol is recommended. Do not

use fuel containing methyl alcohol or more than 10 % of ethyl

alcohol.

Recommended mixture ratio; 50 : 1 (2 %) for ISO-L-EGD

Standard (ISO/CD 13738), JASO FC,FD grade and ECHO

Premium 50 : 1 oil.

- Do not mix directly in engine fuel tank.

- Avoid spilling petrol or oil. Spilling fuel should always be

wiped up.

- Handle petrol with care, it is highly inflammable.

- Always store fuel in approved container.

Fuel supply Always refuel in a well ventilated location. Do not pour fuel in-

doors.

Place the product and the refuelling tank on the ground when

performing the refuelling operation. Do not refuel the product

on the loading platform of a truck, or in other such places.

Always ensure that the fuel level remains below the shoulder

level of the fuel tank when refuelling.

There is a difference in pressure between the fuel tank and the

outside air. When refuelling, loosen the fuel tank cap slightly to

eliminate the difference in pressure.

Always wipe up any fuel spills.

Move at least 3m away from where you refueled before you

start the engine.

Keep the refuelling tank in a shaded area away from fire.

DANGER

Fuel is highly inflammable and there is a risk of fire if it is handled incorrectly. Carefully read

and observe the precautions in the section of this manual titled "For safe use of your prod-

uct".

Once the refuelling is complete, securely tighten the fuel tank cap and do not forget to

check that there are no leaks or discharges of fuel from the fuel pipe, fuel system grommets,

or around the fuel tank cap. If you do find fuel leaks or discharges, stop using the product

immediately and contact your ECHO DEALER to have it repaired.

If the fuel ignites, it could cause burns and fire.

CAUTION

There is difference in pressure between the fuel tank and the outside air. When refuelling, loosen the fuel tank cap

slightly to eliminate the difference in pressure.

Otherwise, fuel may get spewed.

NOTE

Stored fuel ages. Do not mix more fuel than you expect use in thirty (30) days. Do not mix directly in fuel tank.

1. Fuel tank 2. Shoulder level

18

Engine operation

Starting the engine

Starting a cold engine Recoil starter: Use short pulls - only 1/2-2/3 of rope length for

starting. Do not allow the rope to snap back in. Always hold

the unit firmly.

1. Stop Switch

Move stop switch away from the STOP position.

2. Throttle Position Lever

Move throttle position lever midway between idle and full

throttle positions.

3. Choke

Move choke to " " position.

4. Purge Bulb

Pump purge bulb until fuel is visible and flows freely in the

clear fuel tank return line.

5. Recoil Starter

Place the unit on a flat, clear area. Firmly grasp throttle grip

with left hand and rapidly pull recoil starter handle/rope until

engine fires , or maximum 5 pulls.

6. Choke

Move choke to " " position and if necessary, restart engine.

After engine warm up, gradually depress throttle trigger to in-

crease engine RPM to operating speed.

WARNING

When starting the engine, observe the precautions described from Page 4 in the section "For safe use of your prod-

uct" to ensure that you operate the product correctly.

Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.

NOTE

Pull out the starter grip gently at first, and then more rapidly. Do not pull the starter rope out to more than 2/3 of its length.

Do not let go of the starter grip as it returns.

To start the engine, return the choke knob when you hear the first explosion-like sound and pull on the starter grip again. Be

careful not to miss the first explosion-like sound.

1. Stop switch 2. Throttle position lever

1. Choke 2. Purge bulb

1. Recoil starter

1. Choke

NOTE

If engine does not start after 5 pulls, repeat instructions 3-6.

NOTE

Allow engine to warm up before use.

La pagina sta caricando ...

Echo PB-255ES Manuale utente

Questo manuale è adatto anche per

Echo PB-255ES Manuale utente

in altre lingue

Documenti correlati

Altri documenti