Gigabyte H81M-H M.2 Manuale del proprietario

Marca: Gigabyte

Modello: H81M-H M.2

Tipo: Manuale del proprietario

H81M-H M.2

User's Manual

Rev. 1001

GIGABYTE will reduce paper use in order to fulll the responsibilities of a global citizen.

Also, to reduce the impacts on global warming, the packaging materials of this product

are recyclable and reusable. GIGABYTE works with you to protect the environment.

For more product details, please visit GIGABYTE's website.

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without

prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

For detailed product information, carefully read the User's Manual.

For quick set-up of the product, refer to the Quick Installation Guide on GIGABYTE's

website.

https://download.gigabyte.com/FileList/Manual/mb_manual_installation-guide_103.pdf?m=sw

For product-related information, check on our website at: https://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0"

means the revision of the motherboard is 1.0. Check your motherboard revision before updating

motherboard BIOS, drivers, or when looking for technical information.

Example:

- 3 -

Table of Contents

Chapter 1 Product Introduction .......................................................................................4

1-1 Motherboard Layout ......................................................................................... 4

Chapter 2 Hardware Installation .....................................................................................5

2-1 Installation Precautions .................................................................................... 5

2-2 Product Specications ...................................................................................... 6

2-3 Installing the CPU ............................................................................................ 8

2-4 Installing the Memory ....................................................................................... 8

2-5 Installing an Expansion Card ........................................................................... 9

2-6 Back Panel Connectors .................................................................................... 9

2-7 Internal Connectors ........................................................................................ 11

Chapter 3 BIOS Setup ..................................................................................................17

3-1 Startup Screen ............................................................................................... 17

3-2 M.I.T. .............................................................................................................. 18

3-3 System Information ........................................................................................ 23

3-4 BIOS Features ............................................................................................... 24

3-5 Peripherals ..................................................................................................... 27

3-6 Power Management ....................................................................................... 30

3-7 Save & Exit ..................................................................................................... 32

Chapter 4 Installing the Operating System and Drivers ................................................ 33

Regulatory Notices .................................................................................................... 34

Contact Us ................................................................................................................ 35

- 4 -

KB_MS CPU_FAN

SYS_FAN

LGA1150

ATX

H81M-H M.2

F_AUDIO

AUDIO

DDR3_1

DDR3_2

BAT

ATX_12V

COM

Intel® H81

R_USB30

CODEC

CLR_CMOS

M_BIOS

VGA

HDMI

USB_LAN

PCIEX16

M2A

PCIEX1

iTE®

Super I/O

Realtek®

GbE LAN

F_USB1

TPM

F_USB2

F_PANEL

SATA2 3

SATA3 1

1-1 Motherboard Layout

Chapter 1 Product Introduction

Temperature sensor

- 5 -

2-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become

damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's

manual and follow these procedures:

•Prior to installation, make sure the chassis is suitable for the motherboard.

•Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

•Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

•When connecting hardware components to the internal connectors on the motherboard, make

sure they are connected tightly and securely.

•When handling the motherboard, avoid touching any metal leads or connectors.

•It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,

keep your hands dry and rst touch a metal object to eliminate static electricity.

•Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

•Before connecting or unplugging the power supply cable from the motherboard, make sure

the power supply has been turned off.

•Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

•Before using the product, please verify that all cables and power connectors of your hardware

components are connected.

•To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

•Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

•Do not place the computer system on an uneven surface.

•Do not place the computer system in a high-temperature or wet environment.

•Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

•If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

•If you use an adapter, extension power cable, or power strip, ensure to consult with its

installation and/or grounding instructions.

Chapter 2 Hardware Installation

- 6 -

2-2 ProductSpecications

CPU Support for Intel® Core™ i7 processors/Intel® Core™ i5 processors/

Intel® Core™ i3 processors/Intel® Pentium® processors/Intel® Celeron® processors

in the LGA1150 package

(Go to GIGABYTE's website for the latest CPU support list.)

L3 cache varies with CPU

Chipset Intel® H81 Express Chipset

MEMORY 2 x DDR3 DIMM sockets supporting up to 16 GB of system memory

* Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical

memory is installed, the actual memory size displayed will be less than the size of

the physical memory installed.

Dual channel memory architecture

Support for DDR3 1600/1333 MHz memory modules

Support for non-ECC memory modules

Support for Extreme Memory Prole (XMP) memory modules

(Go to GIGABYTE's website for the latest supported memory speeds and memory

modules.)

Onboard

Graphics

Integrated Graphics Processor-Intel® HD Graphics support:

- 1 x D-Sub port, supporting a maximum resolution of 1920x1200

- 1 x HDMI port, supporting a maximum resolution of 4096x2160

* Support for HDMI 1.4a version.

- Maximum shared memory of 1 GB

Audio Realtek® Audio CODEC

High Denition Audio

2/4/5.1/7.1-channel

* You can change the functionality of an audio jack using the audio software. To

congure 7.1-channel audio, access the audio software for audio settings.

LAN Realtek® GbE LAN chip (1 Gbps/100 Mbps/10 Mbps)

Expansion Slots 1 x PCI Express x16 slot, running at x16

1 x PCI Express x1 slot

(The PCI Express slots conform to PCI Express 2.0 standard.)

Storage Interface Chipset:

- 1 x M.2 connector (Socket 3, M key, type 2280 SATA and PCIe 2.0 x4/x2 SSD

support)

- 2 x SATA 6Gb/s connectors (SATA3 0/1)

- 2 x SATA 3Gb/s connectors (SATA2 2/3)

* The M2A connector shares bandwidth with the SATA3 0 connector. The SATA3 0

connector will become unavailable when an SATA SSD is installed in the M2A connector.

Refer to "2-7 Internal Connectors," "8) M2A (M.2 Socket 3 Connector)," for the installation

notices for the M.2 and SATA connectors.

USB Chipset:

- 2 x USB 3.0/2.0 ports on the back panel

- 6 x USB 2.0/1.1 ports (2 ports on the back panel, 4 ports available through

the internal USB headers)

Internal

Connectors

1 x 24-pin ATX main power connector

1 x 4-pin ATX 12V power connector

1 x M.2 Socket 3 connector

2 x SATA 6Gb/s connectors

2 x SATA 3Gb/s connectors

1 x CPU fan header

1 x system fan header

- 7 -

Internal

Connectors

1 x front panel header

1 x front panel audio header

2 x USB 2.0/1.1 headers

1 x serial port header

1 x Clear CMOS jumper

1 x Trusted Platform Module (TPM) header

Back Panel

Connectors

1 x PS/2 mouse port

1 x PS/2 keyboard port

1 x D-Sub port

1 x HDMI port

2 x USB 3.0/2.0 ports

2 x USB 2.0/1.1 ports

1 x RJ-45 port

3 x audio jacks

I/O Controller iTE® I/O Controller Chip

Hardware

Monitor

Voltage detection

Temperature detection

Fan speed detection

Overheating warning

Fan fail warning

Fan speed control

* Whether the fan speed control function is supported will depend on the fan you install.

BIOS 1 x 32 Mbit ash

Use of licensed AMI UEFI BIOS

PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0

Unique Features Support for Q-Flash

Support for APP Center

* Available applications in APP Center may vary by motherboard model. Supported

functions of each application may also vary depending on motherboard specications.

- @BIOS

- EasyTune

- EZ Setup

- USB Blocker

- Smart TimeLock

- Smart Recovery 2

Support for ON/OFF Charge

Bundled

Software

Norton® Internet Security (OEM version)

LAN bandwidth management software

Operating

System Support for Windows 10/7

Form Factor Micro ATX Form Factor; 23.0cm x 17.5cm

* GIGABYTE reserves the right to make any changes to the product specications and product-related information without

prior notice.

&Please visit the SERVICE/SUPPORT\Utility page on GIGABYTE's website to download the latest version

of apps.

https://www.gigabyte.com/Support/Utility/Motherboard?m=ut

- 8 -

&Please visit GIGABYTE's website for details on hardware installation.

https://www.gigabyte.com/WebPage/210/quick-guide.html?m=sw

2-3 Installing the CPU

Read the following guidelines before you begin to install the CPU:

•Make sure that the motherboard supports the CPU.

(Go to GIGABYTE's website for the latest CPU support list.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

CPU to prevent hardware damage.

•Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may

locate the notches on both sides of the CPU and alignment keys on the CPU socket.)

•Apply an even and thin layer of thermal grease on the surface of the CPU.

•Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage

of the CPU may occur.

•Set the CPU host frequency in accordance with the CPU specications. It is not recommended

that the system bus frequency be set beyond hardware specications since it does not meet the

standard requirements for the peripherals. If you wish to set the frequency beyond the standard

specications, please do so according to your hardware specications including the CPU, graphics

card, memory, hard drive, etc.

Installing the CPU

Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

Alignment KeyAlignment Key

LGA1150 CPU Socket

Pin One Corner of the CPU Socket

Notch

LGA1150 CPU

Triangle Pin One Marking on the CPU

Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load

plate automatically during the process of re-engaging the lever after you insert the CPU.

2-4 Installing the Memory

DualChannelMemoryConguration

This motherboard provides two DDR3 memory sockets and supports Dual Channel Technology. After the memory

is installed, the BIOS will automatically detect the specications and capacity of the memory. Enabling Dual

Channel memory mode will double the original memory bandwidth.

Read the following guidelines before you begin to install the memory:

•Make sure that the motherboard supports the memory. It is recommended that memory of the

same capacity, brand, speed, and chips be used.

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

memory to prevent hardware damage.

•Memory modules have a foolproof design. A memory module can be installed in only one direction.

If you are unable to insert the memory, switch the direction.

- 9 -

PS/2 Keyboard and PS/2 Mouse Port

Use the upper port (green) to connect a PS/2 mouse and the lower port (purple) to connect a PS/2 keyboard.

D-Sub Port

The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 1920x1200

(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports

D-Sub connection to this port.

HDMI Port

The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD

Master Audio formats. It also supports up to 192KHz/24bit 7.1-channel LPCM

audio output. You can use this port to connect your HDMI-supported monitor. The maximum supported

resolution is 4096x2160, but the actual resolutions supported are dependent on the monitor being used.

After installing the HDMI device, make sure to set the default sound playback device to HDMI. (The

item name may differ depending on your operating system.)

2-5 Installing an Expansion Card

2-6 Back Panel Connectors

Read the following guidelines before you begin to install an expansion card:

•Make sure the motherboard supports the expansion card. Carefully read the manual that came

with your expansion card.

•Always turn off the computer and unplug the power cord from the power outlet before installing an

expansion card to prevent hardware damage.

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.

1. Dual Channel mode cannot be enabled if only one memory module is installed.

2. When enabling Dual Channel mode with two memory modules, it is recommended that memory of

the same capacity, brand, speed, and chips be used for optimum performance.

The two memory sockets are divided into two channels and each channel has one memory socket as following:

Channel A: DDR3_1

Channel B: DDR3_2

•When removing the cable connected to a back panel connector, rst remove the cable from your

device and then remove it from the motherboard.

•When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent

an electrical short inside the cable connector.

- 10 -

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specication. Use this port for USB devices.

Line In/Rear Speaker Out (Blue)

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out/Front Speaker Out (Green)

The line out jack.

Mic In/Center/Subwoofer Speaker Out (Pink)

The Mic in jack.

&Please visit GIGABYTE's website for details on conguring the audio software.

https://www.gigabyte.com/WebPage/697/realtek897-audio.html

You can change the functionality of an audio jack using the audio software. To congure 7.1-channel

audio, access the audio software for audio settings.

USB 3.0/2.0 Port

The USB 3.0 port supports the USB 3.0 specication and is compatible to the USB 2.0/1.1 specication.

Use this port for USB devices.

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following

describes the states of the LAN port LEDs.

Speed LED:

State Description

Orange 1 Gbps data rate

Green 100 Mbps data rate

Off 10 Mbps data rate

Activity LED:

State Description

Blinking Data transmission or receiving is occurring

Off No data transmission or receiving is occurring

Speed LED Activity LED

LAN Port

Audio Jack Congurations:

Jack Headphone/

2-channel 4-channel 5.1-channel 7.1-channel

Line In/Rear Speaker Out a a a

Line Out/Front Speaker Out a a a a

Mic In/Center/Subwoofer Speaker Out a a

Front Panel Line Out/

Side Speaker Out a

- 11 -

Read the following guidelines before connecting external devices:

•First make sure your devices are compliant with the connectors you wish to connect.

•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

•After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

1 3

10 4 14913

1) ATX_12V

2) ATX

3) CPU_FAN

4) SYS_FAN

5) BAT

6) SATA3 0/1

7) SATA2 2/3

8) M2A

9) F_PANEL

10) F_ AUDIO

11) F_USB1/F_USB2

12) COM

13) TPM

14) CLR_CMOS

2-7 Internal Connectors

- 12 -

CPU_FAN/SYS_FAN:

Pin No. Denition

1 GND

2Voltage Speed Control

3Sense

4PWM Speed Control

•Be sure to connect fan cables to the fan headers to prevent your CPU and system from

overheating. Overheating may result in damage to the CPU or the system may hang.

•These fan headers are not conguration jumper blocks. Do not place a jumper cap on the headers.

SYS_FAN

CPU_FAN

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

1/2) ATX_12V/ATX (2x2 12V Power Connector and 2x12 Main Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components

on the motherboard. Before connecting the power connector, rst make sure the power supply is turned

off and all devices are properly installed. The power connector possesses a foolproof design. Connect the

power supply cable to the power connector in the correct orientation.

The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,

the computer will not start.

3/4) CPU_FAN/SYS_FAN (Fan Headers)

All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.

When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is

the ground wire). The speed control function requires the use of a fan with fan speed control design. For

optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption

be used (500W or greater). If a power supply is used that does not provide the required power, the result can

lead to an unstable or unbootable system.

ATX_12V:

Pin No. Denition

1 GND

2 GND

3+12V

4+12V

ATX_12V

DEBUG

PORT

G.QBOFM

131

2412

ATX

ATX:

Pin No. Denition Pin No. Denition

13.3V 13 3.3V

23.3V 14 -12V

3 GND 15 GND

4+5V 16 PS_ON (soft On/Off)

5 GND 17 GND

6+5V 18 GND

7 GND 19 GND

8Power Good 20 -5V

95VSB (stand by +5V) 21 +5V

10 +12V 22 +5V

11 +12V (Only for 2x12-pin

ATX)

23 +5V (Only for 2x12-pin ATX)

12 3.3V (Only for 2x12-pin

ATX)

24 GND (Only for 2x12-pin ATX)

- 13 -

To enable hot-plugging for the SATA ports, refer to Chapter 3, "BIOS Setup," "Peripherals\SATA

Conguration," for more information.

5) BAT (Battery)

The battery provides power to keep the values (such as BIOS congurations, date, and time information)

in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low

level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:

1. Turn off your computer and unplug the power cord.

2. Gently remove the battery from the battery holder and wait for one minute. (Or use a metal

object like a screwdriver to touch the positive and negative terminals of the battery holder,

making them short for 5 seconds.)

3. Replace the battery.

4. Plug in the power cord and restart your computer.

•Always turn off your computer and unplug the power cord before replacing the battery.

•Replace the battery with an equivalent one. Damage to your devices may occur if the battery is replaced

with an incorrect model.

•Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain

about the battery model.

•When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the battery

(the positive side should face up).

•Used batteries must be handled in accordance with local environmental regulations.

6) SATA3 0/1 (SATA 6Gb/s Connectors)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA

1.5Gb/s standard. Each SATA connector supports a single SATA device.

7) SATA2 2/3 (SATA 3Gb/s Connectors)

The SATA connectors conform to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard.

Each SATA connector supports a single SATA device.

Pin No. Denition

1 GND

2TXP

3TXN

4 GND

5RXN

6RXP

7 GND

Pin No. Denition

1 GND

2TXP

3TXN

4 GND

5RXN

6RXP

7 GND

SATA3 1 0

SATA2 3 2

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

- 14 -

8) M2A (M.2 Socket 3 Connector)

The M.2 connector supports M.2 SATA SSDs or M.2 PCIe SSDs.

Follow the steps below to correctly install an M.2 SSD in the

M.2 connector.

Step 1:

Pull the clip's tab up and out of the mounting hole. Slide the

M.2 SSD into the connector at an angle.

Step 2:

Press the M.2 SSD down and then secure it by pressing the

clip's tab into the mounting hole.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

_S

SS_F 

_

_ F 

_SB

F_

80 60 42

SATA3 0 SATA3 1 SATA2 2 SATA2 3

M.2 SATA SSD raaa

M.2 PCIe SSD aaaa

No M.2 SSD Installed aaaa

a: Available, r: Not available

Connector

Type of

M.2 SSD

9) F_PANEL (Front Panel Header)

Connect the power switch, reset switch, speaker, and system status indicator on the chassis to this header

according to the pin assignments below. Note the positive and negative pins before connecting the cables.

•PW (Power Switch):

Connects to the power switch on the chassis front panel. You may

congure the way to turn off your system using the power switch

(refer to Chapter 3, "BIOS Setup," "Power Management," for more

information).

•SPEAK (Speaker):

Connects to the speaker on the chassis front panel. The system reports

system startup status by issuing a beep code. One single short beep

will be heard if no problem is detected at system startup.

•HD (Hard Drive Activity LED):

Connects to the hard drive activity LED on the chassis front panel. The

LED is on when the hard drive is reading or writing data.

•PLED/PWR_LED (Power LED):

System Status LED

S0 On

S3/S4/S5 Off

Connects to the power status indicator

on the chassis front panel. The LED is on

when the system is operating. The LED is

off when the system is in S3/S4 sleep state

or powered off (S5).

The front panel design may differ by chassis. A front panel module mainly consists of power switch,

reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis

front panel module to this header, make sure the wire assignments and the pin assignments are

matched correctly.

•RES (Reset Switch):

Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the

computer freezes and fails to perform a normal restart.

•CI (Chassis Intrusion Header):

Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has been

removed. This function requires a chassis with a chassis intrusion switch/sensor.

•NC: No connection.

Power LED

CI-

CI+

PLED-

PW-

SPEAK+

SPEAK-

PLED+

PW+

Power LED

HD-

RES+

HD+

RES-

Hard Drive

Activity LED

Reset

Switch Chassis Intrusion

Header

Power Switch Speaker

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

_S

SS_F 

_

_ F 

_SB

F_

PWR_LED-

PWR_LED+

PWR_LED-

The M2A connector shares bandwidth with the SATA3 0 connector. Refer to the following tables for details.

- 15 -

10) F_AUDIO (Front Panel Audio Header)

The front panel audio header supports High Denition audio (HD). You may connect your chassis front

panel audio module to this header. Make sure the wire assignments of the module connector match the

pin assignments of the motherboard header. Incorrect connection between the module connector and the

motherboard header will make the device unable to work or even damage it.

Pin No. Denition Pin No. Denition

1 MIC L 6 MIC Detection

2 GND 7 SENSE_SEND

3 MIC R 8 No Pin

4 NC 9 Head Phone L

5Head Phone R 10 Head Phone Detection

Some chassis provide a front panel audio module that has separated connectors on each wire

instead of a single plug. For information about connecting the front panel audio module that has

different wire assignments, please contact the chassis manufacturer.

11) F_USB1/F_USB2 (USB 2.0/1.1 Headers)

The headers conform to USB 2.0/1.1 specication. Each USB header can provide two USB ports via an

optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

Pin No. Denition Pin No. Denition

1Power (5V) 6USB DY+

2Power (5V) 7 GND

3USB DX- 8 GND

4USB DY- 9No Pin

5USB DX+ 10 NC

Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord

from the power outlet to prevent damage to the USB bracket.

Pin No. Denition Pin No. Denition

1 NDCD- 6 NDSR-

2NSIN 7NRTS-

3NSOUT 8NCTS-

4 NDTR- 9 NRI-

5 GND 10 No Pin

12) COM (Serial Port Header)

The COM headers can provide one serial port via an optional COM port cable. For purchasing the optional

COM port cable, please contact the local dealer.

- 16 -

14) CLR_CMOS (Clear CMOS Jumper)

Use this jumper to clear the BIOS conguration and reset the CMOS values to factory defaults. To clear

the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.

Open: Normal

Short: Clear CMOS Values

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

B 

USB0_B

B_

B_

F_USB3

 F_USB303



_



_3U

S_

_S

SS_F 

_

_ F 

_SB

F_

Pin No. Denition Pin No. Denition Pin No. Denition

1 LCLK 8 LAD2 15 SB3V

2 GND 9 VCC3 16 SERIRQ

3 LFRAME 10 LAD1 17 GND

4No Pin 11 LAD0 18 NC

5LRESET 12 GND 19 NC

6 NC 13 NC 20 SUSCLK

7 LAD3 14 ID

13) TPM (Trusted Platform Module Header)

You may connect a TPM (Trusted Platform Module) to this header.

•Always turn off your computer and unplug the power cord from the power outlet before clearing

the CMOS values.

•After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or

manually congure the BIOS settings (refer to Chapter 3, "BIOS Setup," for BIOS congurations).

- 17 -

Chapter 3 BIOS Setup

3-1 Startup Screen

The following startup Logo screen will appear when the computer boots.

Function Keys

•When the system is not stable as usual, select the Load Optimized Defaults item to set your system to its defaults.

•The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.

On the main menu of the BIOS Setup program, press arrow keys to move among the items and press <Enter>

to accept or enter a sub-menu. Or you can use your mouse to select the item you want.

•Because BIOS ashing is potentially risky, if you do not encounter problems using the current version of BIOS,

it is recommended that you not ash the BIOS. To ash the BIOS, do it with caution. Inadequate BIOS ashing

may result in system malfunction.

•It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other

unexpected results. Inadequately altering the settings may result in system's failure to boot. If this occurs, try to

clear the CMOS values and reset the board to default values. (Refer to the "Load Optimized Defaults" section in

this chapter or introductions of the battery/clear CMOS jumper in Chapter 2 for how to clear the CMOS values.)

BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the

motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup,

saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows

the user to modify basic system conguration settings or to activate certain system features.

When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to

keep the conguration values in the CMOS.

To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on.

To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility.

•Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.

•@BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the Internet

and updates the BIOS.

- 18 -

3-2 M.I.T.

Whether the system will work stably with the overclock/overvoltage settings you made is dependent

on your overall system congurations. Incorrectly doing overclock/overvoltage may result in damage

to CPU, chipset, or memory and reduce the useful life of these components. This page is for advanced

users only and we recommend you not to alter the default settings to prevent system instability or

other unexpected results. (Inadequately altering the settings may result in system's failure to boot. If

this occurs, clear the CMOS values and reset the board to default values.)

This section provides information on the BIOS version, CPU base clock, CPU frequency, memory frequency,

total memory size, CPU temperature, Vcore, and memory voltage.

`M.I.T. Current Status

This screen provides information on CPU/memory requencies/parameters.

`Advanced Frequency Settings

&Processor Graphics Clock

Allows you to set the onboard graphics clock. (Default: Auto)

&CPU Upgrade (Note)

Allows you to set the CPU frequency. Options may vary depending on the CPU being used. (Default: Auto)

&CPU Clock Ratio

Allows you to alter the clock ratio for the installed CPU.

&CPU Frequency

Displays the current operating CPU frequency.

`Advanced CPU Core Settings

&CPU Clock Ratio, CPU Frequency

The settings above are synchronous to those under the same items on the Advanced Frequency Settings

menu.

&K OC (Note)

Allows for increased performance by using certain CPUs. (Default: Auto)

(Note) This item is present only when you install a CPU that supports this feature. For more information about

Intel® CPUs' unique features, please visit Intel's website.

- 19 -

(Note) This item is present only when you install a CPU that supports this feature. For more information about

Intel® CPUs' unique features, please visit Intel's website.

&CPU PLL Selection

Allows you to set the CPU PLL. Auto lets the BIOS automatically congure this setting. (Default: Auto)

&Filter PLL Level

Allows you to set the Filter PLL. Auto lets the BIOS automatically congure this setting. (Default: Auto)

&Uncore Ratio

Allows you to set the CPU Uncore ratio. The adjustable range is dependent on the CPU being used.

&Uncore Frequency

Displays the current CPU Uncore frequency.

&Intel(R) Turbo Boost Technology (Note)

Allows you to determine whether to enable the Intel® CPU Turbo Boost technology. Auto lets the BIOS

automatically congure this setting. (Default: Auto)

&Turbo Ratio (1-Core Active~4-Core Active) (Note)

Allows you to set the CPU Turbo ratios for different number of active cores. Auto sets the CPU Turbo ratios

according to the CPU specications. (Default: Auto)

&Turbo Power Limit (Watts)

Allows you to set a power limit for CPU Turbo mode. When the CPU power consumption exceeds the

specied power limit, the CPU will automatically reduce the core frequency in order to reduce the power.

Auto sets the settings according to the CPU specications. (Default: Auto)

&Core Current Limit (Amps)

Allows you to set a current limit for CPU Turbo mode. When the CPU current exceeds the specied current

limit, the CPU will automatically reduce the core frequency in order to reduce the current. Auto sets the

settings according to the CPU specications. (Default: Auto)

&No. of CPU Cores Enabled (Note)

Allows you to select the number of CPU cores to enable in an Intel® multi-core CPU (the number of CPU

cores may vary by CPU). Auto lets the BIOS automatically congure this setting. (Default: Auto)

&Hyper-Threading Technology (Note)

Allows you to determine whether to enable multi-threading technology when using an Intel® CPU that

supports this function. This feature only works for operating systems that support multi-processor mode.

Auto lets the BIOS automatically congure this setting. (Default: Auto)

&CPU Enhanced Halt (C1E) (Note)

Enables or disables Intel® CPU Enhanced Halt (C1E) function, a CPU power-saving function in system

halt state. When enabled, the CPU core frequency and voltage will be reduced during system halt state to

decrease power consumption. Auto lets the BIOS automatically congure this setting. (Default: Auto)

&C3 State Support (Note)

Allows you to determine whether to let the CPU enter C3 mode in system halt state. When enabled, the

CPU core frequency and voltage will be reduced during system halt state to decrease power consumption.

The C3 state is a more enhanced power-saving state than C1. Auto lets the BIOS automatically congure

this setting. (Default: Auto)

&C6/C7 State Support (Note)

Allows you to determine whether to let the CPU enter C6/C7 mode in system halt state. When enabled, the

CPU core frequency and voltage will be reduced during system halt state to decrease power consumption.

The C6/C7 state is a more enhanced power-saving state than C3. Auto lets the BIOS automatically congure

this setting. (Default: Auto)

- 20 -

(Note 1) This item is present only when you install a CPU that supports this feature. For more information about

Intel® CPUs' unique features, please visit Intel's website.

(Note 2) This item is present only when you install a CPU and a memory module that support this feature.

`Advanced Memory Settings

&ExtremeMemoryProle(X.M.P.) (Note 2), System Memory Multiplier, Memory Frequency(MHz)

The settings above are synchronous to those under the same items on the Advanced Frequency Settings

menu.

&Memory Boot Mode (Note 2)

Provides memory detection and training methods.

Auto Lets the BIOS automatically congure this setting. (Default)

Enable Fast Boot Skip memory detection and training in some specic criteria for faster memory

boot.

Disable Fast Boot Detect and train memory at every single boot.

&Memory Initialization Mode

Allows you to congure memory timing prole for different frequency memory. Options are: Auto (default),

Normal Speed, High Speed, Extreme Speed.

&Memory Enhancement Settings

Provides three different memory performance enhancement settings: Normal (basic performance), Enhanced

Stability, and Enhanced Performance. (Default: Normal)

&Memory Timing Mode

Manual and Advanced Manual allows the Channel Interleaving, Rank Interleaving, and memory timing

settings below to be congurable. Options are: Auto (default), Manual, Advanced Manual.

&ProleDDRVoltage

When using a non-XMP memory module or ExtremeMemoryProle(X.M.P.) is set to Disabled, the value

is displayed according to your memory specication. When ExtremeMemoryProle(X.M.P.) is set to

Prole1 or Prole2, the value is displayed according to the SPD data on the XMP memory.

&CPU Thermal Monitor (Note 1)

Enables or disables Intel® Thermal Monitor function, a CPU overheating protection function. When enabled,

the CPU core frequency and voltage will be reduced when the CPU is overheated. Auto lets the BIOS

automatically congure this setting. (Default: Auto)

&CPU EIST Function (Note 1)

Enables or disables Enhanced Intel® Speed Step Technology (EIST). Depending on CPU loading, Intel®

EIST technology can dynamically and effectively lower the CPU voltage and core frequency to decrease

average power consumption and heat production. Auto lets the BIOS automatically congure this setting.

(Default: Auto)

&ExtremeMemoryProle(X.M.P.) (Note 2)

Allows the BIOS to read the SPD data on XMP memory module(s) to enhance memory performance when

enabled.

Disabled Disables this function. (Default)

Prole1 Uses Prole 1 settings.

Prole2 (Note 2) Uses Prole 2 settings.

&System Memory Multiplier

Allows you to set the system memory multiplier. Auto sets memory multiplier according to memory SPD

data. (Default: Auto)

&Memory Frequency (MHz)

The rst memory frequency value is the normal operating frequency of the memory being used; the second

is the memory frequency that is automatically adjusted according to the System Memory Multiplier settings.

La pagina sta caricando ...

Gigabyte H81M-H M.2 Manuale del proprietario

Marca: Gigabyte

Modello: H81M-H M.2

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Gigabyte H81M-H M.2 Owner's manual

Gigabyte H81M-H M.2 Manuale del proprietario

Gigabyte H81M-H M.2 Manuale del proprietario

in altre lingue

Documenti correlati