Gigabyte GA-B85N Phoenix-WIFI Manuale del proprietario

Marca: Gigabyte

Modello: GA-B85N Phoenix-WIFI

Tipo: Manuale del proprietario

GA-B85N Phoenix-WIFI

User's Manual

Rev. 2002

12ME-B85NPHW-2002R

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without prior notice.

No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by

any means without GIGABYTE's prior written permission.

In order to assist in the use of this product, carefully read the User's Manual.

For product-related information, check on our website at: http://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the

revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS,

drivers, or when looking for technical information.

Example:

Motherboard

GA-B85N Phoenix-WIFI

Jan. 3, 2014

Jun. 12, 2014

Motherboard

GA-B85N Phoenix-WIFI

Wireless Module Country Approvals:

See the latest safety and regulatory documents at GIGABYTE's website.

- 4 -

Table of Contents

GA-B85N Phoenix-WIFI Motherboard Layout .................................................................5

GA-B85N Phoenix-WIFI Motherboard Block Diagram .....................................................6

Chapter 1 Hardware Installation .....................................................................................7

1-1 Installation Precautions .................................................................................... 7

1-2 Product Specications ...................................................................................... 8

1-3 Installing the CPU .......................................................................................... 10

1-4 Installing the Memory ..................................................................................... 11

1-5 Installing an Expansion Card ......................................................................... 11

1-6 Back Panel Connectors .................................................................................. 11

1-7 Internal Connectors ........................................................................................ 13

Chapter 2 BIOS Setup ..................................................................................................18

2-1 Startup Screen ............................................................................................... 19

2-2 M.I.T. .............................................................................................................. 19

2-3 System Information ........................................................................................ 24

2-4 BIOS Features ............................................................................................... 25

2-5 Peripherals ..................................................................................................... 28

2-6 Power Management ....................................................................................... 30

2-7 Save & Exit ..................................................................................................... 32

Chapter 3 Appendix ......................................................................................................33

Drivers Installation ..................................................................................................... 33

Regulatory Statements .............................................................................................. 34

Contact Us ................................................................................................................ 40

- 5 -

GA-B85N Phoenix-WIFI Motherboard Layout

The box contents above are for reference only and the actual items shall depend on the product package you obtain.

The box contents are subject to change without notice.

Box Contents

5GA-B85N Phoenix-WIFI motherboard

5Wireless module driver disk 5Two SATA cables

5Motherboard driver disk 5I/O Shield

5User's Manual 5One antenna

KB_MS_USB CPU_FANSYS_FAN

LGA1150

ATX

AUDIO

USB_DAC

B_BIOS

DDR3_1

DDR3_2

SATA2

ATX_12V

Intel® B85

USB_HDMI

USB30_LAN

CODEC

F_AUDIO

CLR_CMOS

M_BIOS

PCIEX16

SPDIF_O

iTE®

Super I/O

Intel®

GbE LAN

MSATA

F_USB

F_USB30

F_PANELCOM

BAT

SATA3

0 1

ANTENNA_

BRACKET

DVI

WIFI Module

GA-B85N Phoenix-WIFI

- 6 -

GA-B85N Phoenix-WIFI Motherboard Block Diagram

PS/2 KB/Mouse

LGA1150

CPU

Intel® B85

PCIe CLK

(100 MHz)

CPU CLK+/- (100 MHz)

1 PCI Express x16

Dual BIOS

COM

4 USB 3.0/2.0

7 USB 2.0/1.1

LPC

Bus

DDR3 1600/1333 MHz

LAN

RJ45

PCI Express Bus

PCIe CLK

(100 MHz) Intel®

GbE LAN

1 SATA 3Gb/s

1 mSATA 6Gb/s

3 SATA 6Gb/s

DVI-I

HDMI

DMI 2.0

FDI

x16

Dual Channel Memory

iTE®

Super I/O

For detailed product information/limitation(s), refer to "1-2 Product Specications."

Line Out

MIC

Line In

S/PDIF Out

Side Speaker Out

CODEC

Center/Subwoofer

Speaker Out

Rear Speaker Out

Mini PCIe

(for WiFi Module only)

- 7 -

Chapter 1 Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become

damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's

manual and follow these procedures:

•Prior to installation, make sure the chassis is suitable for the motherboard.

•Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

•Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

•When connecting hardware components to the internal connectors on the motherboard, make

sure they are connected tightly and securely.

•When handling the motherboard, avoid touching any metal leads or connectors.

•It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,

keep your hands dry and rst touch a metal object to eliminate static electricity.

•Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

•Before connecting or unplugging the power supply cable from the motherboard, make sure

the power supply has been turned off.

•Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

•Before using the product, please verify that all cables and power connectors of your hardware

components are connected.

•To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

•Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

•Do not place the computer system on an uneven surface.

•Do not place the computer system in a high-temperature or wet environment.

•Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

•If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

•If you use an adapter, extension power cable, or power strip, ensure to consult with its installation

and/or grounding instructions.

- 8 -

1-2 ProductSpecications

CPU Support for Intel® Core™ i7 processors/Intel® Core™ i5 processors/

Intel® Core™ i3 processors/Intel® Pentium® processors/

Intel® Celeron® processors in the LGA1150 package

(Go to GIGABYTE's website for the latest CPU support list.)

L3 cache varies with CPU

Chipset Intel® B85 Express Chipset

Memory 2 x DDR3 DIMM sockets supporting up to 16 GB of system memory

* Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical

memory is installed, the actual memory size displayed will be less than the size of

the physical memory installed.

Dual channel memory architecture

Support for DDR3 1600/1333 MHz memory modules

Support for non-ECC memory modules

Support for Extreme Memory Prole (XMP) memory modules

(Go to GIGABYTE's website for the latest supported memory speeds and memory

modules.)

Onboard

Graphics

Integrated Graphics Processor:

- 1 x DVI-I port, supporting a maximum resolution of 1920x1200

- 1 x HDMI port, supporting a maximum resolution of 4096x2160

* Support for HDMI 1.4a version.

- Maximum shared memory of 1 GB

Audio Realtek® ALC898 codec

High Denition Audio

2/4/5.1/7.1-channel

Support for S/PDIF Out

LAN Intel® GbE LAN chip (10/100/1000 Mbit)

Wireless

Communication

Module

Wi-Fi 802.11 a/b/g/n/ac, supporting 2.4/5 GHz Dual-Band

Bluetooth 4.0, 3.0+HS, 2.1+EDR

Support for 11ac wireless standard and up to 867 Mbps data rate

* Actual data rate may vary depending on environment and equipment.

Expansion Slots 1 x PCI Express x16 slot, running at x16

(The PCIEX16 slot conforms to PCI Express 3.0 standard.)

1 x mini-PCI Express slot for the wireless communication module

Storage Interface Chipset:

- 3 x SATA 6Gb/s connectors (SATA3 0~2)

- 1 x SATA 3Gb/s connector (SATA2)

- 1 x mSATA 6Gb/s connector

USB Chipset:

- 4 x USB 3.0/2.0 ports (2 ports on the back panel, 2 ports available through

the internal USB header)

- 7 x USB 2.0/1.1 ports (5 ports on the back panel, 2 ports available through

the internal USB header)

Internal

Connectors

1 x 24-pin ATX main power connector

1 x 4-pin ATX 12V power connector

3 x SATA 6Gb/s connectors

1 x SATA 3Gb/s connector

- 9 -

Internal

Connectors

1 x mSATA 6Gb/s connector

1 x CPU fan header

1 x system fan header

1 x front panel header

1 x front panel audio header

1 x S/PDIF Out header

1 x USB 3.0/2.0 header

1 x USB 2.0/1.1 header

1 x serial port header

1 x chassis intrusion header

1 x Clear CMOS jumper

Back Panel

Connectors

1 x PS/2 keyboard/mouse port

1 x DVI-I port

1 x HDMI port

2 x Wi-Fi antenna connectors

2 x USB 3.0/2.0 ports

5 x USB 2.0/1.1 ports

1 x RJ-45 port

1 x optical S/PDIF Out connector

 5 x audio jacks (Center/Subwoofer Speaker Out, Rear Speaker Out, Line In,

Line Out, Mic In)

I/O Controller iTE® I/O Controller Chip

Hardware

Monitor

System voltage detection

CPU/System temperature detection

CPU/System fan speed detection

CPU/System fan speed control

* Whether the fan speed control function is supported will depend on the cooler you

install.

BIOS 2 x 64 Mbit ash

Use of licensed AMI UEFI BIOS

Support for DualBIOS™

PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0

Unique Features Support for Q-Flash

Support for Xpress Install

Support for APP Center

* Available applications in APP Center may differ by motherboard model. Supported

functions of each application may also differ depending on motherboard

specications.

- @BIOS

- EasyTune

- EZ Setup

- USB Blocker

- Smart TimeLock

- Smart Recovery 2

Support for ON/OFF Charge

Support for Wi-Fi Share

Support for Cloud Station

- 10 -

Bundled

Software

Norton® Internet Security (OEM version)

Intel® Rapid Start Technology

Intel® Smart Connect Technology

Intel® Small Business Advantage

cFosSpeed

* To use cFosSpeed in Windows 8.1, please download the latest version from

GIGABYTE's website.

Operating

System Support for Windows 10/8.1/8/7

Form Factor Mini-ITX Form Factor; 17.0cm x 17.0cm

* GIGABYTE reserves the right to make any changes to the product specications and product-related information without

prior notice.

* Please visit the Support & Downloads\Utility page on GIGABYTE's website to check the supported operating system(s)

for the software listed in the "Unique Features" and "Bundled Software" columns.

1-3 Installing the CPU

Read the following guidelines before you begin to install the CPU:

•Make sure that the motherboard supports the CPU.

(Go to GIGABYTE's website for the latest CPU support list.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

CPU to prevent hardware damage.

•Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may

locate the notches on both sides of the CPU and alignment keys on the CPU socket.)

•Apply an even and thin layer of thermal grease on the surface of the CPU.

•Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage

of the CPU may occur.

•Set the CPU host frequency in accordance with the CPU specications. It is not recommended

that the system bus frequency be set beyond hardware specications since it does not meet the

standard requirements for the peripherals. If you wish to set the frequency beyond the standard

specications, please do so according to your hardware specications including the CPU, graphics

card, memory, hard drive, etc.

Installing the CPU

Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load plate

automatically during the process of re-engaging the lever after you insert the CPU.

Notch

Alignment KeyAlignment Key Notch

LGA1150 CPULGA1150 CPU Socket

Pin One Corner of the CPU Socket Triangle Pin One Marking on the CPU

- 11 -

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specication. Use this port for USB devices such as a USB

keyboard/mouse, USB printer, USB ash drive and etc.

PS/2 Keyboard/Mouse Port

Use this port to connect a PS/2 mouse or keyboard.

Antenna Connector

Use this connector to connect an antenna.

DualChannelMemoryConguration

This motherboard provides two DDR3 memory sockets and supports Dual Channel Technology. After the memory

is installed, the BIOS will automatically detect the specications and capacity of the memory. Enabling Dual

Channel memory mode will double the original memory bandwidth.

The two DDR3 memory sockets are divided into two channels and each channel has one memory socket as

following:

Channel A: DDR3_1

Channel B: DDR3_2

1-5 Installing an Expansion Card

Read the following guidelines before you begin to install an expansion card:

•Make sure the motherboard supports the expansion card. Carefully read the manual that came

with your expansion card.

•Always turn off the computer and unplug the power cord from the power outlet before installing an

expansion card to prevent hardware damage.

1-6 Back Panel Connectors

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.

1. Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.

2. When enabling Dual Channel mode with two memory modules, it is recommended that memory of

the same capacity, brand, speed, and chips be used for optimum performance.

1-4 Installing the Memory

Read the following guidelines before you begin to install the memory:

•Make sure that the motherboard supports the memory. It is recommended that memory of the

same capacity, brand, speed, and chips be used.

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

memory to prevent hardware damage.

•Memory modules have a foolproof design. A memory module can be installed in only one direction.

If you are unable to insert the memory, switch the direction.

Tighten the antenna cables to the antenna connectors and then move the antenna to a place

where the signal is good.

•When removing the cable connected to a back panel connector, rst remove the cable from your

device and then remove it from the motherboard.

•When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent

an electrical short inside the cable connector.

- 12 -

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following

describes the states of the LAN port LEDs.

After installing the HDMI device, make sure to set the default sound playback device to HDMI.

USB 3.0/2.0 Port

The USB 3.0 port supports the USB 3.0 specication and is compatible to the USB 2.0/1.1 specication.

Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB ash drive and etc.

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specication. You can connect a USB DAC to this port or use this

port for USB devices such as a USB keyboard/mouse, USB printer, USB ash drive and etc.

Center/Subwoofer Speaker Out (Orange)

Use this audio jack to connect center/subwoofer speakers in a 5.1/7.1-channel audio conguration.

Rear Speaker Out (Black)

This jack can be used to connect rear speakers in a 4/5.1/7.1-channel audio conguration.

Optical S/PDIF Out Connector

This connector provides digital audio out to an external audio system that supports digital optical audio.

Before using this feature, ensure that your audio system provides an optical digital audio in connector.

Line In (Blue)

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out (Green)

The line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to

connect front speakers in a 4/5.1/7.1-channel audio conguration.

Mic In (Pink)

The Mic in jack. Microphones must be connected to this jack.

DVI-I Port

The DVI-I port conforms to the DVI-I specication and supports a maximum resolution of 1920x1200 (the

actual resolutions supported depend on the monitor being used). Connect a monitor that supports DVI-I

connection to this port.

HDMI Port

The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD

Master Audio formats. It also supports up to 192KHz/24bit 8-channel LPCM audio

output. You can use this port to connect your HDMI-supported monitor. The maximum supported resolution

is 4096x2160, but the actual resolutions supported are dependent on the monitor being used.

The audio jacks can be recongured to perform different functions via the audio software (supported

functions may vary based on hardware specication). If you install a Side Speaker, you need to

retask other audio jack to be Side Speaker out. Only microphones still MUST be connected to the

default Mic in jack.

Activity LED

Connection/

Speed LED

LAN Port

Activity LED:Connection/Speed LED:

State Description

Orange 1 Gbps data rate

Green 100 Mbps data rate

Off 10 Mbps data rate

State Description

Blinking Data transmission or receiving is occurring

On No data transmission or receiving is occurring

- 13 -

1-7 Internal Connectors

1) ATX_12V

2) ATX

3) CPU_FAN

4) SYS_FAN

5) BAT

6) SATA3 0/1/2

7) SATA2

8) F_PANEL

9) F_AUDIO

10) SPDIF_O

11) F_USB30

12) F_USB

13) COM

14) CLR_CMOS

15) CI

813141 34

9 61015

Read the following guidelines before connecting external devices:

•First make sure your devices are compliant with the connectors you wish to connect.

•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

•After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

- 14 -

1/2) ATX_12V/ATX (2x2 12V Power Connector and 2x12 Main Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components

on the motherboard. Before connecting the power connector, rst make sure the power supply is turned

off and all devices are properly installed. The power connector possesses a foolproof design. Connect the

power supply cable to the power connector in the correct orientation.

The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,

the computer will not start.

3/4) CPU_FAN/SYS_FAN (Fan Headers)

All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.

When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is

the ground wire). The speed control function requires the use of a fan with fan speed control design. For

optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

ATX_12V:

Pin No. Denition

1 GND

2 GND

3 +12V

4 +12V

ATX_12V

DEBUG

PORT

G.QBOFM

131

2412

ATX

ATX:

Pin No. Denition Pin No. Denition

1 3.3V 13 3.3V

2 3.3V 14 -12V

3 GND 15 GND

4 +5V 16 PS_ON (soft On/Off)

5 GND 17 GND

6 +5V 18 GND

7 GND 19 GND

8 Power Good 20 NC

9 5VSB (stand by +5V) 21 +5V

10 +12V 22 +5V

11 +12V (Only for 2x12-pin

ATX)

23 +5V (Only for 2x12-pin ATX)

12 3.3V (Only for 2x12-pin

ATX)

24 GND (Only for 2x12-pin ATX)

CPU_FAN: SYS_FAN:

Pin No. Denition

1 GND

2 +12V

3 Sense

4 Speed Control

Pin No. Denition

1 GND

2+12V/Speed Control

3 Sense

4 VCC

•Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating

may result in damage to the CPU or the system may hang.

•These fan headers are not conguration jumper blocks. Do not place a jumper cap on the headers.

SYS_FANCPU_FAN

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

1 1

- 15 -

6) SATA3 0/1/2 (SATA 6Gb/s Connectors)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA

1.5Gb/s standard. Each SATA connector supports a single SATA device.

7) SATA2 (SATA 3Gb/s Connector)

The SATA connector conforms to SATA 3Gb/s standard and are compatible with SATA 1.5Gb/s standard.

Each SATA connector supports a single SATA device.

Pin No. Denition

1 GND

2 TXP

3 TXN

4 GND

5 RXN

6 RXP

7 GND

Pin No. Denition

1 GND

2 TXP

3 TXN

4 GND

5 RXN

6 RXP

7 GND

5) BAT (Battery)

The battery provides power to keep the values (such as BIOS congurations, date, and time information)

in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low

level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:

1. Turn off your computer and unplug the power cord.

2. Gently remove the battery from the battery holder and wait for one minute. (Or use a metal

object like a screwdriver to touch the positive and negative terminals of the battery holder,

making them short for 5 seconds.)

3. Replace the battery.

4. Plug in the power cord and restart your computer.

•Always turn off your computer and unplug the power cord before replacing the battery.

•Replace the battery with an equivalent one. Danger of explosion if the battery is replaced with an incorrect model.

•Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain

about the battery model.

•When installing the battery, note the orientation of the positive side (+) and the negative side (-) of the battery

(the positive side should face up).

•Used batteries must be handled in accordance with local environmental regulations.

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

SATA2

SATA3

To enable hot-plugging for the SATA ports, refer to Chapter 2, "BIOS Setup," "Peripherals\SATA

Conguration," for more information.

- 16 -

8) F_PANEL (Front Panel Header)

Connect the power switch, reset switch, and system status indicator on the chassis to this header according

to the pin assignments below. Note the positive and negative pins before connecting the cables.

•PW (Power Switch, Red):

Connects to the power switch on the chassis front panel. You may congure

the way to turn off your system using the power switch (refer to Chapter 2,

"BIOS Setup," "Power Management," for more information).

•HD (Hard Drive Activity LED, Blue):

Connects to the hard drive activity LED on the chassis front panel. The LED

is on when the hard drive is reading or writing data.

•RES (Reset Switch, Green):

Connects to the reset switch on the chassis front panel. Press the reset switch

to restart the computer if the computer freezes and fails to perform a normal

restart.

•NC (Purple): No connection.

•PLED (Power LED, Yellow):

System Status LED

S0 On

S3/S4/S5 Off

Connects to the power status indicator on the chassis

front panel. The LED is on when the system is

operating. The LED is off when the system is in S3/

S4 sleep state or powered off (S5).

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch,

power LED, hard drive activity LED and etc. When connecting your chassis front panel module to this header,

make sure the wire assignments and the pin assignments are matched correctly.

9) F_AUDIO (Front Panel Audio Header)

The front panel audio header supports Intel High Denition audio (HD) and AC'97 audio. You may connect

your chassis front panel audio module to this header. Make sure the wire assignments of the module

connector match the pin assignments of the motherboard header. Incorrect connection between the module

connector and the motherboard header will make the device unable to work or even damage it.

For HD Front Panel Audio: For AC'97 Front Panel Audio:

Pin No. Denition

1 MIC2_L

2 GND

3 MIC2_R

4 -ACZ_DET

5 LINE2_R

6 Sense

7 FAUDIO_JD

8 No Pin

9 LINE2_L

10 Sense

Pin No. Denition

1 MIC

2 GND

3 MIC Power

4 NC

5 Line Out (R)

6 NC

7 NC

8 No Pin

9 Line Out (L)

10 NC

•The front panel audio header supports HD audio by default.

•Audio signals will be present on both of the front and back panel audio connections simultaneously.

•Some chassis provide a front panel audio module that has separated connectors on each wire instead of a

single plug. For information about connecting the front panel audio module that has different wire assignments,

please contact the chassis manufacturer.

PLED-

PW-

PLED+

PW+

HD-

RES+

HD+

RES-

Power Switch

Hard Drive

Activity LED

Reset Switch

Power LED

- 17 -

12) F_USB (USB 2.0/1.1 Header)

The header conforms to USB 2.0/1.1 specication. Each USB header can provide two USB ports via an

optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

Pin No. Denition Pin No. Denition

1 Power (5V) 6 USB DY+

2 Power (5V) 7 GND

3 USB DX- 8 GND

4 USB DY- 9 No Pin

5 USB DX+ 10 NC

Pin No. Denition Pin No. Denition

1 NDCD- 6 NDSR-

2 NSIN 7 NRTS-

3 NSOUT 8 NCTS-

4 NDTR- 9 NRI-

5 GND 10 No Pin

•Do not plug the IEEE 1394 bracket (2x5-pin) cable into the USB header.

•Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord from the power

outlet to prevent damage to the USB bracket.

10) SPDIF_O (S/PDIF Out Header)

This header supports digital S/PDIF Out and connects a S/PDIF digital audio cable (provided by expansion

cards) for digital audio output from your motherboard to certain expansion cards like graphics cards and

sound cards. For example, some graphics cards may require you to use a S/PDIF digital audio cable for

digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display

to the graphics card and have digital audio output from the HDMI display at the same time. For information

about connecting the S/PDIF digital audio cable, carefully read the manual for your expansion card.

Pin No. Denition

1 SPDIFO

2 GND

11) F_USB30 (USB 3.0/2.0 Header)

The header conforms to USB 3.0/2.0 specication and can provide two USB ports. For purchasing the

optional 3.5" front panel that provides two USB 3.0/2.0 ports, please contact the local dealer.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3 4 5

 S3 BSSS U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

20 1

Pin No. Denition Pin No. Denition Pin No. Denition

1VBUS 8D1- 15 SSTX2-

2SSRX1- 9D1+ 16 GND

3SSRX1+ 10 NC 17 SSRX2+

4GND 11 D2+ 18 SSRX2-

5SSTX1- 12 D2- 19 VBUS

6SSTX1+ 13 GND 20 No Pin

7GND 14 SSTX2+

10 9

13) COM (Serial Port Header)

The COM header can provide one serial port via an optional COM port cable. For purchasing the optional

COM port cable, please contact the local dealer.

- 18 -

14) CLR_CMOS (Clear CMOS Jumper)

Use this jumper to clear the BIOS conguration and reset the CMOS values to factory defaults. To clear

the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.

•Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values.

•After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or manually

congure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS congurations).

Open: Normal

Short: Clear CMOS Values

15) CI (Chassis Intrusion Header)

This motherboard provides a chassis detection feature that detects if the chassis cover has been removed.

This function requires a chassis with chassis intrusion detection design.

Pin No. Denition

1 Signal

2 GND

Chapter 2 BIOS Setup

BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the

motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup,

saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows

the user to modify basic system conguration settings or to activate certain system features.

When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to

keep the conguration values in the CMOS.

To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on.

To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility.

•Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.

•@BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the Internet

and updates the BIOS.

•Because BIOS ashing is potentially risky, if you do not encounter problems using the current version of BIOS,

it is recommended that you not ash the BIOS. To ash the BIOS, do it with caution. Inadequate BIOS ashing

may result in system malfunction.

•It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other

unexpected results. Inadequately altering the settings may result in system's failure to boot. If this occurs, try to

clear the CMOS values and reset the board to default values. (Refer to the "Load Optimized Defaults" section in

this chapter or introductions of the battery/clear CMOS jumper in Chapter 1 for how to clear the CMOS values.)

- 19 -

2-1 Startup Screen

The following startup Logo screen will appear when the computer boots.

(Sample BIOS Version: F1a)

Whether the system will work stably with the overclock/overvoltage settings you made is dependent on your overall

system congurations. Incorrectly doing overclock/overvoltage may result in damage to CPU, chipset, or memory

and reduce the useful life of these components. This page is for advanced users only and we recommend you not to

alter the default settings to prevent system instability or other unexpected results. (Inadequately altering the settings

may result in system's failure to boot. If this occurs, clear the CMOS values and reset the board to default values.)

This section provides information on the BIOS version, CPU base clock, CPU frequency, memory frequency,

total memory size, CPU temperature, Vcore, and memory voltage.

Function Keys

•When the system is not stable as usual, select the Load Optimized Defaults item to set your system to its defaults.

•The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.

On the main menu of the BIOS Setup program, press arrow keys to move among the items and press <Enter>

to accept or enter a sub-menu. Or you can use your mouse to select the item you want.

2-2 M.I.T.

- 20 -

`M.I.T. Current Status

This screen provides information on CPU/memory frequencies/parameters.

`Advanced Frequency Settings

&Processor Graphics Clock

Allows you to set the onboard graphics clock. The adjustable range is from 400 MHz to 4000 MHz. (Default:

Auto)

&CPU Upgrade (Note)

Allows you to set the CPU frequency. Options may vary depending on the CPU being used. (Default: Auto)

&CPU Clock Ratio

Allows you to alter the clock ratio for the installed CPU. The adjustable range is dependent on the CPU

being installed.

&CPU Frequency

Displays the current operating CPU frequency.

`Advanced CPU Core Settings

&CPU Clock Ratio, CPU Frequency

The settings above are synchronous to those under the same items on the Advanced Frequency Settings

menu.

&K OC (Note)

Allows for increased performance by using certain CPUs. (Default: Auto)

&CPU PLL Selection

Allows you to set the CPU PLL. Auto lets the BIOS automatically congure this setting. (Default: Auto)

&Filter PLL Level

Allows you to set the Filter PLL. Auto lets the BIOS automatically congure this setting. (Default: Auto)

&Uncore Ratio

Allows you to set the CPU Uncore ratio. The adjustable range is dependent on the CPU being used.

&Uncore Frequency

Displays the current CPU Uncore frequency.

&Intel(R) Turbo Boost Technology (Note)

Allows you to determine whether to enable the Intel CPU Turbo Boost technology. Auto lets the BIOS

automatically congure this setting. (Default: Auto)

&Turbo Ratio (1-Core Active~4-Core Active) (Note)

Allows you to set the CPU Turbo ratios for different number of active cores. Auto sets the CPU Turbo ratios

according to the CPU specications. (Default: Auto)

&Turbo Power Limit (Watts)

Allows you to set a power limit for CPU Turbo mode. When the CPU power consumption exceeds the

specied power limit, the CPU will automatically reduce the core frequency in order to reduce the power.

Auto sets the power limit according to the CPU specications. (Default: Auto)

&Core Current Limit (Amps)

Allows you to set a current limit for CPU Turbo mode. When the CPU current exceeds the specied current

limit, the CPU will automatically reduce the core frequency in order to reduce the current. Auto sets the

power limit according to the CPU specications. (Default: Auto)

&No. of CPU Cores Enabled (Note)

Allows you to select the number of CPU cores to enable in an Intel® multi-core CPU (the number of CPU

cores may vary by CPU). Auto lets the BIOS automatically congure this setting. (Default: Auto)

(Note) This item is present only when you install a CPU that supports this feature. For more information about

Intel® CPUs' unique features, please visit Intel's website.

La pagina sta caricando ...

Gigabyte GA-B85N Phoenix-WIFI Manuale del proprietario

Marca: Gigabyte

Modello: GA-B85N Phoenix-WIFI

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Gigabyte GA-B85N Phoenix-WIFI Owner's manual

Gigabyte GA-B85N Phoenix-WIFI Manuale del proprietario

Gigabyte GA-B85N Phoenix-WIFI Manuale del proprietario

in altre lingue

Documenti correlati