Zenoah Pole Saw PSZ2600 Manuale utente

Zenoah
Marca
Zenoah
Modello
Pole Saw PSZ2600
Tipo
Manuale utente

Questo manuale è adatto anche per

PSZ2600
GB
GB
F
D
I
E
F
D
I
E
848A5393A1 (701)
OPERATOR’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE D’ISTRUZIONI
MANUAL DE INSTRUCCIONES
POLE SAW
SCIE POLAIRE
LANGBAUMSCHERE
SEGA A PALO
SIERRA DE MANGO
English
Français Deutsch
Italiano
Español
This chain saw is designed especially for tree service by a
trained operator. For safe operation, you must read and
understand this owner's manual completely before operating
the chain saw.
Note: Illustrations and specifications in this manual may vary
according to requirements of individual countries and are
subject to change without notice by the manufacturer.
Cette tronçonneuse est spécialement conçue pour l'entretien
des arbres par un utilisateur formé. Pour une utilisation sûre,
ce mode d'emploi doit être lu et compris entièrement avant
d'utiliser la tronçonneuse.
Remarque: les illustrations et caractéristiques techniques de
ce mode d'emploi peuvent varier en fonctions des exigences
des différents pays et sont sujettes à changements dans
préavis de la part du constructeur.
English
Français
Diese Kettensäge wurde speziell für Baumarbeiten konzipiert
und darf nur von einem ausgebildeten Arbeiter bedient
werden. Um Betriebssicherheit zu gewährleisten muß diese
Bedienungsanleitung vollständig durchgelesen und
verstanden werden, bevor die Kettensäge in Betrieb
genommen wird.
Hinweis: Illustrationen und Spezifikationen in dieser Anleitung
können gemäß den Anforderungen der einzelnen Länder
variieren und können ohne Ankündigung durch den Hersteller
geändert werden.
Questa sega elettrica è stata progettata specialmente per
essere adoperata per gli alberi da parte di un operatore
addestrato. Per un uso sicuro della sega elettrica bisogna
leggere e capire questo manuale d'istruzioni prima di utilizzare
l'apparecchio.
Nota: le illustrazioni e le specificazioni nel manuale potrebbero
variare a seconda delle direttive dei singoli paesi e sono
inoltre soggette a cambiamento senza preavviso da parte del
produttore.
Esta sierra eléctrica ha sido diseñada sólo para cortar árboles
y ser usada por un operador entrenado. Para asegurar un
funcionamiento seguro, debe leer y comprender este manual
de instrucciones en su totalidad antes de utilizar la sierra.
Nota: Las ilustraciones y especificaciones pueden variar
dependiendo de los requerimientos de los distintos países y
están sujetos a cambios sin previo aviso del fabricante.
Español
Deutsch
Italiano
EXPLANATION OF SYMBOLS AND SAFETY WARNINGS
EXPLICATION DES SYMBOLES ET REGLES DE SECURITE
ERLÄUTERUNG DER SYMBOLE-UND SICHERHEITSHINWEISE
SPIEGAZIONE SIMBOLI E AVVERTENZE DI SICUREZZA
EXPLICACION SIMBOLOS Y ADVERTENCIAS DE SEGURIDAD
- Read owner's manual before operating this machine.
- Lire le mode d’emploi avant d'utiliser cette machine.
- Bedienungsanleitung vor der Inbetriebnahme lesen.
- Leggere il manuale d’istruzioni prima di utilizzare questa macchina.
- Antes de utilizar esta máquina, leer el manual de instrucciones.
- Wear head, eye and ear protection.
- Porter casque, visière et protège-oreilles.
- Immer Helm, Schutzbrille und Geräuschschutz tragen.
- Indossare casco, occhiali e cuffie di protezione.
- Llevar casco, gafas y auriculares de protección.
- Use the chain saw with two hands
- Utiliser la tronçonneuse en se servant des deux mains
- Die Kettensäge nur beidhändig bedienen
- Usare la motosega con due mani
- Sujete siempre la motosierra con ambas manos
- Warning! Kickback it's danger.
- Portez une attention particulière aux phénomènes de rebond.
- Achtung! Vorsicht Rückschlaggefahr.
- Fare particolare attenzione al fenomeno del contraccolpo. Può essere pericoloso.
- Atencion! Advertencia sobre el peligro de sacudida.
- Read, understand and follow all warnings.
- Lisez, cherchez à comprendre et suivez toutes les instructions.
- Die in der Bedienungsanleitung und an der Maschine angegebenen Warnungstexte.
- Leggere con attenzione e seguire tutte le avvertenze.
- Lea, comprenda y siga todas las advertencias.
GB
F
D
I
E
ATENCION!!!
RIESGO DE DAÑO AUDITIVO
EN NORMALES CONDICIONES DE UTILIZACIÓN, ESTA MAQUINA PUEDE
TOLERAR, PARA EL OPERADOR ENCARGADO, UN NIVEL DE EXPOSICÍON
DIARIO A RUIDO EQUIVALENTE O SUPERIOR A
86 dB(A)
WARNING!!!
RISK OF DAMAGING HEARING
IN NORMAL CONDITIONS OF USE, THIS MACHINE
MAY INVOLVE A DAILY LEVEL OF PERSONAL EXPOSURE TO NOISE
FOR THE OPERATOR EQUAL TO OR GREATER THAN
86 dB(A)
ATTENTION!!!
DANGER D'ATTEINTE A L'OUIE
L'OPERATEUR UTILISANT NORMALEMENT CETTE MACHINE
PEUTS S'EXPOSER QUOTIDIENNEMENT
A UN BRUIT EGAL OU DEPASSANT
86 dB(A)
ACHTUNG!!!
HÖRSCHADEN - RISIKO
UNTER NORMALEN ANWENDUNGSBEDIGUNGEN
KANN DIESES GERÄT DIE BEDIENUNGSPERSON
EINEM TÄGLICHEN GERÄUSCHPEGEL VON
86 dB(A)
ODER MEHR AUSSETZEN
ATTENZIONE!!!
RISCHIO DI DANNO UDITIVO
NELLE NORMALI CONDIZIONI DI UTILIZZO, QUESTA MACCHINA PUÒ
COMPORTARE PER L'OPERATORE ADDETTO, UN LIVELLO DI ESPOSIZIONE
PERSONALE E GIORNALIERO A RUMORE PARI O SUPERIORE A
86 dB(A)
MODEL SOUND LEVEL VIBRATION LEVEL
MODELE NIVEAU SONORE NIVEAU DE VIBRATION
MODELLE KLANGPEGEL VIBRATIONSPEGEL
MODELLO LIVELLO DEL SUONO LIVELLO DI VIBRAZIONE
MODELO NIVEL DE SONIDO NIVEL DE VIBRACION
ISO 11680 ISO 11680
LwA
mesured guaranteed
25.4cm
3
94dB(A) 109dB(A) 114dB(A) 2.5m/s
2
8.3m/s
2
LpA idling racing
APPROVAL NUMBER OF CE EXHAUST
EMISSION REGULATION (2002/88/EC)
e13*97/68SH2G3*2002/88*0094*02
NUMERO D’APPROBATION DES
REGLEMENTATIONS SUR LES EMISSIONS
DES GAZ D’ECHAPPEMENT
DE LA CE (2002/88/EC)
e13*97/68SH2G3*2002/88*0094*02
ZULASSUNGSNUMMER FÜR
CE-ABGASBESTIMMUNGEN (2002/88/EC)
e13*97/68SH2G3*2002/88*0094*02
APPROVAZIONE REGOLAMENTO CEE
SULLE EMISSIONI DI GAS (2002/88/EC)
e13*97/68SH2G3*2002/88*0094*02
NÚMERO DE APROBACIÓN DEL
REGLAMENTO CE SOBRE EMISIONES DE
GASES DE ESCAPE (2002/88/EC)
e13*97/68SH2G3*2002/88*0094*02
English Français
SAFETY FIRST
Instructions contained in warnings
within this manual marked with a
symbol concern critical points which
must be taken into consideration to
prevent possible serious bodily injury,
and for this reason you are requested
to read all such instructions carefully
and follow them without fail.
■ WARNINGS IN THE MANUAL
This mark indicates instructions which
must be followed in order to prevent
accidents which could lead to serious
bodily injury or death.
This mark indicates instructions which
must be followed, or it leads to mechanical
failure, breakdown, or damage.
This mark indicates hints or directions
useful in the use of the product.
NOTE
IMPORTANT
WARNING
SECURITE
Les instructions contenues dans les
mises en garde de ce mode d’emploi
portant le symbole concernent les
points critiques qui doivent être pris en
considération pour éviter les blessures
corporelles graves, c’est pourquoi ces
précautions doivent être
rigoureusement suivies.
■ DIFFERENTS TYPES
D’AVERTISSEMENT DE CE MODE
D’EMPLOI
Les instructions repérées par ce symbole
doivent être rigoureusement suivies afin
d’éviter tout accident pouvant entraîner
des blessures corporelles graves ou la
mort.
Les instructions repérées par ce symbole
doivent être suivies afin d’éviter tout
incident mécanique, panne ou
endommagement de la débroussailleuse.
Remarques utilisées dans des instructions
ou conseils supplémentaires pour
l’utilisation de cette débroussailleuse.
REMARQUE
IMPORTANT
AVERTISSEMENT
Contents Tables des matieres
8
1. Parts location..................................10
2. Specifications .................................12
3. Warning labels on the machine......14
4. Symbols on the machine................14
5. For safe operation ..........................16
6. Set up.............................................32
7. Fuel and chain oil ...........................36
8. Operation........................................42
9. Maintenance...................................48
10. Storage...........................................60
11. Troubleshooting guide....................64
1. Emplacement des composants ......10
2. Caracteristiques .............................12
3.
Etiquettes d’avertissement placées sur la
machine
............................................14
4. Symboles utilises sur la machine ...14
5. Consignes de securite....................16
6. Assemblage....................................32
7. Carburant et huile de chaîne..........36
8. Fonctionnement..............................42
9. Entretien.........................................48
10. Rangement.....................................60
11.
Guide de localisation des pannes
........64
EspañolDeutsch Italiano
SICHERHEIT HAT VORRANG
Die Hinweise in den Warnungen dieser
Anleitung bzw. auf den mit einem -
Symbol gekennzeichneten
Warnplaketten sind von größter
Bedeutung für die Betriebssicherheit.
Deshalb sollten Sie diese Warnungen
sorgfältig durchlesen und strikt
beachten, um das Risiko von schweren
Verletzungen zu vermeiden.
■ WARNHINWEISE IN DER
ANLEITUNG
Dieses Symbol bedeutet, daß diese
Instruktionen befolgt werden müssen,
damit Unfälle mit folgenschweren
Verletzungen, die u.a. zum Tode führen
können, vermieden werden.
Dieses Symbol bedeutet, daß diese
Instruktionen befolgt werden müssen oder
es kommt zu mechanischen Defekten,
Versagen des Gerätes oder Schäden.
Dieses Symbol zeigt Tips oder Ratschläge
für den Gerätebetrieb an.
HINWEIS
WICHTIG
WARNUNG
LA SICUREZZA INNANZI TUTTO
Le istruzioni contenute nelle sezioni di
avvertimento precedute dal simbolo
riguardano dei punti critici che
devono essere osservate per prevenire
potenziali lesioni personali gravi. Per
questo motivo, dovete leggere tutte
queste istruzioni attentamente ed
osservarne il contenuto in ogni
momento.
■ SEGNALAZIONI USATE NEL
MANUALE
Questo marchio rappresenta delle
istruzioni che devono essere osservate
per prevenire eventuali incidenti che
possono causare lesioni gravi o addirittura
mortali.
Questo marchio indica delle istruzioni che
devono essere seguite per evitare
malfunzionamenti meccanici, guasti o
danni.
Questo marchio indica dei suggerimenti o
indicazioni utili per l’utilizzo del prodotto.
NOTA
IMPORTANTE
AVVERTIMENTO
LA SEGURIDAD PRIMERO
Las instrucciones que aparecen en
este manual bajo las advertencias
marcadas con el símbolo hacen
referencia a puntos críticos que deben
tomarse en consideración para evitar
posibles lesiones físicas; por esta
razón, le solicitamos que lea
detenidamente todas estas
instrucciones y que las siga
estrictamente.
■ ADVERTENCIAS CONTENIDAS EN
EL MANUAL
Bajo este símbolo aparecen instrucciones
que se deben seguir a fin de evitar
accidentes que pueden causar serias
lesiones físicas o la muerte.
Bajo este símbolo aparecen instrucciones
importantes que se deben seguir; ignorar
estas instrucciones puede ocasionar fallos
mecánicos, desperfectos o daños.
Este símbolo hace referencia a consejos o
indicaciones que son de utilidad para el
uso del producto.
NOTA
IMPORTANTE
ADVERTENCIA
Inhalt ContenidoIndice
9
1. Ubicazione delle parti.....................11
2. Specifiche.......................................13
3. Etichetta di avvertimento
sull’apparecchio..............................15
4. Simboli sulla macchina...................15
5. Per un funzionamento sicuro..........17
6. Impostazione..................................33
7.
Olio del carburante e della catena
.......37
8. Funzionamento...............................43
9. Manutenzione.................................49
10. Immagazzinaggio ...........................61
11. Localizzazione dei guasti ...............65
1. Posición de las piezas....................11
2. Especificaciones.............................13
3. Etiqueta de advertencias en la
máquina..........................................15
4.
Símbolos presentes en la máquina
.....15
5. Instrucciones de seguridad ............17
6. Montaje...........................................33
7.
Combustible y aceite de la cadena
......37
8. Uso.................................................43
9. Mantenimiento................................49
10. Almacenamiento.............................61
11. Guía de localización y solución de
problemas.......................................65
1. Position der bauteile.......................11
2. Technische daten...........................13
3. Warnaufkleber auf der Maschine ...15
4. Symbole auf der maschine.............15
5. Sicherer betrieb..............................17
6. Zusammenbau ...............................33
7. Kraftstoff und Kettenöl....................37
8. Betrieb............................................43
9. Wartung..........................................49
10. Lagerung ........................................61
11. Fehlersuche....................................65
English Français
1. Parts location 1. Emplacement des pieces
10
(1) Primer pump
(2) Air cleaner cover
(3) Choke lever
(4) Fuel tank
(5) Starter knob
(6) Spark arrester
(7) Gear case
(8) Chain cover
(9) Saw chain
(10) Guide bar
(11) Grip
(12) Drive shaft housing
(13) Sholder strap hanger
(14) Throttle lever
(15) Ignition switch
(16) Throttle cable
(17) Throttle set button
(1) Pompe d’amorçage
(2) Capot du filtre à air
(3) Levier de starter
(4) Réservoir de carburant
(5) Poignée de démarrage
(6) Pare-étincelles du silencieux
(7) Lame de coupe
(8) Boîtier du renvoi d’angle
(9) Cache de protection
(10) Barre guide
(11) Poignée
(12) Tube de l’arbre d’entraînement
(13) Fixation du harnais
(14) Levier d’accélération
(15) Bouton d’allumage
(16) Câble d’accélérateur
(17) Bouton de blocage de
l’accélérateur
EspañolDeutsch Italiano
1. Anordnung der bauteile 1. Ubicazione dei componenti 1. Situación de las piezas
11
(1) Anlaßeinspritzpumpe
(2) Luftfilterabdeckung
(3) Chokehebel
(4) Kraftstofftank
(5) Startknopf
(6) Funkenfänger
(7) Blatt
(8) Winkelgetriebe
(9) Abfallschutz
(10) Führungsstange
(11) Klemme
(12) Antriebswelle
(13) Schultergurtklammer
(14) Drosselklappenhebel
(15) Zündschalter
(16) Drosselklappenkabel
(17) Drossel-Einstelltaste
(1) Pompa del cicchetto
(2) Coperchio del filtro dell’aria
(3) Leva del dispositivo di
avviamento a freddo
(4) Serbatoio del carburante
(5)
Manopola del motorino di avviamento
(6) Parascintille
(7) Lama
(8) Scatola degli ingranaggi
(9) Protezione contro i detriti
(10) Barra guida
(11) Impugnatura
(12) Albero motore
(13) Occhiello per tracolla
(14) Leva del gas
(15) Interruttore di accensione
(16) Cavo del gas
(17) Tasto di impostazione della
valvola a farfalla
(1) Cebador
(2) Cubierta del filtro de aire
(3) Palanca del estrangulador
(4) Tanque de combustible
(5) Arrancador
(6) Parachispas
(7) Cuchilla
(8) Caja de engranajes
(9) Protector contra desechos
(10) Barra de guía
(11) Agarre
(12) Eje de accionamiento
(13) Colgador de correa para hombro
(14) Palanca del acelerador
(15) Interruptor de encendido
(16) Cable del acelerador
(17) Botón del grupo acelerador
English
2. Specifications
12
Français
2. Fiche technique
■ PSZ2600
Dimensions totales (L x L x H)······················ 2085 x 250 x 310 mm
Poids à vide ··········································································5,40 kg
Moteur Type······················· 2 temps à essence refroidi par air
Modèle················································ Zenoah GZ25N
Cylindrée ·······················································25,4 cm3
Puissance maximale······· 1,2 CV (0,9kW) à 7500 t/mn
Vitesse de ralenti ······························ 3000 ± 200 t/mn
Carburant··················· Mélange (essence 50 : huile 1)
(Lors de l’utilisation de la véritable huile ZENOAH)
Carburateur······························· Walbro à diaphragme
Bougie d’allumage ································· NGK CMR7A
Période de durabilité ··································300 heures
Capacité du réservoir d’essence············································0.65
Transmission····················
Embrayage centrifuge, arbre d’entraînement rigide
Rapport de réduction·································································1,06
■ PSZ2600
Overall size (L x W x H) ································· 2085 x 250 x 310mm
Dry weight············································································· 5.40kg
Engine Type································ Air-cooled 2-stroke gasoline
Model·················································· Zenoah GZ25N
Displacement·················································· 25.4cm
3
Max. output ·············· 1.2Hp (0.9kW)at 7500min
-1
(rpm)
Idle speed·····································3000±200min
-1
(rpm)
Fuel ································ Mixture (Gasoline 50 : Oil 1)
(when using ZENOAH genuine oil)
Carburetor ····························· Walbro Diaphragm type
Spark plug···············································NGK CMR7A
Durability period ···············································300 hrs
Fuel tank capacity ··································································0.65
Transmission····························· Centrifugal clutch, Rigid driveshaft
Reduction ratio ········································································· 1.06
Cutting head
Guide bar Type ······························ OREGON DOUBLE GUARD
Size······················································· 10(25) in.(cm)
Saw chain Type············································ OREGON 90SG39X
Pich x Gauge ············ 3/8x0.043 (9.53 x 1.07) in.(mm)
Sprocket ······················································································ 7T
Oil pump·······································································Plunger type
Standard Accessories
Shoulder Strap········································································· 1 pc.
Tool Kit····················································································· 1 pc.
Guide bar protector·································································· 1 pc.
Specifications are subject to change without notice.
Tête de découpage
Barre guide Type ···························OREGON DOUBLE GUARD
Taille ·······································10(250) pouces(mm)
Scie à chaîne
Type·········································OREGON 90SG39X
Lancement et jauge
········
3/8x0.043(9.53x1.07) pouces(mm)
Galet·····························································································7T
Pompe à huile···························································Type plongeoir
Accessoires standard
Courroie à épaules ····································································1pc.
Lunettes·····················································································1pc.
Protecteur de Barre Guide·························································1pc.
Ces spécifications peuvent être modifiées sans préavis.
Deutsch
13
2. Technische Daten
Italiano
2. Dati tecnici
Español
2. Especificaciohes
■ PSZ2600
Tamaño global (Long x Anch x Alt)··············· 2085 x 250 x 310 mm
Peso en seco······································································ 5,40 kg.
Motor Tipo ······· Refrigerado por aire / gasolina de 2 tiempos
Modelo ··············································· Zenoah GZ25N
Desplazamiento············································· 25,4 cm
3
Potencia máxima ············ 1,2 Hp (0,9kW) a 7500 rpm
Velocidad de marcha en vacío ········· 3000 ± 200 rpm
Combustible ············· Mezcla (Gasolina 50: Aceite 1)
(al utilizar el aceite auténtico de ZENOAH)
Carburador ····························· Walbro tipo Diafragma
Bujía ······················································ NGK CMR7A
Período de duración··········································300hrs
Capacidad del depósito de combustible ································0,65
Transmisión·························Embrague centrífugo, Eje motor rígido
Relación de reducción·······························································1,06
■ PSZ2600
Abmessungen (L x B x H)····························· 2085 x 250 x 310 mm
Trockengewicht···································································· 5,40 kg
Motor Typ·························· luftgekühlter 2-Takt-Benzinmotor
Modell················································· Zenoah GZ25N
Hubraum························································ 25,4 cm
3
Max. Ausgang·········· 1,2 Hp (0,9 kW) bei 7500 U/Min.
Leerlaufgeschwindigkeit
······················ 3000 ± 200 U/Min.
Kraftstoff··················· Gemisch(Benzin 50, Öl 1 Anteil)
(bei der Verwendung von original ZENOAH-Öl)
Vergaser ····································· Walbro-Diaphragma
Zündkerze·············································· NGK CMR7A
Lebensdauer ·······························300 Betriebsstunden
Kraftstofftank-Kapazität··························································0,65
Getriebe························Fliehkraftkuppelung, robuste Antriebswelle
Reduktionsverhältnis ·································································1,06
■ PSZ2600
Dimensioni (L x P x H) ·································· 2085 x 250 x 310 mm
Peso a vuoto········································································ 5,40 kg
Motore Tipo·······
Motore a benzina a 2 tempi con raffreddamento ad aria
Modello··············································· Zenoah GZ25N
Cilindrata ······················································· 25,4 cm
3
Uscita massima········ 1,2 HP (0,9 kW) a 7500 giri/min.
Velocità alla minima····················· 3000 ± 200 giri/min.
Carburante ······················ Miscela (benzina 50/ olio 1)
(quando si utilizza olio originale ZENOAH)
Carburatore································· Walbro a diaframma
Candela ················································· NGK CMR7A
Periodo di durata··············································300 ore
Capacità del serbatoio ···························································0.65
Trasmissione ··························
Frizione centrifugale, Barra di comando rigida
Riduzione ratio···········································································1,06
Schneidkopf
Führungsstange Typ
····················
OREGON DOUBLE GUARD (Doppelschutz)
Größe··························································250 mm
Sägekette Typ···········································OREGON 90SG39X
Abstand x Breite······························9,53 x 1,07 mm
Zahnrad························································································7T
Ölpumpe···········································································Kolbentyp
Standard-Zubehör
Schulterriemen ······································································1 Stck.
Brille·······················································································1 Stck.
Führungsschienenschutz·······················································1 Stck.
Technischen Daten können ohne Vorankündigung geändert werden.
Testa tagliente
Barra di guida Tipo ····························OREGON DOUBLE GARD
Taglia···········································10(250) in (mm)
Sega a catena Tipo ···········································Oregon 90SG39x
Passo x misurazione
···········
3/8x0,043(9,53x1,07) in(mm)
Rocchetto ·····················································································7T
Pompa dell’olio ························································Tipo a stantuffo
Accessori standart
Nastro metallico di unione di legnami·········································1pz
Icchiali di protezione ···································································1pz
Protettore di barra di guida ·························································1pz
Le specifiche sono soggette a modifiche senza preavviso.
Cabeza cortadora
Barra de la guía
Tipo··························OREGON DOUBLE GUARD
Tamaño ······································12(250) en (mm)
Cadena de la sierra
Tipo·······································OREGON 90SG39X
paso x medida·······3/8x0,043(9,53x1,07) en (mm)
Piñón ····························································································7T
Bomba del aceite·····················································Tipo de émbolo
Accesorios estándares
Correa para el hombro································································1pz
Anteojos······················································································1pz
Protector de Barra Guía······························································1pz
Especificaciones sujetas a cambios sin previo aviso.
English Français
3. Warning labels on the
machine
3. Etiquettes d’avertissement
sur la machine
14
(1) Read owner's manual before
operating this machine.
(2) Wear head, eye and ear protection.
(3) Warning/Attention
(4) The unit has not been designed to
provide protection from electric
shock in the event of contact with
overhead electric lines.
If warning labels peel off or become soiled
and impossible to read, you should
contact the dealer from which you
purchased the product to order new labels
and affix them in the required location(s).
Never remodel your brushcutter.
We won't warrant the machine, if you
use the remodeled brushcutter or you
don't observe the proper usage written
in the manual.
WARNING
IMPORTANT
(1) Lire le mode d’emploi avant
d’utiliser cette machine.
(2) Porter un casque de sécurité, des
lunettes de sécurité et un casque
antibruit.
(3) Avertissement/Attention
(4) L'unité n'a pas été conçue pour
assurer la protection contre une
décharge électrique en cas du
contact avec des lignes électriques
aériennes.
Si les étiquettes d’avertissement se
décollent, deviennent sales ou impossible
à lire, commander de nouvelles étiquettes
auprès du revendeur pour les remplacer.
Ne pas modifier la débroussailleuse.
La garantie sera annulée si la
débroussailleuse a été modifiée ou
utilisée de manière non conforme aux
instructions de ce mode d’emploi.
AVERTISSEMENT
IMPORTANT
4. Symbols on the machine
4. Symboles utilises sur la
machine
For safe operation and maintenance,
symbols are carved in relief on the
machine. According to these indications,
please be careful not to take a mistake.
(a) The port to refuel the "MIX GASOLINE"
Position: FUEL TANK CAP
(b) The direction to close the choke
Position: AIR CLEANER COVER
(c) The direction to open the choke
Position: AIR CLEANER COVER
(d). If you turn the rod by screwdriver
follow the arrow to the "MAX" position,
the chain oil flow more, and if you turn
to the "MIN" position, less.
Position: Bottom of the power unit
Des symboles en relief ont été placés sur
la machine pour assurer la sécurité à
l’usage et faciliter l’entretien. Prendre soin
d’observer les indications suivantes afin
d’éviter les erreurs.
(a) Emplacement de remplissage du
“MELANGE”
Emplacement: BOUCHON DU
RESERVOIR DE CARBURANT
(b) Position fermée du starter
Emplacement: CAPOT DU FILTRE A
AIR
(c) Position ouverte du starter
Emplacement: CAPOT DU FILTRE A
AIR
(d).
Si on fait tourner la tige à l'aide d'un
tournevis, suivre la flèche jusque la position
"MAX" pour faire arriver plus d'huile sur la
chaîne, et faire tourner la tige vers la
position "MIN" pour qu'il en arrive moins.
Emplacement: Partie inférieure de
l'ensemble moteur
EspañolDeutsch Italiano
3. Warnaufkleber auf der
Maschine
3. Etichetta di avvertimento
sull’apparecchio
3. Etiqueta de advertencia en
la máquina
15
(1) Vor dem Betrieb dieser Maschine,
die Bedienungsanleitung lesen.
(2) Kopf-, Augen und Ohrenschutz
tragen.
(3) Warnung/Achtung
(4) Das Gerät wurde nicht hergestellt,
um einen Schutz vor Elekroschocks
im Falle eines Kontaktes mit einer
Überland-Stromleitung zu
gewährleisten.
Wenn Warnplaketten sich lösen oder
schmutzig und nicht mehr lesbar sind,
verständigen Sie Ihren Händler bei dem
Sie das Produkt gekauft haben, um neue
Plaketten zu bestellen und diese an den
erforderlichen Positionen zu befestigen.
Ihren Freischneider niemals
modifizieren.
Die Garantie erlischt, wenn Sie einen
modifizierten Freischneider verwenden
oder Sie nicht den in der
Bedienungsanleitung beschriebenen
Betrieb beachten.
WARNUNG
WICHTIG
(1) Leggete il manuale d’istruzioni
prima di usare questa macchina.
(2) Indossate il casco, gli occhiali di
protezione e le cuffie.
(3) Avvertimento/Attenzione
(4) L’unità non è stata designata a
provvedere alla protezione da shock
elettrico nel caso di contatto con
linee elettriche sovrastanti.
Se un’etichetta di avvertimento si stacca o
si sporca e diventa così illeggibile,
contattate il rivenditore presso il quale
avete acquistato il prodotto per ordinare
delle nuove etichette. Poi fissate le nuove
etichette negli appositi luoghi.
Non modificate mai il decespugliatore.
Se modificate il decespugliatore
oppure non seguite le istruzioni fornite
in questo manuale, la garanzia sarà
nulla.
AVVERTIMENTO
IMPORTANTE
(1) Lea el manual de instrucciones
antes de usar esta máquina.
(2) Use protección para la cabeza, ojos
y oídos.
(3) Advertencia/Atención
(4) La unidad no ha sido diseñada para
proporcionar protección contra
descargas eléctricas en el caso de
contacto con líneas aéreas
eléctricas.
Si las etiquetas de advertencia se
desprenden o se manchan y se vuelven
ilegibles, contacte al distribuidor donde
adquirió el producto y solicite nuevas
etiquetas. Fije las nuevas etiquetas en las
posiciones correspondientes.
Nunca haga ningún tipo de
modificación al desbrozador.
No podemos garantizar la máquina si
usted utiliza el desbrozador
remodelado o si no sigue las
instrucciones de uso contenidas en
este manual.
IMPORTANTE
4. Symbole auf der Maschine 4. Simboli sulla macchina
4. Símbolos presentes en la
máquina
Für einen sicheren Betrieb und eine
sichere Wartung sind Symbole als
Hilfestellung auf die Maschine eingeprägt.
Gehen Sie gemäß diesen Anzeigen
vorsichtig vor und machen Sie keinen
Fehler.
(a) Die Öffnung zum Nachfüllen des
“BENZINGEMISCHS”
Position:
KRAFTSTOFFTANKDECKEL
(b) Die Richtung zum Schließen der
Drossel
Position: LUFTFILTERABDECKUNG
(c) Die Richtung zum Öffnen der Drossel
Position: LUFTFILTERABDECKUNG
(d). Wenn Sie die Welle mit einem
Schraubendreher in Pfeilrichtung in die
Position "MAX" drehen, ist der Ölfluß
stärker und wenn Sie die Position
"MIN" einstellen, ist der Ölfluß
geringer.
Position: Geräteboden
Per un funzionamento e una
manutenzione sicura, i simboli sono stati
incisi in rilievo sull’apparecchio. Seguite
queste indicazioni per evitare eventuali
errori.
(a) Porta per riempire la miscela “MIX
GASOLINE”,
Posizione: COPERCHIO DEL
SERBATOIO DEL CARBURANTE.
(b) Direzione di chiusura dell’aria
Posizione: COPERCHIO DEL FILTRO
DELL’ARIA
(c) Direzione di apertura dell’aria
Posizione: COPERCHIO DEL FILTRO
DELL’ARIA
(d). Se girate l'asta con un cacciavite,
seguite la freccia verso la posizione
"MAX" e l'olio fluirà in quantità
maggiore nella catena; se la girate
verso la posizione "MIN", fluirà in
quantità minore.
Posizione: Fondo dell'unità di potenza
Para el uso y mantenimiento seguro del
producto, los símbolos han sido
estampados en relieve en la máquina.
Siga siempre estas indicaciones, y tenga
cuidado de no cometer un error.
(a) Orificio de llenado de “MEZCLA DE
GASOLINA”
Posición: TAPÓN DEL TANQUE DE
COMBUSTIBLE
(b) Dirección de cierre del estrangulador
Posición: CUBIERTA DEL FILTRO
DE AIRE
(c) Dirección de apertura del
estrangulador
Posición: CUBIERTA DEL FILTRO
DE AIRE
(d).
Si gira la varilla utilizando un
destornillador, siga la dirección indicada
por la flecha a la posición "MAX" para
que el aceite de la cadena fluya más, y a
la posición "MIN" para que fluya menos.
Posición: Fondo de la unidad de
alimentación
English Français
5. For safe operation
16
1. Read this manual carefully until you
completely understand and follow all
safety and operating instructions.
2. Keep this manual handy so that you
may refer to it later whenever any
questions arise. Also note, if you have
any questions which cannot be
answered herein, contact the dealer
from whom you purchased the
product.
3. Always be sure to include this manual
when selling, lending, or otherwise
transferring the ownership of this
product.
4. Never allow children or anyone
unable to fully understand the
directions given in the manual to use
the machine.
■ WORKING CONDITION
1. When using the product, you should
wear proper clothing and protective
equipment.
(1) Helmet
(2) Ear protectors
(3) Protection goggles or face protector
(4) Thick work gloves
(5) Non-slip-sole work boots
2. And you should carry with you.
(1) Attached tools and files
(2) Properly reserved fuel
(3) Spare blade
(4) Things to notify your working area
(rope, warning signs)
(5) Whistle (for collaboration or
emergency)
(6) Hatchet or saw (for removal of
obstacles)
3. Do not wear loose clothing, jewelry,
short trousers, sandals, or go barefoot.
Do not wear anything which might be
caught by a moving part of the unit.
Secure hair so it is above shoulder
length.
■ WORKING CIRCUMSTANCE
1. Never start the engine inside a closed
room or building. Exhaust gases
contain dangerous carbon monoxide.
2. Never use the product:
a. when the ground is slippery or when
you can’t maintain a steady posture.
b. At night, at times of heavy fog, or at
any other times when your field of
vision might be limited and it would
1. Lire ce manuel attentivement jusqu’à
une compréhension totale et suivre
toutes les instructions de sécurité et
d’utilisation.
2. Conserver ce mode d’emploi à portée
de la main pour le consulter au
moindre doute. Si une question reste
sans réponse, contacter le revendeur.
3. Ne pas oublier de donner le manuel
avec la machine en cas de revente ou
de prêt.
4. Ne pas laisser des enfants ou toute
personne incapable de comprendre
les instructions, utiliser cette machine.
■ CONDITIONS DE TRAVAIL
1. Lors de l’utilisation de cette machine, il
est nécessaire de porter des vêtements
appropriés et des équipements de
sécurité.
(1) Casque
(2) Casque antibruit
(3) Lunettes ou masque de protection
(4) Gants de travail épais
(5) Chaussures de sécurité à semelle
antidérapante
2. Les objets suivants doivent être
emportés sur le lieu de travail :
(1) Les outils fournis avec la machine et
des limes
(2) Une réserve de carburant
(3) Une lame de rechange
(4) Matériel pour délimiter la zone de
travail
(5) Un sifflet (pour collaborateur ou en
cas d’urgence)
(6) Une hache ou une scie (pour
enlever les obstacles)
3. Ne pas porter des vêtements lâches, de
short, de bijou, de sandales ou travailler
pieds nus. Ne pas porter quoi que ce
soit pouvant être happé par les pièces
en mouvement de la machine. Porter
les cheveux longs noués au-dessus des
épaules.
■ CONDITIONS DE TRAVAIL
1. Ne jamais mettre la machine en marche
à l’intérieur d’une pièce ou d’un
bâtiment. Les gaz d’échappement
contiennent du monoxide de carbone
dangereux.
2. Ne jamais utiliser la machine dans les
conditions suivantes:
a. Lorsque le sol est glissant ou lorsqu’il
est impossible de se maintenir dans
5. Consignes de securite
EspañolDeutsch Italiano
17
1. Lesen Sie sich diese Anleitung
sorgfältig durch, bis Sie alle
Sicherheits- und Bedienungshinweise
verstehen und befolgen.
2. Diese Anleitung greifbereit haben, um
sie im Zweifelsfall schnell zur Hand zu
haben. Bei Fragen zum Gerät, die
nicht in dieser Anleitung behandelt
werden, bitte an den Händler wenden,
der Ihnen das Produkt verkauft hat.
3. Bei Verkauf, Verleih oder Weitergabe
stets diese Anleitung zusammen mit
dem Gerät übergeben.
4. Niemals Kinder oder Personen, die
die Anweisungen in dieser Anleitung
nicht vollständig verstehen, die
Maschine betreiben lassen.
■ ARBEITSBEDINGUNG
1. Wenn das Produkt benutzt wird, sollten
Sie stets richtige Kleidung und
Schutzausrüstung tragen.
(1) Helm
(2) Ohrenschutz
(3) Schutzbrille oder Schutzmaske
(4) Dicke Schutzhandschuhe
(5) Rutschfeste Arbeitsschuhe
2. Und Sie sollten folgende Dinge bei sich
tragen.
(1) Mitgelieferte Werkzeuge und Feilen
(2) Reservekraftstoff
(3) Ersatzschneidblatt
(4) Gegenstände, die Ihren
Arbeitsbereich kennzeichnen (Seil,
Warnzeichen)
(5) Pfeife (für Zusammenarbeit oder
Notfall)
(6) Beil oder Säge (zum Entfernen von
Hindernissen)
3. Keine lockere Kleidung, Schmuck,
kurze Hosen oder Sandalen tragen und
nicht barfuß gehen. Nichts tragen, daß
von den beweglichen Teilen des
Gerätes erfaßt werden kann. Haare
über Schulterhöhe zusammenbinden.
■ ARBEITSUMSTAND
1. Den Motor niemals in geschlossenen
Räumen oder Gebäuden starten.
Abgase enthalten gefährliches
Kohlenmonoxid.
2. Niemals das Produkt benutzen:
a. wenn der Untergrund glitschig ist
oder ein stabiler Stand beeinträchtigt
ist.
b. Nachts, bei dichtem Nebel oder
1. Leggete questo manuale
attentamente per capire
completamente ed osservare tutte le
norme di sicurezza ed istruzioni per
l’uso.
2. Tenete questo manuale in un luogo
accessibile per poter fare riferimento
all stesso in un momento successivo,
in caso di dubbi. Inoltre, se avete
delle domande alle quali non trovate
la risposta nel manuale, rivolgetevi al
vostro rivenditore da cui avete
acquistato questo prodotto.
3. Assicuratevi di allegare questo
manuale se vendete o prestate l’unità
oppure se la stessa cambia
proprietario in altri modi.
4. Non lasciate mai che bambini o
persone non consapevoli delle
istruzioni fornite nel manuale
d’istruzioni utilizzino l’apparecchio.
■ CONDIZIONI LAVORATIVE
1. Quando usate il prodotto, dovete
indossare i vestiti e le protezioni
appropriate.
(1) Casco
(2) Cuffie di protezione
(3) Occhiali di protezione o visiera
(4) Spessi guanti di lavoro
(5) Scarponi di lavoro con la suola
antiscivolo
2. Inoltre, portate i seguenti oggetti con
voi:
(1) Gli utensili e le lime in dotazione
(2) Il carburante custodito in modo
appropriato
(3) Una lama di riserva
(4) Oggetti per delimitare l’area di
lavoro (una corda, delle insegne di
avvertimento)
(5) Un fischietto (per collaborazione o
per situazioni di emergenza)
(6) Accetta o sega (per rimuovere degli
ostacoli)
3. Non indossate dei vestiti lenti, gioielli,
pantaloncini, sandali, né camminate
scalzo. Non indossate nessun oggetto
che possa rimanere inceppato nelle
parti mobili dell’unità. Legate i capelli in
modo tale che sia al di sopra
dell’altezza delle spalle.
■ CIRCOSTANZE LAVORATIVE
1. Non accendete mai il motore all’interno
di una stanza chiusa o in un edificio. I
gasi di scarico contengono il monossido
di carbonio che è molto pericoloso.
2. Non usate mai il prodotto nelle seguenti
situazioni:
a. Quando il terreno è scivoloso o
quando non potete mantenere una
posizione stabile.
1. Lea detenidamente este manual
hasta comprender cabalmente todas
las instrucciones de seguridad y uso.
2. Mantenga este manual a mano para
que pueda consultarlo cuando tenga
alguna duda. Si tiene cualquier duda
que no esté cubierta en este manual,
consulte en la tienda donde adquirió
el producto.
3. Asegúrese de incluir siempre este
manual al vender, prestar o transferir
la propiedad de este producto.
4. Nunca permita que niños u otras
personas que no sean capaces de
comprender cabalmente las
instrucciones que se dan en el
manual utilicen la máquina.
■ CONDICIONES DE TRABAJO
1. Al utilizar el producto, asegúrese de
usar la vestimenta y el equipo de
protección adecuados.
(1) Casco
(2) Protectores para los oídos
(3) Gafas protectoras o protector facial
(4) Guantes de trabajo gruesos
(5) Botas de trabajo con suela
antideslizante
2 Asegúrese de llevar con usted los
siguientes elementos:
(1) Herramientas y limas incluidas
(2) Combustible de reserva
(3) Hoja de repuesto
(4) Elementos para marcar su área de
trabajo (cuerdas, letreros de
advertencia)
(5) Silbato (para colaboración o
situaciones de emergencia)
(6) Hacha pequeña o sierra (para quitar
obstáculos)
3. No use ropa suelta, joyas, pantalones
cortos ni sandalias, y no trabaje
descalzo. No use nada que pueda ser
atrapado por las piezas móviles de la
unidad. Recójase el pelo,
asegurándose de que quede por
encima de sus hombros.
■ PRECAUCIONES
1. Nunca arranque el motor dentro de una
habitación cerrada o edificio. Los gases
de escape contienen monóxido de
carbono peligroso.
2. Nunca use el producto en los siguientes
casos:
a. Cuando el suelo sea resbaloso o
cuando usted no pueda mantener
una posición estable.
5. Sicherer Betrieb
5. Per un funzionamento sicuro
5. Instrucciones de seguridad
English Français
18
be difficult to gain a clear view of the
working area.
c. During rain storms, during lightning
storms, at times of strong or gale-
force winds, or at any other times
when weather conditions might make
it unsafe to use the product.
■ WORKING PLAN
1. You should never use the product when
under the influence of alcohol, when
suffering from exhaustion or lack of
sleep, when suffering from drowsiness
as a result of having taken cold
medicine or at any other time when a
possibility exists that your judgment
might be impaired or that you might not
be able to operate the product properly
and in a safe manner.
2. When planning your work schedule,
allow plenty of time to rest. Limit the
amount of time over which the product
is to be used continuously to
somewhere around 30–40 minutes per
session, and take 10–20 minutes of rest
between work sessions. Also try to
keep the total amount of work
performed in a single day under 2 hours
or less.
1. If you don’t observe the working
time, or working manner (See
■USING THE PRODUCT), Repetitive
Stress Injury(RSI) could occur.
If you feel discomfort, redness and
swelling of your fingers or any other
part of your body, see a doctor
before getting worse.
2. To avoid noise complaints, in
general, operate product between
8a.m. and 5p.m. on weekdays and
9a.m. to 5p.m. weekends.
Check and follow the local regulations as
to sound level and hours of operations for
the product.
■ BEFORE STARTING THE ENGINE
1. Operate the chain saw only in well
ventilated areas. Never start or run the
engine inside a closed room or building.
Exhaust fumes contain dangerous
carbon monoxide.
2. The area within a perimeter of 15 m of
the person using the product should be
NOTE
WARNING
une position correcte.
b. La nuit, par temps de brouillard ou
lorsque la visibilité ou le champ de
vision empêche de voir clairement la
zone de travail.
c. Pendant les averses, les orages
avec éclairs, par grands vents ou
toute autre condition climatique
rendant l’utilisation de la machine
dangereuse.
■ PLAN DE TRAVAIL
1. Ne jamais utiliser la machine sous
l’influence de l’alcool ou en état de
faiblesse due à la fatigue, au manque
de sommeil, à la prise de médicament
ou à tout autre moment où l’on n’est
pas réellement capable de l’utiliser
correctement et en toute sécurité.
2. Lors de l’élaboration du plan de travail,
prévoir suffisamment de temps de
repos. Limiter la durée des périodes
pendant lesquelles la machine est
utilisée sans interruption entre 30 et 40
minutes. Se reposer de 10 à 20 minutes
entre ces périodes. Autant que
possible, essayer de limiter ce genre de
travail à 2 heures par jour.
1. Si ce plan de travail et cette méthode
de travail ne sont pas respectés, un
accident dû au stress répétitif peut
se produire (voir ■UTILISATION DE
LA MACHINE).
Si l’on ressent un malaise ou si les
doigts ou tout autre membre
rougissent et enflent, consulter un
docteur avant que cela ne s’aggrave.
2. Pour éviter les problèmes de bruit
avec le voisinage, utiliser
généralement la machine entre 8 et
17 heures pendant la semaine et de 9
à 17 heures les fins de semaine.
Vérifier et suivre la réglementation locale
sur le niveau de bruit et les horaires
d’utilisation de ce type de machine.
■ AVANT DE METTRE LE MOTEUR EN
MARCHE
1. La tronçonneuse ne doit être utilisée
qu'en plein air ou dans un local bien
ventilé. Ne jamais mettre en marche ou
laisser tourner le moteur dans un local
fermé. Les gaz d'échappement sont
dangereux car ils contiennent du
REMARQUE
AVERTISSEMENT
5. For safe operation 5. Consignes de securite
EspañolDeutsch Italiano
19
anderen Bedingungen, die die Sicht
im Arbeits- und Sicherheitsbereich
einschränken und einen sicheren
Betrieb verhindern.
c. Bei starkem Niederschlag, Gewitter,
stürmischem Wind oder anderen
Wetterbedingungen, die einen
sicheren Einsatz dieses Produktes
unmöglich machen.
■ ARBEITSPLAN
1. Sie sollten das Produkt keinesfalls unter
Einfluß von Alkohol, bei Erschöpfung
oder Übermüdung, bei Schläfrigkeit
aufgrund der Einnahme von
Erkältungsmitteln oder dann benutzen,
wenn die Möglichkeit besteht, daß Ihr
Urteilsvermögen beeinträchtigt ist oder
Sie nicht imstande sind, das Produkt
einwandfrei und sicher zu bedienen.
2. Beim Planen der Arbeitseinsätze,
genügend Ruhephasen
berücksichtigen. Begrenzen Sie die
Zeitdauer, die die vorgesehenen 30 –
40 Minuten pro Arbeitseinsatz bei
kontinuierlichem Betrieb überschreitet
und zwischen den Einsätzen jeweils
Pausen von 10 – 20 Minuten einlegen.
Die gesamte Arbeitszeit sollte täglich
unter 2 Stunden oder weniger liegen.
1. Wenn Sie die Arbeitszeit oder die
Arbeitsweise nicht beachten (Siehe
■ANWENDUNG DES PRODUKTS),
könnten Verletzungen aufgrund sich
wiederholenden Stresses (RSI)
verursacht werden.
Wenn Sie sich nicht wohl fühlen,
wenn Ihre Finger oder ein anderes
Körperteil rot und angeschwollen ist,
suchen Sie einen Arzt auf, bevor es
schlimmer wird.
2. Um Lärmbelästigung zu verhindern
sollte das Gerät im allgemeinen
werktags zwischen 8.00 und 17.00
und am Wochenende zwischen 9.00
und 17.00 Uhr verwendet werden.
Prüfen und befolgen Sie die örtlichen
Bestimmungen für dieses Produkt und die
Betriebsstunden.
■ VOR DEM START DES MOTORS
1. Die Kettensäge nur in einem gut
beiüfteten Arbeitsbereich benutzen,
Den Motor niemals in geschlossenen
Räumen oder Gebäuden laufen lassen.
Die Auspuffgase enthalten gefährliches
Kohlenmonoxid-Gas.
2. Der Gefahrenbereich während des
HINWEIS
WARNUNG
b. Di notte, quando c’è molta nebbia o
in altre occasioni quando il campo
visivo è limitato ed è difficile avere
una visione nitida dell’area di lavoro.
c. Durante la pioggia, durante una
tempesta, quando tira un vento molto
forte o in altre occasioni in cui le
condizioni meteorologiche rendono
poco sicuro l’utilizzo del prodotto.
■ PIANO DI LAVORO
1. Non usate mai il prodotto sotto
l’influenza dell’alcool, se siete stanchi o
assonnati; se siete in uno stato di
sonnolenza per via dell’assunzione di
farmaci o in altre occasioni in cui vostro
giudizio può essere ridotto,
impedendovi così di usare il prodotto in
modo corretto e sicuro.
2. Quando pianificate il lavoro, non
dimenticate di fornire del tempo per
riposare. Limitate il tempo di utilizzo del
prodotto a 30 — 40 minuti per sessione
e riposatevi da 10 a 20 minuti tra le
sessioni di lavoro. Inoltre, cercate di
mantenere la quantità totale del lavoro
effettuato durante la giornata a 2 ore o
meno.
1. Se non osservate il tempo di lavoro o
il modo di lavoro. (Fate riferimento
alla sezione ■ UTILIZZO DEL
PRODOTTO), si possono verificare
delle lesioni per via di sforzi continui
(RSI). Se sentite del disagio, oppure
se le dita od altre parti del corpo si
arrossiscono o si gonfiano,
consultate un medico prima che la
situazione peggiora.
2. Per evitare dei problemi dovuti alla
generazione di rumore, usate il
prodotto tra le ore 8 antimeridiane e
le ore 5 pomeridiane nei giorni feriali
e dalle ore 9 antimeridiane e le 5
pomeridiane nei giorni festivi.
Controllate ed osservate le norme locali
sul livello sonoro e sulle ore operative del
prodotto.
■ PRIMA DI ACCENDERE IL MOTORE
1. Lavorate solo in ambienti bene aerati.
Non utilizzate la motosega in luoghi
chiusi. I gas di scarico contengono
monossido di carbonio velenoso.
2. L’area all’interno di un perimetro di 15
m dalla persona usando il prodotto va
considerata una zona pericolosa in cui
NOTA
AVVERTIMENTO
b. Durante la noche, cuando haya
niebla densa, o en cualquier otra
situación en que su campo de visión
esté limitado y sea difícil lograr una
adecuada visión del área de trabajo.
c. Durante tormentas de lluvia,
tormentas eléctricas, tormentas de
viento, o en cualquier otra
circunstancia en que las condiciones
climáticas puedan hacer inseguro el
uso del producto.
■ PLAN DE TRABAJO
1. Nunca utilice el producto cuando se
encuentre bajo la influencia del alcohol,
cuando sufra de fatiga o falta de sueño,
cuando sienta somnolencia debido a
que ha tomado una medicina para el
resfrío, o en cualquier otra situación
que pueda afectar su juicio y usted no
sea capaz de utilizar el producto
correctamente y de manera segura.
2. Al planificar su trabajo, deje un tiempo
suficiente para descansar. Limite el
tiempo de uso continuo del producto a
30–40 minutos por sesión, y tome
descansos de 10–20 minutos entre las
sesiones de trabajo. Asimismo, trate de
que la cantidad total de trabajo diario
sea inferior a 2 horas.
1. Si no sigue las recomendaciones en
cuanto a la duración del trabajo o a
la forma de trabajar (consulte ■USO
DEL PRODUCTO), usted podrá sufrir
una lesión por esfuerzo repetido
(RSI).
Si siente algún malestar, si sus
dedos o cualquier otra parte de su
cuerpo enrojecen o se hinchan,
consulte oportunamente a un
médico.
2. Para evitar problemas de ruido, en
general utilice el producto entre las 8
a.m. y las 5 p.m. los días laborables,
y de 9 a.m. a 5 p.m. durante el fin de
semana.
Compruebe y respete las disposiciones
locales respecto de los niveles de ruido y
horas de uso del producto.
■ ANTES DE ARRANCAR EL MOTOR
1. Utilice la motosierra sólo en lugares con
ventilación adecuada. Nunca haga
arrancar el motor en un lugar cerrado o
dentro de un edificio. Los gases del
escape contienen monópxido de
carbono, que es una sustancia
sumamente peligrosa.
NOTA
ADVERTENCIA
5. Sicherer Betrieb
5. Per un funzionamento sicuro
5. Instrucciones de seguridad
English Français
20
considered a hazardous area into which
no one should enter. If necessary
yellow warning rope, warning signs
should be placed around the perimeter
of the area. When work is to be
performed simultaneously by two or
more persons, care should also be
taken to constantly look around or
otherwise check for the presence and
locations of other people working so as
to maintain a distance between each
person sufficient to ensure safety.
3. Check the condition of working area to
avoid any accident by hitting hidden
obstacles such as stumps, stones,
cans, or broken grass.
Remove any obstacle before beginning
work.
4. Inspect the entire unit for loose
fasteners and fuel leakage. Make sure
that the cutting attachment is properly
installed and securely fastened.
5. Always use the shoulder strap. Adjust
the strap for comfort before starting the
engine. The strap should be adjusted
so the left hand can comfortably hold
the handlebar grip approximately waist
high.
■ STARTING THE ENGINE
1. Keep bystanders and animals at least
15 m away from the operating point. If
you are approached, immediately stop
the engine.
2. The product is equipped with a
centrifugal clutch mechanism, so the
cutting attachment begins to rotate as
soon as the engine is started by putting
the throttle into the start position. When
starting the engine, place the product
onto the ground in a flat clear area and
hold it firmly in place so as to ensure
that neither the cutting part nor the
throttle come into contact with any
obstacle when the engine starts.
Never place the throttle into the high
speed position when starting the
engine.
3. After starting the engine, check to make
sure that the cutting attachment stops
WARNING
IMPORTANT
monoxyde de carbone.
2. La zone dans un rayon de 15 mètres
autour de l’opérateur est considérée
comme dangereuse et personne ne doit
s’y trouver. Si nécessaire, délimiter le
périmètre de la zone de travail avec du
ruban de marquage (rouge fluorescent
et blanc par exemple) et poser des
panneaux d’avertissement. Lorsque
deux ou plusieurs personnes travaillent
ensemble ou à proximité, chacune doit
constamment faire attention et garder
ses distances par rapport aux autres
pour assurer une sécurité satisfaisante.
3. Vérifier constamment l’état de la zone
de travail pour éviter tout accident dû
aux impacts avec des obstacles tels
que les souches, les pierres, les boîtes
de conserves ou débris de verre.
Retirer tout obstacle avant de commencer
le travail.
4. Vérifier que la machine ne comporte
aucun élément desserré ou de fuite de
carburant. S’assurer que l’outil de
coupe est monté correctement et bien
serré.
5. Utiliser toujours la machine avec son
harnais. Le régler pour un confort
maximal avant de mettre le moteur en
marche. Il doit être ajusté pour que la
main gauche puisse tenir
confortablement la poignée environ à
hauteur de la taille.
■ DEMARRAGE DU MOTEUR
1. Empêcher toute personne ou animal de
s’approcher à moins de 15 mètres. Si
quelqu’un s’approche trop près, arrêter
aussitôt le moteur.
2. La machine est équipée d’un
embrayage centrifuge et l’outil de coupe
se met à tourner dès que le moteur est
mis en route en plaçant l’accélérateur
en position de démarrage. Pour mettre
le moteur en route, poser et maintenir
fermement la machine à plat sur le sol
dans un endroit dégagé où aucun
obstacle ne peut entrer en contact avec
l’outil de coupe ou la manette
d’accélérateur une fois que le moteur
sera en marche.
Ne jamais mettre la manette de
l’accélérateur à fond lors de la mise en
marche.
3. Une fois le moteur en marche, vérifier
AVERTISSEMENT
IMPORTANT
5. For safe operation 5. Consignes de securite
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Zenoah Pole Saw PSZ2600 Manuale utente

Zenoah
Marca
Zenoah
Modello
Pole Saw PSZ2600
Tipo
Manuale utente
Questo manuale è adatto anche per
Scarica il pdf
rapporto

in altre lingue

Documenti correlati

Altri documenti