Covidien Kendall SCD 700 Series Operation And Service Manual

Marca: Covidien

Modello: Kendall SCD 700 Series

Tipo: Operation And Service Manual

Kendall SCD

™

700 Sequential Compression System

Operation and Service Manual

700 Système de compression séquentielle

- Manuel d’utilisation et d’entretien

700 Sequenzielles Kompressionssystem

- Bedienungs- und Servicehandbuch

Sistema di compressione sequenziale 700

- Manuale d’uso e di manutenzione

Sistema de compresión secuencial 700

- Manual de funcionamiento y mantenimiento

700 Sekventiellt kompressionssystem

- Användar- och servicehandbok

700 sequentieel compressiesysteem

- Bedienings- en onderhoudshandleiding

Sistema de Compressão Sequencial 700

- Manual de Funcionamento e Assistência

700 jaksoittainen kompressiojärjestelmä

- Käyttö- ja huolto-ohjekirja

700 Sekventielt kompressionssystem

- Bruger- og servicevejledning

Σύστημα διαδοχικής συμπίεσης 700

- Εγχειρίδιο λειτουργίας και σέρβις

Sekvenční kompresní systém 700

- Uživatelská a servisní příručka

700 Szekvenciális kompressziós rendszer

- Kezelési és szervizelési kézikönyv

700 Система терапевтическая для

последовательной компрессии

- Руководство по эксплуатации и

обслуживанию

System stopniowanego ucisku 700

- Podręcznik obsługi i serwisu

700 Sıralı Kompresyon Sistemi

- Çalıştırma ve Servis El Kitabı

700 Sekvensielt kompresjonssystem

- Bruker- og servicehåndbok

Sekvenčný kompresný systém 700

- Príručka na obsluhu a servis

Sistem de compresie secvenţială 700

- Manual de operare şi întreţinere

Система за последователна компресия 700

- Ръководство за работа и сервиз

Kendall SCD 700 Series

TABLE OF CONTENTS

Indications ..................................................................................................................... EN-1

Leg Compression .................................................................................................................................................... EN-1

Foot Compression ................................................................................................................................................... EN-1

Contraindications ........................................................................................................... EN-1

Leg Compression ................................................................................................................................................... EN-1

Foot Compression ................................................................................................................................................... EN-1

Cautions and Warnings ................................................................................................... EN-2

Explanation of Symbols ................................................................................................... EN-2

Front Panel Display ......................................................................................................... EN-3

Section I - General Operating Instructions ........................................................................ EN-4

Set up ...................................................................................................................................................................... EN-4

Start-up .................................................................................................................................................................. EN-4

Garment Selection and Verification ....................................................................................................................... EN-4

Normal Operation and Pressure Adjustment ........................................................................................................ EN-6

Vascular Refill Detection ........................................................................................................................................ EN-6

Shutdown ............................................................................................................................................................... EN-6

Garment Compatibility .......................................................................................................................................... EN-7

Section II - Compliance Meter .......................................................................................... EN-8

Introduction ............................................................................................................................................................ EN-8

Accessing the Compliance Meter ........................................................................................................................... EN-8

Checking the Compliance Meter ............................................................................................................................ EN-9

Section III - Battery Operation .......................................................................................EN-11

Unit plugged in and Powered On (Charging) ......................................................................................................EN-11

Unit not plugged in and Powered On (Operating on Battery) ........................................................................... EN-11

Unit Powered Off (charging when plugged in) ................................................................................................. EN-12

Charging the Battery ........................................................................................................................................... EN-12

Battery Warnings ................................................................................................................................................. EN-12

Section IV - Fault Conditions and Troubleshooting ...........................................................EN-13

Section V - Service and Maintenance ..............................................................................EN-16

Introduction ......................................................................................................................................................... EN-16

Warranty and Factory Service ............................................................................................................................. EN-17

Disposal ................................................................................................................................................................ EN-17

Service Precautions .............................................................................................................................................. EN-17

Fan Filter, Exhaust Filter and Ventilation .............................................................................................................. EN-17

Fuses ..................................................................................................................................................................... EN-18

Suggested Preventative Maintenance Schedule ................................................................................................EN-18

Error History .......................................................................................................................................................... EN-18

Cleaning ...............................................................................................................................................................EN-18

Controller Cleaning ............................................................................................................................................... EN-18

Tube Set Cleaning ................................................................................................................................................. EN-19

Electrical/Electronics Description ........................................................................................................................ EN-19

Pneumatic Operation Description ....................................................................................................................... EN-19

Section VI - Test Methods and Calibration ........................................................................EN-19

Test Mode Look up Chart...................................................................................................................................... EN-20

Test Mode T1 - Burn-In ........................................................................................................................................EN-20

Test Mode T2 - General Function Test ................................................................................................................. EN-20

Test Mode T3 - Pressure Transducer Calibration ................................................................................................... EN-20

Kendall SCD 700 Series

TABLE OF CONTENTS

Test Mode T4 - Pressure Transducer Calibration Verification ................................................................................EN-21

Test Mode T5 - Self Test ....................................................................................................................................... EN-21

Test Mode T6 - Performance Test ......................................................................................................................... EN-21

Test Mode T7 - Manufacturing Test ......................................................................................................................EN-22

Test Mode – Error History .................................................................................................................................... EN-22

Section VII - General Disassembly / Reassembly ...............................................................EN-22

Battery Pack (Removal / Installation - see Figure 9) .......................................................................................... EN-22

Compressor (Removal / Installation - see Figure 11) .........................................................................................EN-22

Muffler (Removal / Installation) ......................................................................................................................... EN-23

Valve Manifold (Removal / Installation) .............................................................................................................EN-23

Power Supply Board (Removal / Installation) ....................................................................................................EN-23

Fan, Fan Filter and Exhaust Filter (Removal / Installation - see Figure 9) .......................................................... EN-23

Main CPU Board and Graphical Display (Removal/Installation - see Figure 9) .................................................EN-24

Adjustable Bed Hook (Removal/Installation) .....................................................................................................EN-24

Section VIII - Parts Listing ...............................................................................................EN-25

Section IX - Specifications ...............................................................................................EN-26

Kendall SCD 700 Series Compression System .....................................................................................................EN-26

Section X - Schematics ...................................................................................................EN-29

Figure 9 - Parts Assembly Diagram – Exploded view (Page 1 of 2) ................................................................. EN-29

Figure 9 - Parts Assembly Diagram (front enclosure)– Exploded view (Page 2 of 2) .......................................EN-30

Figure 10 - Pneumatic & Electrical Schematic ....................................................................................................EN-31

Figure 11 - Rear Enclosure View........................................................................................................................... EN-32

Figure 12 - Front Enclosure View ......................................................................................................................... EN-33

EN-1

Kendall SCD 700 Series

Indications

The Kendall SCD 700 sequential compression system (hereby referenced as “Kendall SCD 700 series”) is designed to

apply intermittent pneumatic compression to increase venous blood flow in at-risk patients in order to help prevent

deep vein thrombosis and pulmonary embolism. The System consists of the controller, the tubing sets (provided

with the controller) and single-patient use garments (purchased separately from this controller). The garments, both

leg sleeves and foot cuffs, compress the limbs to enhance venous blood movement. After the compression cycle has

reached set pressure, the controller measures the time it takes for the limbs to refill with blood and waits that period

of time before the next compression is initiated.

Leg Compression

The use of the Kendall SCD 700 series compression system with leg sleeves is indicated for:

1. Deep vein thrombosis and pulmonary embolism prophylaxis.

Foot Compression

The use of the Kendall SCD 700 series compression system with foot cuffs is indicated for:

1. Circulation enhancement.

2. Deep vein thrombosis prophylaxis.

3. Edema - Acute.

4. Edema - Chronic.

5. Extremity pain incident to trauma or surgery.

6. Leg Ulcers.

7. Venous stasis / venous insufficiency.

If you need further information regarding the Kendall SCD 700 series compression system or its clinical benefits,

please contact your Covidien Sales Representative.

Contraindications

Leg Compression

The Kendall SCD 700 series compression system may not be recommended for use with leg sleeve on patients with

the following:

1. Any local leg condition in which the sleeves may interfere, such as: (a) dermatitis, (b) vein ligation [immediate

postoperative], (c) gangrene, or (d) recent skin graft.

2. Severe arteriosclerosis or other ischemic vascular disease.

3. Massive edema of the legs or pulmonary edema from congestive heart failure.

4. Extreme deformity of the leg.

5. Suspected pre-existing deep venous thrombosis.

Foot Compression

The Kendall SCD 700 series compression system may not be recommended for use with foot cuffs on patients with the

following:

1. Conditions where an increase of fluid to the heart may be detrimental.

2. Congestive heart failure.

3. Pre-existing deep vein thrombosis, thrombophlebitis or pulmonary embolism.

Use with caution on the infected or insensitive extremity.

EN-2

Kendall SCD 700 Series

Cautions and Warnings

1. Federal (USA) law restricts this device to sale by or on the order of a physician.

2. Patients with diabetes or vascular disease require frequent skin assessment.

3. Explosion hazard. Not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen

or nitrous oxide.

4. No modification of this equipment is allowed. It is acceptable to service and repair the components identified as

serviceable in this document.

5. Although training on the use of the device is recommended, no special skills are required.

6. WARNING: Do not operate the controller if the power cord is damaged.

7. WARNING: Do not attempt to repair or replace broken tubing connectors as hazardous inflation of the sleeves

may occur.

8. WARNING: To avoid the risk of electric shock, this equipment must only be connected to supply mains with

protective earth.

9. WARNING: Do not position the controller so that it is difficult to disconnect the power cord from the AC outlet.

Explanation of Symbols

Caution, consult

accompanying documents.

Not made with natural rubber latex.

Consult instructions for use.

Federal (USA) law restricts this device to sale by

or on the order of a physician.

Reorder number for the device located

on the carton label.

Use by

Use By

0123

CE Mark

Device has not been subjected

to a steilization process.

Batch Code

Controller Symbols

Controller serial number

Manufacturing date code

Keep away from sunlight.

Keep dry.

Type BF protection against

electronic shock.

15%

85%

Humidity limitations

Manufacturer

-4°F

-20°C

131°F

55°C

Store between these temperatures.

WEEE (Waste from electrical

and electronic equipment)

Protection against uid ingress: spraying water

Protective earth (ground)

Protection against uid ingress: spraying water

and particulates

Equipotential ground point

EN-3

Kendall SCD 700 Series

MEDICAL EQUIPMENT 47DA

UL60601-1, ANSI/AAMI ES60601-1:2005,

CAN/CSA C22.2 NO.601.1,

CAN/CSA C22.2 NO.60101-1 (2008).

Medical- general medical equipment as to electrical shock, re and mechanical

hazards only in accordance with UL60601-1, ANSI/AAMI ES60601-1:2005,

CAN/CSA C22.2 NO.601.1, CAN/CSA C22.2 NO.60101-1 (2008).

Sterile Garment Symbols

Sterile using

ethylene oxide.

Single use device

Do not use if package is opened or damaged.

Tubing Set Symbols

Device contains phthalates.

Constructed from recyclable materials.

Front Panel Display

Item Explanation Item Explanation

1 Power On Indicator 5 Battery Status Indicators 1-3

2 Power On/Standby Button 6 Right Arrow Button

3 A - Button 7 B - Button

4 AC Power/Battery

Charging Indicator

EN-4

Kendall SCD 700 Series

Section I - General Operating Instructions

Set up

Bed

Foot

Board

• Placethecontrolleronthefootboard.Thisisdonebygraspingthedevice

handle and the top portion of the pivoting bed hook and squeezing to open

the gap. Place it on the foot board so it straddles the foot board and release

the bed clamp. See the figure at right. Ensure its security. Alternatively, the

device can be placed on a horizontal surface appropriate for the environment,

such as on a table, within reasonable proximity to the point of use. Be sure

to allow adequate air flow to the vents located at the power cord cover and

below the tube set connection points.

• Thecontrollercanoperatewithoneortwogarmentsattachedtothepatient.

• Plugthetubingset(s)intothebackofthecontroller.Routethetubingtoward

the patient’s limbs, being careful to leave access ways clear and eliminate

tripping hazards.

• Plugthetubesintogarment(s)wrappedontothepatient’slimbs.

• Matchtheleftandrightports,markedBandArespectively,withtheleftandrightlimbsofthepatient.Although

the operation of the controller is not affected, troubleshooting can be easier. Check tubing set(s) for kinking and

secure attachment at the controller and the garment(s).

• Plugthecontrollerpowercordintoaproperlygroundedhospitalgradereceptacle.TheblueACPowerIndicator

will illuminate. If no AC Power is accessible, the controller can be run using its own internal battery power.

• Ifcompliancemonitoringisdesired,refertoSectionII.

Start-up

• PressthePowerOn/Standbybuttontobeginnormaloperation.Ifusinglegsleeves,nofurtheruserintervention

is required unless there is a fault condition detected or if therapy must be discontinued.

• Thecontrollerwillbeep,flashalltheLED’sandilluminatethedisplayscreen.Quickinternaldevicechecksare

performed, which may be audible to the user.

• ThepumpwillbegintooperateaspartoftheGarmentSelectionandVerificationprocedure.

• DetectionofinoperativeLED’s,displayscreenandtheaudibleerrorindicationfunctionatstart-upisthe

user’s responsibility.

Garment Selection and Verification

After startup, the Garment Configuration procedure allows the user to select when foot compression is required at

either of the two controller ports:

• Onthedisplay,thePortALegandPortBLegimagesblinktoindicatethedefaultgarmentconfiguration(leg

compression).

• PressingeithertheAorBButtonwillcausethecorrespondingport’slegimagetoshifttoafootimagetosignify

foot compression. The buttons must be pressed for each port that is connected to a foot cuff to turn on the cor-

responding foot image(s).

Note: Leg sleeve compression is the default configuration when the controller is first powered on. Therefore, the A

and B Button(s) do not have to be pressed to begin compression therapy when leg sleeves are being used.

The A and B buttons need to be pressed only when foot compression is to be used.

NOTE: If a garment is attached anytime after the Garment Detection procedure has started, the system must be

restarted to ensure that the proper therapy will be applied to the limb(s).

Also after startup, the controller immediately begins conducting the Garment Selection and Verification procedure at

each port to determine if the garments have been properly attached to the controller:

EN-5

Kendall SCD 700 Series

• Ifnecessary,priortothecompletionofGarmentSelectionandVerification,theAandBButton(s)maybepressed

again to shift the garment image from the foot to the leg.

• Duringthisphase,thecompressorandvalvesareoperatingandairisdeliveredoutthecontrollerportstodetect

the number and type(s) of garment(s) connected [Leg Sleeve(s) and/or Foot Cuff(s)].

• IfthecontrollersensesaproperlyattachedgarmentandthetypeofgarmentdetectedmatchestheUser-selected

garment (or the default) configuration, then the corresponding image of a Leg Sleeve or Foot Cuff for both the A

or B side will be displayed on the screen.

• IfthecontrollersensesaproperlyattachedgarmentbutthetypeofgarmentdetecteddoesnotmatchtheUser-

selected garment (or the default) configuration, then a Garment Mismatch error is triggered. Garment Mismatch

errors can be corrected by pushing the corresponding A and B buttons to change the User-selected garment type

(Leg or Foot). In the example below, the screen shows Foot Cuffs and indicates the user must press both A and B

buttons (FIGURE 1).

A B

FIGURE 1

• OncetheGarmentDetectionprocedureiscompletedandanygarmentmismatcherrorsareaddressed,theAandB

button(s) will be disabled and normal operation begins by starting the compression therapy.

• Ifonlyonecontrollerportisconnectedtoagarmentforsingle-limbcompression,thentheUser-selectedgarment

(or the default) configuration setting (Leg or Foot) for the open port will be ignored and both the leg and foot will

be grayed out such as the example shown below (FIGURE 2).

A B

FIGURE 2

• Ifanygarmentsarenotproperlydetectedorifnogarmentsareattachedtothecontroller,thesystemwilltrigger

an E12 error. See section IV (Fault Conditions and Troubleshooting) in this manual. Check the garment application

and tubing connections. In this case, either the system can be turned off and restarted or the corresponding A and

B Button(s) can be pressed to confirm problem resolution and operation will continue without having to power

the controller down and restarting.

EN-6

Kendall SCD 700 Series

Normal Operation and Pressure Adjustment

• Verifythatthecorrespondinggarmentimagesmatchthedisposablegarment(s)appliedtothepatient.

• Thecontrollerautomaticallybeginstheprocessofapplyingintermittentcompressionalternatingbetweenlimbs

or to one if only one garment is applied.

• Onsuccessivecycles,thecontrollerautomaticallyadjustsitsoperatingparameterstomaintainsetpressure.

• Thepressuresettingdependsonthetypeofgarment:45mmHgforLegSleeves;130mmHgforFootCuffs.

Vascular Refill Detection

• TheKendallSCD700seriescompressionsystemincorporatesCovidien’spatented“VascularRefillDetection”

method to customize the therapy for each patient’s physiology. This system measures the time it takes for the

veins in the limb to refill after having been compressed by the system. The time is then used in subsequent cycles

as the time between compressions.

• VascularRefillDetectionoccursautomaticallyandrequiresnooperatorinteraction.

• TheVascularRefillDetectionmethodisusedwhenfirstpoweringontheSystemafteritreachessetpressureand

every thirty minutes thereafter.

• DuringtheentiretimeVascularRefillDetectionisinprogress,arotatingringsymbolwilldisplayinthecenterof

the screen as shown below in Figure 3. This symbol is informative only. No action is required by the user dring the

Vascular Refill Detection Process.

• Themethodworksbestwhenthepatientisstill,howeveritwillaccommodatemovement.

• IfanerrorisdetectedduringanymeasurementorifthecompressionisnotwithintheSystempressurespecifica-

tions, the refill time measurement will be repeated after the next compression cycle.

• Thetimebetweencompressionsonthesamelimbwillneverbeshorterthantwentysecondsorlongerthansixty

seconds.

• Ifbothcontrollerportsarebeingused,thenthelongerofthetwomeasurementswillbeusedtoadjustthetime

between cycles.

FIGURE 3

Shutdown

To terminate the operation, press the Power On/Standby button on the device.

EN-7

Kendall SCD 700 Series

Garment Compatibility

The Kendall SCD 700 series compression system is designed for use with Kendall SCD garment Reorder Codes:

Kendall SCD Sequential Compression

Comfort Sleeves

74010 Thigh Length X-Small

74011 Thigh Length Small

74012 Thigh Length Medium

74013 Thigh Length Large

74021 Knee Length Small

74022 Knee Length Medium

74023 Knee Length Large

Express Sleeves

9529 Knee Length Medium

9530 Thigh Length Medium

9545 Thigh Length Small

9736 Thigh Length Medium (sterile)

9780 Thigh Length Large

9789 Knee Length Large

9790 Knee Length X-Large

73011 Thigh Length Small

73012 Thigh Length Medium

73013 Thigh Length Large

73022 Knee Length Medium

73023 Knee Length Large

Kendall SCD Sequential Compression

Comfort Tear-Away Sleeves

74041 Thigh Length Small

74042 Thigh Length Medium

74043 Thigh Length Large

Express Foot Cuff

5897 Regular

5898 Large

73032 Regular

73033 Large

Express Tear-Away Sleeves

9530T Thigh Length Medium

9545T Thigh Length Small

9780T Thigh Length Large

73041 Thigh Length Small

73043 Thigh Length Large

73042 Thigh Length Medium

Further instructions for garment application and use are included with the Leg Sleeve and Foot Cuff packaging.

Tubing Set Compatibility

The garments connect to the controller via the Tubing Sets provided with the controller. Additional or replacement

Tubing Sets are available as Reorder Code 9528. The Extension Tubing Sets are also available as Reorder Code 9595.

EN-8

Kendall SCD 700 Series

Section II - Compliance Meter

Introduction

The Kendall SCD 700 series controller has a feature called the Compliance Meter, that can be used to monitor the

amount of time a patient receives compression therapy either by shift, day or during an entire hospital stay. This

unique feature operates in the background, so that it does not interrupt daily normal operation. Prior to using the

compliance meter, confirm the controller has been set up as described in Section I.

Time is tracked using a numerator/denominator arrangement. The denominator (bottom number) is the elapsed time

since the last Compliance Meter reset or can be chosen to show a moving window of time, such as a nurse shift. The

numerator (top number) is the patient therapy time. It is the amount of time that compression therapy was applied to

the patient during the elapsed period of time specified in the denominator. The time is expressed in hours and minutes.

Any time the controller is turned off or an error condition is present, thus halting normal operation, the therapy time

(numerator) will not increment, but the elapsed time will increment. The maximum amount of time that can be

displayed is 999 hours. After the controller is off for 40 days continuously, the Compliance Meter will reset to zero.

The Compliance Meter features are shown below:

Therapy time (top number)

(HHH:MM)

Elapsed time

(bottom number)

(HHH:MM)

A - button

(shift selector)

B - button

(reset button)

Right arrow

button

Shift

selections

Reset icon

FIGURE 4

Selection

Indicator

Resetting the Compliance Meter

• TheComplianceMetercanbeaccessedwhenthecontrollerisonandisdeliveringtherapy.Thecontrollerwill

sound a “deny” tone, three quick beeps, at any other time such as immediately after turning the system on and

garment detection is in progress (garments blinking). Note: use of the Compliance Meter does not halt or

otherwise affect the ongoing compression therapy.

• ResettheComplianceMetertozero:

◊ Access the Compliance Meter by pressing the Right Arrow button. Pressing it again will return the user to

normal operating mode. If the Compliance Meter is accessed, but no further action is taken, then the system

will change the display back to normal operation mode in thirty seconds.

◊ Reset the Compliance Meter by pressing the B button. The confirmation screen will appear as shown in the

figure below (Figure 5). Press the A button to select check mark to confirm the reset operation. To decline the

reset, press the B button. After either A or B is pressed, the screen will revert to the Compliance Meter Screen.

FIGURE 5

Reset icon

Confirm reset

Deny reset

EN-9

Kendall SCD 700 Series

◊ If Compliance Meter reset is chosen, then the numerator and denominator will be reset to zero. The system

will begin recording time starting from zero.

◊ If a reset is not initiated, then the Compliance Meter continues its operation. This may result in inaccurate

compliance information for the patient. It is not recommended to reset the meter again until the device is

assigned to a new patient.

Accessing the Compliance Meter

• Atanytimeduringtheuseofthedevice,compliancetothetherapycanbechecked.Thiswillnotinterrupt

therapy.

• PresstheRightArrowButton.

• AscreensimilartoFigure4willbedisplayed.

• ThetopnumbershowninthemiddleofthescreenisthenumberofhoursofCompliancethatoccurredduringthe

period of time shown in the bottom number (elapsed time).

• Notethatinthelowerlefthandcornerofthescreen,therearenumbersandasymbolrepresentingtimedurations

of interest. 8, 10 and 12 are typical nurse shifts. 24 is a full day. The symbol Σ represents total compliance time

since the last reset.

• PressingtheAbutton(shiftselector)allowstheusertoselectatimedurationofinterest.Notethattheselection

indicator moves with each button press.

• Todeterminetheamountoftherapyapatienthasreceivedoverthemostrecent8hours,forexample,selectthe

‘8’ on the shift selector.

• Todeterminetheamountoftherapyapatientreceivedoverthemostrecent24hours,forexample,selectthe‘24’

on the shift selector.

• Beaware,iftheamountofelapsedtimehasnotyetreachedthetimeselectedontheshiftselector,thenthe

actual elapsed time will display in the bottom number.

• Notethatafter30secondsofinactivity,theComplianceMeterwillreturntothenormaltherapyscreen.

EN-10

Kendall SCD 700 Series

The example below shows a timeline of Compliance for a hypothetical patient. The 8 hour shift selection is active in this example:

Elapsed

Time

(hours)

0:00 2:30 3:30 6:30 7:00 8:00 18:00

0:00

2:30

3:30

5:30

6:30

5:30

7:00

6:30

8:00

16:30

18:00

Patient is

compliant

for 2

hours

Patient is

compliant

for an

additonal

3 hours

Patient sleeps

for 10 hours with

device on.

Nurse reapplies

system to patient

for 1 more hour

Nurse selects

“Σ” on the shift

selector. This

indicates how

much therapy

since the last

system reset.

Patient

goes to 1

hour test

Patient

turns device

o for half

an hour

Device is

reset

EN-11

Kendall SCD 700 Series

Section III - Battery Operation

The Kendall SCD 700 series compression system is designed to operate normally on AC line power or DC battery power

without interruption. There are three Battery Status Indicator LED’s used to represent the charge level of the battery.

Once the controller is powered on, it may take the system a few seconds to establish communication with the battery

and display the charge level. The battery Indicator shown below is located in the upper right hand corner of the user

interface. See FIGURE 6.

Warning: If the ground integrity of the mains power cable is in question, the device should be operated

on battery power until the ground integrity can be insured.

FIGURE 6

1 32

Battery Status Indicators

Unit plugged in and Powered On (Charging)

Battery State Battery Status 1 Battery Status 2 Battery Status 3

100% charge Green Green Green

67-99% charge Green Green Green (Pulsing)

34-66% charge Green Green (Pulsing) Off

0-33% charge Green (Pulsing) Off Off

Unit not plugged in and Powered On (Operating on Battery)

Battery State Battery Status 1 Battery Status 2 Battery Status 3

67-100% charge Green Green Green

34-66% charge Green Green Off

< 34% charge Green Off Off

15-40 minutes left* Amber (Flashing) Off Off

< 15 minutes left* Red (Flashing) Off Off

EN-12

Kendall SCD 700 Series

Unit Powered Off (charging when plugged in)

Battery State Battery Status 1 Battery Status 2 Battery Status 3

0 -100% charge Off Off Off

With 15-40 minutes of battery charge left, an audible error indicator will sound in a sequence of three beeps once

every two minutes. Once there is less than 15 minutes of battery charge left, the audible error indicator will sound

continuously and the dead battery icon will display as shown in FIGURE 7.

FIGURE 7

Charging the Battery

The battery will begin charging as soon as the unit is plugged into an AC power source. The amount of time required

to charge the battery will vary depending on the battery’s overall condition, age, and the controller’s state during

charging. For example, charging a new, fully drained battery will take approximately 4 hours with the controller

on standby and 8 hours with the controller powered on. The Battery Status indicators should always be used to

determine the state of charge for the battery. A fully charged battery will typically provide 6-8 hours of operation

time depending on the sleeve configuration, sleeve application, and the battery condition.

Note: If the operation time on battery power is extremely short the battery should be returned for service or

replacement.

Note: The battery performance may be reduced if it is left unused for extended periods of time. It is recommended

that the battery pack be stored with a minimum charge of 50% and kept near 25°C (77°F) if prolonged storage is

necessary.

Battery Warnings

The Kendall SCD 700 series compression system battery pack contains Lithium Ion (Li-Ion) battery cells and must be

used properly for safety and to maintain optimal performance.

• Storesparebatterypacksbetween–20°C(-4°F)and60°C(140°F).

• Donotdrop,impact,orimmerseinwater.

• Donottouchoringestanyleakingelectrolyte.Ifcontactoccurs,rinseskinand/oreyesimmediatelyandseek

medical attention if irritation develops. If ingested, contact local poison control center.

• Donotopenbattery,disposeofinfire,orshortcircuit.Doingsomaycausethebatterytoignite,explode,leak,or

become hot and cause personal injury.

• Disposeofimproperlyworkingordamagedbatterypacksaccordingtolocalregulations.

• ChargeonlywithspecifiedchargersaccordingtoCovidien’sinstructions.

EN-13

Kendall SCD 700 Series

Section IV - Fault Conditions and Troubleshooting

When the microprocessor detects a fault condition, it interrupts the normal operation of the controller, deactivates all

valves to vent the air from the garment(s), displays a fault code, and sounds an audible error indicator. If a Garment

Mismatch error is triggered the user may remedy the problem by pressing the corresponding A and B Button(s). Some

errors will remain active until the controller is turned off, or the battery runs out of charge (if operating on battery

power). Others can be reset once the user confirms the cause of the error and remedies the problem.

Error Types: Description Example

Service Required Error code is present because of a failed

internal component. It can not be

addressed by the user.

Manual Reset Required Error that can be troubleshot and

corrected by the user but requires the

device to be powered off and on. If the

error persists, then the controller requires

service.

A B

User Resettable This type of error allows the user to

remedy the issue and resume operation

by pressing the A and B button(s)

corresponding with the port affected

without powering the unit down. For

this type of error, a check mark will be

shown indicating what port is the area of

concern. A yellow triangle indicates a low

concern error. If the triangle is red it is

indicative of an error related to a pressure

that is high in an abnormal way. If the

error persists, then the controller requires

service.

A B

EN-14

Kendall SCD 700 Series

Error Codes

Error Code Error Type Description Troubleshooting

Garment Mismatch Error

User Resettable The Garment Detection

procedure has detected

a garment configuration

(Leg or Foot flashing green)

that does not match the

User-selected configuration

(Leg or Foot red).

Press the port

configuration button(s)

to turn the foot selection

on/off depending on

what type of garment(s)

is connected to the

controller. If the proper

garment is selected and

the problem persists have

the controller serviced by a

professional.

A B

System High Pressure Error

Manual Reset required System pressure has

exceeded 90 mmHg (Leg

sleeve) or 180 mmHg (Foot

Cuff).

Check for kinked tubes or

patient interference with

the garments, like pressing

foot against foot board.

A B

High Pressure (Leg Sleeves)

User Resettable Leg Sleeve pressure is

greater than 47 mmHg

for10consecutivecycles;

or pressure is above 65

mmHg for 5 consecutive

cycles.

Check for a tight leg

sleeve and adjust fit

appropriately. Also check

for a partially occluded

tube.

A B

High Pressure (Foot Cuffs)

User Resettable Foot Cuff pressure is

greater than 135 mmHg

for 10 consecutive cycles

or pressure is above 160

mmHg for 5 consecutive

cycles.

Check for a tight foot

cuff and adjust fit

appropriately. Also check

for a partially occluded

tube.

A B

Low Pressure (Leg Sleeves)

User Resettable Leg Sleeve pressure is

less than 43 mmHg for 10

consecutive cycles.

Check for leaks in the

sleeve or the tube

connections.

Low Pressure (Foot Cuffs)

User Resettable Foot Cuff pressure is less

than 125 mmHg after 10

consecutive cycles.

Check for leaks in the cuff

or the tube connections.

EN-15

Kendall SCD 700 Series

Error Code Error Type Description Troubleshooting

Low Pressure (Leg Sleeves)

User Resettable Leg Sleeve pressure is not

between 35 and 55 mmHg

for 12 consecutive cycles.

Check for leaks in the

sleeve or the tube

connections.

Low Pressure (Foot Cuffs)

User Resettable Foot Cuff pressure is not

between 110 and 150

mmHg for 12 consecutive

cycles.

Check for leaks in the cuff

or the tube connections.

Valve Feedback Error

Service Required If a valve electrically

malfunctions, this error

will be displayed.

Service Technician only:

Verify that the valve

assembly wires are

properly connected

and confirm solenoid

actuation.

Software Error

Service Required Upon startup, and

periodically during

operation the

microprocessor performs

diagnostic tests. If a

software error is detected,

this Error Indicator will be

triggered.

Return to Covidien for

service.

Compressor Error

Service Required If the compressor

electrically malfunctions

this error will be displayed.

Service Technician only:

Verify that the compressor

wires are properly

connected.

Vent Error

User Resettable The pressure in a garment

is greater than 20 mmHg

at the end of any vent

period.

Check tubing for kink or

occlusion. Check garment

application (too loose or

tight).

Service Technician only:

Check for kinked internal

tubing.

A B

EN-16

Kendall SCD 700 Series

Error Code Error Type Description Troubleshooting

Temperature Error

Manual reset required If the internal case

temperature of the

controller drops below

5°C (41°F) or exceeds 55°C

(131°F).

High temperature: Make

sure the controller is not

covered by bedding and

that the fan port, located

near the power cord is not

obstructed.

Low Temperature: Allow

the system to warm to

room temperature.

Battery Error

Service Required Safe battery operation of

the controller can not be

ensured.

Service Technician

Only: Ensure that an

unauthorized battery

pack replacement has not

been made. Replace pack

or return to Covidien for

service.

E10

Tubing Disconnect Error

User Resettable Pressure measured in

the inflatable garment is

below 10 mmHg for 10

consecutive cycles or no

garments are detected

during startup.

Check for disconnected

tube sets or garments and

reconnect.

A B

E12

Pressure Transducer Error

Service Required The system could not sense

a pressure rise of more

than 5 mmHg during an

inflation cycle or during

start up.

Service Technician Only:

Check the transducer tube

inside the controller and

ensure it is neither kinked

or disconnected.

E13

Low Battery Error

Recharge Battery There is less than 15

minutes of battery charge

remaining. The pump and

valves will continue to

operate for as long as there

is enough power.

Plug the controller into an

AC power outlet.

Section V - Service and Maintenance

This service manual is intended for use as a guide to technically qualified personnel when evaluating System

malfunctions. It is not to be construed as authorization to perform warranty repairs. Unauthorized service will void the

warranty.

Introduction

The Kendall SCD 700 series controller contains no user serviceable parts. User maintenance is covered in the sections

that follow. All other maintenance must be performed by technically qualified service personnel.

EN-17

Kendall SCD 700 Series

Service technicians should be familiar with the operator’s portion of this manual and the operating principles of the

Kendall SCD 700 series compression system. If a controller is to be returned to Covidien for service, a description of

the operating conditions and the fault code displayed should accompany the unit. The fault codes displayed by the

controller are useful in diagnosing service problems.

This manual describes service procedures to the circuit board level, with an exploded view of the controller shown

in Figure 9. If a component failure on a circuit board is suspected, the unit should be returned for service. It is

recommended that the system be returned with the circuit board in place, as removal of the board(s) involves

additional risk of mechanical damage and damage from electrostatic discharge (ESD).

Warranty and Factory Service

Covidien warrants that your Kendall SCD 700 series compression system is free from defective material and

workmanship. Our obligation under this warranty is limited to the repair of controllers returned to a service center,

transportation charges prepaid, within one year of delivery to the original purchaser. Specifically, we agree to

service and/or adjust any controller as required if returned for that purpose, and to replace and repair any part

which, upon our examination, is proven to have been defective. This warranty does not apply to the Tubing Set or

the disposable garments, or to equipment damaged through shipping, tampering, negligence, or misuse, including

liquid immersion, autoclaving, ETO sterilization, or the use of unapproved cleaning solutions. To the extent permitted

by applicable law, this limited warranty does not cover, and is intended to exclude, any and all liability on the part of

the Company, whether under this limited warranty or any warranty implied by law, for any indirect or consequential

damages for breach hereof or thereof. Except as expressly provided above in the limited warranty, to the extent

permitted by applicable law, the Company hereby negates and disclaims all express and to the extent permitted by

applicable law, implied warranties, including the warranties or merchantability and fitness for a particular purpose.

controllers requiring repairs should be sent to a service center. Call one of the service centers listed. Obtain a return

material authorization number and ship the controller, prepaid and insured in the original carton.

CANADA

Covidien Canada

7300 Trans Canada Highway

Pointe-Claire,QcH9R1C7

877-664-8926

UNITED STATES

Covidien

5920 Longbow Drive

Boulder CO 80301

1- (800) 962-9888

OUTSIDE U.S. AND CANADA

Covidien

Service Centre

Unit 2 Talisman Business Centre

London Road

Bicester, England OX26 6HR

(+44)1869328065

Disposal:

If the controller, tubing assembly and/or garment(s) is to be disposed of, follow the local country regulations

taking environmental factors into consideration.

Service Precautions:

• AlwaysunplugthecontrollerfromMainsvoltagebeforeservicingthecontroller.

• Usepropertechniquessuchasgroundingstrapsandpadstoprotectprintedcircuitboardassembliesfrom

ESD (Electrostatic Discharge).

Fan Filter, Exhaust Filter and Ventilation

CAUTION: Unplug the controller before accessing the fan filter or exhaust filter.

The fan filter and exhaust filter must be kept clean to ensure continued trouble-free operation. The controller

should never be run without the fan filter and exhaust filter in place. Clean or replace the filter when required. See

instructions in the General Disassembly/Reassembly Section.

During system use, obstruction of the fan cover and vents should be avoided. Free flow of air is necessary to prevent

overheating and premature component failure.

La pagina sta caricando ...

Covidien Kendall SCD 700 Series Operation And Service Manual

Marca: Covidien

Modello: Kendall SCD 700 Series

Tipo: Operation And Service Manual

Scarica il pdf

rapporto

in altre lingue

English: Covidien Kendall SCD 700 Series

Covidien Kendall SCD 700 Series Operation And Service Manual

Covidien Kendall SCD 700 Series Operation And Service Manual

in altre lingue

Altri documenti