Optika Italy B-150P Series Manuale utente

Model

B-150P-MRPL

B-150P-BRPL

B-150P Series

INSTRUCTION MANUAL

Ver. 5.0 2019

Page 2

1. Warning 3

2. Symbols and conventions 3

3. Safety Information 3

4. Intended use 3

5. Overview 4

5.1 B-150P-MRPL 4

5.2 B-150P-BRPL 5

6. Unpacking 6

7. Assembling 6

7.1 B-150P-MRPL 6

7.2 B-150P-BRPL 7

7.3 Assembling the microscope 8

8. Use of the microscope 9

8.1 Light intensity adjustment 9

8.2 Coarse focus tension adjustment 9

8.3 Stage 9

8.4 Adjust the interpupillary distance 9

8.5 Diopter adjustment 10

8.6 Aperture diaphragm 10

8.7 Use with rechargeable batteries 10

8.8 Useinbrighteld 11

8.9 Use in polarized light 11

9. Maintenance 12

10. Troubleshooting 13

Equipment disposal 14

Table of Contents

Page 3

1. Warning

This microscope is a scientic precision instrument designed to last for many years with a minimum of

maintenance. It is built to high optical and mechanical standards and to withstand daily use. We remind you

that this manual contains important information on safety and maintenance, and that it must therefore be made

accessible to the instrument users. We decline any responsibility deriving from incorrect instrument use uses

that does not comply with this manual.

2. Symbols and conventions

The following chart is an illustrated glossary of the symbols that are used in this manual.

CAUTION

This symbol indicates a potential risk and alerts you to proceed with caution.

ELECTRICAL SHOCK

This symbol indicates a risk of electrical shock.

3. Safety Information

Avoiding Electrical Shock

Before plugging in the power supply, make sure that the supplying voltage of your region matches with the ope-

ration voltage of the equipment and that the lamp switch is in o position. Users should observe all safety regu-

lations of the region. The equipment has acquired the CE safety label. However, users have full responsibility to

use this equipment safely. Please follow the guidelines below, and read this manual in its entirety to ensure safe

operation of the unit.

4. Intended use

Standard models

For research and teaching use only. Not intended for any animal or human therapeutic or diagnostic use.

IVD Models

Also for diagnostic use, aimed at obtaining information on the physiological or pathological situation of the

subject.

Page 4

5. Overview

COARSE

FOCUS KNOB

FINE FOCUS

KNOB

EYEPIECE

OBSERVATION

HEAD

MAIN SWITCH / INTENSITY

ADJUSTMENT DIAL

CONDENSER

STAGE

LED CHARGE

INDICATOR

NOSEPIECE

OBJECTIVES

TENSION

ADJUSTMENT

COLLAR

STAGE

CLIPS

POLARIZER

ANALYZER

5.1 B-150P-MRPL

Page 5

STAGE

CLIPS

5.2 B-150P-BRPL

LED CHARGE

INDICATOR

FINE FOCUS

KNOB

STAGE

OBSERVATION

HEAD

CONDENSER

OBJECTIVES

MAIN SWITCH / INTENSITY

ADJUSTMENT DIAL

NOSEPIECE

EYEPIECES

POLARIZER

ANALYZER

COARSE

FOCUS KNOB

TENSION

ADJUSTMENT

COLLAR

Page 6

6. Unpacking

The microscope is housed in a moulded Styrofoam container. Remove the tape from the edge

of the container and lift the top half of the container. Take some care to avoid that the opti-

cal items (objectives and eyepieces) fall out and get damaged. Using both hands (one around the

arm and one around the base), lift the microscope from the container and put it on a stable desk.

Do not touch with bare hands optical surfaces such as lenses, lters or glasses. Traces of grease or

other residuals may deteriorate the nal image quality and corrode the optics surface in a short time.

7. Assembling

Once opened the box, the microscope parts are the following:

7.1 B-150P-MRPL

① Frame

② Monocular observation head

③ Eyepiece

④ Tension adjustment tool

⑤ Objectives (4X / 10X / 40X)

⑥ Dust cover

⑦ Green lter

⑧ Power supply

③

④

⑤

⑥

⑦

⑧

①

②

Page 7

7.2 B-150P-BRPL

① Frame

② Monocular observation head

③ Eyepiece

④ Tension adjustment tool

⑤ Objectives (4X / 10X / 40X)

⑥ Dust cover

⑦ Green lter

⑧ Power supply

③

④

⑤

⑥

⑦

⑧

①

②

Page 8

7.3 Assembling the microscope

1. Remove the dust cap from the microscope frame

and from the bottom of the observation head.

2. Insert the optical head above the stand and

tighten the screw. (Fig. 1)

• Hold the head with one hand during the lo-

cking in order to avoid that the head falls.

3. Insert both eyepieces into the tubes of the optical

head. (Fig. 2)

• For model B-150P-MRPL: only one eye-

piece is used as this model is monocular.

4. Insert the power supply jack in the socket placed

at the rear side of the microscope. (Fig. 3)

Fig. 1

Fig. 2

Fig. 3

Page 9

8. Use of the microscope

Fig. 6

Fig. 4

①

Fig. 5

②

Fig. 7

③

④

⑤

8.1 Light intensity adjustment

Operate on the light intensity adjustment dial ① to

turn ON / OFF the microscope and to increase / de-

crease the illumination voltage. (Fig. 4)

8.2 Coarse focus tension adjustment

• Adjust the tension using the provided tool.

The tension of the coarse focusing knob is factory

preset.

1. To modify the tension according to personal’s

needs, rotate the ring

②

. (Fig. 5)

• Clockwise rotation increases the tension.

• If the tension is too loose, the stage could go

lower by itself or the focus easily lost after ne

adjustment. In this case, rotate the knob in order

to increase the tension

.

8.3 Stage

Stage is equipped with two clips ③ for the sample

placement.

Standard specimen is glass slide, thickness 1,2 mm

with coverslide 0,17mm. (Fig. 6)

Specimen can be moved with hands.

1. Lift the clip, place the specimen and gently relea-

se the clip until the specimen is secured over the

stage.(Fig. 6)

2. When used in polarized light stage can be ro-

tated on 360°, be grabbing the knurled ring

④ placed on the outer side of the stage.

8.4 Adjust the interpupillary distance

Only B-150P-BRPL

Hold the right and left parts of the observation head

using both hands and adjust the interpupillary distan-

ce by turning the two parts until one circle of light can

be seen. (Fig. 7)

• The graduation on the interpupillary distance in-

dicator ⑤, pointed by the spot “.” on the eyepiece

holder, shows the distance between the opera-

tor’s eyes.

The range of the interpupillary distance is 48- 75 mm.

Page 10

8.5 Diopter adjustment

Only B-150P-BRPL

1. Look into the right eyepiece with your right eye

only, and focus on the specimen.

2. Look into the left eyepiece with your left eye

only. If the image is not sharp, use the dioptric

adjustment ring ① to compensate. (Fig. 8)

• The adjustment range is ±5 diopter. The num-

ber indicated on the adjustment ring gradua-

tion should correspond to the operator’s dio-

ptric correction.

8.6 Aperture diaphragm

• The Numerical Aperture (N.A.) value of the aper-

ture diaphragm aects the image contrast. Incre-

asing or reducing this value one can vary reso-

lution, contrast and depth of focus of the image.

Move the diaphragm lever ② (Fig. 9) toward left

or right to decrease or increase the N.A. value.

• With low contrast specimens set the numerical

aperture to about 70%-80% of the objective’s

N.A. If necessary, remove on eyepiece and, lo-

oking into empty sleeve, adjust the condenser’s

diaphragm in order to obtain an image like the

one in Fig. 10

8.7 Use with rechargeable batteries

When the microscope is plugged with the power sup-

ply, the LED indicator for the battery recharge ③ is

lit. (Fig. 14)

• LED red: battery under charge

• LED green: battery fully charged.

When the microscope is unplugged, the LED is o.

During the normal use with batteries, LED is always

OFF.

Fig. 8

Fig. 9

②

Fig. 10

APERTURE

DIAPHRAGM

FIELD OF VIEW

30-20%

70-80%

Fig. 11

③

①

Page 11

8.8 Useinbrighteld

1. Move the analyzer slider ① to the right to remove

analyzer lter from the light path.(Fig. 12)

• In this way it is possible to work in brighteld.

8.9 Use in polarized light

1. Move the analyzer slider ① to the left to insert

analyzer lter into the light path.(Fig. 12)

2. Remove one eyepiece from the observation head.

3. Insert 10X objective into the light path.

4. Remove the specimen from the stage.

5. Rotate the polarizer lter ② (Fig. 13) until a com-

plete dark eld of view can be achieved. Now the

“crossed-Nicol” position is obtained and it is pos-

sible work in polarized light.

6. Put a specimen on the stage.

7. Insert the desired objective.

8. Focus the specimen.

9. Begin the observation.

• Polarizer can be removed from the light path sim-

ply rotating the polarizer unit toward right. (Fig.

14)

Fig. 12

①

Fig. 13

②

Fig. 14

Page 12

9. Maintenance

Microscopy environment

This microscope is recommended to be used in a clean, dry and shock free environment with a temperature of

5°-40°C and a maximum relative humidity of 85 % (non condensing). Use a dehumidier if needed.

To think about when and after using the microscope

• The microscope should always be kept vertically when moving it and be careful so that no

moving parts, such as the eyepieces, fall out.

• Never mishandle or impose unnecessary force on the microscope.

• Never attempt to service the microscope yourself.

• After use, turn o the light immediately, cover the microscope with the provided dust-cover,

and keep it in a dry and clean place.

Electrical safety precautions

• Before plugging in the power supply, make sure that the supplying voltage of your region

matches with the operation voltage of the equipment and that the lamp switch is in o-

position.

• Users should observe all safety regulations of the region. The equipment has acquired the

CE safety label. However, users do have full responsibility to use this equipment safely.

Cleaning the optics

• If the optical parts need to be cleaned try rst to: use compressed air.

• If that is not sucient: use a soft lint-free piece of cloth with water and a mild detergent.

• And as a nal option: use the piece of cloth moistened with a 3:7 mixture of ethanol and ether.

• Note: ethanol and ether are highly ammable liquids. Do not use them near a heat source, near

sparks or near electric equipment. Use these chemicals in a well ventilated room.

• Remember to never wipe the surface of any optical items with your hands. Fingerprints can damage the

optics.

• Do not disassemble objectives or eyepieces in attempt to clean them.

Forthebestresults,usetheOPTIKAcleaningkit(seecatalogue).

If you need to send the microscope to Optika for maintenance, please use the original packaging.

Page 13

10. Troubleshooting

Review the information in the table below to troubleshoot operating problems.

PROBLEM CAUSE SOLUTION

I. Optical Section:

LED operates, but eld of view remains

dark.

Power supply is unplugged. Connect

Brightness is too low Set brightness to a proper level

Batteries are uncharged Fully charge the batteries

Dirt or dust is visible in the eld of view. Dirt/dust on the specimen Clean the specimen

Dirt/dust on the eyepieces Clean the eyepieces

Image looks double Aperture diaphragm is stopped down

too far

Open aperture diaphragm

Visibility is poor.

• Image is not good.

• Contrast is poor.

• Details are indistinct.

• Image glares

Revolving nosepiece is in an incorrect

position

Move the nosepiece to a click stop

Aperture diaphragm is too closed or to

open

Adjust aperture diaphragm

Dust or dirt on lenses (condenser, ob-

jectives, eyepieces and slide)

Clean thoroughly

Polarizing filters are not in “crossed-

Nicol” position

Set them until “crossed-Nicol” position

can be achieved

One side of the image is out of focus. The nosepiece is not in the center of

the light path

Turn the nosepiece to a click stop

The specimen is out of place (tilted) Place the specimen at on the stage.

The optical performance of the sample

cover glass is poor

Use a cover glass of better quality

II. Mechanical Section:

The coarse focus knob is hard to turn. The tension adjustment collar is too

tight

Loosen the tension adjustment collar

The focus is unstable. The tension adjustment collar is too

loose

Tighten the tension adjustment collar

III. Electric section

The LED doesn’t turn on. No power supply Check the power cord connection

Batteries are uncharged Fully charge the batteries

The brightness is not enough The brightness adjustment is low Adjust the brightness

The light blinks The power cord is poorly connected Check the power cord

IV. Observation tube

Field of view of one eye does not match

that of the other.

Interpupillary distance is incorrect. Adjust interpupillary distance.

Incorrect diopter adjustment. Adjust diopter.

Your view is not accustomed to micro-

scope observation.

Upon looking into eyepieces, try look-

ing at overall field before concentrating

on specimen range. You may also find

it helpful to look up and into distance

for a moment before looking back into

microscope.

OPTIKA S.r.l.

Via Rigla, 30 - 24010 Ponteranica (BG) - ITALY Tel.: +39 035.571.392

info@optikamicroscopes.com - www.optikamicroscopes.com

OPTIKA

Spain

[email protected]

OPTIKA

USA

[email protected]

OPTIKA

China

[email protected]

OPTIKA

India

[email protected]

OPTIKA

Central America

[email protected]

®

Page 14

Equipment disposal

Art.13 Dlsg 25 July 2005 N°151. “According to directives 2002/95/EC, 2002/96/EC and 2003/108/EC relating

to the reduction in the use of hazardous substances in electrical and electronic equipment and waste disposal.”

The basket symbol on equipment or on its box indicates that the product at the end of its useful life should be

collected separately from other waste. The separate collection of this equipment at the end of its lifetime is or-

ganized and managed by the producer. The user will have to contact the manufacturer and follow the rules that

he adopted for end-of-life equipment collection. The collection of the equipment for recycling, treatment and

environmentally compatible disposal, helps to prevent possible adverse eects on the environment and health

and promotes reuse and/or recycling of materials of the equipment. Improper disposal of the product involves

the application of administrative penalties as provided by the laws in force.

OPTIKA S.r.l.

Via Rigla, 30 - 24010 Ponteranica (BG) - ITALY Tel.: +39 035.571.392

info@optikamicroscopes.com - www.optikamicroscopes.com

OPTIKA

Spain

[email protected]

OPTIKA

USA

[email protected]

OPTIKA

China

[email protected]

OPTIKA

India

[email protected]

OPTIKA

Central America

[email protected]

®

Modelli

B-150P-MRPL

B-150P-BRPL

Serie B-150P

MANUALE DI ISTRUZIONI

Ver. 5.0 2019

Pagina 17

1. Avvertenza 18

2. Simboli 18

3. Informazioni sulla sicurezza 18

4. Utilizzo previsto 18

5. Descrizione dello strumento 19

5.1 B-150P-MRPL 19

5.2 B-150P-BRPL 20

6. Disimballaggio 21

7. Assemblaggio 21

7.1 B-150P-MRPL 21

7.2 B-150P-BRPL 22

7.3 Procedura di assemblaggio 23

8. Uso del microscopio 24

8.1 Regolazione intensità luminosa 24

8.2 Regolazione della frizione 24

8.3 Tavolino 24

8.4 Regolazione distanza interpupillare 24

8.5 Regolazione diottrica 25

8.6 Diaframma di apertura 25

8.7 Uso con batterie ricaricabili 25

8.8 Uso in campo chiaro 26

8.9 Uso in luce polarizzata 26

9. Manutenzione 27

10. Risoluzione dei problemi 28

Smaltimento 29

Sommario

Pagina 18

1. Avvertenza

Questo microscopio è uno strumento scientico di alta precisione, progettato per durare a lungo con una minima

manutenzione; la realizzazione è secondo i migliori standard ottici e meccanici, per poter essere utilizzato

quotidianamente. Vi ricordiamo che questo manuale contiene informazioni importanti per la sicurezza e per la

manutenzione dello strumento, e deve quindi essere messo a disposizione di coloro che lo utilizzeranno.

Decliniamo ogni responsabilità derivante da un utilizzo dello strumento non indicato nel presente manuale.

2. Simboli

La seguente tabella riporta i simboli utilizzati in questo manuale.

PERICOLO

Questo simbolo indica un rischio potenziale ed avverte di procedere con cautela.

SHOCK ELETTRICO

Questo simbolo indica un rischio di shock elettrico.

3. Informazioni sulla sicurezza

Per evitare shock elettrici

Prima di collegare il cavo di alimentazione alla presa elettrica, assicurarsi che il voltaggio della rete locale

coincida con il voltaggio dello strumento e che l’interruttore dell’illuminazione sia nella posizione “OFF”.

Gli utenti dovranno seguire tutte le norme di sicurezza locali. Lo strumento è certicato CE. In ogni caso, gli

utilizzatori sono gli unici responsabili per un utilizzo sicuro dello strumento. Per l’utilizzo in sicurezza dello

strumento è importante attenersi alle seguenti istruzioni e leggere il manuale in tutte le sue parti.

4. Utilizzo previsto

Modelli standard

Solo per applicazioni di ricerca ed usi didattici. Non indicato per utilizzo diagnostico e terapeutico umano e ve-

terinario.

Modelli IVD

Anche per uso diagnostico, nalizzato ad ottenere informazioni sulla situazione siologica o patologica del sog-

getto.

Pagina 19

5. Descrizione dello strumento

MANOPOLA

MACROMETRICA DI

MESSA A FUOCO

MANOPOLA

MICROMETRICA DI

MESSA A FUOCO

OCULARE

TESTA DI

OSSERVAZIONE

INTERRUTTORE / ROTELLA

REGOLAZIONE INTENSITÀ

CONDENSATORE

TAVOLINO

LED INDICATORE DI

CARICA

REVOLVER

OBIETTIVI

ANELLO

REGOLAZIONE

TENSIONE

MOLLETTINE

FERMACAMPIONE

POLARIZZATORE

ANALIZZATORE

5.1 B-150P-MRPL

Pagina 20

5.2 B-150P-BRPL

MOLLETTINE

FERMACAMPIONE

LED

INDICATORE DI

CARICA

MANOPOLA

MICROMETRICA DI

MESSA A FUOCO

TAVOLINO

TESTA DI

OSSERVAZIONE

CONDENSATORE

OBIETTIVI

INTERRUTTORE / ROTELLA

REGOLAZIONE INTENSITÀ

REVOLVER

OCULARI

POLARIZZATORE

ANALIZZATORE

MANOPOLA

MACROMETRICA DI

MESSA A FUOCO

ANELLO

REGOLAZIONE

TENSIONE

La pagina sta caricando ...

Optika Italy B-150P Series Manuale utente

Questo manuale è adatto anche per

Optika Italy B-150P Series Manuale utente

in altre lingue

Altri documenti