Belkin TUNECAST 3 #F8M010EA Manuale del proprietario

Tipo
Manuale del proprietario
| 0AIntroduction
EN
FR
DE
ES
IT
User Manual
TuneCast
®
3 Mobile FM Transmitter
EN
FR
DE
ES
IT
Introduction
EN
User Manual
TuneCast
®
3 Mobile FM Transmitter
EN
Introduction
Congratulations and thank you for purchasing the TuneCast 3 Mobile FM Transmitter
from Belkin. This product is designed to play your portable audio device through your
car, home, or portable stereo. Please review this User Manual carefully so that you can be
sure to get the most from your TuneCast 3, virtually anywhere you go.
Introduction | 01
Stereo/Mono
ON/OFF
Forward/
Back
3.5mm Cable
Preset 1
Preset 2
EN
Operating Instructions
Operating Instructions | 02
Using the TuneCast 3 Mobile FM Transmitter
1. Turn down your car stereo’s volume.
2. Tune your stereo frequency to a channel with a weak broadcast signal. The ideal channel
is one that is not broadcasting a radio program, or is doing so weakly.
3. Connect the TuneCast 3 to your portable audio device.
4. Connect the included Auto Power Cord to your cigarette-lighter outlet in your car and to
the bottom of your TuneCast 3 for optional powering in the car.
5. Press and hold the ON/OFF button for approximately two seconds. The display’s status
bar will indicate when the device is powered on.
6. Press the ”
” or ” button on the TuneCast 3 to match the frequency on the radio
chosen in step 2. Pressing and holding either button will provide faster tuning.
7. Adjust the volume on the audio device to about three-fourths of the maximum.
Adjust the volume of your FM radio to the desired listening level.
Memory Preset
Frequency
Power Source
Battery or DC Power
Stereo/Mono
Operating Instructions
Operating Instructions | 03
Storing and Using Presets
1. To store a preset, select the desired frequency using or buttons. Press
and hold the desired preset button (
1 or 2) for two seconds (the status bar will give
you visible feedback). An audible beep sounds in the transmitted audio when the
new frequency is programmed. The TuneCast 3 display reflects the change when the
memory button is released by showing which memory button was pressed along
with the frequency saved in that memory position.
2. To select one of your preset frequencies, momentarily press “1” or “2”. This will
instantly tune the TuneCast 3 to the frequency stored in that preset.
NOTE: Storing a preset will memorize the frequency as well as the current mono/stereo setting.
Memory Presets
Stored Preset
EN
Stereo/Mono Selection
Transmitting music in stereo generally gives you the highest-quality listening
experience. However, you may get better FM-signal reception by changing the
transmission to mono. The TuneCast 3 transmits in stereo mode by default. We suggest
that you switch from stereo to mono transmission only if your car stereo is NOT receiving
a clear signal from the TuneCast 3, or if you are listening to mono recordings such as
audio books.
Press and hold the “Mono/Stereo” button located on the upper-left corner of the
TuneCast 3. The status-bar indicator will transition from stereo to mono or vice versa.
The TuneCast 3 display will return to normal operation where the current frequency is
shown along with the current mono or stereo setting represented by:
Mono/Stereo Button
Mono/Stereo Display
Operating Instructions | 04
Operating Instructions
Operating Instructions | 05
Adjusting and Locking the Cable
The cable length of the TuneCast 3 can be changed and locked for different applications.
Operating Instructions
EN
Operating Instructions
Operating Instructions
| 06
Mounting
Use the cradle and mount with adhesive backing to attach your TuneCast 3
to any smooth surface.
Operating Instructions | 07
Operating Instructions
Changing the Batteries
Gently push the battery door on the back of the unit downward. Replace batteries.
Position cover on back by gently sliding it up until it locks in position.
Important TuneCast 3 Battery-Operation Details
TuneCast 3 automatically extends battery life and helps ensure safe operation in these ways:
1. TuneCast 3 turns off after approximately 60 seconds without audio detection. We
recommend that you manually turn off the TuneCast 3 when not using it, to limit
unnecessary battery use.
2. When plugged into your vehicle’s power outlet, TuneCast 3 automatically switches from
battery to DC power.
3. TuneCast 3 displays the battery-life status and turns itself off when the batteries no
longer contain enough power to operate. This prevents a potentially hazardous over-
discharge condition.
EN
Troubleshooting
Troubleshooting
| 08
Issue
The audio is distorted.
Solution 1 Decrease the volume of your audio device until you no longer hear distortion. Keeping the device’s
volume level at or below three-fourths of the maximum should prevent audio distortion. However, don’t turn it
so low that the audio-detection circuit shuts down your TuneCast 3.
Solution 2 Tune your car stereo and the TuneCast 3 to a different frequency.
Issue
TuneCast 3 automatically turns off when I am playing music.
Solution Turn up your music-player volume. If the audio-detection circuit does not detect audio for 10 minutes, it
shuts down the unit to preserve the battery. Possible causes of this s
ituation are having the music-player volume too low or pausing the player for longer
than 10 minutes.
Issue
The battery indicator does not seem to display the correct battery status.
Solution Be sure to use non-rechargeable alkaline batteries. Other battery types can cause TuneCast 3 to display
incorrect battery life.
Issue
My TuneCast 3 automatically powers off when I turn off my vehicle or unplug the unit from my car’s
power outlet.
Solution TuneCast 3 automatically turns off when external DC power is removed.
Issue
I am unable to get clear FM reception.
Solution 1 Tune your car stereo and the TuneCast 3 to a different frequency.
Solution 2
In some instances, lowering the car antenna (in cars where available) improves the clarity of the TuneCast
3 signal.
Solution 3 Change the stereo/mono setting to mono mode. This may improve signal reception, but the audio
will be monaural instead of stereo.
Solution 4 If used indoors, attach or reposition the antennae on the stereo receiver.
Issue
TuneCast 3 does not appear to be saving my settings.
Solution Be sure NOT to release the button until the audible beep occurs or the status bar indicator is
complete. Your settings are stored in memory when the TuneCast 3 display returns to normal operation.
Free tech Support | 09
Free Tech Support*
You can find additional support information on our website www.belkin.com through
the tech-support area. If you want to contact technical support by phone, please call the
number you need from the list below*.
*Local rates apply
Country Number Internet adress
AUSTRIA 08 - 20 20 07 66 http://www.belkin.com/uk
BELGIUM 07 07 00 073 http://www.belkin.com/nl
CZECH REPUBLIC 23 900 04 06 http://www.belkin.com/uk
DENMARK 701 22 403 http://www.belkin.com/uk
FINLAND 00800 - 22 35 54 60 http://www.belkin.com/uk
FRANCE 08 - 25 54 00 26 http://www.belkin.com/fr
GERMANY 0180 - 500 57 09 http://www.belkin.com/de
GREECE 00800 - 44 14 23 90 http://www.belkin.com/uk
HUNGARY 06 - 17 77 49 06 http://www.belkin.com/uk
ICELAND 800 8534 http://www.belkin.com/uk
IRELAND 0818 55 50 06 http://www.belkin.com/uk
ITALY 02 - 69 43 02 51 http://www.belkin.com/it/support/tech
LUXEMBOURG 34 20 80 8560 http://www.belkin.com/uk
NETHERLANDS
0900 - 040 07 90
0.10 per minute
http://www.belkin.com/nl
NORWAY 815 00 287 http://www.belkin.com/uk
POLAND 00800 - 441 17 37 http://www.belkin.com/uk
PORTUGAL 707 200 676 http://www.belkin.com/uk
RUSSIA 495 580 9541 http://www.belkin.com/uk
SOUTH AFRICA 0800 - 99 15 21 http://www.belkin.com/uk
SPAIN 902 - 02 43 66 http://www.belkin.com/es/support/tech
SWEDEN 07 - 71 40 04 53 http://www.belkin.com/se/support/tech
SWITZERLAND 08 - 48 00 02 19 http://www.belkin.com/uk
UNITED KINGDOM 0845 - 607 77 87 http://www.belkin.com/uk
OTHER COUNTRIES +44 - 1933 35 20 00
EN
Information | 10
Electrical/Environmental Specifications
Power Requirement: 2x AAA batteries, or 5.5V, 75mA at CLA input
Operating Temperature: 0° C to 45° C
Expected Continuous Run Time: 20 hours on new, 1175mAh alkaline batteries
Storage Precautions – When storing the TuneCast 3 for extended periods of time, Belkin recommends
the following:
1) Remove the batteries.
2) Keep out of direct sunlight and fluorescent lamps.
3) Avoid low (below C) and high (greater than 35° C) temperature environments.
4) Avoid high humidity environments.
European Standards Compliance Statement
This product complies with the following standards: EN 60065, EN 300 320 and EN 301 489. For the full Declaration of
Conformity please follow the following link:
www.belkin.com/doc
This product complies to the WEEE directive. For recycling information please follow the following link:
www.belkin.com/environmental
Information
0673
Warranty | 11
What this warranty covers.
Belkin International, Inc. warrants to the original purchaser of this Belkin product that the product shall
be free of defects in design, assembly, material, or workmanship.
What the period of coverage is.
Belkin International, Inc. warrants the Belkin product for three years.
What will we do to correct problems?
Product Warranty.
Belkin will repair or replace, at its option, any defective product free of charge (except for shipping
charges for the product).
What is not covered by this warranty?
All above warranties are null and void if the Belkin product is not provided to Belkin International, Inc.
for inspection upon Belkin’s request at the sole expense of the purchaser, or if Belkin International, Inc.
determines that the Belkin product has been improperly installed, altered in any way, or tampered with.
The Belkin Product Warranty does not protect against acts of God (other than lightning) such as flood,
earthquake, war, vandalism, theft, normal-use wear and tear, erosion, depletion, obsolescence, abuse,
damage due to low voltage disturbances (i.e. brownouts or sags), non-authorized program, or system
equipment modification or alteration.
How to get service.
To get service for your Belkin product you must take the following steps:
1. Contact Belkin Customer Service (see details on page 9), within 15 days of the Occurrence.
Be prepared to provide the following information:
a. The part number of the Belkin product.
b. Where you purchased the product.
c. When you purchased the product.
d. Copy of original receipt.
2. Your Belkin Customer Service Representative will then instruct you on how to forward your receipt
and Belkin product and how to proceed with your claim.
Belkin International, Inc. Limited 3-Year Product Warranty
EN
Warranty | 12
Belkin International, Inc. Limited 3-Year Product Warranty
Belkin International, Inc. reserves the right to review the damaged Belkin product. All costs of shipping
the Belkin product to Belkin International, Inc. for inspection shall be borne solely by the purchaser.
If Belkin determines, in its sole discretion, that it is impractical to ship the damaged equipment to
Belkin International, Inc., Belkin may designate, in its sole discretion, an equipment repair facility to
inspect and estimate the cost to repair such equipment. The cost, if any, of shipping the equipment
to and from such repair facility and of such estimate shall be borne solely by the purchaser. Damaged
equipment must remain available for inspection until the claim is finalized. Whenever claims are settled,
Belkin International, Inc. reserves the right to be subrogated under any existing insurance policies the
purchaser may have.
How state law relates to the warranty.
THIS WARRANTY CONTAINS THE SOLE WARRANTY OF Belkin International, Inc., THERE ARE NO OTHER
WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED BY LAW, IMPLIED, INCLUDING THE IMPLIED
WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
AND SUCH IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above
limitations may not apply to you.
IN NO EVENT SHALL Belkin International, Inc. BE LIABLE FOR INCIDENTAL, SPECIAL, DIRECT, INDIRECT,
CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS, BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS
ARISING OUT OF THE SALE OR USE OF ANY BELKIN PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
This warranty gives you specific legal rights, and you may also have other rights, which may vary from
state to state. Some states do not allow the exclusion or limitation of incidental, consequential, or other
damages, so the above limitations may not apply to you.
Belkin Tech Support
US: 310-898-1100 ext. 2263
800-223-5546 ext. 2263
Europe: 00 800 223 55 460
Australia: 1800 235 546
New Zealand: 0800 235 546
Singapore: 800 616 1790
Belkin International, Inc.
501 West Walnut Street
Los Angeles, CA 90220, USA
310-898-1100
310-898-1111 fax
Belkin Ltd.
Express Business Park, Shipton Way
Rushden, NN10 6GL, United Kingdom
+44 (0) 1933 35 2000
+44 (0) 1933 31 2000 fax
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk, The Netherlands
+31 (0) 20 654 7300
+31 (0) 20 654 7349 fax
Belkin Ltd.
4 Pioneer Avenue
Tuggerah Business Park
Tuggerah, NSW 2259, Australia
+61 (0) 2 4350 4600
+61 (0) 2 4350 4700 fax
© 2006 Belkin International, Inc.. All rights reserved.
All trade names are registered trademarks of respective manufacturers listed.
F8M010ea P75185ea
Introduction
FR
Mode d’emploi
Émetteur FM TuneCast
®
3
Introduction
Félicitations et merci d’avoir choisi l’Émetteur FM TuneCast 3 de Belkin. Ce produit est
conçu pour faire jouer votre iPod via votre autoradio et votre chaîne Hi-fi de salon ou
portative. Veuillez prendre connaissance de la totalité de ce manuel, afin de tirer le
meilleur de votre TuneCast 3, où que vous soyez.
Introduction | 01
Stéo/mono
ON/OFF
Suivant/
Prédent
Câble 3,5 mm
moire 1
moire 2
Mode d’emploi
Mode d’emploi | 02
Utilisation de l’Émetteur FM TuneCast® 3
1. Baissez le son de votre autoradio.
2. Syntonisez une fréquence radio diffusant un signal faible. Le canal idéal est celui qui
n’émet pas de programme radio ou qui le fait très faiblement.
3. Branchez le TuneCast 3 à votre appareil audio portatif.
4. Branchez le cordon d’alimentation pour la voiture à l’allume-cigare de votre voiture et au
bas du TuneCast pour l’alimentation dans la voiture (facultatif).
5. Appuyez sur le bouton ON/OFF et maintenez-le enfoncé pendant environ deux
secondes. La barre d’état de l’écran indique que l’appareil est alimenté.
6. Appuyez sur le bouton «
» ou le bouton « » du TuneCast 3 pour syntoniser la
fréquence radio choisie à l’étape 2. Appuyer sur le bouton et le maintenir enfoncé permet
de syntoniser plus rapidement.
7. Réglez le volume de l’appareil audio à environ le trois quarts du maximum. Réglez le
volume de votre radio FM au niveau d’écoute souhaité.
moire
Fréquence
Source d’alimentation
Pile ou courant CC
Stéo/mono
FR
Mode d’emploi
Mode d’emploi | 03
Utilisation de la mémoire
1. Pour stocker une fréquence en mémoire, lectionnez la fréquence désie au
moyen des boutons « » ou « ». Appuyez sur le bouton de mémoire siré (
1
ou
2) et maintenez-le enfonpendant deux secondes (la barre d’état émettra un
signal visuel). Un bip se fait entendre à travers l’audio lorsque la nouvelle fréquence
est programmée. Lécran du TuneCast3 affiche le changement lorsque le bouton
de mémoire est relâché, en montrant le bouton de mémoire sur lequel vous avez
appuyé, ainsi que la fquence enregistrée.
2. Pour lectionner l’une ou l’autre des fréquences programes, appuyez sur « 1 »
ou «
2 ». Lémetteur TuneCast 3 syntonise automatiquement la fquence enregistrée
dans la moire.
REMARQUE : Lors de l’enregistrement, l’unienregistre le réglage mono/stéo, en plus de la
fréquence.
moires
Fréquence
enregiste
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74

Belkin TUNECAST 3 #F8M010EA Manuale del proprietario

Tipo
Manuale del proprietario