Ubiquiti ES-24-250W Guida Rapida

Marca: Ubiquiti

Modello: ES-24-250W

Categoria: Convertitori multimediali di rete

Tipo: Guida Rapida

Questo manuale è adatto anche per

ES-24-500W

Managed PoE+ Gigabit Switch

with SFP

Models: ES-24-250W, ES-24-500W

Introduction

Thank you for purchasing the Ubiquiti Networks® EdgeSwitch

™

This Quick Start Guide is designed to guide you through the

installation and show you how to access the Configuration

Interface. This Quick Start Guide also includes the warranty

terms, and is for use with the EdgeSwitch, modelES‑24‑250W

or ES‑24‑500W. (The hardware description and installation

instructions are the same for both models.)

Package Contents

24V

EdgeSwitch

Managed PoE+ Gigabit Switch

with SFP

Models: ES-24-250W, ES-24-500W

Power Cord Mounting Screws

(#10‑32 x 5/8", Qty. 4)

Cage Nuts

(#10‑32 x 5/8", Qty. 4)

Quick Start

Guide

responsibility to follow local country regulations, including operation within legal frequency

channels, output power, indoor cabling requirements, and Dynamic Frequency Selection

(DFS) requirements.

Installation Requirements

• Phillips screwdriver

• Standard‑sized, 19" wide rack with a minimum of 1U height

available

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your outdoor networks

from the most brutal environments and devastating ESD

attacks with industrial‑grade shielded Ethernet cable,

TOUGHCable

™

, from Ubiquiti Networks. For more details,

visit: www.ubnt.com/toughcable

Note: Although the cabling can be located outdoors,

the EdgeSwitch itself should be housed inside a

protective enclosure.

Hardware Overview

Front Panel LEDs

System

RJ45: PoE

RJ45: Speed/Link/Act

SFP: Speed/Link/Act

LED State Status

System

White Ready for Use

Blue

Bootup in Progress

Flashing Indicates Reset

to Factory Defaults

RJ45 1‑24

PoE

Off No PoE

Amber IEEE 802.3af/802.3at

Green 24V Passive

Speed/

Link/

Act

Off No Link

Amber

Link Established at

10/100Mbps

Flashing Indicates Activity

Green

Link Established at

1000Mbps

Flashing Indicates Activity

SFP 1‑2

Speed/

Link/

Act

Off No Link

Green

Link Established at 1Gbps

Flashing Indicates Activity

Front Panel Button

Reset

Button Description

Reset

There are two methods to reset the

EdgeSwitch to factory defaults:

Runtime Reset (Recommended)

The EdgeSwitch should be running after

bootup is complete, and the System LED

is white. Press and hold the Reset button.

The EdgeSwitch will reboot, and the System

LED becomesblue after three seconds.

Continue to hold the Reset button for

about 15seconds until the System LED

flashes blue for two seconds. This indicates

that the EdgeSwitch has reset to its

factorydefaults.

Power‑on Reset

1. Disconnect the Power Cord from the

EdgeSwitch.

2. While connecting the Power Cord to

the EdgeSwitch, hold the Reset button

for about 15seconds until the System

LED flashes blue for two seconds. This

indicates that the EdgeSwitch has reset

to its factory defaults.

Front Panel Ports

RJ45 1-24

SFP 1-2

Interface Description

RJ45 1‑24

RJ45 ports support Power over Ethernet

(PoE) and 10/100/1000 Ethernet connections.

SFP 1‑2

Hot‑swappable SFP ports support 1 Gbps

connections.

Back Panel

Mounting Holes

Power

Mounting Holes

Side Panels

Ventilation Holes

Fans

*640-00102-04*

640-00102-04

Hardware Installation

1. Connect the Power Cord to the Power port of the

EdgeSwitch.

2. Attach the EdgeSwitch to the rack using the four Mounting

Screws. (If the rack has square slots, then use the Cage Nuts

with the Mounting Screws.)

Note: Keep 20 mm of clearance next to the

ventilation holes for adequate airflow.

3. Connect the other end of the Power Cord to a power outlet.

Connecting Ethernet

1. Connect an Ethernet cable from your computer or host

system to any port of the EdgeSwitch.

2. Connect Ethernet cables from the Ethernet ports of your

devices to the numbered ports of the EdgeSwitch.

Note: The PoE settings for ports 1-24 are set to

PoE+auto by default, so 802.3af/at devices can

be plugged in and automatically receive PoE. For

instructions on how to enable 24V passive PoE,

refer to the Configuring PoE Settings section on the

backpage.

Using SFP Ports

To use an SFP port:

1. Remove the protective plug covering the SFP port.

2. Plug a compatible fiber module into the SFP port.

1000Mbps SM/SC 20KM DDM

Tx1550nm/Rx1310nm

3. Connect the fiber optic cable to the fiber module. Then

connect the other end of the cable to another fiber device.

For information about compatible fiber SFP modules, visit:

community.ubnt.com/edgemax

Accessing the Configuration Interface

The EdgeSwitch is set to DHCP by default, so it will try to

automatically obtain an IP address. If that fails, then it will use

the default fallback IP address, 192.168.1.2. Proceed to the

appropriate section, DHCP or Fallback IP Address:

DHCP

Use one of the following methods:

• Set up the DHCP server to provide a specific IP address to

the EdgeSwitch based on its MAC address (on the label).

• Let the EdgeSwitch obtain an IP address and then check the

DHCP server to see which IP address was assigned.

To log in, follow these steps:

1. Launch your web browser. Type the appropriate IP address

in the address field. Press enter (PC) or return (Mac).

2. The login screen will appear. Enter ubnt in the Username

and Password fields. Read the Ubiquiti License Agreement,

and check the box next to I agree to the terms of this License

Agreement to accept it. Click Login.

The EdgeSwitch Configuration Interface will appear. Customize

additional settings as needed. For more information on PoE

configuration, refer to the Configuring PoE Settings section on

the back page.

Fallback IP Address

1. Ensure that your computer (or other host machine) is

connected to the EdgeSwitch.

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet.

3. Launch your web browser. Type the appropriate IP address

in the address field (192.168.1.2 is the default fallback IP

address). Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Read the Ubiquiti License Agreement,

and check the box next to I agree to the terms of this License

Agreement to accept it. Click Login.

5. The EdgeSwitch Configuration Interface will appear. Go to

System > Connectivity > IPv4.

6. Change the IP Address to a unique IP address or select

DHCP on the IPv4 tab. Click Submit.

Note: If you change the IP settings, then the session

will be cut off, and you will need to reconnect to the

EdgeSwitch using the new IP address.

Customize additional settings as needed. For more information

on PoE configuration, refer to the Configuring PoE Settings

section on the back page.

Configuring PoE Settings

The PoE settings for ports 1-24 are set to PoE+ auto by default,

so 802.3af/at devices can be plugged in and automatically

receive PoE.

WARNING: Before activating 24V passive PoE, ensure

that the connected device supports PoE and the

suppliedvoltage.

1. Go to PoE > PoE Configuration.

2. Select the Ethernet port you want to configure. Then

clickEdit.

3. Select the appropriate mode: Off, PoE+ auto, or

24Vpassive from the PoE Mode drop‑down menu.

ThenclickSubmit.

For more information, refer to the EdgeSwitch documentation,

which is available at documentation.ubnt.com/edgemax

Specifications

EdgeSwitch

Dimensions

485.04 x 44.45 x 285.6 mm (19.1 x 1.75 x 11.24")

Weight

ES‑24‑250W

ES‑24‑500W

4.7 kg (10.4 lb)

4.8 kg (10.6 lb)

Total Non‑Blocking Line Rate

26 Gbps

Max. Power Consumption

ES‑24‑250W

ES‑24‑500W

250W

500W

Power Method 100‑240VAC/50‑60 Hz, Universal Input

Power Supply

ES‑24‑250W

ES‑24‑500W

AC/DC, Internal, 250W DC

AC/DC, Internal, 500W DC

Certications CE, FCC, IC

Rack‑Mount Yes, 1U High

ESD/EMP Protection Air: ± 24 kV, Contact: ± 24 kV

Operating Temperature ‑5 to 40° C (23 to 104° F)

Operating Humidity 5 to 95% Noncondensing

Shock and Vibration ETSI300‑019‑1.4 Standard

LEDs Per Port

RJ45 Data Ports PoE, Speed/Link/Activity

SFP Data Ports Speed/Link/Activity

Interfaces

Networking Interfaces (24) 10/100/1000 Mbps RJ45 Ethernet Ports

(2) 1 Gbps SFP Ethernet Ports

Management Interface Ethernet In/Out Band

PoE Per Port

PoE Interfaces

POE+ IEEE 802.3af/at (Pins 1, 2+; 3, 6‑)

24VDC Passive PoE (Pins 4, 5+; 7, 8‑)

Max. PoE+ Wattage per

Port by PSE

34.2W

Voltage Range 802.3at

Mode

50–57V

Max. Passive PoE Wattage

per Port

17W

24V Passive PoE Voltage

Range

20‑27V

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2‑wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short‑circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal physical,

electromagnetic or electrical stress, including lightning strikes, or

accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,

SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM

AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,

EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,

REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,

ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,

SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS

FOR A PARTICULAR PURPOSE AND NON‑INFRINGEMENT AND ANY

WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.

BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR

ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE

TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS

AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS

FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD

PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT

CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY

OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant

that the operation of the Products will be error‑free or that operation will

be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING

OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE

PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER

LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you.

You may have other rights that vary from country to country, state to

state, or province to province. Some countries, states and provinces do not

allow the exclusion or limitation of liability for incidental or consequential

damages, so the above limitation may not apply to you. EXCEPT TO

THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO

NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE

MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY

SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not apply

to any transactions regarding the sale of the Products.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operations of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

Industry Canada

This Class A digital apparatus complies with Canadian CAN ICES‑3(B).

Cet appareil numérique de la classe A est conforme à la norme NMB‑3(B)

Canada.

Australia and New Zealand

Warning: This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may

be required to take adequate measures.

CE Marking

CE marking on this product represents the product is in compliance with all

directives that are applicable to it.

RoHS/WEEE Compliance Statement

English

European Directive 2002/96/EC requires that the equipment bearing

this symbol on the product and/or its packaging must not be disposed

of with unsorted municipal waste. The symbol indicates that this

product should be disposed of separately from regular household waste

streams. It is your responsibility to dispose of this and other electric and

electronic equipment via designated collection facilities appointed by the

government or local authorities. Correct disposal and recycling will help

prevent potential negative consequences to the environment and human

health. For more detailed information about the disposal of your old

equipment, please contact your local authorities, waste disposal service, or

the shop where you purchased the product.

Deutsch

Die Europäische Richtlinie 2002/96/EC verlangt, dass technische

Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem

Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall

entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt

von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es

liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische

und elektronische Geräte über die dafür zuständigen und von der

Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu

entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,

potentielle negative Folgen für Umwelt und die menschliche Gesundheit

zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer

Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder

städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das

Produkt erworben haben.

La pagina sta caricando ...

Ubiquiti ES-24-250W Guida Rapida

Marca: Ubiquiti

Modello: ES-24-250W

Categoria: Convertitori multimediali di rete

Tipo: Guida Rapida

Questo manuale è adatto anche per

ES-24-500W

Scarica il pdf

rapporto

in altre lingue

English: Ubiquiti ES-24-250W Quick start guide
română: Ubiquiti ES-24-250W Ghid de inițiere rapidă

Ubiquiti ES-24-250W Guida Rapida

Questo manuale è adatto anche per

Ubiquiti ES-24-250W Guida Rapida

in altre lingue

Documenti correlati