Garmin GPSMAP 7407 Manuale del proprietario

Tipo
Manuale del proprietario
GPSMAP
®
7400/7600
Series
Installation Instructions
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
To obtain the best performance and to avoid damage to your
boat, install the device according to these instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin
®
Product Support.
Registering Your Device
Help us better support you by completing our online registration
today.
Go to my.garmin.com.
Keep the original sales receipt, or a photocopy, in a safe
place.
Contacting Garmin Support
Go to support.garmin.com for help and information, such as
product manuals, frequently asked questions, videos, and
customer support.
In the USA, call 913-397-8200 or 1-800-800-1020.
In the UK, call 0808 238 0000.
In Europe, call +44 (0) 870 850 1241.
Software Update
You may need to update the device software when you install
the device or add an accessory to the device.
This device supports up to a 32 GB memory card, formatted to
FAT32.
Loading the New Software on a Memory Card
1
Insert a memory card into the card slot on the computer.
2
Go to www.garmin.com/support/software/marine.html.
3
Select Download next to GPSMAP Series with SD Card.
4
Read and agree to the terms.
5
Select Download.
6
Select Run.
7
Select the drive associated with the memory card, and select
Next > Finish.
Updating the Device Software
Before you can update the software, you must obtain a
software-update memory card or load the latest software onto a
memory card.
1
Turn on the chartplotter.
2
After the home screen appears, insert the memory card into
the card slot.
NOTE: In order for the software update instructions to
appear, the device must be fully booted before the card is
inserted.
3
Follow the on-screen instructions.
4
Wait several minutes while the software update process
completes.
5
When prompted, leave the memory card in place and restart
the chartplotter manually.
6
Remove the memory card.
NOTE: If the memory card is removed before the device
restarts fully, the software update is not complete.
Tools Needed
Drill and drill bits
Bail mount: drill bits appropriate for the surface and
hardware
Flush mount: 13 mm (
1
/
2
in.) drill bit, 7.2 mm (
5
/
16
in.), and
3.5 mm (
1
/
8
in.) drill bit
#2 Phillips screwdriver
Jigsaw or rotary tool
File and sandpaper
Marine sealant (recommended)
Mounting Considerations
NOTICE
This device should be mounted in a location that is not exposed
to extreme temperatures or conditions. The temperature range
for this device is listed in the product specifications. Extended
exposure to temperatures exceeding the specified temperature
range, in storage or operating conditions, may cause device
failure. Extreme-temperature-induced damage and related
consequences are not covered by the warranty.
When selecting a mounting location, you should observe these
considerations.
The location should provide optimal viewing as you operate
your boat.
The location should allow for easy access to all device
interfaces, such as the keypad, touchscreen, and card
reader, if applicable.
The location must be strong enough to support the weight of
the device and protect it from excessive vibration or shock.
To avoid interference with a magnetic compass, the device
should not be installed closer to a compass than the
compass-safe distance value listed in the product
specifications.
The location must allow room for the routing and connection
of all cables.
January 2017
Printed in Taiwan 190-02071-02_0C
The location must not be a flat, horizontal surface. The
location should be in a vertical angle.
The location and viewing angle should be tested before you
install the device. High viewing angles from above and below
the display may result in a poor image.
Bail Mounting the Device
NOTICE
If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid cracking in the gel-coat layer when the screws are
tightened.
The bail-mounting hardware (screws and washers, or nuts,
washers, and bolts) is not included. The bail mount bracket is
included in some models. Before you can bail mount the device,
you must purchase a bail mount bracket, if necessary. You must
also purchase mounting hardware that fits the holes in the bail
mount bracket and securely attaches it to your specific mounting
surface. The size of the pilot holes required depends on the
mounting hardware you purchase.
1
Using the bail mount bracket
À
as a template, mark the
location of the four pilot holes
Á
.
2
Using a drill bit appropriate for your mounting hardware, drill
the pilot holes.
3
Secure the bail mount bracket to the surface using your
mounting hardware
Â
.
4
Install the bail mount knobs
Ã
on the sides of the device.
5
Place the device in the bail mount bracket, and tighten the
bail mount knobs.
Flush Mounting the Device
NOTICE
Be careful when cutting the hole to flush mount the device.
There is only a small amount of clearance between the case and
the mounting holes, and cutting the hole too large could
compromise the stability of the device after it is mounted.
The included template and hardware can be used to flush mount
the device in your dashboard.
1
Trim the template, and make sure it fits in the location where
you want to mount the device.
2
Secure the template to the selected location.
3
Using a 13 mm (
1
/
2
in.) drill bit, drill one or more of the holes
inside the corners of the solid line on the template to prepare
the mounting surface for cutting.
4
Using a jigsaw or a rotary tool, cut the mounting surface
along the inside line on the template.
5
Place the device in the cutout to test the fit.
6
If necessary, use a file and sandpaper to refine the size of
the cutout.
7
After the device fits correctly in the cutout, ensure the
mounting holes on the device line up with the larger 7.2 mm
(
5
/
16
in.) holes on the template.
8
If the mounting holes on the device do not line up, mark the
new hole locations.
9
Using a 7.2 mm (
5
/
16
in.) drill bit, drill the larger holes.
10
Starting in one corner of the template, place a nut plate
À
over the larger hole
Á
drilled in step 9.
The smaller 3.5 mm (
1
/
8
in.) hole
Â
on the nut plate should
line up with the smaller hole on the template.
11
If the smaller 3.5 mm (
1
/
8
in.) hole on the nut plate does not
line up with the smaller hole on the template, mark the new
hole location.
12
Repeat steps 10 and 11 to verify placement of the remaining
nut plates and holes on the template.
13
Using a 3.5 mm (
1
/
8
in.) drill bit, drill the smaller holes.
14
Remove the template from the mounting surface.
15
Starting in one corner of the mounting location, place a nut
plate
Ã
on the back of the mounting surface, lining up the
large and small holes.
The raised portion of the nut plate should fit into the larger
hole.
16
Secure the nut plate to the mounting surface by fastening an
included M3 screw
Ä
through the smaller 3.5 mm (
1
/
8
in.)
hole.
17
Repeat steps 15–16 to secure the remaining nut plates to the
mounting surface.
18
Install the rubber gasket
Å
on the back of the device.
The pieces of the rubber gasket have adhesive on the back.
Make sure you remove the protective liner before installing
them on the device.
19
If you will not have access to the back of the device after you
mount it, connect all necessary cables to the device before
placing it into the cutout.
NOTE: To prevent corrosion of the metal contacts, cover
unused connectors with the attached weather caps.
20
Apply marine sealant between the mounting surface and the
device to properly seal and prevent leakage behind the
dashboard.
21
If you will have access to the back of the device, apply
marine sealant around the cutout.
2
22
Place the device into the cutout.
23
Secure the device to the mounting surface using the included
M4 screws
Æ
.
24
Wipe away all excess marine sealant.
25
Install the decorative bezel by snapping it in place around the
edges of the device.
Cable and Connection Considerations
The cables may have been packaged without the locking
rings installed. If so, you should route the cables before you
install the locking rings.
After connecting a locking ring to a cable, make sure the ring
is securely connected and the O-ring is in place so the
connection remains secure.
Power/NMEA
®
0183 Cable
The wiring harness connects the device to power, NMEA
0183 devices, and a lamp or a horn for visible or audible
alerts.
If it is necessary to extend the NMEA 0183 or alarm wires,
you must use 22 AWG (.33 mm²) wire.
Item Wire Color Wire Function
Ê
Red Power
Ë
Black Ground (power and NMEA 0183)
Ì
Blue NMEA 0183 internal port 1 Tx (out)
Í
Brown NMEA 0183 internal port 1 Rx (in)
Î
Gray NMEA 0183 internal port 2 Tx (out)
Ï
Violet NMEA 0183 internal port 2 Rx (in)
Ð
Orange Accessory on
Ñ
Yellow Alarm low
Connecting the Wiring Harness to Power
WARNING
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
1
Route the wiring harness to the power source and to the
device.
2
Connect the red wire to the positive (+) battery terminal, and
connect the black wire to the negative (-) battery terminal.
3
If necessary, install the locking ring and O-ring on the end of
the wiring harness.
4
Insert the cable into the POWER connector on the back of
the device, pushing firmly.
5
Turn the locking ring clockwise to attach the cable to the
device.
Additional Grounding Consideration
This consideration is applicable only to devices that have a
grounding screw. Not all models have a grounding screw.
This device should not need additional chassis grounding in
most installation situations. If you experience interference, the
grounding screw on the housing can be used to connect the
device to the water ground of the boat to help avoid the
interference.
Garmin Marine Network Considerations
NOTICE
A Garmin Power over Ethernet (PoE) Isolation Coupler (P/N
010-10580-10) must be used when connecting any third-party
device, such as a FLIR
®
camera, to a Garmin Marine Network.
Connecting a PoE device directly to a Garmin Marine Network
chartplotter damages the Garmin chartplotter and may damage
the PoE device. Connecting any third-party device directly to a
Garmin Marine Network chartplotter will cause abnormal
behavior on the Garmin devices, including the devices not
properly turning off or the software becoming inoperable.
This device can connect to additional Garmin Marine Network
devices to share data such as radar, sonar, and detailed
mapping. When connecting Garmin Marine Network devices to
this device, observe these considerations.
All devices connected to the Garmin Marine Network must be
connected to the same ground.
A Garmin Marine Network cable must be used for all Garmin
Marine Network connections.
Third-party CAT5 cable and RJ45 connectors must not be
used for Garmin Marine Network connections.
Additional Garmin Marine Network cables and connectors
are available from your Garmin dealer.
The NETWORK ports on the device each act as a network
switch. Any compatible device can be connected to any
NETWORK port to share data with all devices on the boat
connected by a Garmin Marine Network cable.
NMEA 2000
®
Considerations
NOTICE
If you are connecting this device to an existing NMEA 2000
network, the NMEA 2000 network should already be connected
to power. Do not connect the NMEA 2000 power cable to an
existing NMEA 2000 network, because only one power source
should be connected to a NMEA 2000 network.
If you are connecting this device to an existing NMEA 2000
network or engine network by another manufacturer, you should
install a NMEA 2000 Power Isolator (010-11580-00) between
the existing network and the Garmin devices.
If you are installing a NMEA 2000 power cable, you must
connect it to the boat ignition switch or through another in-line
switch. NMEA 2000 devices will drain your battery if the NMEA
2000 power cable is connected to the battery directly.
This device can connect to a NMEA 2000 network on your boat
to share data from NMEA 2000 compatible devices such as a
GPS antenna or a VHF radio. The included NMEA 2000 cables
and connectors allow you to connect the device to your existing
NMEA 2000 network. If you do not have an existing NMEA 2000
network you can create a basic one using cables from Garmin.
If you are unfamiliar with NMEA 2000, you should read the
“NMEA 2000 Network Fundamentals” chapter of the Technical
Reference for NMEA 2000 Products. You can find this document
using the “Manuals” link on the product page for your device at
www.garmin.com.
3
The port labeled NMEA 2000 is used to connect the device to a
standard NMEA 2000 network.
Item Description
À
NMEA 2000 compatible Garmin device
Á
GPS antenna
Â
Ignition or in-line switch
Ã
NMEA 2000 power cable
Ä
NMEA 2000 drop cable
Å
12 Vdc power source
Æ
NMEA 2000 terminator or backbone cable
Ç
NMEA 2000 T-connector
È
NMEA 2000 terminator or backbone cable
NMEA 0183 Connection Considerations
See the installation instructions for the NMEA 0183 device to
identify the transmit (Tx) A (+) and B (-) wires and receive
(Rx) A (+) and B (-) wires.
Each internal Rx and Tx port has 2 wires, labeled A (+) and B
(-) according to the NMEA 0183 convention. The
corresponding A (+) and B (-) wires of each internal port
should be connected to the A (+) and B (-) wires of the NMEA
0183 device. See the table and wiring diagrams when
connecting the data cable to NMEA 0183 devices.
You must use 28 AWG, shielded, twisted-pair wiring for
extended runs of wire. Solder all connections and seal them
with heat-shrink tubing.
See NMEA 0183 Information, page 6 for a list of the
approved NMEA 0183 sentences that are output by and input
to your device.
The internal NMEA 0183 ports and communication protocols
are configured on the connected Garmin device. See the
NMEA 0183 section of the chartplotter owner's manual for
more information.
The ground wires on the NMEA 0183 data cable and your
NMEA 0183 device must both be connected to ground.
When connecting NMEA 0183 devices with two transmitting
and two receiving wires, it is not necessary for the NMEA
0183 devices to connect to a common ground.
When connecting a NMEA 0183 device with only one
transmitting (Tx) wire or with only one receiving (Rx) wire, the
NMEA 0183 devices must be connected to a common
ground.
For two-way communication with a NMEA 0183 device, the
internal ports on the NMEA 0183 data cable are not linked.
For example, if the input of the NMEA 0183 device is
connected to the internal output port 1 on the data cable, you
can connect the output port of your NMEA 0183 device to
any of the internal input ports (port 1, port 2, port 3, or port 4)
on the wiring harness.
There are four internal NMEA 0183 input ports (Rx ports),
and two internal NMEA 0183 output (Tx ports) on the
included NMEA 0183 data cable. You can connect one
NMEA 0183 device per internal Rx port to input data to your
Garmin device, and you can connect up to three NMEA 0183
devices in parallel to each internal Tx port to receive data
output by your Garmin device.
NMEA 0183 Connection Diagram
+
-
Item Description
À
12 Vdc power source
Á
Wiring harness
Â
NMEA 0183 compliant device
Item Garmin Wire
Function
Garmin Wire
Color
NMEA 0183 Device Wire
Function
Ê
Power Red Power
Ë
Ground Black Data ground
Ì
Tx/Rx Tx/Rx/B (-)
Í
Tx Blue Rx/A (+)
Î
Rx Brown Tx/A (+)
Lamp or Horn Connections
The device can be used with a lamp, a horn, or both, to sound or
flash an alert when the chartplotter displays a message. This is
optional, and the alarm wire is not necessary for the device to
function normally. When connecting the device to a lamp or
horn, observe these considerations.
The alarm circuit switches to a low-voltage state when the
alarm sounds.
The maximum current is 100 mA, and a relay is needed to
limit the current from the chartplotter to 100 mA.
To manually toggle visual and audible alerts, you can install
single-pole, single-throw switches.
Item Description
À
Power source
Á
Power cable
Â
Horn
Ã
Lamp
Ä
Relay (100 mA coil current)
Å
Toggle switches to enable and disable lamp or horn alerts
Item Wire Color Wire Function
Ê
Red Power
Ë
Black Ground
Ì
Yellow Alarm
Video Input and Output Considerations
This device allows video input from composite video sources
and video output to a monitor, depending on the model. When
4
connecting video input and output sources, observe these
considerations.
The chartplotter may have one composite-video input port
labeled CVBS IN or two composite-video input ports labeled
VIDEO 1 and VIDEO 2.
The composite-video ports use BNC connectors. You can
use a BNC to RCA adapter to connect a composite-video
source with RCA connectors to these ports.
The video from sources connected to these ports is
available only for display on the device or on an additional
monitor connected to the device. Composite video is not
shared across the Garmin Marine Network or NMEA 2000
network.
The chartplotter may have one DVI-D video output port. You
can connect a DVI-D or DVI-I cable to the port to view a
mirror image of the screen on a computer monitor or HD TV.
If your device includes a DVI cable connector, a rubber
gasket is included. This gasket must be installed between
the DVI port and cable connector to avoid damage to the
connector.
If needed, you can use a DVI-D to HDMI
®
adapter to
connect to an HD TV or other HDMI compatible display.
Although it is recommended to use DVI cables sold by
Garmin, high-quality third-party DVI cables may be used.
You should test the DVI cable by connecting the devices
before routing the cable.
J1939 Engine Network Connection Considerations
NOTICE
You must use a Garmin GPSMAP J1939 accessory cable when
connecting the chartplotter to the J1939 engine network to
prevent corrosion due to moisture. Using a different cable voids
your warranty.
If you have an existing engine network on your boat, it should
already be connected to power. Do not add any additional power
supply.
This chartplotter can connect to an engine network on your boat
to read data from compatible devices such as certain engines.
The engine network follows a standard and uses proprietary
messages.
You should connect only one chartplotter to one engine network.
Connecting more than one chartplotter to one engine network
may result in unexpected behavior.
The port labeled J1939 is used to connect the device to the
existing engine network. You must route the cable within 6 m
(20 ft.) of the engine network backbone.
The Garmin GPSMAP J1939 accessory cable requires
connection to a power source and proper termination. For more
information on connecting to your engine network, see the
manufacturer's engine documentation.
Pin Wire Color Description
À
Bare Shield
Á
Red Power, positive
Â
Black Power, negative
Ã
White CAN High
Ä
Blue CAN Low
Specifications
Physical Specifications
Device Specification Measurement
All models Temperature range From -15° to 55°C (5° to
131°F)
Material Die-cast aluminum and
polycarbonate plastic
Water rating* IEC 60529 IPX7
Seven-inch
models
Dimensions (W × H ×
D)
222 × 142 × 66 mm (8.75 ×
5.6 × 2.6 in.)
Display size (W × H) 155 × 86 mm (6.1 × 3.4 in.)
Weight 1.13 kg (2.5 lbs)
Eight-inch
models
Dimensions (W × H ×
D)
244 × 160 × 76 mm (9.6 ×
6.3 × 3.0 in.)
Display size (W × H) 178 × 102 mm (7.0 × 4.0 in.)
Weight 1.41 kg (3.1 lbs)
Ten-inch
models
Dimensions (W × H ×
D)
290 × 206 × 79 mm (11.4 ×
8.1 × 3.1 in.)
Display size (W × H) 218 × 135 mm (8.6 × 5.3 in.)
Weight 2.36 kg (5.2 lbs)
Twelve-inch
models
Dimensions (W × H ×
D)
330 × 226 × 79 mm (13.0 ×
8.9 × 3.1 in.)
Display size (W × H) 262 × 163 mm (10.3 ×
6.4 in.)
Weight 2.72 kg (6.0 lbs)
Sixteen-inch
models
Dimensions (W × H ×
D)
426 × 275 × 88 mm (16.76 ×
10.81 × 3.45 in.)
Display size (W × H) 344 × 193 mm (13.55 ×
7.62 in.)
Weight 4.3 kg (9.5 lbs)
*The device withstands incidental exposure to water of up to 1 m
for up to 30 min. For more information, go to www.garmin.com
/waterrating.
Electrical Specifications
Device Specification Measurement
All models Input power From 10 to 32 Vdc
NMEA 2000 LEN 2
NMEA 2000 Draw 75 mA max.
Seven-inch models Max. power usage at
10 Vdc
24 W
Typical current draw at
12 Vdc
1.5 A
Max. current draw at
12 Vdc
2.0 A
Fuse 6 A, 125 V fast-acting
Compass-safe distance 800 mm (31.5 in.)
Eight-inch models Max. power usage at
10 Vdc
27 W
Typical current draw at
12 Vdc
1.8 A
Max. current draw at
12 Vdc
2.3 A
Fuse 6 A, 125 V fast-acting
Compass-safe distance 700 mm (27.6 in.)
5
Device Specification Measurement
Ten-inch models Max. power usage at
10 Vdc
30 W
Typical current draw at
12 Vdc
1.95 A
Max. current draw at
12 Vdc
2.5 A
Fuse 6 A, 125 V fast-acting
Compass-safe distance 650 mm (25.6 in.)
Twelve-inch
models
Max. power usage at
10 Vdc
36 W
Typical current draw at
12 Vdc
2.5 A
Max. current draw at
12 Vdc
3.0 A
Fuse 6 A, 125 V fast-acting
Compass-safe distance 650 mm (25.6 in.)
Sixteen-inch
models
Max. power usage at
10 Vdc
57.2 W
Typical current draw at
12 Vdc
3.82 A
Max. current draw at
12 Vdc
5.24 A
Fuse 8 A, 125 V fast-acting
Compass-safe distance 850 mm (33.5 in.)
NMEA 2000 PGN Information
Type PGN Description
Transmit and receive 059392 ISO acknowledgment
059904 ISO request
060928 ISO address claim
126208 NMEA: Command, request, and
acknowledge group function
126464 Transmit and receive PGN list group
function
126996 Product information
127250 Vessel heading
128259 Speed: Water referenced
128267 Water depth
129025 Position: Rapid update
129026 COG and SOG: Rapid update
129029 GNSS position data
129540 GNSS satellites in view
130306 Wind data
130312 Temperature
Transmit 127258 Magnetic variance
129283 Cross track error
129284 Navigation data
129285 Navigation route and waypoint info
Receive 065030 Generator average basic AC quantities
(GAAC)
126992 System time
127488 Engine parameters: Rapid update
127489 Engine parameters: Dynamic
127493 Transmission parameters: Dynamic
127504 AC output status
127505 Fluid level
127508 Battery status
129038 AIS class A position report
129039 AIS class B position report
129040 AIS class B extended position report
129539 GNSS DOPs
Type PGN Description
129794 AIS class A static and voyage related
data
129809 AIS class B "CS" static data report, part
A
129810 AIS class B "CS" static data report, part
B
130310 Environmental parameters
130311 Environmental parameters (obsolete)
130313 Humidity
130314 Actual pressure
NMEA 0183 Information
Type Sentence Description
Transmit GPAPB APB: Heading or track controller
(autopilot) sentence "B"
GPBOD BOD: Bearing (origin to
destination)
GPBWC BWC: Bearing and distance to
waypoint
GPGGA GGA: Global positioning system
fix data
GPGLL GLL: Geographic position
(latitude and longitude)
GPGSA GSA: GNSS DOP and active
satellites
GPGSV GSV: GNSS satellites in view
GPRMB RMB: Recommended minimum
navigation information
GPRMC RMC: Recommended minimum
specific GNSS data
GPRTE RTE: Routes
GPVTG VTG: Course over ground and
ground speed
GPWPL WPL: Waypoint location
GPXTE XTE: Cross track error
PGRME E: Estimated error
PGRMM M: Map datum
PGRMZ Z: Altitude
SDDBT DBT: Depth below transducer
SDDPT DPT: Depth
SDMTW MTW: Water temperature
SDVHW VHW: Water speed and heading
Receive DPT Depth
DBT Depth below transducer
MTW Water temperature
VHW Water speed and heading
WPL Waypoint location
DSC Digital selective calling
information
DSE Expanded digital selective calling
HDG Heading, deviation, and variation
HDM Heading, magnetic
MWD Wind direction and speed
MDA Meteorological composite
MWV Wind speed and angle
VDM AIS VHF data-link message
You can purchase complete information about National Marine
Electronics Association (NMEA) format and sentences from: NMEA,
Seven Riggs Avenue, Severna Park, MD 21146 USA (www.nmea.org)
6
J1939 PGN Information
The chartplotter can receive J1939 PGN sentences. The
chartplotter cannot transmit over the J1939 network.
Sentence Description
61443 Electronic engine controller 2
61444 Electronic engine controller 1
65031 Exhaust temperature
65172 Engine auxiliary coolant
65252 Shutdown
65253 Engine hours and revolutions
65262 Engine temperature 1
65263 Engine fluid level or pressure 1
65270 Inlet or exhaust conditions 1
65271 Vehicle electrical power
65279 Water in fuel indicator
65272 Transmission fluids 1
65248 Vehicle distance
65266 Fuel economy (liquid)
65276 Dash display
65226 Active diagnostic trouble codes
© 2016–2017 Garmin Ltd. or its subsidiaries
Garmin
®
, the Garmin logo, and GPSMAP
®
are trademarks of Garmin Ltd. or its
subsidiaries, registered in the USA and other countries. These trademarks may not be
used without the express permission of Garmin.
NMEA
®
, NMEA 2000
®
, and the NMEA 2000 logo are registered trademarks of the
National Marine Electronics Association.
HDMI
®
is a registered trademark of HDMI
Licensing, LLC.
7
© 2016–2017 Garmin Ltd. or its subsidiaries support.garmin.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Garmin GPSMAP 7407 Manuale del proprietario

Tipo
Manuale del proprietario

in altre lingue