Garmin GPSMAP® 7612 Manuale del proprietario

Marca: Garmin

Modello: GPSMAP® 7612

Tipo: Manuale del proprietario

GPSMAP

7400/7600

Series

Installation Instructions

Important Safety Information

WARNING

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place voids the product warranty.

CAUTION

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

To obtain the best performance and to avoid damage to your

boat, install the device according to these instructions.

Read all installation instructions before proceeding with the

installation. If you experience difficulty during the installation,

contact Garmin

Product Support.

Registering Your Device

Help us better support you by completing our online registration

today.

• Go to my.garmin.com.

• Keep the original sales receipt, or a photocopy, in a safe

place.

Contacting Garmin Support

• Go to support.garmin.com for help and information, such as

product manuals, frequently asked questions, videos, and

customer support.

• In the USA, call 913-397-8200 or 1-800-800-1020.

• In the UK, call 0808 238 0000.

• In Europe, call +44 (0) 870 850 1241.

Software Update

You may need to update the device software when you install

the device or add an accessory to the device.

This device supports up to a 32 GB memory card, formatted to

FAT32.

Loading the New Software on a Memory Card

Insert a memory card into the card slot on the computer.

Go to www.garmin.com/support/software/marine.html.

Select Download next to GPSMAP Series with SD Card.

Read and agree to the terms.

Select Download.

Select Run.

Select the drive associated with the memory card, and select

Next > Finish.

Updating the Device Software

Before you can update the software, you must obtain a

software-update memory card or load the latest software onto a

memory card.

Turn on the chartplotter.

After the home screen appears, insert the memory card into

the card slot.

NOTE: In order for the software update instructions to

appear, the device must be fully booted before the card is

inserted.

Follow the on-screen instructions.

Wait several minutes while the software update process

completes.

When prompted, leave the memory card in place and restart

the chartplotter manually.

Remove the memory card.

NOTE: If the memory card is removed before the device

restarts fully, the software update is not complete.

Tools Needed

• Drill and drill bits

◦ Bail mount: drill bits appropriate for the surface and

hardware

◦ Flush mount: 13 mm (

in.) drill bit, 7.2 mm (

in.), and

3.5 mm (

in.) drill bit

• #2 Phillips screwdriver

• Jigsaw or rotary tool

• File and sandpaper

• Marine sealant (recommended)

Mounting Considerations

NOTICE

This device should be mounted in a location that is not exposed

to extreme temperatures or conditions. The temperature range

for this device is listed in the product specifications. Extended

exposure to temperatures exceeding the specified temperature

range, in storage or operating conditions, may cause device

failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

When selecting a mounting location, you should observe these

considerations.

• The location should provide optimal viewing as you operate

your boat.

• The location should allow for easy access to all device

interfaces, such as the keypad, touchscreen, and card

reader, if applicable.

• The location must be strong enough to support the weight of

the device and protect it from excessive vibration or shock.

• To avoid interference with a magnetic compass, the device

should not be installed closer to a compass than the

compass-safe distance value listed in the product

specifications.

• The location must allow room for the routing and connection

of all cables.

January 2017

Printed in Taiwan 190-02071-02_0C

• The location must not be a flat, horizontal surface. The

location should be in a vertical angle.

The location and viewing angle should be tested before you

install the device. High viewing angles from above and below

the display may result in a poor image.

Bail Mounting the Device

NOTICE

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid cracking in the gel-coat layer when the screws are

tightened.

The bail-mounting hardware (screws and washers, or nuts,

washers, and bolts) is not included. The bail mount bracket is

included in some models. Before you can bail mount the device,

you must purchase a bail mount bracket, if necessary. You must

also purchase mounting hardware that fits the holes in the bail

mount bracket and securely attaches it to your specific mounting

surface. The size of the pilot holes required depends on the

mounting hardware you purchase.

Using the bail mount bracket

as a template, mark the

location of the four pilot holes

Using a drill bit appropriate for your mounting hardware, drill

the pilot holes.

Secure the bail mount bracket to the surface using your

mounting hardware

Install the bail mount knobs

on the sides of the device.

Place the device in the bail mount bracket, and tighten the

bail mount knobs.

Flush Mounting the Device

NOTICE

Be careful when cutting the hole to flush mount the device.

There is only a small amount of clearance between the case and

the mounting holes, and cutting the hole too large could

compromise the stability of the device after it is mounted.

The included template and hardware can be used to flush mount

the device in your dashboard.

Trim the template, and make sure it fits in the location where

you want to mount the device.

Secure the template to the selected location.

Using a 13 mm (

in.) drill bit, drill one or more of the holes

inside the corners of the solid line on the template to prepare

the mounting surface for cutting.

Using a jigsaw or a rotary tool, cut the mounting surface

along the inside line on the template.

Place the device in the cutout to test the fit.

If necessary, use a file and sandpaper to refine the size of

the cutout.

After the device fits correctly in the cutout, ensure the

mounting holes on the device line up with the larger 7.2 mm

(

in.) holes on the template.

If the mounting holes on the device do not line up, mark the

new hole locations.

Using a 7.2 mm (

in.) drill bit, drill the larger holes.

Starting in one corner of the template, place a nut plate

over the larger hole

drilled in step 9.

The smaller 3.5 mm (

in.) hole

on the nut plate should

line up with the smaller hole on the template.

If the smaller 3.5 mm (

in.) hole on the nut plate does not

line up with the smaller hole on the template, mark the new

hole location.

Repeat steps 10 and 11 to verify placement of the remaining

nut plates and holes on the template.

Using a 3.5 mm (

in.) drill bit, drill the smaller holes.

Remove the template from the mounting surface.

Starting in one corner of the mounting location, place a nut

plate

on the back of the mounting surface, lining up the

large and small holes.

The raised portion of the nut plate should fit into the larger

hole.

Secure the nut plate to the mounting surface by fastening an

included M3 screw

through the smaller 3.5 mm (

in.)

hole.

Repeat steps 15–16 to secure the remaining nut plates to the

mounting surface.

Install the rubber gasket

on the back of the device.

The pieces of the rubber gasket have adhesive on the back.

Make sure you remove the protective liner before installing

them on the device.

If you will not have access to the back of the device after you

mount it, connect all necessary cables to the device before

placing it into the cutout.

NOTE: To prevent corrosion of the metal contacts, cover

unused connectors with the attached weather caps.

Apply marine sealant between the mounting surface and the

device to properly seal and prevent leakage behind the

dashboard.

If you will have access to the back of the device, apply

marine sealant around the cutout.

Place the device into the cutout.

Secure the device to the mounting surface using the included

M4 screws

Wipe away all excess marine sealant.

Install the decorative bezel by snapping it in place around the

edges of the device.

Cable and Connection Considerations

• The cables may have been packaged without the locking

rings installed. If so, you should route the cables before you

install the locking rings.

• After connecting a locking ring to a cable, make sure the ring

is securely connected and the O-ring is in place so the

connection remains secure.

Power/NMEA

0183 Cable

• The wiring harness connects the device to power, NMEA

0183 devices, and a lamp or a horn for visible or audible

alerts.

• If it is necessary to extend the NMEA 0183 or alarm wires,

you must use 22 AWG (.33 mm²) wire.

Item Wire Color Wire Function

Red Power

Black Ground (power and NMEA 0183)

Blue NMEA 0183 internal port 1 Tx (out)

Brown NMEA 0183 internal port 1 Rx (in)

Gray NMEA 0183 internal port 2 Tx (out)

Violet NMEA 0183 internal port 2 Rx (in)

Orange Accessory on

Yellow Alarm low

Connecting the Wiring Harness to Power

WARNING

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place voids the product warranty.

Route the wiring harness to the power source and to the

device.

Connect the red wire to the positive (+) battery terminal, and

connect the black wire to the negative (-) battery terminal.

If necessary, install the locking ring and O-ring on the end of

the wiring harness.

Insert the cable into the POWER connector on the back of

the device, pushing firmly.

Turn the locking ring clockwise to attach the cable to the

device.

Additional Grounding Consideration

This consideration is applicable only to devices that have a

grounding screw. Not all models have a grounding screw.

This device should not need additional chassis grounding in

most installation situations. If you experience interference, the

grounding screw on the housing can be used to connect the

device to the water ground of the boat to help avoid the

interference.

Garmin Marine Network Considerations

NOTICE

A Garmin Power over Ethernet (PoE) Isolation Coupler (P/N

010-10580-10) must be used when connecting any third-party

device, such as a FLIR

camera, to a Garmin Marine Network.

Connecting a PoE device directly to a Garmin Marine Network

chartplotter damages the Garmin chartplotter and may damage

the PoE device. Connecting any third-party device directly to a

Garmin Marine Network chartplotter will cause abnormal

behavior on the Garmin devices, including the devices not

properly turning off or the software becoming inoperable.

This device can connect to additional Garmin Marine Network

devices to share data such as radar, sonar, and detailed

mapping. When connecting Garmin Marine Network devices to

this device, observe these considerations.

• All devices connected to the Garmin Marine Network must be

connected to the same ground.

• A Garmin Marine Network cable must be used for all Garmin

Marine Network connections.

◦ Third-party CAT5 cable and RJ45 connectors must not be

used for Garmin Marine Network connections.

◦ Additional Garmin Marine Network cables and connectors

are available from your Garmin dealer.

• The NETWORK ports on the device each act as a network

switch. Any compatible device can be connected to any

NETWORK port to share data with all devices on the boat

connected by a Garmin Marine Network cable.

NMEA 2000

Considerations

NOTICE

If you are connecting this device to an existing NMEA 2000

network, the NMEA 2000 network should already be connected

to power. Do not connect the NMEA 2000 power cable to an

existing NMEA 2000 network, because only one power source

should be connected to a NMEA 2000 network.

If you are connecting this device to an existing NMEA 2000

network or engine network by another manufacturer, you should

install a NMEA 2000 Power Isolator (010-11580-00) between

the existing network and the Garmin devices.

If you are installing a NMEA 2000 power cable, you must

connect it to the boat ignition switch or through another in-line

switch. NMEA 2000 devices will drain your battery if the NMEA

2000 power cable is connected to the battery directly.

This device can connect to a NMEA 2000 network on your boat

to share data from NMEA 2000 compatible devices such as a

GPS antenna or a VHF radio. The included NMEA 2000 cables

and connectors allow you to connect the device to your existing

NMEA 2000 network. If you do not have an existing NMEA 2000

network you can create a basic one using cables from Garmin.

If you are unfamiliar with NMEA 2000, you should read the

“NMEA 2000 Network Fundamentals” chapter of the Technical

Reference for NMEA 2000 Products. You can find this document

using the “Manuals” link on the product page for your device at

www.garmin.com.

The port labeled NMEA 2000 is used to connect the device to a

standard NMEA 2000 network.

Item Description

NMEA 2000 compatible Garmin device

GPS antenna

Ignition or in-line switch

NMEA 2000 power cable

NMEA 2000 drop cable

12 Vdc power source

NMEA 2000 terminator or backbone cable

NMEA 2000 T-connector

NMEA 2000 terminator or backbone cable

NMEA 0183 Connection Considerations

• See the installation instructions for the NMEA 0183 device to

identify the transmit (Tx) A (+) and B (-) wires and receive

(Rx) A (+) and B (-) wires.

• Each internal Rx and Tx port has 2 wires, labeled A (+) and B

(-) according to the NMEA 0183 convention. The

corresponding A (+) and B (-) wires of each internal port

should be connected to the A (+) and B (-) wires of the NMEA

0183 device. See the table and wiring diagrams when

connecting the data cable to NMEA 0183 devices.

• You must use 28 AWG, shielded, twisted-pair wiring for

extended runs of wire. Solder all connections and seal them

with heat-shrink tubing.

• See NMEA 0183 Information, page 6 for a list of the

approved NMEA 0183 sentences that are output by and input

to your device.

• The internal NMEA 0183 ports and communication protocols

are configured on the connected Garmin device. See the

NMEA 0183 section of the chartplotter owner's manual for

more information.

• The ground wires on the NMEA 0183 data cable and your

NMEA 0183 device must both be connected to ground.

• When connecting NMEA 0183 devices with two transmitting

and two receiving wires, it is not necessary for the NMEA

0183 devices to connect to a common ground.

• When connecting a NMEA 0183 device with only one

transmitting (Tx) wire or with only one receiving (Rx) wire, the

NMEA 0183 devices must be connected to a common

ground.

• For two-way communication with a NMEA 0183 device, the

internal ports on the NMEA 0183 data cable are not linked.

For example, if the input of the NMEA 0183 device is

connected to the internal output port 1 on the data cable, you

can connect the output port of your NMEA 0183 device to

any of the internal input ports (port 1, port 2, port 3, or port 4)

on the wiring harness.

• There are four internal NMEA 0183 input ports (Rx ports),

and two internal NMEA 0183 output (Tx ports) on the

included NMEA 0183 data cable. You can connect one

NMEA 0183 device per internal Rx port to input data to your

Garmin device, and you can connect up to three NMEA 0183

devices in parallel to each internal Tx port to receive data

output by your Garmin device.

NMEA 0183 Connection Diagram

Item Description

12 Vdc power source

Wiring harness

NMEA 0183 compliant device

Item Garmin Wire

Function

Garmin Wire

Color

NMEA 0183 Device Wire

Function

Power Red Power

Ground Black Data ground

Tx/Rx Tx/Rx/B (-)

Tx Blue Rx/A (+)

Rx Brown Tx/A (+)

Lamp or Horn Connections

The device can be used with a lamp, a horn, or both, to sound or

flash an alert when the chartplotter displays a message. This is

optional, and the alarm wire is not necessary for the device to

function normally. When connecting the device to a lamp or

horn, observe these considerations.

• The alarm circuit switches to a low-voltage state when the

alarm sounds.

• The maximum current is 100 mA, and a relay is needed to

limit the current from the chartplotter to 100 mA.

• To manually toggle visual and audible alerts, you can install

single-pole, single-throw switches.

Item Description

Power source

Power cable

Horn

Lamp

Relay (100 mA coil current)

Toggle switches to enable and disable lamp or horn alerts

Item Wire Color Wire Function

Red Power

Black Ground

Yellow Alarm

Video Input and Output Considerations

This device allows video input from composite video sources

and video output to a monitor, depending on the model. When

connecting video input and output sources, observe these

considerations.

• The chartplotter may have one composite-video input port

labeled CVBS IN or two composite-video input ports labeled

VIDEO 1 and VIDEO 2.

◦ The composite-video ports use BNC connectors. You can

use a BNC to RCA adapter to connect a composite-video

source with RCA connectors to these ports.

◦ The video from sources connected to these ports is

available only for display on the device or on an additional

monitor connected to the device. Composite video is not

shared across the Garmin Marine Network or NMEA 2000

network.

• The chartplotter may have one DVI-D video output port. You

can connect a DVI-D or DVI-I cable to the port to view a

mirror image of the screen on a computer monitor or HD TV.

◦ If your device includes a DVI cable connector, a rubber

gasket is included. This gasket must be installed between

the DVI port and cable connector to avoid damage to the

connector.

◦ If needed, you can use a DVI-D to HDMI

adapter to

connect to an HD TV or other HDMI compatible display.

◦ Although it is recommended to use DVI cables sold by

Garmin, high-quality third-party DVI cables may be used.

You should test the DVI cable by connecting the devices

before routing the cable.

J1939 Engine Network Connection Considerations

NOTICE

You must use a Garmin GPSMAP J1939 accessory cable when

connecting the chartplotter to the J1939 engine network to

prevent corrosion due to moisture. Using a different cable voids

your warranty.

If you have an existing engine network on your boat, it should

already be connected to power. Do not add any additional power

supply.

This chartplotter can connect to an engine network on your boat

to read data from compatible devices such as certain engines.

The engine network follows a standard and uses proprietary

messages.

You should connect only one chartplotter to one engine network.

Connecting more than one chartplotter to one engine network

may result in unexpected behavior.

The port labeled J1939 is used to connect the device to the

existing engine network. You must route the cable within 6 m

(20 ft.) of the engine network backbone.

The Garmin GPSMAP J1939 accessory cable requires

connection to a power source and proper termination. For more

information on connecting to your engine network, see the

manufacturer's engine documentation.

Pin Wire Color Description

Bare Shield

Red Power, positive

Black Power, negative

White CAN High

Blue CAN Low

Specifications

Physical Specifications

Device Specification Measurement

All models Temperature range From -15° to 55°C (5° to

131°F)

Material Die-cast aluminum and

polycarbonate plastic

Water rating* IEC 60529 IPX7

Seven-inch

models

Dimensions (W × H ×

222 × 142 × 66 mm (8.75 ×

5.6 × 2.6 in.)

Display size (W × H) 155 × 86 mm (6.1 × 3.4 in.)

Weight 1.13 kg (2.5 lbs)

Eight-inch

models

Dimensions (W × H ×

244 × 160 × 76 mm (9.6 ×

6.3 × 3.0 in.)

Display size (W × H) 178 × 102 mm (7.0 × 4.0 in.)

Weight 1.41 kg (3.1 lbs)

Ten-inch

models

Dimensions (W × H ×

290 × 206 × 79 mm (11.4 ×

8.1 × 3.1 in.)

Display size (W × H) 218 × 135 mm (8.6 × 5.3 in.)

Weight 2.36 kg (5.2 lbs)

Twelve-inch

models

Dimensions (W × H ×

330 × 226 × 79 mm (13.0 ×

8.9 × 3.1 in.)

Display size (W × H) 262 × 163 mm (10.3 ×

6.4 in.)

Weight 2.72 kg (6.0 lbs)

Sixteen-inch

models

Dimensions (W × H ×

426 × 275 × 88 mm (16.76 ×

10.81 × 3.45 in.)

Display size (W × H) 344 × 193 mm (13.55 ×

7.62 in.)

Weight 4.3 kg (9.5 lbs)

*The device withstands incidental exposure to water of up to 1 m

for up to 30 min. For more information, go to www.garmin.com

/waterrating.

Electrical Specifications

Device Specification Measurement

All models Input power From 10 to 32 Vdc

NMEA 2000 LEN 2

NMEA 2000 Draw 75 mA max.

Seven-inch models Max. power usage at

10 Vdc

24 W

Typical current draw at

12 Vdc

1.5 A

Max. current draw at

12 Vdc

2.0 A

Fuse 6 A, 125 V fast-acting

Compass-safe distance 800 mm (31.5 in.)

Eight-inch models Max. power usage at

10 Vdc

27 W

Typical current draw at

12 Vdc

1.8 A

Max. current draw at

12 Vdc

2.3 A

Fuse 6 A, 125 V fast-acting

Compass-safe distance 700 mm (27.6 in.)

Device Specification Measurement

Ten-inch models Max. power usage at

10 Vdc

30 W

Typical current draw at

12 Vdc

1.95 A

Max. current draw at

12 Vdc

2.5 A

Fuse 6 A, 125 V fast-acting

Compass-safe distance 650 mm (25.6 in.)

Twelve-inch

models

Max. power usage at

10 Vdc

36 W

Typical current draw at

12 Vdc

2.5 A

Max. current draw at

12 Vdc

3.0 A

Fuse 6 A, 125 V fast-acting

Compass-safe distance 650 mm (25.6 in.)

Sixteen-inch

models

Max. power usage at

10 Vdc

57.2 W

Typical current draw at

12 Vdc

3.82 A

Max. current draw at

12 Vdc

5.24 A

Fuse 8 A, 125 V fast-acting

Compass-safe distance 850 mm (33.5 in.)

NMEA 2000 PGN Information

Type PGN Description

Transmit and receive 059392 ISO acknowledgment

059904 ISO request

060928 ISO address claim

126208 NMEA: Command, request, and

acknowledge group function

126464 Transmit and receive PGN list group

function

126996 Product information

127250 Vessel heading

128259 Speed: Water referenced

128267 Water depth

129025 Position: Rapid update

129026 COG and SOG: Rapid update

129029 GNSS position data

129540 GNSS satellites in view

130306 Wind data

130312 Temperature

Transmit 127258 Magnetic variance

129283 Cross track error

129284 Navigation data

129285 Navigation route and waypoint info

Receive 065030 Generator average basic AC quantities

(GAAC)

126992 System time

127488 Engine parameters: Rapid update

127489 Engine parameters: Dynamic

127493 Transmission parameters: Dynamic

127504 AC output status

127505 Fluid level

127508 Battery status

129038 AIS class A position report

129039 AIS class B position report

129040 AIS class B extended position report

129539 GNSS DOPs

Type PGN Description

129794 AIS class A static and voyage related

data

129809 AIS class B "CS" static data report, part

129810 AIS class B "CS" static data report, part

130310 Environmental parameters

130311 Environmental parameters (obsolete)

130313 Humidity

130314 Actual pressure

NMEA 0183 Information

Type Sentence Description

Transmit GPAPB APB: Heading or track controller

(autopilot) sentence "B"

GPBOD BOD: Bearing (origin to

destination)

GPBWC BWC: Bearing and distance to

waypoint

GPGGA GGA: Global positioning system

fix data

GPGLL GLL: Geographic position

(latitude and longitude)

GPGSA GSA: GNSS DOP and active

satellites

GPGSV GSV: GNSS satellites in view

GPRMB RMB: Recommended minimum

navigation information

GPRMC RMC: Recommended minimum

specific GNSS data

GPRTE RTE: Routes

GPVTG VTG: Course over ground and

ground speed

GPWPL WPL: Waypoint location

GPXTE XTE: Cross track error

PGRME E: Estimated error

PGRMM M: Map datum

PGRMZ Z: Altitude

SDDBT DBT: Depth below transducer

SDDPT DPT: Depth

SDMTW MTW: Water temperature

SDVHW VHW: Water speed and heading

Receive DPT Depth

DBT Depth below transducer

MTW Water temperature

VHW Water speed and heading

WPL Waypoint location

DSC Digital selective calling

information

DSE Expanded digital selective calling

HDG Heading, deviation, and variation

HDM Heading, magnetic

MWD Wind direction and speed

MDA Meteorological composite

MWV Wind speed and angle

VDM AIS VHF data-link message

You can purchase complete information about National Marine

Electronics Association (NMEA) format and sentences from: NMEA,

Seven Riggs Avenue, Severna Park, MD 21146 USA (www.nmea.org)

J1939 PGN Information

The chartplotter can receive J1939 PGN sentences. The

chartplotter cannot transmit over the J1939 network.

Sentence Description

61443 Electronic engine controller 2

61444 Electronic engine controller 1

65031 Exhaust temperature

65172 Engine auxiliary coolant

65252 Shutdown

65253 Engine hours and revolutions

65262 Engine temperature 1

65263 Engine fluid level or pressure 1

65270 Inlet or exhaust conditions 1

65271 Vehicle electrical power

65279 Water in fuel indicator

65272 Transmission fluids 1

65248 Vehicle distance

65266 Fuel economy (liquid)

65276 Dash display

65226 Active diagnostic trouble codes

Garmin

, the Garmin logo, and GPSMAP

are trademarks of Garmin Ltd. or its

subsidiaries, registered in the USA and other countries. These trademarks may not be

used without the express permission of Garmin.

NMEA

, NMEA 2000

, and the NMEA 2000 logo are registered trademarks of the

National Marine Electronics Association.

HDMI

is a registered trademark of HDMI

Licensing, LLC.

Garmin GPSMAP® 7612 Manuale del proprietario

Marca: Garmin

Modello: GPSMAP® 7612

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Garmin GPSMAP® 7612 Owner's manual

Garmin GPSMAP® 7612 Manuale del proprietario

Garmin GPSMAP® 7612 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti