Checker
Certificate of Quality
Sea Elephant
Rev 01
specific number 0040570098
Solar water heater
Please read this manual carefully before use
Please keep this manual for future reference.
User s Manual
`
PJF2-150W
BRF2-150W
Correct disposal of this product:
This marking means that this product should not be
disposed with other household wastes . To prevent
possible harm to the environment or human health
from uncontrolled waste disposal,recycle it
responsibly to promote the sustainable reuse of
material resources. To return your used
device,please use the return and collection systems
or contact the retailer where the product was
purchased, they can take this product for
environmental safe recycling.
Note
16
Product appearance, color or patterns shall refer to the actual machine.
This manual uses recycling paper.
Phenomenon
Please check
How to solve
No water output
Unstable quantity and
temperature with water output
Indication E1
Water exiting is cold
No temperature rising
Is water supply failed or water pressure too low?
Is water exit blocked?Is hot water valve opened?
Indication E3
Large amount of water flows out of
temperature and pressure valve
Indication E4
Is water temperature adjusted?
Is temperature controller loss of control?
Sunshine insufficient
Is Heating element amaged?
Is the tap water pressure stable?
Unable to turn on
Whether components and parts are damaged
Circuit malfunction
Is the sensor of collector damaged?
Is it connected well with power supply board?
Is the sensor of storing tank damaged?
Is it connected well with power supply board?
Whether tap water pressure is too large ( over 0.7MPa
Check
Check and clean
Readjust
Contact repair section
Heat continually
Contact repair section
Check
Contact repair section
Contact repair section
Contact repair section
Contact repair section
Contact repair section
Notes for usage
FAQ
15
Content
Use method
FeaturesFeatures
Electric circuit diagram Electric circuit diagram
Technical dataTechnical data
System structure
Technical parameterTechnical parameter
Before usage
Packing list
Particular warning
Attentions in installment
Installation
Introduction for the controller
Notes for usage
FAQ
Note
Installation guideInstallation guide
FAQFAQ
Antifreeze insufficient
Contact repair section
Use guideUse guide
1
1.Home water heater:
Collector equipment is aslant installed on the rooftop and perfectly integrated
with building, match the building standard and fashion nowadays.
2.Vacuum glass tube is efficient and reliable:
The conductive efficiency of the tube is supernale. Vacuum tube of collector
equipment is without water and dirts, antifreeze, high endurance, efficient and
secure.
3.Selective coat endothermic system
The endothermic system adopts the latest international high-tech. It is
characterized by high absorbing capacity and low reflectivity.
4.Heat water system of enduring pressure:
Water can be supplied in more than one line. The flux of water is enough to use,
the usage of water is comfortable and the regulation of water temperature is
convenient. System run reliably and can be used under all-weather .
5.scientific designing:
Four kinds of working modes are designed to supply water under different
season.Control the running of pump automatically according to different
temperature , enconomizing energy and prolonging life of pump. Possess the
function of digital display of water temperature and multisafeguard, safe to
use,easy to use.
14
FeaturesFeatures
Electric circuit diagram
FeaturesFeatures
Electric circuit diagram Electric circuit diagram
Notes for usage
the serving person.
8.When the system runs continually over one month, you are suggested to
check regularly whether the deviation of the clock is large so as to adjust the
clock promptly and ensure that the preset and intellectual heating modes
operate normally.
9.In cases when the power supply line of the appliance is damaged, it is the
personnel of after service who change that for specially designed lines
(provided by the manufacturer).
10.In cases when the temperature of water-storing tank exceeds 85 , and the
electrical enclosure indicates E2.First,you should cut off power supply,
then,to release a little of hot water and supply some cold water.when the
temperature of water is decrease and then to connect power supply ,the
fault is able to obviate.
11.The temperature difference for running of circulating water pump suggests
that the temperature should be chosen as 15 in seasons when the
sunshine is strong(eg, summer), and 10 in seasons when the sunshine is
weak (eg, winter).
12.When water heater is not used for long and you use it again, to avoid
occurrence of accidents,you shoud exhaust the system, and the system must
be full of water before usage,let the gas which lie in the pipe out,meanwhile,
make sure there is no smoke, fire or other appliances near when you open
the valve,the exhausting way: open the hot water outlet and cold water inlet
valve, when the water come out sustaining after exhausting all the gas, then
close the hot water outlet valve. you had better operation the valve in the low
tempreture,such as wee hours or night, or the life of the system will be
influenced. to check all the parts of the system in good condition, and make
sure the tank full of water, then you can use it.
13.Operation exhaust valve termly so as to clear dirty thing, and insured to
exhaust valve be not block off.
Controller
Display Board
L:
N:
E:
K1 K2 R
EH:H
MT:High
RT1:T
RT2:C
Brown Wire
Blue Wire
YelloW/Green Wire
elay
eating Element
Temperature Limiter
ank Temperature Sensor
ollector Temperature Sensor
RT1
RT2
K1
K2
Pump
E
L
N
Controller
Wire Board
l
e
akag
e Ins
_
Pec
t
io
n Lo
o
p
13
Use method
The first preset heating time .---to set minute of the first preset heating time--
-to set temperature of preset heating .--- to set hour of the second preset
heating time --- to set minute of the second preset heating time---to set
temperature of the second preset heating ---indicating clock condition. For
example: to Set the temperature of the first preset heating, and for the
indication interface,see Fig.12.
Intellectual heating mode:
Indicating clock condition--the temperature of heating --- indicating clock
condition.
Note: Only when the present working mode is selected, can the
corresponding set content be carried out.
1.To avoid that water spurts out to the solar stage and the top cover of water-
storing tank directly.
2.To check the functioning of the system regularly and to check whether the
computer board works normally.
3. In order to ensure excellent running of solar water heater, you are suggested
to keep the controller electrified constantly and keep it working under the
solar energy heating mode.
4.In normal use, the tap water entrance valve of water-storing tank should be
kept constantly open. You only need to open the mixed valve to adjust water
temperature when taking a bath and then you can use freely.
5.In summer when water heater is not used for long, the system should not be
closed so as to avoid that the collector is too hot. When empty the system, you
should empty the tank and the collector. The emptying method of the tank is to
close the valve where tap water pipe leads to the hot water system, to open
the decompression handle of tempteture and pressure valve and remove the
single direction valve1 and to empty the tank.
the emptying method of the pipe of circulating pipe:screw down the the cap of
the affusing liquid valve, open the two small halt valves, the antifreeze will
flow from the small halt valve,put it on something,when the antifreeze stop
flowing,close the big halt valve in the middle of affusing liquid valve,connect
inflator to liquid hole,the method is same with the method of affusing
antifreeze, sure the gas direction and the single direction valve2 is same untill
the antifreeze is cleaned up.
6.Please try to connect the probe of sensor to the bottom of the installed hole in
installment or repair. Please avoid that the sensor receives wrong signals.
7.Affusing liquid valve is the key part of the system,aviod to adjust or remove
the 3 handles and 2 screw caps, if temperature of the tank is low, please
Notes for usage
Notes for usage
Flat collector
Hot water outlet
Cold water inlet
Tee joint
Metal pipe: ( copper or corrugation pipe)
Water-storing tank
Outdoors
Indoors
Single direction valve1
Temperature and
pressure valve
Vacuum tube Collector
Single direction valve2
Solar stage
Affusing liquid valve
Expanding tank
circulating liquid-exiting
circulating liquid-returning
circulating liquid-returning
Metal pipe: ( copper or corrugation pipe)
Single direction valve2
circulating
liquid-exiting
Outdoors
Indoors
Tee joint
Affusing liquid valve
Expanding tank
Solar stage
Single direction valve1
Cold water inlet
Temperature and
pressure valve
Hot water outlet
Wat
er-st
oring
tank
2
System structure
Fig.1 BRF2-150W structure sketch map
Fig.2 PJF2-150W structure sketch map
ͼÈý ¼¯ÈÈÆ÷µÄ°²×°
Decorating object
Crculating water-inleting
Tempreture and
pressure valve
Inside line
Tank sensor
Circulating water-outleting
Top cover
H
ot
w
ate
r
outl
et
Osculum
Top cover
Tank sensor
Inside line
Fig.3 Circulating of tank structure platform
Fig.4 Circulating of tank structure sketch map
Electric controller
REG
MODE
SET
ON/OFF
SOL H PRE INT WT HC
T-DISP
REG
MODE
SET
ON/OFF
T-DISP
Ì«
Ñô
ÄÜ
SOL
H PRE
INT
WT
HC
REG
MODE
SET
ON/OFF
T-DISP
SOL
H PRE
INT
WT
HC
SOL
H PRE
INT
WT
HC
T-DISP
SET
ON/OFF
REG
MODE
3
12
Note: the above parameter errors ( except power value) of the lighting area are 3%,
volume errors are 3%, and the allowed error scope of other sizes is 10%.
¼¯ÈÈÆ÷°ü×°Ïä
Technical parameter
Packing list
Technical parameter
Packing list
Use method
Model
Volume
Water-proof
Grade
Drip-proof
Rated internal
Pressure
Size
Model
Rated voltage
Frequency
Rated Power
Input
Grass Collector area
BRF2-150W
PJF2-150W
230V~
230V~
50Hz
50Hz
2200W
2200W
0.7MPa
0.7MPa
492 530 1380(mm)
3.0m
2
4.0m
2
Drip-proof
Name of components
Packing method
Packing container
of water tank
BRF2-150W PJF2-150W
Users manual
Model
Tee joint*
Opposite wires S1/2F-3/4M
Packing of solar stage
1
3/4 fiber spacer
Collector equipment
Single-direction valve*
1
4
4
1
1
2
2
1
1
1
1
Packing of collector
Note: accessories of BRF2-150W and PJF2-150W products are suitable only for oblique
installment. For flat installment, prop stand of different angles should be made according
to requirements, which is not included in the packing accessories.The part of after which
have * will be carried by server when installation.
Water-storing tank
1
Temperature and pressure valve*
numbers.when set the parameter up to the
highest,press the setting key again,the
number will increase progressivelyfrom
the minimal number.to continually press
more than one second, the adjusted
parameter will increase progressively 3
numbers every second setting of each
parameter can be done by pressing the
setting key or by not pressing the setting
key about 6 seconds. Then the system will
automatically confirm and automatically
enter the next parameter setting, until the
system finally withdraws from the set
conditions and returns to the conditions of
the previous clock. The set order of
parameter in specific modes is as follows:
Solar energy heating mode:
Indicating clock condition---to check the
hour of clock---to check the minute of
clock---to set temperature difference of
water pump running--- indicating clock
condition. For example: temperature
difference value setting of water pump
running: to press the setting key to enter
the setting condition of temperature
difference of water pump running. The
indication board indicates the present set
value (the first place on the left of the clock
number tube indicates L , and the
following two places indicate the tacitly
approved set value, which is 15 ). To
press the setting key to select between 15
and 10 . For the indication interface,
see Fig.11.
Simultaneous heating mode:
Indication clock condition--- the
temperature of heating---indication clock
condition.
Preset heating mode:
Indicating clock condition---to set hour of
`
492 530 1380(mm)
150L
150L
BRF2-150W
PJF2-150W
Affusing liquid valve*
Small expanding bolt
Large expanding bolt
Solar stage pothook
Expanging tank fixity
Expanding tank
Solar stage
Fig.9 solar heating interface
Fig.11 temperature difference
setting interface for water pump
Fig.10 turning off interface
Fig.12 Temperature setting interface for
The first time preset heating
1
2
4
11
To ensure that customers can use water heater properly and safely, we
seriously inform customers that you must contact the appointed professional
serving personnel for installing and service. For any improper installment, our
company will not burden any responsibility.
When the power supply is connected, pay attention that connecting lines of
pump are Inserted stably, and can not run without water. Before any
maintenance and repair of water heater, please make sure that you Cut off
the power Supply. Non-professional person are not allowed to adjust and
maintain water supply.
Before electrification please make sure that machines are full of water,
otherwise it will cause a system malfunction. The sockets are subject to
national standards and are connected to the ground reliably. It is prohibited
to use water heater without a reliable grounding.
The water heater is equipped with t . For
secure use, please do not change installment position personally. The
evacuating tube nozzle should be downwards vertically and are open to the
air so as to prohibit jamming the exit. A draining pipe is linked to the
evacuating tube nozzle and leads to the sewer opening. (the draining pipe is
otherwise sold)
Hot water with a temperature higher than 50 might result in scalding and
customers should mix hot water and cold water and then have a shower or
wash.
In cases when water heater is seriously soaked, it must be checked by
technical personnel ratified by our company before it is reused.
The hot water in water heater is not suitable for drinking. As a result of long-
term use, scale might be produced in the water tank. Meanwhile, the aging of
the water pipe can result in a change of water quality. Therefore, when you
wash rice and vegetables with water in the container, please wash them once
emperature and pressure valve
When collector equipment is installed, it can not be inversely placed.
Outdoor and indoor pipeline must use metal pipes.
Solar stage, a infusing liquid valve and expanding tank must install the
circulating water-exiting pipe of the tank.
Heat-preserving of pipelines must use specially designed materials by our
company.
ollector equipment should be installed facing south.
Evacuating opening of the system safety valve should be connected to the
release opening of sewage.
C
Particular warning
Particular warningParticular warning
Attentions in installment
Attentions in installmentAttentions in installment
Use method
sensor malfunction alarm of water-storing tank (E4), etc. When these
problems happen, the system will display malfunction code E1~E4. The
above malfunction protection is non-restorable and therefore, the system can
only normally run after malfunction is eliminated and the electricity is re-
connected.
3. Interface indication and instruction for operation
After the solar water heater center is installed, to confirm that the water-
storing tank is full of water and to check that each pipeline is connected
properly and not leaking. To check that the power supply of the water-storing
tank corresponds to the requirements and then to connect power supply.
4. Instruction for controller setting
A.Turning on/ turning off: the system is turned on directly and automatically
enters the working mode and conditions before power supply is cut off. The
first tacitly approved working mode of the system is the solar energy mode.
The four-number tube of the indication screen displays the clock. The five-
number tube under the screen respectively displays water temperature of
water-storing tank and the temperature of water-exiting. The indication
interface is displayed in Fig.9 and at this time, all the pressing keys are
effective. Then press power supply key and the system will be turned off and
enter the electricity saving mode. The indication interface is displayed in
Fig.10 and at this time, only power supply key is effective and other keys are
ineffective. The interface only displays water temperature of water-storing
tank and the temperature of water exiting of collector equipment. However,
when the system is turned off, the solar heating and malfunction alarm
protection are all working and only if the conditions for the running of the
water pump are satisfied, water pump will run at full speed. When malfunction
alarm appears, it will display malfunction code.
B. Selection of working mode: the system provides four working modes, and
customers can select any mode as the present working mode. When the
system is turned on, press the mode key, and the system will circularly
exchange in order of solar energy heating, simultaneous heating, preset
heating and intellectual heating. Meanwhile, the corresponding icon point
will be on. Press mode key to choose a certain mode and stop pressing mode
key for 2 seconds, then the system will automatically enter this mode.
C. Parameter setting in all modes: to press the setting key can set the
followingParameters: clock, preset time, heating temperature, and
temperature difference value of water pump running. The number tube in the
set parameter indicates glisteningly. To press the adjusting Key to
5
10
Attentions in installment
Attentions in installmentAttentions in installment
All parts of the whole system are not allowed to be disassempled personally,
otherwise the results should be burdened personally.
Solar stage should be far from strong interfering sources.
The length of pipeline between water-storing tank and collector equipment
must be less than 10 meters.
Sensor of collector equipment should be installed at the water exiting
meatus.
The exhaust valve should be installed vertically at the water exiting meatus
of collector equipment and its position in the pipeline should be kept the
highest. To screw loosely the exhaust cap after installment to make it
exhaust freely.
Pay attention the crossing corner of water entering and exiting meatus
should be connected and the bottom one is for water-entering and the top
one is for water-exiting in the installment of collector equipment with flat
board.
Installation
InstallationInstallation
Installment of solar water heater is composed by the following parts:
installment of collector equipment, installment of water-storing tank and
installment of solar stage. Installment of each part should be completed by
the professional installing personnel appointed by our company in order to
ensure good functioning of the system.
Installment of collector equipment
Collector equipment of solar water heater BRF2-150W,PJF2-150W is
installed with the method of oblique top. collector equipment is placed on the
southern rooftop of the house and there is no shelter ahead. All the four
corners of collector equipment are linked perfectly with steel wire rope. the
other end of the steel wire rope is fixed under eaves or on the wall with a bolt.
Pay attention that the steel wire rope is strained and the bolt is rivet firmly.
Take the installment of solar water heater of PJF2-150W as an example. For
the sketch map of installment, please see Fig.5.
Installment of the solar stage
Based on customers' requests, ascertain the solar stage installment
position. There is a hole behind the solar stage ,according to the place and
distance of the hole, to drill 2 holes deep 70mm, 9mm on the wall, use 2
small bolt to fix the solar stage pothook on the wall,then put the solar stage
Use method
solar energy heating mode. If the present water temperature is higher than
that set previously, this kind of heating can not start(Note: in this mode, the
solar energy heating is not influence)..
C.Preset heating: this function automatically works out the time needed to the
set temperature according to the default heating power (2.2KW), and then
ensures the time when water heater begins to heat. This mode can realize
both one-time preset and twice preset. You can choose either heating method
based on your practical life necessity. If you need one-time preset heating,
you just need to press the setting mode to set the time of the two presetting
as the same. If you need twice preset heating, you just need to set the two
times respectively. (Note: the setting order is irrelevant to the time set). The
preset time is subject to the clock time of the system. In cases when the
machine is turned on, press continually the mode key to enter the preset
heating mode. The green point in the working indication icon is on. Press the
mode key and you can set each preset time and their respective preset
temperature. The preset temperature scope is 30 -75 . Note: in this mode,
the solar energy heating is not influenced. If the preset temperature is
reached before the preset time, the system will automatically start electrical
heating each time the system drops 5 until the preset time is reached. If the
temperature has not reached the preset one after the preset time is reached,
then the system will delay at most half an hour for heating.
D.Intellectual heating: this function automatically classifies and analyzes the
latest seven-day bathing regularity and memorizes the period of time that
customers have a bath most frequently within the seven days. And it then
heats ahead according to the preset 65 before the first heating period
arrives the second day. In cases when the machine is turned on, press the
mode key continually to enter intellectual heating mode. The green point in
the working indication icon is on. When the electrical heating starts, the red
point in the icon glistens. And when the electrical heating is over, the green
point is constantly on. Press the setting mode and you can set the heating
temperature, whose scope is 30 -75 . Note: in this mode, the solar energy
heating is not concerned.
2. Introduction of other functions
A. The system has a function of electricity-loss memory and that of automatic
starting when electrified.
B. High temperature protection: in the process of the water pump running, when
the water temperature of water-storing tank exceeds the high-temperature
protection temperature (85 ) set by the system, the water pump will
automatically stop running and will display the malfunction code E2.
C. Malfunction protection: this system has circuit malfunction alarm (E1), high
temperature alarm (E2), sensor malfunction alarm of collector equipment (E3),
9
6
Installation
Installment of water-storing tank
Water storing tank is a standing tank. Based on customers' requests,
ascertain specific installment position, and place water-storing tank then
connect the tempreture and pressure valve,cold water-inlet,hot water-
outlet,please see Fig.1-Fig.2. based on the distance between solar stage
and tank, machining one corrugation pipe, and connect the circulating water-
exiting and the below water-inlet of the solar stage. Then connect the sensor
of tank and inside wire to the solar stage, Pay attention that the distance
between solar stage and tank should not be over 0.6m please see Fig.1-
Fig.2.
Connection of pipeline
To measure the distance between water-inlet of collector and the tee joint of
expanding tank, water-outlet of collector and circulating water-inlet of tank,
solar stage and circulating water-outlet of tank, To cut pipes according to the
measured size, to cover the heat preservation layer, and to connect water-
inlet of collector, the tee joint of expanding tank, water-outlet of collector and
circulating water-inlet of tank, as well as the solar stage and circulating
water-outlet of tank,please see Fig.1-Fig.2. Pay attention that the connection
of circulating pipeline should avoid the opposite alternative. The connection
of pipe parts should be proper and firm, and the heat preservation materials
should be covered perfectly. Pay attention that the probe of the sensor is
placed properly. Installment of pipeline should be artistic and neat.
Connection of Single direction valve
Fix the Single direction valve 1 on the cold water-inlet of tank,then connect
the Single direction valve1 to the water supply;Fix the Single direction valve2
Ò£¿ØÆ÷ʹÓüò½é
Use method
On the solar stage pothook. Pay attention that the place of the solar stage
muse be nicety(please see Fig.6), and power of water pump should be
adjusted to the third grade.
Note: To avoid to put other things on the solar stage. And to avoid that water
spatter the pump directly,or the result is serious.
Fig.5 Installment sketch map of PJF2-150W
Fig.6 Solar stage pothook fixing size(unit:mm)
L4(Double color)--- when the green point in the icon is on, it tells that the
system is in the intellectual heating mode. When the red light is glistening, it
tells that the system in electrical heating and when it reaches the mounted
temperature, the green point will be on constantly.
L5(Yellow)---when the character is on, it tells the temperature of water-
storing tank.
L6(Red)--- when the character is on, it tells the temperature of water-exiting
temperature of collector equipment.
ͼÈý ¼¯ÈÈÆ÷µÄ°²×°
Use methed
For the first use after installation, due to there's no water within the tank, first
the cold water inlet valve and mixing valve must be opened. Close the mixing
valve when water flows out continuously from the showerhead or other outlets
(the tank is full). Check connections are free of water leakage, and insert the
power plug.
1. introduction of basic working mode
A.Solar energy heating: this function adopts the temperature difference
between water-exiting temperature of collector equipment and that of water--
Storing tank to control the running of water pump. It transfers solar energy
absorbed by collector equipment to hot water in water-storing tank for storage.
In cases when the machine is turned on, press the mode key to enter the solar
energy heating mode (Note: the first time the system is electrified, this mode
can be entered). The green point is in the working indication icon is on in the
solar energy heating. Press the setting key and you can adjust the clock and
choose temperature difference value (10 or 15 , the default value is 15 )
of the water pump running. When the starting conditions for water pump are
reached, then the water-exiting temperature of collector equipment 20 .
Meanwhile, when temperature difference between water-exiting of collector
equipment and water in water-storing tank is higher than the set value (10
or 15 ), water pump will automatically start and run at full speed. When the
temperature difference is less than 4 , water pump will automatically stop.
B.Instant heating: in cases when the machine is turned on, press the mode key
to enter the instant heating mode. The green point in the working indication
icon of this heating is on. To automatically start electrical heating according to
the preset 65 of the system and the red point glistens. Press the setting
mode and you can set water temperature, whose scope is 30 -75 . When
the preset temperature is reached, the electrical heating will stop
automatically. The working mode will automatically leap from this mode to the
Introduction for the controller
L1L1 L2L2 L3L3 L4L4
L5L5
L6L6
SET
REG
ON/OFF
MODE
T-DISP
WT
HC
SOL
H
PRE
INT
Temperature Display of
the tank or collecter
Clock display and set
Fig.8 Indication board
7
Installation
8
Introduction for the controller
Installation
Pressure handle
Pressure relief vent
Fig.7 S
ketch map of tempreture
And pressure valve
On Outdoors circulating liquid-returning of collector,and the direction of
Single direction valve2 and circulating liquid-returning pipe must be
same,please see Fig1-Fig.2
Connection and Use of temperature and pressure valve
When the temperature rise, a little water will drip from pressure relief vent on
the temperature and pressure valve due to normal expansion. The vent shall
be installed downwards and always keep open to the air. Avoid being
blocked.
Note: If your water heater is not installed in a bathroom with sewage drain, it
is suggested you connect a drain hose (separately sold) to the temperature
and pressure valve. Connect one end of the hose to the temperature and
pressure valve vent and the other end to the sewage drain. The hose can be
cut short or extended as necessary. The hose shall be installed as inclined
downward.
Note: the mixing valve is separately sold,you can get it from the local
service,and contact the appointed professional serving personnel for
Connection of affusing liquid valve and
expanding tank
Fix the affusing liquid valve on the top water-
outlet of solar stage(the pipe of connection with
pump), affusing liquid valve is no direction
demand,but the room arond affusing liquid
valve should be big,as to affuse liquid
conveniencly. Fix a tee joint on the outlet of
the top hole of the tee joint should be connected to circulating water-outlet
pipe, ensure the place, to drill 2 holes 70mm deep, 9mm on the wall, use
two small bolt to fix the expanding tank on the wall with expanding tank
strap,please see Fig.1-Fig.2.
Note: affusing liquid valve and expanding tank should be connected to the
Corresponding pipe of circulating water-outlet of tank.
Connection of controlling equipment
Controlling equipment of the water heater is composed of power supply
board and indication board. Both are inside the solar stage.Open the shell of
solar stage , according to the electrical connection principle figure : connect
the L N of power supply line which connects heating element to the L N of
relay fan-out( the sign of N on the relay is corresponding to the N of power
supply line) , then the sensor of tank should be connecte to the power supply
board, and insert it tightly, Finally, press the power supply line tightly, install
again the solar stage cover,and to screw tightly the self-tapping screw.
To fill up the tank
To open water-exiting valve of hot water and to fill water into the tank,through
cold water meatus of tap water. To close water exiting valve of hot water until
the air is exhausted and water flows out continually. Meanwhile, to observe
whether the system leaks and to keep the cold water entrance open in the
process of use.
Affuse antifreeze
Screw down the cap of affusing liquid valve,close the big halt valve in the
middle of affusing liquid valve( note:when the handle of the valve and axes of
the valve are vertical, the valve is closed),open the other small halt valve,put
the liquid-exiting of the equipment to one affusing liquid hole,make sure the
flow direction of antifreeze and Single direction valve 2 are the same, and
the other affusing liquid hole connect the liquid-returning of the equipment,
start the liquid equipment, at the same time, observe the antifreeze untill
returning antifreeze is well-proportioned, and no air bladder.firstly close the
halt valve which connect the liquid-returning equipment, then close the the
halt valve which connect the liquid-exiting equipment,then open the big halt
valve in the middle of affusing liquid valve, remove the equipment.
Note: after affusing the antifreeze, put the 3/4 fiber spacer to the cap of the
affusing liquid valve, and screw tightly the the cap of the affusing liquid valve,
to avoid the antifreeze flowing from the tank.
L1--L4 indicator lights respectively represent the
four modes of the system working, among which
L2--L4 lights are all double color , L5--L6 lights
respectively represent the t
For details as follows:
L1(green)---when the green light is on, it indicates
that the system is woking on the solar energy
heating mode.
L2(Double colors)---when the green light is on, it
indicates that the system is working on the instant
heating mode. When the red light is glittering, it
emperatures of the
upper tank and outlet of the collector.
Introduction for the controller
Indicates heating up.
L3(Double colors)---when the green light is on, it indicates that the system is
working on the preset heating mode. When the red light is glittering, it
indicates that the system is heating up ,and will be green as it reaches the
preseted temperature, the green point will be on constantly.
Installation
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Haier Sea Elephant BRF2-150W Manuale utente
- Tipo
- Manuale utente
- Questo manuale è adatto anche per
in altre lingue
Documenti correlati
Altri documenti
-
Panasonic PAWDHWM300ZE Istruzioni per l'uso
-
Aquarea PAW-DHWM 80-120 ZNT Istruzioni per l'uso
-
Dometic TRT120E Istruzioni per l'uso
-
Sime Murelle Equipe 100 150 Box ErP Manuale del proprietario
-
-
-
Olimpia Splendid Sherpa AQUADUE OS-CETNH48EI Manuale del proprietario
-
Olimpia Splendid Sherpa AQUADUE S2 Guida d'installazione
-
Olimpia Splendid SHERPA Tower S2 SMALL Guida d'installazione
-
Olimpia Splendid Sherpa S2 Manuale d'installazione
