Sime Murelle Equipe 220 550 Box ErP Manuale del proprietario

199839

ENSURE THAT THESE

INSTRUCTIONS ARE LEFT

FOR THE USER AFTER

COMPLETION OF THE

BENCHMARK SECTION

PLEASE READ THE

IMPORTANT NOTICE

WITHIN THIS GUIDE

REGARDING YOUR BOILER

WARRANTY

USER, INSTALLATION AND SERVICING INSTRUCTIONS

MURELLE EQUIPE

220-330-440-550 BOX ErP

Cod. 6328549 - 05/2019

ORIGINAL INSTRUCTIONS

This boiler may require 2 or more operatives to move it into its installation site, remove it from its packaging and

during movement into its installation location. Manoeuvring the boiler may include the use of a sack truck and

involve lifting pushing and pulling.

Caution should be exercised during these operations.

Operatives should be knowledgeable in handling techniques when performing these tasks and the following

precautions should be considered:

– Grip the boiler at the base

– Be physically capable

– Use personal protective equipment as appropriate e.g. gloves, safety footwear.

During all manoeuvres and handling actions, every attempt should be made to ensure the following unless

unavoidable and/or the weight is light.

– Keep back straight

– Avoid twisting at the waist

– Always grip with the palm of the hand

– Keep load as close to the body as possible

– Always use assistance

WARNING

Caution should be exercised when performing any work on this appliance.

Protective gloves and safety glasses are recommended.

– Avoid direct contact with sharp edges.

– Avoid contact with any hot surfaces.

NOTICE

Please be aware that due to the wet testing of the appliance, there may some residual water in the hydraulic circuit.

– Protect any surfaces, carpets or floorings.

– Use a suitable container to catch any water that escape when removing the protective caps from the connections.

SAFE HANDLING

CONFORMITY

Our Company declares that MURELLE EQUIPE 220-330-440-550 BOX ErP boilers comply with the essential requi-

rements of the following directives:

- Boiler Efﬁciency Directive 92/42/EEC

- Gas Appliances Directive 2009/142/EC

- Electromagnetic Compatibility Directive 2014/30/EU

- Low Voltage Directive 2014/35/EU

- Ecodesign Directive 2009/125/EC

- Regulation (EU) N. 813/2013 - 811/2013

All descriptions and illustrations provided in this manual have been carefully prepared but we reserve the right to make

changes and improvements in our products that may affect the accuracy of the information contained in this manual.

Important Information

IT IS A STATUTORY REQUIREMENT THAT ALL GAS APPLIANCES ARE INSTALLED BY COMPETENT PERSONS,

IN ACCORDANCE WITH THE GAS SAFETY (INSTALLATION AND USE) REGULATIONS (CURRENT EDITION).

The manufacturer’s instructions must not be taken as overriding any statutory requirements, and failure

to comply with these regulations may lead to prosecution.

No modifications to the appliance should be made unless they are fully approved by the manufacturer.

GAS LEAKS: DO NOT OPERATE ANY ELECTRICAL SWITCH, OR USE A NAKED FLAME. TURN OFF THE GAS

SUPPLY AND VENTILATE THE AREA BY OPENING DOORS AND WINDOWS contact the gas emergency ser-

vice on 0800111999.

CONTENTS

1 DEVICE DESCRIPTION ..................................................................... pag. 4

2 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pag. 10

3 CHARACTERISTICS ....................................................................... pag. 21

4 COMMISSIONIMG, USE AND MAINTENANCE .................................................. pag. 28

5 FAULT FINDING .......................................................................... pag. 38

6 APPENDIX 1 ............................................................................. pag. 39

USER INSTRUCTIONS ..................................................................... pag. 53

PRODUCT DETAILS ........................................................................................................................................ pag. 55

ANNEX AA.1 ................................................................................................................................................... pag. 56

Please refer to commissioning instructions for filling in the checklist at the back of this installation guide.

Note: All Gas Safe registered installers carry a ID Card.

You can check your installer is Gas Safe Registered by calling 0800 408 5577

IMPORTANT

Prior to switching on the boiler for the first time, check the following:

– Make sure that there are no liquids or inflammable materials in the immediate vicinity of the boiler.

– Make sure that the electrical connections have been made correctly and that the earth wire is connected

to a good earthing system.

– Ensure that tightness and let by test have been conducted, including the internal gas pipe work.

– Make sure that the boiler is set for operation for the type of gas supplied.

– Check that the flue pipe for the outlet of the products of the combustion is unobstructed and has been

properly installed.

– Make sure that any isolation valves are open.

– Make sure that the system is filled with water and is thoroughly vented.

– Check that the circulating pump is not jammed.

– Purge the gas supply pipe work.

– Ensure that the checklist is filled in when the commissioning has been completed.

4

1.1 INTRODUCTION

“MURELLE EQUIPE 220-330-440-550

BOX ErP” are pre-mixed condensation

heating modules intended only for heat-

ing, designed to work in sequence/cas-

cade.

1 DEVICE DESCRIPTION

1.2 DIMENSIONS MODULES

1.2.1 “MURELLEEQUIPE 220 BOX ErP” (fig. 1)

Fig. 1

FIXTURES

M System supply (Flange PN6-DN100)

R System return (Flange PN6-DN100)

G Gas (Flange PN6-DN50)

S3 Condensation drain ø 40

630

260

380

390

M

R

307

777

648

1600

2010

90

180

156

396

790

567

272

S3

G

90

180

156

396

790

567

272

S3

G

M

307

777

R

260

380

1100

648

1600

2010

470

390

MURELLE EQUIPE 110 BOX

MURELLE EQUIPE 220 BOX ErP

NOTE: The installation must incorporate a hydraulic separator or plate heat exchanger. The hydraulic separator available

from Sime Ltd is supplied with modules in a kit code 8101552 and the tubes connecting the hydraulic separator in the kit

code 8101532. It can be assembled on the left-hand side by moving the system supply/return manifold blind flanges.

5

1.2.2 “MURELLE EQUIPE 330 BOX ErP” (fig. 1/a)

90

180

156

396

790

567

272

S3

G

MURELLE EQUIPE 330 BOX ErP

648

1600

2010

390

630

470

1730

380

260

307

777

M

R

1100 630

Fig. 1/a

FIXTURES

M System supply (Flange PN6-DN100)

R System return (Flange PN6-DN100)

G Gas (Flange PN6-DN50)

S3 Condensation drain ø 40

NOTE: The installation must incorporate a hydraulic separator or plate heat exchanger. The hydraulic separator available

from Sime Ltd is supplied with modules in a kit code 8101552 and the tubes connecting the hydraulic separator in the kit

code 8101532. It can be assembled on the left-hand side by moving the system supply/return manifold blind flanges.

6

1.2.3 “MURELLE EQUIPE 440-550 BOX ErP” (fig. 1/b)

180

790

396

156

567

90

272

562

1197

S3

M

R

G

1600

2010

2830

590

500

390

630

470

630

470

635

562

MURELLE EQUIPE 440 BOX ErP

180

790

396

156

567

90

272

562

1197

S3

M

R

G

1600

2010

2200

590

500

390

470

630

470

635

562

MURELLE EQUIPE 550 BOX ErP

Fig. 1/b

FIXTURES

M System supply (Flange PN6-DN100)

R System return (Flange PN6-DN100)

G Gas (Flange PN6-DN50)

S3 Condensation drain ø 40

NOTE: The installation must incorporate a hydraulic separator or plate heat exchanger. The hydraulic separator

available from Sime Ltd is supplied with modules in a kit code 8101553 and the tubes connecting the hydraulic

separator in the kit code 8101533. It can be assembled on the left-hand side by moving the system supply/return

manifold blind flanges.

7

1.3 TECHNICAL SPECIFICATIONS

MURELLE EQUIPE 220 BOX ErP 330 BOX ErP 440 BOX ErP 550 BOX ErP

Generators with a heat output kW 105.4 n° 2 3 4 5

Heat output

Nominal (80-60°C) (Pn max) kW 210.8 316.2 421.6 527.0

Nominal (50-30°C) (Pn max) kW 225.2 337.8 454.0 563.0

Minimum (80-60°C) (Pn min) kW 20.8 20.8 20.8 20.8

Minimum (50-30°C) (Pn min) kW 23.2 23.2 23.2 23.2

Heat input (*)

Nominal (Qn max - Qnw max) kW 216 324 432 540

Minimum (Qn min - Qnw min) kW 21.6 21.6 21.6 21.6

Min-max operating yield (80-60°C) % 96.4 - 97.6 96.4 - 97.6 96.4 - 97.6 96.4 - 97.6

Min-max operating yield (50-30°C) % 107.4 - 104.2 107.4 - 104.2 107.4 - 104.2 107.4 - 104.2

Operating yield at 30% (40-30°C) % 105.4 105.4 105.4 105.4

Losses after shutdown to 50°C (EN 15502) W 498 747 996 1245

Feeding tension V-Hz 230-50 230-50 230-50 230-50

Absorbed power consumption (Qn max) W 516 774 1032 1290

Absorbed power consumption (Qn min) W 134 138 142 146

Absorbed power consumption C.H. pump W 260 (130 x 2) 390 (130 x 3) 520 (130 x 4) 650 (130 x 5)

Electrical protection grade IPX4D IPX4D IPX4D IPX4D

Energy efficiency

Seasonal energy efficiency class of the heating system A A A A

Seasonal energy efficiency of the heating system % 90 91 91 91

Sound power of the heating system dB (A) --- --- --- ---

Single module temperature regulation °C 20/80 20/80 20/80 20/80

Water content modules l 36.3 55.9 72.6 92.2

Max operating pressure (PMS) bar (kPa) 5 (490) 5 (490) 5 (490) 5 (490)

Max operating temperature (T max) °C 85 85 85 85

Exhaust temperature at max flow rate (80-60°C) °C 64 64 64 64

Exhaust temperature at min flow rate (80-60°C) °C 51 51 51 51

Exhaust temperature at max flow rate (50-30°C) °C 45 45 45 45

Exhaust temperature at min flow rate (50-30°C) °C 40 40 40 40

Smokes flow min/max g/s 10.28 / 103.34 10.28 / 155.00 10.28 / 206.67 10.28 / 258.34

CO

2 at max/min flow rate G20 % 9.0 / 9.0 9.0 / 9.0 9.0 / 9.0 9.0 / 9.0

CO2 at max/min flow rate G31 % 10.2 / 10.2 10.2 / 10.2 10.2 / 10.2 10.2 / 10.2

NOx measured (EN15502 - 1:2015) mg/kWh 22 22 22 22

Max. output pressure fumes manifold Pa 375 375 375 375

Max. pressure independent fumes Pa 428 428 428 428

PIN number 1312CM5621 1312CM5621 1312CM5621 1312CM5621

Category II2H3P II2H3P II2H3P II2H3P

Type B23-B53-B23P-B53P B23-B53-B23P-B53P B23-B53-B23P-B53P B23-B53-B23P-B53P

NOx emission class (EN15502 - 1:2015) 6 (‹ 56 mg/kWh) 6 (‹ 56 mg/kWh) 6 (‹ 56 mg/kWh) 6 (‹ 56 mg/kWh)

Weight when empty kg 380 615 760 995

Gas and nozzle pressure

Supply pressure G20 mbar (kPa) 20 (1.96) 20 (1.96) 20 (1.96) 20 (1.96)

Supply pressure G31 mbar (kPa) 37 (3.63) 37 (3.63) 37 (3.63) 37 (3.63)

Number of nozzles n° 2 3 4 5

Nozzle diameter G20 ø 17.2 17.2 17.2 17.2

Nozzle diameter G31 ø 9.8 9.8 9.8 9.8

Consumption at nominal output G20 m

3

/h 22.84 34.26 45.68 57.10

Consumption at minimum output G20 m

3

/h 2.28 2.28 2.28 2.28

Consumption at nominal output G31 kg/h 16.76 25.14 33.52 41.90

Consumption at minimum output G31 kg/h 1.68 1.68 1.68 1.68

(*) Heat input of the heating system measured using lower heating value (LHV)

8

1.4 OPERATING DIAGRAM (fig. 2)

M

R

1

2

25

23

22

G

26

12

16

14

15

18

24

27

6

8

10

9

11

17

S3

5

30

3

Fig. 2

KEY

1 Cascade delivery supply probe (SMC)

2 Hydraulic compensator

3 Antifreeze siphon sensor (SB/SA)

4 Safety valve 5 bar

5 Condensation drain siphon

6 Gas valve

7 8 litre expansion tank

8 Fan

9 Heating supply probe (SM)

10 Safety thermostat 100°C

11 Exhaust temperature probe (SF)

12 Heat exchanger

13 Gas isolation valve

14 Heating return probe (SR)

15 Water pressure transducer

16 Air release vent

17 Non return valve

18 Pump high efficiency

19 3-way isolation/drain valve

20 Isolation valve

21 Single module drain

FIXTURES

M System supply

R System return

G Gas

S3 Condensation drain

9

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

Gas

1.5 MAIN COMPONENTS (fig. 3)

Fig. 3

Code 8117080

Model MURELLE EQUIPE 220 BOX ErP

Serial n. 9999999999

PAR 1 = 8 (G20) / 16 (G31)

PAR 2 = 9

KEY

1 System return manifold

2 Gas isolation valve

3 System supply manifold

4 Gas valve

5 Fan

6 Ignition electrode

7 Primary exchanger

8 Ignition transformer

9 Control panel

10 Heating return probe (SR)

11 Heating supply probe (SM)

12 Safety thermostat 100°C

13 Ionisation electrode

14 Pump high efficiency

15 Isolation valve

16 3-way isolation/drain valve

17 Gas manifold

MODEL

SERIAL NUMBER

YEAR OF CONSTRUCTION

WATER CONTENT IN BOILER

HEAT INPUT MAX

HEAT OUTPUT MAX (80-60°C)

HEAT OUTPUT MAX (50-30°C)

MAX OPERATING PRESSURE

CONTENTS D.H.W.

HEAT INPUT MAX D.H.W.

MAX OPERATING PRESSURE D.H.W.

D.H.W. FLOW RATE

POWER SUPPLY

MAX POWER ABSORBED

COUNTRIES OF DESTINATION

CATEGORY

TYPE

CODE

DIRECTIVE OF REFERENCE

PIN NUMBER

HEAT INPUT MIN

HEAT OUTPUT MIN (80-60°C)

HEAT OUTPUT MIN (50-30°C)

MAX OPERATING PRESSURE

HEAT INPUT MIN D.H.W.

MAX OPERATING PRESSURE D.H.W.

ELECTRICAL PROTECTION GRADE

NOx CLASS

CODE GAS COUNCIL NUMBER (UK)

CERTIFICATION WRAS (UK)

TYPE OF GAS

GAS SUPPLY PRESSURE

CLASSIFICATIONS

1.6 TECHNICAL DATA PLATE (fig. 3/a)

Fig. 3/a

10

The unit is suitable for external instal-

lation in a fixed location. It must be

installed by qualified engineers in

compliance with all instructions con-

tained in this manual. Furthermore,

the installation must be in accordance

with current standards and regula-

tions

.

2.1 SUPPLY (fig. 4)

“MURELLE EQUIPE 110 BOX ErP” heat

modules are available in single or double

generators and can be coupled together

to a maximum of 5 generators. The cabi-

net is pre painted, zinc coated. They are

supplied complete with flow and return,

gas and condensate manifolds, external

temperature probe kit, cascade supply

and RS-485 code 8092250 board connec-

tion cable. Available separately:

– Connection kit for the hydraulic sepa-

rator

code 8101532 for

modules “220-

330 BOX ErP” and code 8101533

for

modules “440-550 BOX ErP”

– Double box (size: 1100 x 790 x 1600)

for hydraulic separator code 8101527

– Hydraulic separator kit code 8101552

for modules “220-330 BOX ErP” and

code 8101553 for modules “440-550

BOX ErP”

– Polypropylene exhaust manifold kit for

indoor installation (purposely treated to

resist weathering when installed out-

doors):

code 8102530 for “220 BOX ErP”

mod-

ule

code 8102531 for “330 BOX ErP”

mod-

ule

code 8102532 for “440 BOX ErP”

mod-

ule

code 8102533 for “550 BOX ErP”

mod-

ule

– Exhaust terminal code 8089530 (1 per

generator) for outdoor installations.

To electrically connect the modules and

to assemble the exhaust for indoor or

outdoor installations, see points 2.6, 2.7

and 2.10 in this manual.

2.2 INSTALLATION

2.2.1 Indoors

“MURELLE EQUIPE 220-330-440-550

BOX ErP” heat modules can be installed

in boiler rooms whose size and require-

ments meet current regulations.

VENTILATION

The following is provide for your guid-

ance only, and assumes the ventila-

tion air is taken directly from outside.

The sizes of the vents may need to be

increased in respect of other appliances

installed in the same area, and seasonal

use. Take care that the position of low

2 INSTALLATION

1600

470

308

1100

790

396

635

562

BOX CONTENITORE DOPPIO PER COMPENSATORE

IDRAULICO cod. 8101527

PER MURELLE EQUIPE 220 - 330 BOX

1100

16 00

790

BOX CONTENITORE DOPPIO PER COMPENSATORE

IDRAULICO cod. 8101527

PER MURELLE EQUIPE 440 - 550 - 660 BOX

Fig. 4

NOTE: position the blanking covers according to the hydraulic separator used.

DOUBLE BOX FOR HYDRAULIC SEPARATOR

AND CONNECTIONS code 8101527

FOR MURELLE EQUIPE 220-330 BOX ErP

DOUBLE BOX FOR HYDRAULIC SEPARATOR

AND CONNECTIONS code 8101527

FOR MURELLE EQUIPE 440-550 BOX ErP

11

level vents would not subject to adverse

weather conditions, ie flooding.

Ventilation requirements for Murelle

HE 110 R ErP boilers and cascade sys-

tems.

BS6644 has a requirement that the tem-

peratures in a room or compartment do

not exceed certain levels:

25°C at floor level(0-100mm)

32°C at mid level (1.5M above the floor

level)

40°C at ceiling level (0-100mm from ceil-

ing)

Installed as a class B appliance (open

flued).

Installed in a room

High level (within 15% of the room

height from ceiling) - 2cm²/KW of net

heat input

Low level (low as possible within 1

metre from floor natural gas, 250mm

LPG)– 4cm²/KW of net heat input

A single generator (120KW net input)

would require 240cm² at high level and

480cm² at low level.

Installed in a compartment or enclosure

High level (within 15% of the room

height from ceiling) - 5cm²/KW of net

heat input

Low level (low as possible within 1

metre from floor natural gas, 250mm

LPG) – 10cm²/KW of net heat input.

A single generator (120KW net input)

would require 600cm² at high level and

1200cm² at low level.

2.2.2 Outdoors

“MURELLE EQUIPE 220-330-440-

550 BOX ErP” heat modules can also

be installed outdoors with the specific

exhaust for single module code 8089530.

2.3 SYSTEM REQUIREMENTS

The heating system should be flushed

prior to the connection of the heating

modules. The system should be treated

in accordance with BS 7593. Sime Ltd

recommend only the use of Fernox prod-

ucts for the flushing and final treatment

of the system water. This is particularly

important in hard water areas.

It is recommended that the inhibitor

concentration is checked at installation,

system modification and at every service

in accordance with the manufacturers

instructions. Test kits are available from

inhibitor stockist.

WARNING: Failure to clean the heat

system or add an adequate inhibitor

invalidates the device’s warranty.

Gas connections must be made in

accordance with current standards and

regulations. When dimensioning gas

pipes from the meter to the module,

both capacity volume (consumption) in

m

3

/h and gas density must be taken into

account.

System pipe sections must be able to

guarantee sufficient supply to cover max-

imum demand, limiting pressure loss

between the meter and any utility device

no greater than 1.0 mbar for second fam-

ily gas (natural gas).

A sticker inside the module includes

identification and gas type data specific

to the module.

2.3.1 Condensation drain connection

The condensate

drain must be con-

nected to the civil drain by a pipe with

minimum 5 mm per meter gradient for

condensation collection.

Only stainless steel or plastic pipes are

suitable to convey condensate.

Fig. 5

STAFFA TELAIO

CALDAIA

G

M

R

Pmin

Pmax

12

2.3.2 Filter on the gas pipe

The gas valve

on each generator

is sup-

plied ex factory with an inlet filter, which,

however, is not adequate to entrap all

the impurities in the gas or in gas main

pipes.

To prevent malfunctioning of the valve,

or in certain cases even to cut out the

safety device with which the valve is

equipped, install an adequate filter on

the gas pipe.

2.5 FILLING THE SYSTEM

Cold system filling pressure must be 1

bar. The system must be filled slowly

so that air bubbles are released through

the specific escapes.

2.6 EXHAUST

FOR OUTDOOR

INSTALLATION

(fig. 5)

The exhaust terminal for single module

code 8089530 is required for this type of

installation.

For separately supplied accessory

assembly see fig. 5.

390

ø 125

180

MURELLE 110 BOX ErP

con kit collettore fumi

cod. 8102510

460

ø 200

498

ø 200

MURELLE EQUIPE 220 BOX ErP

con kit collettore fumi

cod. 8102530

MURELLE EQUIPE 330 BOX ErP

con kit collettore fumi

cod. 8102531

Fig. 6

MURELLE EQUIPE 220 BOX ErP

exhaust manifold kit

code 8102530

MURELLE EQUIPE 330 BOX ErP

exhaust manifold kit

code 8102531

13

527

ø 200

MURELLE EQUIPE 440 BOX ErP

con kit collettore fumi

cod. 8102532

MURELLE EQUIPE 440 BOX ErP

(con box contenitore per separatore idraulico

e kit sicurezze ISPSEL cod. 8101527)

1100

1600

180

Fig. 6/a

MURELLE EQUIPE 440 BOX ErP

exhaust manifold kit

code 8102532

MURELLE EQUIPE 440 BOX ErP

(with box container for hydraulic separator

code 8101527)

14

180

ø 200

565

1100

1600

MURELLE EQUIPE 550 BOX ErP

(con box contenitore per separatore idraulico

e kit sicurezze ISPSEL cod. 8101527)

MURELLE EQUIPE 550 BOX ErP

con kit collettore fumi

cod. 8102533

Fig. 6/b

MURELLE EQUIPE 550 BOX ErP

exhaust manifold kit

code 8102533

MURELLE EQUIPE 550 BOX ErP

(with box container for hydraulic separator

code 8101527)

15

2.7 INDOOR INSTALLATION

EXHAUST KIT (fig. 6 - 6/a - 6/b)

Refer to fig. 6 and 6/a-b for this type

of installation. The indicated solutions

have the exhaust manifold (available

separately) positioned on the module’s

to right.

It is however possible to move the

exhaust of the left by simply rotating the

manifold 180°.

NOTE: The kits are purposely treat-

ed also to resist weathering when

installed outdoors.

In these cases the compensator and

safety device must be inserted in the

double container box code 8101527.

2.8 TUBES CONNECTING THE

HYDRAULIC SEPARATOR KIT

(fig. 7 - fig. 7/a)

Tubes connecting the hydraulic separa-

tor kit code 8101532 supplied as option

for “MURELLE EQUIPE 220-330 BOX

ErP” models it is formed (fig. 7):

– System supply flanged section code

6291968

– System return flanged section code

6291968

– Gaskets, nuts and fastening screws

M16

– Expansion vessel 8 liters code

6245108 (Preload pressure 1.5 bar

– Maximum pressure 10 bar) and con-

nection pipe code 6227661

WARNING: In models “220-330 BOX ErP”

the tubes connecting hydraulic separator

kit can be inserted in a specific protective

Fig. 7

Fig. 7/a

16

box code 8101527 supplied separately

(see fig 4).

Tubes connecting the hydraulic separa-

tor kit code 8101533 supplied as option

for “MURELLE EQUIPE 440-550 BOX

ErP” models it is formed (fig. 7/a):

– System supply flanged section code

6291969

– System return flanged section code

6291971

– Gaskets, nuts and fastening screws

M16

– Expansion vessel 8 liters code

6245108 (Preload pressure 1.5 bar

– Maximum pressure 10 bar) and con-

nection pipe code 6227661.

WARNING: In models “440-550 BOX ErP”

the tubes connecting hydraulic separator

kit can be inserted in a specific protective

box code 8101527 supplied separately

(see fig. 4).

2.9 RS-485 BOARD (fig. 8)

Each generator is supplied with the RS-

485 board which allows you to manage

the boilers in sequence/cascade (see

fig 8).

The board is placed on the back of the

control panel.

2.9.1 MODBUS

mode

This mode allows for MODBUS commu-

nication of at least two boilers in cascade

and is performed by requesting MODBUS

INTERFACE KIT code 8092278.

x 2

CN10

CHIAVE

POLARIZATION

Fig. 8

17

2.10 SYSTEM AVAILABLE HEAD

(fig. 9)

The head available of the generator sup-

ply/return manifolds vs. the flow rate is

shown on the chart of figure 9.

2.10.1 Load loss hydraulic separator

Hydraulic separator load losses are indi-

cated in the diagram in fig. 9.

WARNING: The hydraulic separator can

be inserted in a specific protective box

code 8101527 supplied separately.

2.10.2 Hydraulic separator

“220-330 BOX ErP” (fig. 10)

The hydraulic separator is supplied sepa-

rately in a kit code 8101552 complete with

gaskets, nuts and fastening screws (figure

10).

2.10.3 Hydraulic separator

“440-550 BOX ErP” (fig. 10/a)

The hydraulic separator is supplied

separately in a kit code 8101553 com-

plete with gaskets, nuts and fastening

screws (figure 10/a). The plant is sup-

plied with three supporting “C” brackets

that should be used only to rest the com-

pensator onto the ground.

C

Fig. 10

400

500

600

700

PORTATA (m

3

/h)

51015

0

100

200

300

∆p (mbar)

Murelle Equipe

800

20

110 BOX ErP - 92.5 R ErP

220 - 220 BOX ErP

330 - 330 BOX ErP / 280 - 280 BOX ErP

440 - 440 BOX ErP / 370 - 370 BOX ErP

550 - 550 BOX ErP / 460 - 460 BOX ErP

660 - 660 BOX ErP

Fig. 9

CAPACITY (m

3

/h)

SYSTEM AVAILABLE HEAD

LOAD LOSS HYDRAULIC SEPARATOR

100

150

5

PORTATA (m

3

/h)

10 15 20 25 30

0

50

∆p (mbar)

35

40

45

200

CAPACITY (m

3

/h)

C

Fig. 10/a

18

TA2 (24 VRAC)

TA1 (24 VRAC)

SB/SA

(5 VDC)

SE (5 VDC)

TS (24 VDC)

SM (5 VDC)

SF (5 VDC)

SR (5 VDC)

RS-485 (24 VAC)

OP (24 VAC)

TPA

V

EV 1-2

TFU

CR

0...10 VDC

TRA

EA

ER

PI

2.11 ELECTRICAL

CONNECTIONS

Each module is supplied with a power

cord which, if replacement is required,

it must be replaced with one of similar

type and dimensions.

230V – 50 Hz single phase voltage is

required using a fuse protected main

switch with at least 3 mm. between con-

tacts. Observe the L – N polarity and

grounding connection. Each generator

should be fused at 3 A.

NOTE: Sime declines all responsibility

for injury or damage to persons, ani-

mals or property resulting from the

failure to provide for proper earthing of

the appliance.

2.11.1 Wiring diagram single generator (fig. 11)

KEY

F1-2 Fuse (4 AT)

TRA Ignition transformer

PI Pump high efficiency

V Fan

EA Ignition electrode

ER Ionisation electrode

EV1-2 Gas valve coil

TS Safety thermostat

SF Exhaust temperature sensor

TFU Thermal fuse

SM Flow temperature sensor

SR Return temperature sensor

TPA Pressure transducer

JP1 Selection TA2 or 0-10 VDC

TA1 Zone 1 environment thermostat

TA2 Zone 2 environment thermostat

SB/SA Antifreeze siphon sensor

CR Remote control SIME HOME (optional)

SE External sensor (optional)

OP Programming clock (optional)

AR Remote alarm

VZ Zone valve

AUX Auxiliary connection

RS-485 CASCADE board

NOTE: Connect TA1 to the clamps 7-8 after having

removed the bridge.

CONNECTOR SPARE

PART CODES:

CN1 code 6319176

CN2 code 6319178

CN3 code 6319174

CN4 code 6316203

CN5 code 6316200

CN6 code 6316202

CN7 code 6316204

CN9 code 6316201

CN10 code 6319165

CN12 code 6319177

CN13 code 6319175

CN14 code 6293583

Fig. 11

For BMS (0-10v dc) operation:

- Remove the jumper JP1 and ensure that TA1 link is fitted

- Connect the positive signal at terminal 10 of CN6

- Connect the negative signal at terminal 4 of the CN4.

19

Pmin

Pma

x

TS

Kit sicurezze

ISPSEL

RS-485

RS-485 RS-485

RS-485

SE

SMC

(MASTER)

(SLAVE 2)

(SLAVE 3)

(SLAVE 4)

(SLAVE 1)

RS-485

(SLAVE 5)

Schema elettrico MURELLE EQUIPE 660

Fig. 11/a

2.11.2 Electrical connection of generators in sequence/cascade (fig. 11/a)

KEY

L Line

N Neutral

SE External sensor

SMC Cascade supply probe

RS-485 Cascade management board

NOTICE: The external temperature probe (SE) must be connected to the

MASTER generator and the cascade supply probe (SMC) to the SLAVE 1 gen-

erator.

The SE, SMC probes and the RS-485 board connection cable are supplied

together with the modules in the probe kit code 8092250.

The RS-485 board for management in sequence/cascade

is placed at the rear of the control panel of each individual

generator as shown in the figure.

CONFIGURATION OF CASCADE PARAMETERS

Sequence/cascade installations must have the following

INST parameter set on all connected generators:

PAR 15 = 0 for the first generator (MASTER)

1 .... 7 for the other generators (SLAVE)

(Avoid assigning the same number to SLAVE

generators)

Set the following INST parameter if polypropylene smoke

collectors with a clapet valve are used in sequence/cascade

installations:

PAR 1 = 8 (for NATURAL GAS generators)

16 (for PROPANE generators)

To access the INST parameters, see point 3.3.

In addition, when the number of connected generators

in cascade is more than two, parameter OEM A1 of the

MASTER generator must be configured as well.

To access the OEM parameters press simultaneously the

buttons (

5

3

1

2

4

and

5

3

1

2

4

) for 2 seconds.

Having entered the INST level, press (

5

3

1

2

4

and

5

3

1

2

4

) simultane-

ously for another 2 seconds. At this point insert the access

code formed by this sequence of INSTALLATOR BUTTONS:

“ + / - / < / > / < “.

Set the parameter:

PAR A1 = Number of cascade generators (3 ... 8)

x 2

CN10

CHIAVE

POLARIZATION

20

2.11.3 Room Thermostat and/or Timer

(clean contact)

The heating demand can be controlled

by a thermostat and/or timer (TA) con-

nected to CN6 terminals 7-8 (see fig

11), after having removed the existing

bridge. The control being used must be

of a class conforming to the standard EN

607301 (clean electrical contact).

2.11.4 Remote control SIME HOME

connection (optional)

The heating demand can be controlled

by use of remote control unit SIME

HOME (code 8092281)

The remote control unit allows for com-

plete control.

The generator will display CR.

For installation and use of the control

follow the instructions in the package.

NOTE, Ensure PAR 10 set to 1 (PAR 10

= 1)

2.11.5 External Sensor (8094101)

An external sensor (code 8091401) can

be connected, which can automatically

regulate the flow temperature value of

the cascade delivery according to the

external temperature.

For installation follow the instructions

in the package. It is possible to make

corrections to the values by adjustment

of PAR 11.

2.11.7 Heat Demand by 230v

The heat demand can be controlled by

230v applied to terminal 14 of CN7, and

removal of the bridge on CN6 terminals

7 & 8.

2.11.6 BMS (Building Management

Systems)

The cascade of generators can be con-

trolled by a BMS signal, and should be

connected as shown in fig 11.

Set PAR 14 according to the maximum

(10v) flow temperature required.

La pagina si sta caricando...

Sime Murelle Equipe 220 550 Box ErP Manuale del proprietario

Sime Murelle Equipe 220 550 Box ErP Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti