ProLights PIXIEBEAM Manuale utente

USER MANUAL

MANUALE UTENTE

PIXIE BEAM

BEAM MOVING HEAD

EN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.003-03/18

1

PIXIE BEAM

Packing content

• PIXIE BEAM

• Mount bracket

• Power supply cable and signal cable

• Safety rope

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 Slave Receive mode

3. 5 Operation in automatic mode

3. 6 Music mode

3. 7 Sensitivity microphone

3. 8 Linking

3. 9 DMX mode

3. 10 DMX conguration

3. 11 DMX addressing

3. 12 Connection of the DMX line

3. 13 Construction of the DMX termination

3. 14 DMX control

3. 15 Fixture settings

3. 16 Lamp settings

3. 17 Display settings

3. 18 Fixture information

3. 19 Reset functions

3. 20 Special functions

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Trouble shooting

2

3

5

6

7

8

9

10

12

13

16

17

19

20

PIXIE BEAM

2

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places wet;

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 45°C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• For inside use only. Not designed for outside use.

• The minimum distance between the xture and surrounding walls must be more than 50 cm and the

air vents at the housing must not be covered in any case.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• The maximum temperature that can be reached on the external surface of the tting, in a thermally

steady state, is high. After power o, please cool down over 15 minutes.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

3

PIXIE BEAM

- 1 - INTRODUCTION

1.1 DESCRIPTION

PIXIEBEAM is a fast, bright and compact moving LED beam luminaire. Some looks are all about scale, and

the Pixiebeam takes this idea to a dierent level featuring incredible speed and innite rotation of both

pan and tilt.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 60W RGBW Osram Ostar LED

• Lux: 11120lux @3m Full

• Source Life Expectancy: >50.000 h

OPTICS

• Beam Angle: 4,5°

• Lens Diameter: 100mm

COLOR SYSTEM

• Color Mixing: RGBW/FC

• CTC: CTC control through independent DMX channel

• White Presets: 2000~8000K

• Color Wheel: Virtual color wheel with presets

BODY

• Pan Angle: with 360° continuous rotation

• Tilt Angle: with 360° continuous rotation

• Pan/Tilt Resolution: 8/16 bit

• Feedback: Automatic repositioning after accidental movement

• Body: Aluminium structure with hi-resistance polycarbonate cover

• Body Color: Black

CONTROL

• Protocols: DMX512, RDM

• DMX Channels: 16/14/18ch

• RDM: RDM ready for xture remote monitor and settings

• Display: Black OLED high resolution display

• Firmware Upgrade: Yes, via USB-DMX interface (UPBOX1) not included

• Hibernation: Power Safe Mode when lost DMX

• Master/Slave: for synchronized operation of more units linked in a chain

ELECTRONICS

• Dimmer: Linear 0~100% electronic dimmer

• Strobe/Shutter: 1-25 Hz, electronic

• Operating Temperature: -10° ~ +45°

• Flicker: Flicker free operation

PIXIE BEAM

4

ELECTRICAL

• Power Supply: 100-240V – 50/60Hz

• Power Consumption (at 230V): 82W

• Power Consumption (at 120V): 82W

• Output (at 230V): 15 units on a single power line

PHYSICAL

• Cooling: Forced air with low noise fan

• Suspension And Fixing: Any position with “quick-lock” omega brackets

• Signal Connection: 5p in/out

• Power Connection: PowerCON in/out

• IP: 20

• Dimensions (WxHxD): 208x302x144mm

• Weight: 4kg

Photometric data

Illuminance at a Distance

4,5°

0m

2.5m

3.0m

5.0m

7.5m

0.35m

0.45m

0.75m

Lux Center Beam Angle: 4,5° Beam Width

11120lx

15850lx

4000lx

1.05m1803lx

Technical drawing

302mm

11,89in

144mm

5,67in

208mm

8,19in

Fig.1

5

PIXIE BEAM

1.3 OPERATING ELEMENTS AND CONNECTIONS

1

2

B

A

3

5 6 7

4

9 8

1. MOVING HEAD

2. ROTARY ARM

3. HANDLE

4. CONTROL PANEL with OLED

display and 4 button used to

access the control panel functions

and manage them.

5. MAIN FUSE HOLDER: replace a

burnt-out fuse by one of the same

type only.

6. POWER IN (PowerCON IN):

for connection to a socket

(100-240V~/50-60Hz) via the

supplied mains cable.

7. POWER OUT (PowerCON OUT):

power output for connection of

multiple units in series.

8. DMX OUT (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C

9. DMX IN (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C.

Fig.2

View A

View B

PIXIE BEAM

6

Fig.3

108

OMEGA

BRACKETS

- 2 - INSTALLATION

2.1 MOUNTING

The PIXIE BEAM may be set up on a solid and even surface. By means of the xing facilities of the baseplate,

the unit can also be mounted upside down to a cross arm. The base plate is shown in g.3. For xing, stable

mounting clips are required. According to the gure, the bolts of the brackets are placed into the openings

provided in the base plate and turned clockwise until they lock (to the stop). Always ensure that the unit

is rmly xed to avoid vibration and slipping while operating. The mounting place must be of sucient

stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any installa-

tion, always comply scrupulously with all the regulations (particularly regarding safety) currently in force

in the country in which the xture’s being used. Always additionally secure the projector with the safety

rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the maximum

fall of the projector will be 20 cm.

7

PIXIE BEAM

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). Switch on the PIXIE BEAM with the

power switch. The unit will run built-in program to reset all motors to their home position. Shortly after

that the PIXIE BEAM is ready for operation. After operation, switch o the unit with the power switch.

Disconnect the mains plug from the socket.

3.2 BASIC

The PIXIE BEAM has a OLED display and 4 button used to access the control panel functions and manage

them (g.4).

Fig.4 - Functions of the buttons

MODE UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

PIXIE BEAM

8

3.3 MENU STRUCTURE

MENU

1 Connect

ð

DMX Address

ð

Value (1-512) DMX address setting

Slave Rece

ð

Choose Slave mode

Sequence

ð

Alone/Master Choose Sequence mode

Music

ð

Alone/Master Choose Sound mode

2 Light

ð

Max Temperature

ð

Value 80~139° C/

176~282° F (85°C)

Lamp o if temperature

continuously over for 5

minutes

Lamp Adjust

ð

Pan, ... ,

ð

Value (000-255)

Adjust value of each

channels

3 Information

ð

Lamp Temp Temperature of driver

4 Set

ð

Reset

ð

All Reset

Movement

ð

Pan Reverse

ð

ON/OFF Pan Reverse

Tilt Reverse

ð

ON/OFF Tilt Reverse

Pan Degree

ð

540/630 Choose Pan Degree

Encoders

ð

ON/OFF Encoder wheel on/o

Move Mode

ð

Standard/Smooth Choose pan/tilt mode

Continuos

ð

Standard/Shortest

UI Set

ð

Mic Sens.

ð

Value (00-99%) Sensitivity of Mic

No Signal

ð

Close/Hold/Auto/Music Mode when no signal

Temperature C/F

ð

Fahrenheit /Celsius

Fans Mode

ð

Auto Speed/High Speed Fans mode

Hibernation

ð

OFF/Min (01-99) Sleeping mode

Backlight

ð

Always On/Min (02-99) Show backlight time

Flip Display

ð

ON/OFF Display 180°reverse

User Mode

ð

Standard/ Basic/

Extended

Users mode

Calibration

ð

Password

ð

050

Insert to unlock the

following settings

Pan

ð

Value (-128-127) Calibrate channel value

... ... ...

Fixture ID

Name

Rdm Mode

-Password-

PID Code

Software Ver. V1.2.00 IC Version

Reload Def

ð

Basic Reload

---Password---

All Reload

ON/OFF

9

PIXIE BEAM

3.4 SLAVE RECEIVE MODE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the rst unit in line; other units will work as slave with the same eect.

To set the drive as a slave, proceed as follows:

• Press the MODE button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, and select Slave Receive and press ENTER to

conrm.

• Press the MODE/ESC button repeatedly to exit the menu and save changes.

Use the DMX connectors of the PIXIE BEAM and an XLR cable to form a chain of units. Under certain

conditions and lengths you want to make a termination as shown on page 13.

3.5 OPERATIONS IN AUTOMATIC MODE

The unit independently runs through its show. Before you send an automatic program you need to set the

drive as Master/Alone:

• Press the MODE button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Sequence and press ENTER to conrm

your choice.

• Press the UP/DOWN button to select the mode of operation:

- Master, if the unit is connected in series with other units and it acts as the Master;

- Alone, if the unit is not connected to other units.

• Press the ENTER button to conrm your choice.

• Press the MODE/ESC button repeatedly to exit the menu and save changes.

The unit will go into automatic mode by executing the program automatically.

3.6 MUSIC MODE

In music mode, via its integrated microphone, the unit can be controlled by music with a clear rhythm in

the bass range. If the music control should not work optimally, increase the volume or reduce the distance

between the sound source and the light eect unit or alternatively increase the sensitivity of the micro-

phone.

• Press the MODE button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select Music and press ENTER to conrm.

• Press the UP/DOWN button to select the mode of operation:

- Master, if the mobile head is connected in series to other units, and it performs the Master function;

- Alone, if the xture is not connected to other units.

• Press the ENTER button to conrm your choice.

• Press the MODE/ESC button repeatedly to exit the menu and save changes.

The unit will go into music mode by executing an automatic program to the rhythm of music.

3.7 SENSITIVITY MICROPHONE

Select this function to set the value of the sensitivity of the microphone for use with a music control:

• Press the MODE button to access the main menu.

PIXIE BEAM

10

• Press the UP/DOWN button to scroll the menu, select the Set, then press the ENTER button to enter the

next menu.

• Press the UP/DOWN button to scroll through the menu, select UI Set, and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select Mic Sens. and press ENTER to conrm.

• Press the UP/DOWN button to adjust the level of sensitivity of the microphone, and then press the

ENTER button to conrm your choice.

• Press the MODE/ESC button repeatedly to exit the menu and save changes.

3.8 LINKING

Several units may be interconnected in order to control all further slave units to the same eect of the

master unit.

1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

3.9 DMX MODE

To enter the DMX mode, follow these steps:

• Press the MODE button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, select the DMX Address and press the ENTER key.

• Press the arrow keys to select the desired value (001-512). Press the ENTER key to conrm the setting.

• Press the MODE/ESC button repeatedly to exit the menu and save changes.

3.10 DMX CONFIGURATION

The PIXIE BEAM has 3 DMX channel congurations which can be accessed from the control panel.

• Press the MODE button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set, then press the ENTER button to enter the

next menu.

• Press the UP/DOWN button to scroll through the menu, select Users and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select User Mode and press ENTER to conrm

your choice.

• Use the UP/DOWN button to select the desired DMX channel conguration (Standard, Basic1, Extended),

then press the ENTER button to conrm your choice.

• Press the MODE/ESC button repeatedly to exit the menu and save changes.

The tables on page 13 show the mode of operation and their values DMX.

The unit is equipped with 5-pole XLR connections.

3.11 DMX ADDRESSING

For operation via light control unit with DMX512 protocol, is sucient connect the controller to PIXIE

BEAM. To able to operate the PIXIE BEAM with a light controller, adjust the DMX start address for the rst a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX

channel, adjust the start address 33 on the PIXIE BEAM. The other functions of the light eect panel are

then automatically assigned to the following addresses. An example with the start address 33 is shown

below:

11

PIXIE BEAM

DMX Address: 75DMX Address: 47DMX Address: 33 DMX Address: 61

Fig.5 - Example 14 DMX channels conguration

. . . . . . . . . . . .

DMX512 Controller

Numero

canali DMX

Indirizzo di

start (esempio)

Indirizzo DMX

occupati

Prossimo indirizzo di start

possibile per unità n°1

Prossimo indirizzo di start

possibile per unità n°2

Prossimo indirizzo di start

possibile per unità n°3

16 33 33-48 49 65 81

14 33 33-46 47 61 75

18 33 33-50 51 67 83

PIXIE BEAM

12

Fig.6

3.12 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.13 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Fig.7

Example:

5 pin XLR connector

13

PIXIE BEAM

3.14 DMX CONTROL

STD BA1 Ext

FUNCTION DMX

Value

16 Ch 14 Ch 18 Ch

1 1 1

PAN

0~100% 000 - 255

2 2

PAN FINE

0~100% 000 - 255

3 2 3

TILT

0~100% 000 - 255

4 4

TILT FINE

0~100% 000 - 255

5

PAN Continuous

No function

Forwards Pan rotation from fast to slow

No rotation

Backwards Pan rotation from slow to fast

000 - 003

004 - 127

128 - 131

132 - 255

6

TILT Continuous

No function

Forwards Pan rotation from fast to slow

No rotation

Backwards Pan rotation from slow to fast

000 - 003

004 - 127

128 - 131

132 - 255

5 3 7

MOVEMENT SPEED

Fast to slow 000 - 255

6 4

MOVEMENT FUNCTION

Normal

Movement with backout

PAN Forward Continuous Spin

PAN Reverse Continuous Spin

TILT Forward Continuous Spin

TILT Reverse Continuous Spin

PAN&TILT Forward Continuous Spin

PAN&TILT Reverse Continuous Spin

PAN Forward Spin & TILT Reverse Continuous Spin

PAN Reverse Spin & TILT Forward Continuous Spin

TBD

000 - 015

016 - 031

032 - 047

048 - 063

064 - 079

080 - 095

096 - 111

112 - 127

128 - 143

144 - 159

160 - 255

7 5 8

SHUTTER

Shutter closed

No function (shutter open)

Strobe eect slow to fast

No function (shutter open)

Pulse-eect in sequences

No function (shutter open)

Random strobe eect slow to fast

No function (shutter open)

000 - 031

032 - 063

064 - 095

096 - 127

128 - 159

160 - 191

192 - 223

224 - 255

8 6 9

DIMMER

Close to Open 0~100% 000 - 255

10

DIMMER Fade

0~100% 000 - 255

PIXIE BEAM

14

STD BA1 Ext

FUNCTION DMX

Value

16 Ch 14 Ch 18 Ch

9 7 11

VIRTUAL COLOR FUNCTION

On Function

CTC Function

Forward Spin

Reverse Spin

Continuous

Color Bounce

TBD

000 - 015

016 - 031

032 - 047

048 - 063

064 - 079

080 - 111

112 - 255

10 8 12

VIRTUAL COLOR1

CTC Function

Colour Temperature Correction 2000K->2700K

White 3200K

White 4200K

White 5600K

White 8000K

Forward Spin

Rainbow Eect (Slow->Fast)

Reverse Spin

Rainbow Eect (Slow->Fast)

Continuous & Color Bounce

Black

Red

Green

Blue

White

Red=0, Green->up, Blue=full, White=0

Red=0, Green=full,Blue->down,White=0

Red->up, Green=full,Blue=0,White=0

Red=full, Green->down,Blue=0,White=0

Red=full, Green=0,Blue->up,White=0

Red->down, Green=0,Blue=full,White=0

000 - 223

224 - 231

232 - 239

240 - 247

248 - 255

000 - 255

000 - 000

001 - 001

002 - 002

003 - 003

004 - 004

005 - 046

047 - 088

089 - 130

131 - 172

173 - 214

215 - 255

11 9 13

VIRTUAL COLOR2 (Only on Color Bounce)

Color Bounce

Black

Red

Green

Blue

White

Red=0, Green->up, Blue=full, White=0

Red=0, Green=full,Blue->down,White=0

Red->up, Green=full,Blue=0,White=0

Red=full, Green->down,Blue=0,White=0

Red=full, Green=0,Blue->up,White=0

Red->down, Green=0,Blue=full,White=0

000 - 000

001 - 001

002 - 002

003 - 003

004 - 004

005 - 046

047 - 088

089 - 130

131 - 172

173 - 214

215 - 255

15

PIXIE BEAM

STD BA1 Ext

FUNCTION DMX

Value

16 Ch 14 Ch 18 Ch

12 10 14

RED

0~100% 000 - 255

13 11 15

GREEN

0~100% 000 - 255

14 12 16

BLUE

0~100% 000 - 255

15 13 17

WHITE

0~100% 000 - 255

16 14 18

CONTROL

Normal

Reset All

Pan&Tilt Reset

TBD

Display O

Display On

TBD

Hibernation

TBD

000 - 007

008 - 015

016 - 023

024 - 055

056 - 063

064 - 071

072 - 079

080 - 087

088 - 095

096 - 255

PIXIE BEAM

16

3.15 FIXTURE SETTINGS

You can change the parameters for the device by following these steps:

• Press the MODE button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set, then press the ENTER button to enter the

next menu.

• Press the UP/DOWN button to scroll through the menu, then select Movement and press the ENTER but-

ton to enter the next menu.

• Use the UP/DOWN button to select the option proposed and press the ENTER button to conrm the

setting.

- Pan Reverse - Pan rotation in the opposite direction. Select OFF to deactivate the function (normal

setting); ON to activate the function (Pan Reverse).

- Tilt Reverse - Used for reversing tilt movement. Select OFF to deactivate the function (normal setting);

ON to activate the function (Tilt Reverse).

- Pan Degree - Angle of Pan. Select 540° or 630° to set the maximum angle of rotation of the moving

head.

- Encoders - Reorganization Pan/Tilt position after rolling away. Select OFF to deactivate or ON to ac-

tivate the function.

- Move Mode - Type of movement of the moving head. Select Standard to obtain a fast and uid move-

ment of Pan/Tilt, Smooth for a slower and softer movement of Pan/Tilt.

• Press the ENTER button to conrm your choice.

• Press the MODE/ESC button repeatedly to exit the menu and save changes.

3.16 LAMP SETTINGS

You can change the parameters of the device lamp by following these steps:

• Press the MODE button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Lights, then press the ENTER button to enter

the next menu.

• Press UP/DOWN to scroll through the menu, select one of the following settings and press the ENTER

button to display it.

- Max Temperature - Temperature operating limits. This function allows you to set the maximum tem-

perature inside the projector, after which the lamp will automatically turn o. Press the arrow but-

tons to set the desired temperature (80° -139°). Temperatures of less than 90°C are not critical. We

recommend that you enable this feature for temperatures higher than 90°.

- Lamp Adjust - Adjusts the lamp. This function allows you to modify all the parameters of the lamp: Pan,

... , etc. Press the UP/DOWN button to select one of the parameters and press ENTER to edit the value

(000-255) through the UP/DOWN button.

• Press the ENTER button to conrm your choice.

• Press the MODE/ESC button repeatedly to exit the menu and save changes.

3.17 DISPLAY SETTINGS

You can change the following parameters related to the display, following the same procedure:

• Press the MODE button to access the main menu.

• Press the UP/DOWN keys to scroll the menu, select the Setup, then press the ENTER button to enter the

next menu.

• Press UP/DOWN to scroll through the menu, then select UI Set, and press the ENTER button to enter the

next menu.

• Press UP/DOWN to scroll through the menu, and then select one of the following settings for the dis-

play and press the ENTER key to display it.

17

PIXIE BEAM

- Back Light - Backlight display Auto O. This feature allows you to automatically turn o the backlight

after a specied time that you can set using the arrow buttons. To have the display always on select

- Flip Display - Orientation of the display. This function allows you to rotate the display 180° to get a

better view of the display when the unit is hanging upside down. Select ON to activate or OFF to

disable this function.

• Press the ENTER button to conrm your choice.

• Press the MODE/ESC button repeatedly to exit the menu and save changes.

3.18 FIXTURE INFORMATION

To view all the information on the device, proceed as follows:

• Press the MODE button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Information, then press the ENTER button to

enter the next menu.

- Lamp Temperature - Through the Temperature function can be displayed the temperature inside the

xture, near the lamp. The temperature can be displayed in degrees Celsius or Fahrenheit.

• Press the MODE/ESC button repeatedly to exit the menu.

3.19 RESET FUNCTIONS

You can start a preset program to restore the selected function:

• Press the MODE button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set, then press the ENTER button to enter the

next menu.

• Press the UP/DOWN button to scroll through the menu, select Reset and press the ENTER button to

enter the next menu.

• Press the ENTER button to conrm your choice and wait for the recovery of the selected function.

3.20 SPECIAL FUNCTIONS

For the PIXIE BEAM you can access the following special functions:

No Signal

Select this feature to set the preferred mode of operation to be activated in case the drive is not present

no DMX signal input:

• Press the MODE button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set, then press the ENTER button to enter the

next menu.

• Press the UP/DOWN button to scroll through the menu, select UI Set, and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select No Signal and press ENTER to conrm.

• Press the UP/DOWN button to select the preferred mode of operation: Close/Hold/Auto/Music.

• Press the ENTER button to conrm your choice.

• Press the MODE/ESC button repeatedly to exit the menu and save changes.

Fans Mode

Select this function to set the fans operation mode:

• Press the MODE button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set, then press the ENTER button to enter the

next menu.

PIXIE BEAM

18

• Press the UP/DOWN button to scroll through the menu, select UI Set, and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, and then select Fans Mode and press ENTER to

conrm.

• Press the UP/DOWN button to select Auto Speed /High Speed , press the ENTER button to conrm your

choice.

• Press the MODE/ESC button repeatedly to exit the menu and save changes.

Hibernation

Select this function to activate the standby mode. This function will be activated automatically after a

period of inactivity, which is dened by the user. In standby mode, the lamp and all engines will not be

fed if no signal is sent. The unit will automatically reset and will return to operation as soon as the DMX

signal is sent.

• Press the MODE button to access the main menu.

• Press the UP/DOWN button to scroll through the menu, select the Set, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select UI Set, and press the ENTER button to

enter the next menu.

• Press the UP/DOWN to scroll through the menu, select Hibernation and press ENTER to conrm.

• Select the desired time through the arrow keys or select Not Hibernation to disable this function, then

press the ENTER button to conrm your choice.

• Press the MODE/ESC button repeatedly to exit the menu and save changes.

Calibration

Select this function to calibrate and adjust the wheels of the eects in their correct positions:

• Press the MODE button to access the main menu.

• Press the UP/DOWN button keys to scroll the menu, select the Set, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, then select Calibration and press the ENTER but-

ton to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select Password and press ENTER to conrm.

• Use the arrow keys to enter the password 050 and press ENTER to conrm.

• Once you have entered your password, you can set the values for Pan, ..., etc. Press the UP/DOWN button

to scroll through the menu, select one of the functions mentioned above and press ENTER to conrm

your choice.

• Use the arrow buttons to enter the desired value, then press the ENTER button to conrm your choice.

• Press the MODE/ESC button repeatedly to exit the menu and save changes.

Reload Default

Select this function to reset the unit to factory settings:

• Press the MODE button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set, then press the ENTER button to enter the

next menu.

• Press the UP/DOWN button to scroll through the menu, select Reload Default and press the ENTER button

to enter the next menu.

• Press the UP/DOWN button to select ON or OFF, then press the ENTER button to conrm.

Software Version

• Through Software Version function you can display the currently installed software version.

La pagina sta caricando ...

ProLights PIXIEBEAM Manuale utente

ProLights PIXIEBEAM Manuale utente

in altre lingue

Documenti correlati

Altri documenti