Raw International PF2 Manuale utente

Marca: Raw International

Modello: PF2

Categoria: Supporti da parete per schermi piatti

Tipo: Manuale utente

nal

rawinternational

rawin

nal

rawinternational

rawin

nal

rawinternational

rawin

nal

rawinternational

rawin

winternational

rawinternational

rawin

ational

rawinternational

rawin

winternational

rawinternational

rawin

ational

rawinternational

rawin

rawinternational

rawin

ational

rawinternational

rawin

rawinternational

rawin

rnational

rawin

nal

rawinternational

rawinte

nal

rawinternational

rawinternationa

nal

rawinternational

rawinte

nal

rawinternational

rawinternationa

nal

rawinternational

rawin

nal

rawinternational

rawinte

nal

rawinternational

rawinternationa

nal

rawintern

nal

rawinternational

nal

4. Security

Once the screen is safely suspended, please tighten the bolts on the bottom right and left corner of the

bracket using a screwdriver (DO NOT OVER TIGHTEN). This engages the front plates to the wall mounting

plate to ensure the screen cannot be lifted from the wall (ﬁg. 6).

PF2

INSTRUCTION

MANUAL

rawinternational

CONSULT AUTHORISED SERVICE PERSONNEL FOR

THE INSTALLATION OF THIS UNIT. INSTRUCTIONS

MUST BE FOLLOWED PRECISELY FOR SAFE AND

STABLE INSTALLATION. RAW INTERNATIONAL ARE

NOT LIABLE FOR ANY DAMAGE OR INJURY CAUSED

BY MISHANDLING OR IMPROPER INSTALLATION.

INSTALLATION (PLEASE READ CAREFULLY)

INSTALLATION OF THIS UNIT SHOULD ONLY BE CARRIED OUT BY QUALIFIED

TECHNICIANS. INSTALL IN AN APPROPRIATE LOCATION ONLY AFTER CHECKING

WALL STRUCTURE AND DURABILITY FOR ACCIDENT PREVENTION. CONSULT A

QUALIFIED BUILDER IF IN ANY DOUBT AS TO STRUCTURAL INTEGRITY OF WALL.

List of components Spacers

M4x20mm x 4 M5x20mm x 4 M6x20m x 4 M8x20mm x 4 17x8.3x5 x 4

M4X600mm x 4 M5x55mm x 4 M6x55 x 4 M8x55mm x 4 17x8.3x10 x 4

3mm hex key x 1 M5x75mm 4 5mm hex key x 1 M8x75mm x 4 17x8.3x20 x 4

4mm hex key x 1 6mm hex key x 1 17x8.3x30 x 4

17x8.3x40 x 4

bracket

screw driver

Fig. 4 Fig. 5

screen

Fig. 6

nal

rawinternational

rawin

nal

rawinternational

rawin

nal

rawinternational

rawin

nal

rawinternational

rawin

winternational

rawinternational

rawin

ational

rawinternational

rawin

winternational

rawinternational

rawin

ational

rawinternational

rawin

rawinternational

rawin

ational

rawinternational

rawin

rawinternational

rawin

rnational

rawin

nal

rawinternational

rawinte

nal

rawinternational

rawinternationa

nal

rawinternational

rawinte

nal

rawinternational

rawinternationa

nal

rawinternational

rawin

nal

rawinternational

rawinte

nal

rawinternational

rawinternationa

nal

rawintern

nal

rawinternational

nal

1. Mounting wall plate

Remove security screw from bottom of bracket

and detach front plate (ﬁg. 2). Mount wall plate

(ﬁg. 1) on wall in desired position using screws/

bolts suitable to construction of the wall. (If in any

doubt please consult a qualiﬁed builder). Attach

screws/bolts through as many holes/slots as

possible. There are a total of 22 ﬁxing holes on

the back plate, however the minimum amount of

ﬁxings that Raw International recommend is six.

(If in any doubt as to strength of ﬁxings please

consult a qualiﬁed builder.)

It is important that the front plates are ﬁxed as

centrally as possible to screen. To help achieve this,

there is a 2mm hole in the centre of each of the

front plates. Line this hole up so it is equal distance

between the top and bottom ﬁxings on the back of

the screen (ﬁg. 2). Once it is lined up, the nearest

ﬁxing hole on the front plates to the top ﬁxing

on the plasma screen are the ones that should

be ﬁxed ﬁrst (ﬁg. 3) using appropriate screws/

washers/isolators/spacers. Then ﬁx the bottom two

ﬁxings through the slots using appropriate screws/

washers/isolators/spacers. Please use an Allen key

to tighten all four ﬁxings. Only use isolators if back

of screen is not ﬂush with the front plates.

Ensure front plates are situated in a centralised

horizontal position, tighten the screws on the top of

the front plates (ﬁg. 5 overleaf) using a screw driver.

3. Engaging Plasma with the wall

Lift the display (minimum 2 people) with front

plates attached so that the bars engage with the

angled slots on the wall mounting plate (ﬁg. 5

overleaf), the screen is now safely suspended.

2. Attaching front plates to the

plasma screen

Place the screen face down on soft cloth (to

prevent damage) on a ﬂat surface. The ﬁxings you

use is dependent on the make and model of your

screen. There are different sets of ﬁxings supplied

with the bracket. Only ONE set of ﬁxings will be

required. In order to ascertain which set of ﬁxings

will be required, screw ﬁxings in the back of the

screen before attempting to attach front plates.

Only ONE set of ﬁxings will be of the correct

diameter for your screen.

Fig. 1

Mounting holes/slots

Fig. 3

security

screw

2mm

hole

screen

equal distance to 2mm hole

ﬁxings holes on back of screen

steel washer

nylon isolator

front plates

screen

steel ﬁxings

Fig. 3

Raw International PF2 Manuale utente

Marca: Raw International

Modello: PF2

Categoria: Supporti da parete per schermi piatti

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Raw International PF2 User manual

Raw International PF2 Manuale utente

Raw International PF2 Manuale utente

in altre lingue

Documenti correlati

Altri documenti