Raw International FL1 Manuale utente

Marca: Raw International

Modello: FL1

Categoria: Supporti da parete per schermi piatti

Tipo: Manuale utente

nal

rawinternational

rawin

nal

rawinternational

rawin

nal

rawinternational

rawin

nal

rawinternational

rawin

winternational

rawinternational

rawin

ational

rawinternational

rawin

winternational

rawinternational

rawin

ational

rawinternational

rawin

rawinternational

rawin

ational

rawinternational

rawin

rawinternational

rawin

rnational

rawin

nal

rawinternational

rawinte

nal

rawinternational

rawinternationa

nal

rawinternational

rawinte

nal

rawinternational

rawinternationa

nal

rawinternational

rawin

nal

rawinternational

rawinte

nal

rawinternational

rawinternationa

nal

rawintern

nal

rawinternational

nal

4. Security

Once the screen is safely suspended, please tighten the bolts on the bottom left and right of the bracket

using a screw driver (DO NOT OVER TIGHTEN) This engages the front plates to the wall mounting plates

to ensure the screen cannot be lifted from the wall (ﬁg. 6).

FL1

INSTRUCTION

MANUAL

rawinternational

CONSULT AUTHORISED SERVICE PERSONNEL FOR

THE INSTALLATION OF THIS UNIT. INSTRUCTIONS

MUST BE FOLLOWED PRECISELY FOR SAFE AND

STABLE INSTALLATION. RAW INTERNATIONAL ARE

NOT LIABLE FOR ANY DAMAGE OR INJURY CAUSED

BY MISHANDLING OR IMPROPER INSTALLATION.

INSTALLATION (PLEASE READ CAREFULLY)

INSTALLATION OF THIS UNIT SHOULD ONLY BE CARRIED OUT BY QUALIFIED

TECHNICIANS. INSTALL IN AN APPROPRIATE LOCATION ONLY AFTER CHECKING

WALL STRUCTURE AND DURABILITY FOR ACCIDENT PREVENTION. CONSULT A

QUALIFIED BUILDER IF IN ANY DOUBT AS TO STRUCTURAL INTEGRITY OF WALL.

List of components Spacers Penny Washer

M4x20mm x 4 M5x20mm x 4 M6x20m x 4 15x7.3x5 x 4 16x5.3x1.0 x 4

M4X45mm x 4 M5x45mm x 4 5mm hex key x 1 15x7.3x10 x 4

M4X55mm x 4 M5x55mm 4 M8x20mm x 4 15x7.3x30 x 4 Standard Washer

3mm hex key x 1 4mm hex key x 1 6mm hex key x 1 15x7.3x40 x 4 16x8.3x1.0 x 4

bracket

screw driver

Fig. 4 Fig. 5

screen

Fig. 6

nal

rawinternational

rawin

nal

rawinternational

rawin

nal

rawinternational

rawin

nal

rawinternational

rawin

winternational

rawinternational

rawin

ational

rawinternational

rawin

winternational

rawinternational

rawin

ational

rawinternational

rawin

rawinternational

rawin

ational

rawinternational

rawin

rawinternational

rawin

rnational

rawin

nal

rawinternational

rawinte

nal

rawinternational

rawinternationa

nal

rawinternational

rawinte

nal

rawinternational

rawinternationa

nal

rawinternational

rawin

nal

rawinternational

rawinte

nal

rawinternational

rawinternationa

nal

rawintern

nal

rawinternational

nal

1. Mounting wall plate

Remove security screw from bottom of bracket

and detach front plate (ﬁg. 2b). Mount wall plate

(ﬁg. 1) on wall in desired position using screws/

bolts suitable to construction of the wall. (If in any

doubt please consult a qualiﬁed builder). Attach

screws/bolts through as many ﬁxing as possible.

There are a total of 22 ﬁxing holes on the back

plate, however the minimum amount of ﬁxings

that Raw International recommend is six. (If in any

doubt as to strength of ﬁxings please consult a

qualiﬁed builder.)

It is important that the front plates are ﬁxed

as centrally as possible to the screen. To help

achieve this, there is a 2mm hole off centre of

each of the front plates. Line this hole up so it

is equal distance between the top and bottom

ﬁxings on the screen (ﬁg. 2). Once it is lined up,

the nearest ﬁxing hole on the front plates to the

top ﬁxing on the screen are the ones that should

be ﬁxed ﬁrst (ﬁg. 3) using appropriate screws/

washers/isolators/spacers. Please use an allen

key to tighten all four screws. Only use isolators if

back of screen is not ﬂush with the front plates.

Ensure front plates are situated in a centralised

position, tighten the screws on the bottom of the

front plates (ﬁg. 4 overleaf) using a screw driver.

3. Engaging the screen with the wall

Lift the screen (minimum two) people with front

plates attached so that the bars engage with the

angled slots on the wall mounting plates (ﬁg. 5

overleaf). The screen is now safely suspended.

steel washer

nylon isolator

front plates

screen

steel ﬁxings

Fig. 3

2. Attaching front plates to the

plasma screen

Place the screen face down on soft cloth (to

prevent damage) on a ﬂat surface (ﬁg. 2). The

ﬁxings you use are dependent on the make and

model of your screen. There are different sets of

ﬁxings supplied with the bracket. Only ONE set of

ﬁxings will be required. In order to ascertain which

set of ﬁxings will be required, screw ﬁxings in the

back of the screen before attempting to attach

front plates. Only ONE set of ﬁxings will be of the

correct diameter for your screen.

Fig. 1

Mounting holes/slots

Fig. 2

security

screw

2mm

hole

screen

equal distance to 2mm hole

ﬁxings holes on back of screen

Raw International FL1 Manuale utente

Marca: Raw International

Modello: FL1

Categoria: Supporti da parete per schermi piatti

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Raw International FL1 User manual

Raw International FL1 Manuale utente

Raw International FL1 Manuale utente

in altre lingue

Documenti correlati

Altri documenti