Sapphire Audio PI-AM3RS760G2 Quick Installation Manual

Quick Installation Guide



Sapphire Pure Innovation 760G

PI-AM3RS760G2

AMD 760G/ Socket AM3 Series Mainboard

TRADEMARK

Allproductsandcompanynamesaretrademarksorregisteredtrademarksoftheir

respectiveholders.

Thesespecificationsaresubjecttochangewithoutnotice.



ManualRevision1.0

October,2010

ii

Federal Communications Commission (FCC) Statement

This device has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with instructions contained in this manual, may cause harmful interference to

radio and television communications. However, there is no guarantee that interference will

not occur in a particular installation.

If this product does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

y Reorient or relocate the receiving antenna.

y Increase the separation between the equipment and receiver.

y Connect the product into an outlet on a circuit different from that to which the receiver

is connected.

y Consult the dealer or an experienced radio/TV technician for help.

Í

Note1: Connecting this device to peripheral devices that do not comply with Class B requirements, or

using an unshielded peripheral data cable, could also result in harmful interference to radio or

television reception

Note2: The user is cautioned that any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this product.

Note3: To ensure that the use of this product does not contribute to interference, it is necessary to use

shielded I/O cables

CE: Radiation of EN 55022 & Immunity of EN 55024

Waste Electrical and Electronic Equipment (WEEE) Statement

To protect the global environment, this product must be sent to separate collection

facilities for recovery and recycling.

DISPOSAL

Do not dispose of this product as unsorted municipal waste. Collect such waste

separately for special treatment.

iii

Environmental Safety Considerations

z Avoid locations where it is dusty, humid or may suffer from extreme temperatures. Do

not place the product in any area where it may become wet.

z The suitable ambient operating temperature is between 0 to 40 degrees centigrade.

z Dramatic changes in temperature may lead to malfunction due to constant thermal

expansion and contraction from the solder spots that connect components to the PCB.

When moving computers from a cold environment to a warmer one, please do not try to

turn the computer on until it has had a chance to warm up naturally. This reduces the

chance of condensation inside the computer, which could lead to water droplets

forming on the PCB or the surface of the components leading to phenomena as minor

as computer instability resulting from corrosion and oxidation or as major as a short

circuit that can burn out the components.

z Excessive temperature of the capacitors may decrease the life of computer. Ensure

adequate ventilation in your system case otherwise heat buildup may decrease the life

of the Mainboard or other devices.

z When over-clocking, please pay particular attention to the heat sink temperature.

Higher temperatures may decrease the life of the device and burn out the capacitors.

ii

Chapter 1 Introduction ....................................................................................... 1

1-1 Specification ................................................................................................................ 1

1-2 Mainboard Layout ....................................................................................................... 2

Chapter 2 Installation ......................................................................................... 3

2-1 Before You Begin ........................................................................................................ 3

2-2 Installing the I/O Shield ............................................................................................... 3

2-3 Securing to the Chassis .............................................................................................. 3

2-4 Installing CPU and FAN sink ...................................................................................... 3

2-5 Installing System Memory ........................................................................................... 4

2-6 Installing Expansion cards .......................................................................................... 5

2-7 Connectors .................................................................................................................. 6

2-8 Headers ...................................................................................................................... 8

2-9 Jumper Setting .......................................................................................................... 11

Chapter 3 Configuring the BIOS ...................................................................... 12

3-1 Enter BIOS Setup ..................................................................................................... 12

3-2 Main Menu ................................................................................................................ 13

3-3 Standard CMOS Features ........................................................................................ 14

3-4 Advanced BIOS Features ......................................................................................... 15

3-5 Advanced Chipset Features ..................................................................................... 16

3-6 Internal Graphics Configuration ................................................................................ 17

3-7 Power Management Features .................................................................................. 18

3-8 Miscellaneous Controls ............................................................................................. 19

3-9 PC Health Status ...................................................................................................... 20

3-10 Thermal Throttling Function .................................................................................... 21

3-11 Power User Overclock Settings .............................................................................. 21

3-12 Password Setting .................................................................................................... 22

3-13 Load Defaults .......................................................................................................... 23

3-14 Changes and Exit .................................................................................................... 24

Chapter 4 Driver Installation ............................................................................ 25



TABLE OF CONTENTS

- 1 -

Chapter 1 Introduction

11Specification

Spec. Description

Design

z

Micro ATX form factor, Size:24.5cm*20.0cm

Chipset

z

AMD 760G North Bridge Chipset

z

AMD SB710 South Bridge Chipset

CPU Socket

z

Supports AMD Phenom™ II / Athlon™ II / Sempron™ 100 Series CPU’s in AM3

Socket

z

Supports HT 3.0

Integrated

Graphics

z

ATI Radeon HD 3000 (Microsoft DX 10 Support)

Memory

Sockets

z

240-pin DDRIII Module slot x 2

z

Support 2pcs DDRIII 800/DDRIII 1066/DDRIII 1333 modules expandable to 8GB

z

Dual channel supported

Expansion

Slots

z

1 x PCI-Express 2.0 x16 lane slot

z

2 x 32-bit PCI slots

Storage

z

One IDE controller supports PCI Bus Mastering, ATA PIO/DMA and ULTRA DMA

33/66/100/133 functions, delivering data transfer rates up to 133 MB/s for two IDE

devices

z

Six Serial ATA2 ports providing 300 MB/sec data transfer rates with RAID 0, 1, 10,

JBOD functions

Ethernet LAN

z

Integrated PCI-E 10/100 LAN chip

z

Supports Fast Ethernet LAN function providing 10Mb/100Mbs data transfer rate

6 CH-Audio

z

Realtek ALC662 HD Audio 6-channel Audio Codec integrated

z

Audio driver and utility included

BIOS

z

AMI 8MB DIP Flash ROM BIOS

Multi I/O

z

PS/2 keyboard and PS/2 mouse connectors

z

DVI Connector x1

z

VGA Connector x1

z

USB 2.0 port x4 and header x2

z

RJ-45 LAN Connector x1

z

Audio connector x1(Line-in, Line-out, MIC)

z

IDE connector x1/ SATA connector x 6

z

Serial Port header x1

z

CDIN header x1

z

Audio header x1

- 2 -

12MainboardLayout

Rear I/O and layout for Pure Innovation 760G (PI-AM3RS760G2)

USB Connector

e

PS/2 Keyboard

Line-OUT

MIC-IN

VGA Connector

Line-IN

RJ-45 LAN

DVI Connector

PS/2 Mouse

Realtek Megabit

LAN Chip

ATA 133 IDE

Conn. (IDE1)

CPU Socket

ATX Power Conn.

PCI Slots

PS2 KB

/MS Por

t

ATX 12V Power Connector

Realtek ALC662

Audio Decode

CDIN Header

PWRLED1 Header

USB Heade

r

s

Front Panel

Audio Header

KB/USB Power On (JP1)

CPU FAN

SYSFAN2

DVI

Connector

COM1 Header

USB

Connector

AMD SB710 Chipset

VGA

Connector

DDRIII Slot x 2

8 MBit DIP Flash ROM BIOS

Audio

Connecto

r

RJ-45 over

USB Connecto

r

Speak Heade

r

Front Panel Header

Serial-ATAII Connecto

r

s

SATA1, 2, 3,4,5,6

SYSFAN1

AMD 760G Chipset

JBAT

PCI Express

X 16 by 16-lane

- 3 -

Chapter 2 Installation

21BeforeYouBegin

Turn off the power to your system and discharge your body’s static electric charge by

touching a grounded surface—for example, the metal surface of the power

supply—before performing any hardware procedure.

22InstallingtheI/OShield

Install the I/O shield before installing the mainboard in the chassis. Place the shield

inside the chassis. Press the shield into place so that it fits tightly and securely.

23SecuringtotheChassis

When installing the mainboard, you have to secure the mainboard into the chassis by

fastening with nine screws. Please refer to your chassis manual for instructions on

installing.

24InstallingCPUandFANsink

The mainboard provides a socket AM3 surface mount, Zero Insertion Force (ZIF)

socket, referred to as the mPGA940 socket supporting AMD AM3 processors.

The CPU should have a cooling FAN attached to prevent overheating. If this is not the

case, then purchase and install an appropriate cooling FAN before you turn on your

system.

To install the CPU, first turn off your system and remove its cover. Locate the ZIF

socket and open it by first pulling the level sideways away from the socket then

upward to a 90-degree angle. Insert the CPU with the correct orientation as shown

below. The notched corner should point toward the end of the lever. Because the CPU

has a corner pin for two of the four corners, the CPU will only fit in the orientation as

shown.

CPU ZIF mPGAB Socket

Colden Arrow

Socket AM3

No force is required to insert the CPU into the ZIF socket. Move the lever slightly to

get the correct alignment if it does not drop into the socket without force.

- 4 -

25InstallingSystemMemory

This mainboard has two 240-pin DIMM slots for DDR3 memory. These slots support

1GB, 2GB and 4GB DDR3 DIMMs.

Make sure that you install memory modules of the same type and density in the

correct DIMM sockets for Dual-Channel mode.

There must be at least one memory bank populated to ensure normal operation and

always insert the memory module into DIMM slot 1 first.

Memory Configuration:

Bank 240-Pin DIMM PCS Total Memory

Bank 0, 1 (DDRIII 1) DDRIII 800/DDRIII 1066/DDRIII 1333 X1 4GB

Bank 2, 3 (DDRIII 2) DDRIII 800/DDRIII 1066/DDRIII 1333 X1 4GB

Total Memory (Max.4GB) 2 8GB

DIMM 2 (BANK2+BANK3)

DIMM 1 (BANK0+BANK1)

Dual Channel

Supported



Memory Installation:

DDR3 and DDR2 memory modules are physically different. Please only install DDR3

DIMMs in this mainboard.

To install the DIMM, follow these steps:

1. Pull both clips on either side of the slot outwards. Align the DIMM module with the

slot ensuring that the notch in the DIMM lines up with the protrusion in the slot.

2. Press straight down until the plastic clips close and the module fits tightly into the

DIMM slot.

- 5 -

26InstallingExpansioncards

The mainboard provides one PCI Express x16 slot and two PCI slots.

PCI-E Slots

To install a PCI Express card:

1. Place the card in an available PCI Express slot and press down on the card until it is

completely seated in the slot. If the card is not seated properly, it could cause a

short across the pins.

2. Secure the card’s metal bracket to the chassis back panel with a screw.

PCI Slot

The PCI slots provided support a variety of expansion cards such as a LAN card, USB

card, SCSI card and other cards that comply with PCI specifications. When installing a

card into a PCI slot, be sure that it is fully seated. Secure the card’s metal bracket to

the chassis back panel with a screw.

32-bit PCI Slots

PCI-E x16 Slot by 16-lane

- 6 -

27Connectors

(1) Power Connector (24-pin block): ATXPWR1

ATXPWR1 is the main power supply

connector. Make sure that the

power supply cable and pins are

properly aligned with the connector

on the mainboard. Firmly plug the

power supply cable into the

connector and make sure it is

secure.

Í

Note: If you’d like to use the 20-pin ATX

power supply, please plug your

power supply aligning with pin 1 &

pin 13. The 24-pin main power

connector is backwardly compatible with ATX power supplies with 20-pin connectors.

.

20-pin power plug 24-pin power plug

(2) ATX 12V Power Connector (4-pin block): ATX12V

ATX12V, the 4-pin ATX 12V power connector, is used to provide power to the CPU.

Align the power plug to the connector and press firmly until seated.

ATX12V

+12V

Pin1

3

2

4

GND

Pin 1

ROW1 ROW2

24-Pin

ROW1 ROW2

Pin 1

20-Pin

PIN ROW1 ROW2

1 3.3V 3.3V

2 3.3V -12V

3 GND GND

4 5V Soft Power On

5 GND GND

6 5V GND

7 GND GND

8 Power OK -5V

9 +5V (for Soft Logic) +5V

10 +12V +5V

11 +12V +5V

12 +3V GND

- 7 -

(3) PS/2 Mouse & PS/2 Keyboard Connector: KB

These connectors are for a PS/2 keyboard and PS/2 Mouse.

(4) USB Port connector: CN5/ UL1 for USB

These are 4-pin connectors that connect USB devices to the system.

(5) LAN Port connector: UL1 for RJ-45 LAN

A standard RJ45 connector for network access supporting 10M/100 Mbps data

transfer rate.

(6) Audio Line-In, Line-Out, MIC Connector: CN3

3 Phone-Jack for LINE-IN, LINE-OUT and MIC audio connections.

Line-in: (BLUE) Audio input to sound chip

Line-out: (GREEN) Audio output to speaker

MIC: (PINK) Microphone Connector

(7) Primary IDE Connector (40-pin block): IDE1

The IDE connector supports Ultra ATA 133/100 IDE hard/optical disk drives. After

connecting the single plug end to mainboard, connect the two plugs at other end

to your hard disk(s). If you install two hard disks, you must configure the second

drive to Slave mode by setting its jumpers accordingly. Please refer to the

documentation of your hard / optical disk for the jumper settings.

IDE1 Connector

Pin 1

IDE

USB Connector

PS/2 Ke

y

board

Line-OUT

MIC-IN

VGA Connector

Line-IN

RJ-45 LAN

DVI Connector

PS/2 Mouse

- 8 -

(8) Serial-ATAII Port connector: SATA1,SATA 2,SATA3, SATA4, SATA5, SATA6

These allow connection of Serial ATA2 hard / optical disks to the mainboard using

the Serial ATA2 IDE cables provided.

(9) D-Sub 15-pin Connector: VGA

15-pin D_Sub VGA connector for attaching display devices such as CRT and LCD

monitors.

(10) Digital Visual Interface: DVI

A pure Digital interface standard designed to maximize the visual quality of digital

display devices such as flat panel LCD computer displays and digital projectors.

28Headers

(1) Line-Out/MIC Header for Front Panel (9-pin): AUDIO1

These headers connect to the Front Panel Line-out and MIC connectors.

Line-Out, MIC Headers

AUDIO

Pin 1

Lineout2-L

Lineout2-R

Sense-FB

Audio-GND

LINE2-JD

Audio-JD

2

9

10

KE

Y

MIC2-L

MIC2-JD

MIC2-R

- 9 -

(2) USB Port Headers (9-pin): USB1/USB2

These headers are used for connecting the additional USB ports. By attaching an

optional USB port cable, you can provide two additional USB ports on the back

panel.

USB Port Headers

Pin 1

VCC

-DATA

GND

+DATA

VCC

OC

-DATA

GND

+DATA

(3) Speaker connector: SPEAK1

This 4-pin connector connects to the case-mounted speaker. See the figure below.

(4) Power LED: PWR LED/PWRLED1

The Power LED will be illuminated when the system power is on. Connect the

Power LED from the system case to this pin.

(5) IDE Activity LED: HD LED

This connector connects to the hard disk activity indicator light on the case.

(6) Reset switch lead: RESET

This 2-pin connector connects to the case-mounted reset switch for resetting your

computer without having to turn off the power switch. This is a preferred

method of rebooting in order to prolong the life of the system’s power supply.

See the figure below.

(7) Power switch: PWR BTN

This 2-pin connector connects to the case-mounted power switch to power

ON/OFF the system.

System Case Connections

HDLED

RESET

VCC5

GND

VCC5

PWR LED

PWRBTN

PWRLED

HDDLE

RSTSW

NC

GND

JW FP

Pin 1

SPEAK1

SPKR

GND

NC

VCC5

Pin 1

PWRLED1

Pin 1

- 10 -

(8) FAN Headers: SYSFAN1 (3-pin), SYSFAN2 (3-pin), CPUFAN (4-pin)

These connectors support cooling fans up to 350mA (4.2 Watts). Depending on

the fan manufacturer, the wire and plug may be different. The red wire should be

positive, while the black should be ground. Connect the fan’s plug to the board

taking into consideration the polarity of connector.

FAN Power Headers

SYSFAN1

SYSFAN2

CPUFAN

1

4

GND

+12V

FAN1IN

FAN1 OUT

1

3

13

(9) CD Audio-In Headers (4-pin): CDIN1

CDIN is the connector for CD-Audio Input signal. Please connect it to the CD-ROM

CD-Audio output connector.

(10) Serial COM Port header: COM1

COM1 is the 9-pin Serial Port header.

Serial COM Port 9-pin Block

Pin1

CD Audio-In Headers

CDIN

4 1

- 11 -

29JumperSetting

(1) Keyboard/USB function Enabled/Disabled: JP1

Keyboard/Mouse & USB Power On Setting

2-3 Closed KB/USB Power ON Enabled

JP1

1-2 Closed KB/USB Power ON Disable (Default)

(2) CMOS RAM Clear (3-pin): JBAT

A battery must be used to retain the mainboard configuration in CMOS RAM.

Connecting pins 1 and 2 of JBAT is the normal position, storing the CMOS data.

To clear the CMOS, follow the procedure below:

1.

Turn off the system and unplug the AC power

2.

Remove ATX power cable from ATX power connector on the mainboard

3.

Locate JBAT and short pins 2-3 for a few seconds (move the jumper from 1-2

to 2-3)

4.

Return JBAT to its normal setting on 1-2

5.

Reconnect the ATX power cable back to ATX power connector on the

mainboard.

Note: When should you clear the CMOS?

1.

Troubleshooting

2.

If you forgot the system password

3.

If the system fails to boot after over clocking (to recover the default clock

settings)

CMOS RAM Clear Setting

2-3 Closed Clear CMOS

JBATJBAT

1-2 Closed Normal

- 12 -

Chapter 3 Configuring the BIOS

This chapter provides information on the BIOS Setup program and allows you to

configure the system for optimum use.

31EnterBIOSSetup

The BIOS is the communication bridge between hardware and software. Correctly

setting the BIOS parameters is critical to maintain optimal system performance.

Use the following procedure to change BIOS settings.

1. Power on the computer.

2. Press the Del key when the following message briefly shows upon the bottom of

the display during Power On Self Test (POST).

Press F1 to continue, DEL to enter Setup.

Pressing Del takes you to the BIOS CMOS Setup Utility.

Í

Note1: It is strongly recommended that you do not change the default BIOS settings. Changing

some settings could damage your computer.

Í

Note2: The BIOS options in this manual are for reference only. BIOS screens in manuals are usually

the first BIOS version when the board is released and may be different from your purchased

motherboard. Users are welcome to download the latest BIOS version from our official

website

Control Keys

Please check the following table for the function description of each Control key.

ControlKey(s) FunctionDescription

Å/Æ MovescursorleftorrighttoselectScreens

Ç/È Movescursorupordowntoselectitems

+/‐ Tochangeoptionfortheselecteditems

<Enter> Tobringuptheselectedscreen

<F1> TodisplaytheGeneralHelpScreen

<F6> ToLoadFail‐Safedefaultvaluesforall thesettings

<F7> Toloadoptimaldefaultvaluesforallthesettings

<F0> TosavechangesandexittheBIOSSETUPUTILITY

<ESC> TojumptotheExitScreenorexitthecurrentscreen

- 13 -

32MainMenu

When entering the BIOS SETUP UTILITY, the main menu screen appears. The Main

Menu allows you to select from 14 setup functions and 2 exit choices. Use arrow keys

to select among the items and press <Enter> to accept or enter the sub-menu.

Standard BIOS Features

Use this Menu for basic system configurations.

Advanced BIOS Features

Use this menu to set the Advanced Features available on your system.

Advanced Chipset Features

Use this menu to change the values in the chipset registers and optimize your

system’s performance.

Integrated Peripherals

Use this menu to specify your settings for integrated peripherals.

Power Management Features

Use this menu to specify your settings for power management.

Miscellaneous Control

Use this menu to specify your settings for miscellaneous control.

PC Health Status

This field shows your PC health status.

Thermal Throttling Function

Use this menu to specify your settings for thermal throttling Function

Power User Overclock Settings

Use this menu to specify your settings (frequency, Voltage) for overclocking demand.

Password Settings

Use this menu to specify your settings for Supervisor password and User password.

`ThermalThrottlingFunction

`PowerUserOverClocksettings

`PasswordSettings

LoadOptimalDefaults

LoadFailsafeDefaults

SaveChangesandExit

 DiscardChan

g

esand Exit

 :MoveEnter:Select+/‐/:ValueF10:SaveESC:ExitF1:GeneralHelp

F5:PreviousValuesF6:Fail‐SafeDefaultF7:OptimizedDefaults

`StandardCMOSFeatures

`AdvancedBIOSFeatures

`AdvancedChipsetFeatures

`IntegratedPeripherals

`PowerManagementSetup

`MiscellaneousControl

`PCHealthStatus

- 14 -

Load Optimal Defaults

Use this menu to load the BIOS default values these are setting for optimal

performances system operations for performance use.

Load Failsafe Defaults

This menu uses a minimal performance setting, but the system would run in a stable

way.

Save Changes and Exit

Save CMOS value changes to CMOS and exit setup.

Discard Changes and Exit

Abandon all CMOS value changes and exit setup.

33StandardCMOSFeatures



System Date

Allows you to set the system date. The format is <Day><Month><Date><Year>.

[Day] Weekday from Sun. to Sat., this is automatically displayed by BIOS.

[Month] The month from 1 to 12.

[Date] The date from 1 to 31 can be keyed by numeric function keys.

[Year] The year can be adjusted by users.

System Time

Allows you to set the system time. The time format is <hour>:<minute>:<second>.

Primary IDE Master / Slave

Sets the IDE configuration for the device that you specify.

SATA Channel 5/6/1/3/2/4

Use these functions to detect and configure the SATA channels.

System Memory

This item will show information about the memory modules(s) installed.

StandardBIOSFeatures

HelpItem

Whileentering

setup,BIOSauto

detectthepresence

ofIDEdevices.This

displaysthestatusof

autodetectionofIDE

devices.

 :MoveEnter:Select+/‐/:ValueF10:SaveESC:ExitF1:GeneralHelp

F5:PreviousValuesF6:Fail‐SafeDefaultF7:OptimizedDefaults

SystemDate Mon11/01/2010

SystemTime 1:15:10



`PrimaryIDEMaster NotDetected

`PrimaryIDESlave NotDetected

`SATAChannel5 NotDetected

`SATAChannel6 ATAPICDROM

`SATAChannel1 HardDisk

`SATAChannel3 NotDetected

`SATAChannel2 NotDetected

`SATAChannel4 NotDetected



SystemMemroy

Size

 :3328Mb

CMOSSetupUtility

–

- 15 -

34AdvancedBIOSFeatures

Use this menu to set the Advanced Features available on your system.

CPU Configuration

Allows you adjust the CPU related settings.

Quick Boot

Allows BIOS to skip certain tests while booting. This will decrease the needed to boot

the system.

1st Boot Device / 2nd Boot Device

Allows you to set the first/ second boot device where BIOS attempts to load the disk

operating system.

Boot Up NumLock Status

The default value is On.

On (default) Keypad is numeric keys.

Off Keypad is arrow keys.

ACPI APIC Support

Include ACPI APIC table pointer to RSDT pointer list.

MPS Revision

This option is only valid for multiprocessor motherboards as it specifies the version of

the Multiprocessor Specification (MPS) that the motherboard will use.

Quiet Boot

The optional settings are Enabled and Disable.

Disabled: Display normal POST message.

Enabled: Displays OME logo instead of POST message.

AdvancedBIOSFeatures

HelpItem

 :MoveEnter:Select+/‐/:ValueF10:SaveESC:ExitF1:GeneralHelp

F5:PreviousValuesF6:Fail‐SafeDefaultF7:OptimizedDefaults

AdvancedSettings

WARNIG:Settingwrongvaluesinbelowsectionsmaycause

systemtowalfunction.



`CPUConfiguration PressEnter

`HardDiskDrives PressEnter

`CD/DVDDrives PressEnter

QuickBoot Enabled

1stBootDevice SATA:3M‐WDCWD3200A

2ndBootDevice CD/DVD:SS‐PHILIPSS

BootupNum‐Lock ON

ACPIAPICsupport Enabled

MPSRevision 1.4

QuietBoot Disabled

F11BootMenu Enabled

CMOSSetupUtility

–

- 16 -

35AdvancedChipsetFeatures

The Advanced Chipset Features Setup option is used to change the values of the

chipset registers. These registers control most of the system options in the computer.

Memory Configuration

Press <Enter> to enter the sub-menu and specify your settings for Memory

Configuration adjust.

Internal Graphics Configuration

Press <Enter> to enter the sub-menu and specify your settings for Internal Graphics

Configuration.

PCI Express Configuration

Press <Enter> to enter the sub-menu and specify your settings for PCI Express

Configuration.

HDMI Audio

Use this item to select HDMI audio, the optional settings are: Disabled and Enabled.

NB Power Management Features

Dynamic clock gating for IOC/NT/MCU/CFG. Default is Enabled.

Primary Video Controller

This item is for user to choose primary video controller.

AdvancedChi

p

set Features

HelpItem

 :MoveEnter:Select+/‐/:ValueF10:SaveESC:ExitF1:GeneralHelp

F5:PreviousValuesF6:Fail‐SafeDefaultF7:OptimizedDefaults



`MemoryConfiguration PressEnter

`InternalGraphicsConfiguration PressEnter

`PCIExpressConfiguration PressEnter

HDMIAudio Disabled

NBPowerManagementFeatures Auto

PrimaryVideoController GFX0‐GPP‐IGFX‐PCI



CMOSSetupUtility

–

La pagina sta caricando ...

Sapphire Audio PI-AM3RS760G2 Quick Installation Manual

Questo manuale è adatto anche per

Sapphire Audio PI-AM3RS760G2 Quick Installation Manual

in altre lingue

Altri documenti