Emerio CBC-124348.1 Infrared Panel Heater Manuale utente

Marca: Emerio

Modello: CBC-124348.1 Infrared Panel Heater

Categoria: Illuminazione di comodità

Tipo: Manuale utente

- 1 -

Content – Inhalt – Teneur – Contenuto

Instruction manual – English ...................................................................................... - 2 -

Bedienungsanleitung – Deutsch ............................................................................... - 16 -

Mode d‘emploi – Français ........................................................................................ - 30 -

Manuale d'istruzioni – Italiano ................................................................................. - 44 -

- 2 -

Instruction manual – English

SAFETY INSTRUCTIONS

Before use make sure to read all of the below instructions in

order to avoid injury or damage, and to get the best results

from the appliance. Make sure to keep this manual in a safe

place. If you give or transfer this appliance to someone else

make sure to also include this manual.

In case of damage caused by user failing to follow the

instructions in this manual the warranty will be void. The

manufacturer/importer accepts no liability for damages

caused by failure to follow the manual, a negligent use or

use not in accordance with the requirements of this manual.

1. Read and save these instructions. Attention: pictures in

the IM are for reference only.

2. This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction

concerning use of the appliance in a safe way and

understand the hazards involved.

3. Children shall not play with the appliance.

4. Cleaning and user maintenance shall not be made by

children without supervision.

5. Children of less than 3 years should be kept away unless

continuously supervised.

6. Children aged from 3 years and less than 8 years shall only

switch on/off the appliance provided that it has been

placed or installed in its intended normal operating

position and they have been given supervision or

instruction concerning use of the appliance in a safe way

and understand the hazards involved. Children aged from

3 years and less than 8 years shall not plug in, regulate

and clean the appliance or perform user maintenance.

- 3 -

7. CAUTION — Some parts of this product can become very

hot and cause burns. Particular attention has to be given

where children and vulnerable people are present.

8. If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

9. This appliance is intended to be used in household and

similar applications.

10. Do not use outdoors. Do not use to dry clothes or any

fabric.

11. The heater must not be located immediately below a

socket outlet.

12. Do not use the heater if the power cord is damaged.

13. WARNING: In order to avoid overheating, do not cover

the heater.

14. WARNING: The heater must not be used if the panel is

damaged.

15. The heater is to be installed so that switches and other

controls cannot be touched by a person in the bath or

shower.

16. Do not use this heater in the immediate surroundings of a

bath, a shower or a swimming pool.

17. Means “DO NOT COVER“.

18. Keep combustible material such as furniture, cushions,

bedding, paper, clothes, curtains etc. at least 100cm away

from the heater.

19. This heater has hot and arcing or sparking parts inside. Do

not use it in the areas where gasoline, paint, or flammable

liquids are used or stored.

20. Always unplug the appliance when not in use.

21. The appliance is hot when in use. To avoid burned, do not

let bare skin touch hot surfaces.

- 4 -

22. The supply voltage and utility frequency, specified on the

machine, need to match those of the socket that is used.

Only use an undamaged, earthed socket that is secured

with a 30 mA earth leakage circuit breaker. The electrical

socket that you are using must be to hand at all times in

order to be able to remove the plug from the socket in the

event of an emergency.

23. Fully extend the cord before plugging in the heater. Make

sure it does not come into contact with any part of the

heater and prevent it from heating up any other way. Do

not run the cord underneath carpeting; do not cover it

with mats, carpet strips or similar and make sure it is not

placed in any passageways. Make sure the cord cannot be

stepped on and that no furniture is placed on top of it. Do

not lead the cord around sharp corners and do not roll it

up too tightly after use!

24. If possible, do not use an extension cord, as this causes

the risk of overheating and fire. If the use of an extension

cord is unavoidable, then make sure it is an undamaged,

approved extension cord with a minimum diameter of 2 x

1.5 mm² and a minimum permissible power of 1000 Watt.

To prevent overheating, always fully extend the cord!

25. Do not use the heater outdoors and do not use it in

spaces, smaller than 7 m³.

26. Make sure that the air around the heater can circulate

freely. Do not place the heater too close to walls or large

objects and do not place it under shelves, cupboards or

similar: take at all sides at least 30 cm free space and at

least 20 cm from the floor. For hanging installation: don’t

block the space between heater and wall.

27. Carefully supervise when this appliance is used in the

presence of children, incapacitated persons or pets. Let

persons who are not able to leave the room

independently, away from a working heater. The surface

becomes hot (up to 95°C), so keep children and people

with disabilities out of the neighborhood. Keep the

packaging material away from children.

- 5 -

28. Always switch the heater off, unplug it and leave to cool

down before:

- cleaning the heater

- carrying out maintenance on the heater

- touching or moving the heater.

29. Keep the heater clean. Dust, dirt and/or a buildup of

deposits in or behind the heater are a common cause of

overheating. Make sure these deposits are removed

regularly.

30. The appliance (incl. cord and plug) may only be opened

and/or repaired by properly authorized and qualified

persons.

31. Only use this heater for its intended purpose and as

described in this instruction manual.

32. Regarding the information pertaining to the installation,

please refer to the below paragraph of the manual.

- 6 -

CBC-124348.1 EN

PARTS DESCRIPTION

1. Heating panel

2. Temperature sensor

3. Power switch

4. Control panel

5. Remote control

a) LED display

b) On/off button

c) Time set button

d) Value increase button

e) Value decrease buttons

LED display

a) Temperature / Data

b) Heating symbol

c) Open-window detection symbol

d) Power indicator light

- 7 -

Remote control

1. On/off button

2. Cancel button

3. Open-window detection button

4. Set button

5. Ok button

6. Edit button

7. ECO button

8. Temperature button

9. Time on button

10. Time off button

11. Value increase button

12. Value decrease button

13. Week button

WALL MOUNTING

The fixing materials supplied are intended for a brick wall. If you are using a different type of surface, you

should supply appropriate fixing materials yourself.

This heater has been designed to hang securely from the wall. Do not use it until it has been properly

installed, as described in these instructions for use and never, for example, in a standing position or when

leaning against something!

Please take below minimum distance picture (fig.1) for reference.

(fig.1) (fig.2)

Please pay attention to fig.2: The wall-mounting system (A & B) on the rear side of the appliance should be

pre-mounted in order to hang it vertically. Viewed from the front, the power switch is at the bottom side and

the control panel is at the right-hand side.

A. Wall mounting bracket & knobs

B. Wall spacer (Bracket for keeping space from the appliance to the wall)

Note: The knobs and wall spacer have already been installed on the rear side by the factory.

- 8 -

Please install the wall mounting bracket by following steps.

1. Choose a firm, even, vertical wall made of heat-resistant material on which to hang the appliance.

2. Define the position of the wall mounting bracket: the bracket should be mounted horizontal to the wall.

Position the bracket in such a manner that the minimum distances stated in fig.1 are guaranteed after the

appliance is mounted to the wall. Mount the bracket with the correct side upwards (see the mark “This

side up” on the bracket).

3. Mark the positions of the four holes to be drilled on the wall.

4. Drill 10mm holes in the marked places.

5. Insert the bolts (A&B) into the holes with a hammer. Put on the wall bracket. Secure the wall bracket

immovably against the wall by using the washer (C), gasket (D) and nut (E).

6. Hang the panel by letting the knobs through the eyes in the wall mounting bracket. Slide the panel as far as

possible to the right side and lower it as far as possible. Now the panel is mounted securely.

7. To remove the panel from the wall, you must lift and slide in the opposite direction, until the knobs are in

front of the eyes again. Now you can take the panel off.

Note: Guide the electric cable immediately downwards and make sure that it does not come into contact with

the panel. Do not conceal the cable behind the heater!

 Holes

 Bolts

 Wall mounting bracket

- 9 -

OPERATION

Plug the appliance into an appropriate electrical outlet. Turn on the appliance by pressing the power switch to

position “I”. The power indicator light will be illuminated on the LED display. The appliance is standby.

You can use the control panel on the appliance or the separate remote control to operate your appliance.

Please note the control panel can only operate the basic functions. The remote control can operate the basic

functions as well as the advanced functions.

The remote control should be directed towards the LED display while using.

Basic functions:

1. Press the on/off button to turn on the appliance. Press the button again to turn the appliance off.

2. Set the temperature.

1) Press the button “+” or “-” to set your desired temperature. You can choose from 0-37℃. Long

pressing for rapid adjustment.

2) The LED display will flash the set temperature approx. 10 seconds and then turn back to show the

current temperature. It means the temperature has been set.

3) If the set temperature is higher than the current temperature, the appliance will start to heat and the

heating symbol will be illuminated on the LED display. If the set temperature is reached, the appliance

will automatically switch off and then switch on again when the room cools down. The heating symbol

will be off and illuminated again accordingly.

Note: If no button is pressed in approx. two minutes, the current temperature will disappear from the LED

display. Pressing any button will make the current temperature re-appear.

3. Set the current day and time (so that you can set the weekly timer function later.)

1) Let the appliance be on but not heat. Therefore, no heating symbol is illuminated on the LED display.

(Do this by setting the temperature lower than the current temperature, for example.)

2) Follow below steps in the table to set the current day and time. When using the control panel, please

press the button “M”. When using the remote control, please press the button “SET”.

Step

Press button

The LED display shows

Note

M / SET (3 sec.)

HH flashes

It means to set the day of today.

+ or –

01 to 07

01 = Monday, 02 = Tuesday, 03 = Wednesday, 04 =

Thursday, 05 = Friday, 06 = Saturday, 07 = Sunday.

M / SET

H1 flashes

It means to set the current hour.

+ or –

00 to 23

Choose the correct hour.

M / SET

H2 flashes

It means to set the current minute.

+ or –

00 to 59

Choose the correct minute.

M / SET

Current temperature

It means the day and time are set.

4. Check the current day and time.

1) Let the appliance be on and heat. Therefore, the heating symbol is illuminated on the LED display. (Do

this by setting the temperature higher than the current temperature, for example.)

2) Consecutively press the button “M” (on the control panel) / “SET” (on the remote control) to check the

current day and time:

HH: day of the week;

H1: hour;

H2: minute.

- 10 -

More advanced functions: (Only by remote control.)

Weekly timer function

1. Follow below steps in the table to set the weekly timer.

Step

Press button

The LED display shows

Note

WEEK (3 sec.)

UU flashes

SET

ON or OF flashes

+ or –

ON or OF flashes

Select:

+ = ON: Timer function will be on. (During the set times, the

heater will automatically switch on/off.)

– = OF: Timer function will be off (During the set times, the

heater will not automatically switch on/off.)

SET

01 or 99 flashes

+ or –

01 or 99 flashes

Select:

+ = 01: All timer settings will be executed only once.

– = 99: All timer settings will be executed repeatedly. [See

Attention (1)].

SET

U1 flashes

+ or –

U1 to U7 flashes

Select the day of the week (U1 = Monday, U2 = Tuesday, etc.)

for which you want to make a timer.

The selected day

01 flashes

+ or –

01 to 04 flashes

You can make totally 4 timers per day. So name the timer with

a number (01, 02, 03 or 04) to distinguish from each other.

[See Attention (2)].

The selected number

TEMP

+ or –

00 to 37 flashes

Set the desired temperature (0 - 37 °C). The default setting

is 20 °C.

The selected

temperature

TIME ON

+ or –

00 to 23 flashes

Set the desired start time from 00 to 23. [See Attention

(3)].

The selected start time

TIME OFF

+ or –

“start time +1” to 24

flashes

Set the desired stop time from the “start time +1” to 24.

For example, if the start time is 10, the stop time can only

be set from 11 to 24. [See Attention (3)].

The selected stop time

Timer setting is finished. The current temperature will appear on the LED display after approx. 10 seconds.

If you want to set the second timer, please repeat the steps above.

- 11 -

Attention (1):

The timer settings which you make under “01” (executed only once) should be made for the current week. On

Sunday (day 7) at 24:00, all “01” settings will be set to “non-activated”. Therefore, a timer setting for Saturday

that you made on Tuesday will work, but a timer setting for Tuesday that you make on Saturday will not work!

Attention (2):

If a timer setting with number 01 was made for this day, you must manually set the next timer setting for this

day to 02 using the button “+”. Otherwise the timer setting 01 will be overwritten.

Attention (3):

Start & stop times can only be set in whole hours (not in minutes).

Note:

 If the appliance is switched off by using the power switch or by removing the plug from the electrical

outlet, the day will be set to 01 and the time will count from 00 (hour) and 00 (minute) for the next time

you switch the appliance on again. However, the timers that were set previously are still stored. Therefore,

to avoid misunderstandings, the weekly timer function will be automatically set to OFF (“OF” shown in LED

display) in case of turning the heater off using the power switch or removing the plug from the socket.

Otherwise, the heater would switch on and off at the wrong times. Make sure to reset the current day and

time once turn on the appliance again and remember to set the weekly timer function to ON (“ON” shown

in the LED display) as described in above table.

 During the timer setting, if no button is pressed for approx. 10 seconds, the timer setting will stop and you

will have to start all over again.

 All timer settings – maximum 28 settings: seven (7) days multiplied by maximum four (4) settings per day –

are processed consecutively. Therefore, make sure that they do NOT contain contradictions.

2. Cancel the timer settings

1) Cancel all the timer settings.

Press the button “WEEK” for approx. 3 seconds until the LED display shows the flashing “UU”.

Long press the button “C” until a beep sound is heard. It means all the timer settings are cancelled.

2) Cancel all timer settings of a specific day.

Press the button “WEEK” for approx. 3 seconds until the LED display shows the flashing “UU”.

Press the button “SET” consecutively until the LED display shows the flashing “U1” (day 1, for

example).

Press the button “+” / “-” to select the day for which you want to cancel the timer settings.

Long press the button “C” until a beep sound is heard. It means all the timer settings of the day are

cancelled.

3) Cancel a specific timer setting.

Press the button “WEEK” for approx. 3 seconds until the LED display shows the flashing “UU”.

Press the button “SET” consecutively until the LED display shows the flashing “U1” (day 1, for

example).

Press the button “+” / “-” to select the day for which you want to cancel the timer setting.

Press the button “ED”.

Press the button “+” / “-” to select the number of the timer setting that you want to cancel.

Long press the button “C” until a beep sound is heard. It means this timer setting is cancelled.

- 12 -

3. Check the timer settings

Press the button “WEEK” consecutively. You will see the following settings in sequence:

- Timer on (ON) or timer off (OF)

- Once only (01) or repeatedly (99)

- U1-U7, day of the week

- Timer setting number of the day concerned (01, 02, 03 or 04)

- The set temperature

- Start time in hours

- Stop time in hours

All 28 timer settings are shown, also the timer settings that have not been filled. The temperature of the

non-filled timer settings is 20 °C.

Open-window detection function

Press the open-window detection button on the remote control. The open-window detection symbol will

appear on the LED display. If the ambient temperature decreases 8℃ or more within 15 minutes, the heater

will turn off and the related symbol will flash. If this is the case and you press the button again, the heater will

resume its normal operation.

ECO function

This appliance is equipped with the ECO function. If the button “ECO” is pressed, the LED display will show “EC”.

The appliance will start to heat if the ambient temperature drops to below 16℃ and will turn off if the

ambient temperature increases to above 16℃. Press the button “ECO” again to switch off the ECO function.

SAFETY FEATURE

In case of internal overheating, the overheating safeguard will switch the heater off. This may occur if the

heater cannot give off enough heat or if it cannot draw in enough fresh air. As mentioned above, this is

generally caused by (partially) covering the heater, or installing the heater too close to a wall or something

similar. In case of overheating, switch off the heater and unplug. Give the heater time to cool down, remove

the source of the overheating and use as normal. If the problem persists or if you have not been able to trace

the source of the overheating, turn the heater off immediately and unplug. Contact a servicing support to have

the heater repaired.

CLEANING AND MAINTENANCE

Keep the heater clean. Switch off the heater, remove the plug from the socket and allow the heater to cool

down before cleaning or carrying out maintenance work.

 Wipe the outside of the heater regularly with a dry or slightly damp cloth. Do not use aggressive soaps,

sprays, cleaners or abrasives, waxes, polishes or chemical solutions which can cause irreparable scratches

and damage! You can keep the back of the heater free of dust with a feather duster. For thorough cleaning

of the back, you can take the heater from the wall.

 If you want to store the heater at the end of the season, remove it from the wall, unscrew the wall

mounting bracket and store the entire unit (in the original packaging) upright in a cool, dry and frost-free

place.

TECHNICAL DATA:

Operating voltage: 230V ~ 50-60Hz

Power consumption: 300W

- 13 -

GUARANTEE AND CUSTOMER SERVICE

Before delivery, our devices are subjected to rigorous quality control. If, despite all care, damage has occurred

during production or transportation, please return the device to your dealer. In addition to statutory legal

rights, the purchaser has an option to claim under the terms of the following guarantee:

For the purchased device we provide 2 years guarantee, commencing from the day of sale. If you have a

defective product, you can directly go back to the point of purchase.

Defects which arise due to improper handling of the device and malfunctions due to interventions and repairs

by third parties or the fitting of non-original parts are not covered by this guarantee. Always keep your receipt,

without the receipt you cannot claim any form of warranty. Damage caused by not following the instruction

manual, will lead to a void of warranty, if this results in consequential damages then we will not be liable.

Neither can we hold responsible for material damage or personal injury caused by improper use if the

instruction manual is not properly executed. Damage to accessories does not mean free replacement of the

whole appliance. In such case, please contact our service department. Broken glass or breakage of plastic parts

is always subject to a charge. Defects to consumables or parts subjected to wearing, as well as cleaning,

maintenance, replacement of said parts or shipping and transportation costs to and from any place of repair

are not covered by the warranty and are to be paid.

ENVIRONMENT FRIENDLY DISPOSAL

Recycling – European Directive 2012/19/EU

This marking indicates that this product should not be disposed with other household wastes. To

prevent possible harm to the environment or human health from uncontrolled waste disposal,

recycle it responsibly to promote the sustainable reuse of material resources. To return your used

device, please use the return and collection systems or contact the retailer where the product was purchased.

They can take this product for environmentally safe recycling.

Emerio Switzerland AG

Oberneuhofstrasse 1

6340 Baar

Switzerland

BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY. DO NOT OPEN. DO NOT

DISPOSE OR IN FIRE OR SHORT CIRCUIT.

- 14 -

ERP information (EN)

Supplier: Emerio Switzerland AG

Oberneuhofstrasse 1

6340 Baar

Switzerland

Declare that the product detailed below:

Information requirements for electric local space heaters

Model identifier(s):

Item

Symbol

Value

Unit

Item

Unit

Heat output

Type of heat input, for electric storage

local space heaters only (select one)

Nominal heat

output

Pnom

0,3

manual heat charge control, with

integrated thermostat

Minimum heat

output (indicative)

Pmin

N/A

manual heat charge control with room

and/or outdoor temperature feedback

Maximum

continuous heat

output

Pmax,c

0,3

electronic heat charge control with room

and/or outdoor temperature feedback

Auxiliary

electricity

consumption

fan assisted heat output

At nominal heat

output

elmax

0,282

Type of heat output/room temperature control

(select one)

At minimum heat

output

elmin

N/A

single stage heat output and no room

temperature control

In standby mode

elSB

0,000228

Two or more manual stages, no room

temperature control

with mechanic thermostat room

temperature control

with electronic room temperature control

electronic room temperature control plus

day timer

electronic room temperature control plus

week timer

Yes

Other control options (multiple selections

possible)

room temperature control, with presence

detection

room temperature control, with open

window detection

Yes

with distance control option

with adaptive start control

- 15 -

with working time limitation

with black bulb sensor

Contact details

Emerio Switzerland AG

Oberneuhofstrasse 1

6340 Baar

Switzerland

Satisfies the requirement of the Council Directives:

COMMISSION REGULATION (EU) No 2015/1188 of 28 April 2015 and Amending COMMISSION REGULATION (EU)

2016/2282 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to

ecodesign requirements for local space heaters

Regarding information for consumers on how to install, use and maintain the product, WEEE information,

please check the instruction manual provided with packaging.

- 16 -

Bedienungsanleitung – Deutsch

SICHERHEITSHINWEISE

Lesen Sie vor dem Gebrauch unbedingt die nachfolgenden

Anleitungen, um Verletzungen oder Beschädigungen zu

vermeiden und das beste Ergebnis mit dem Gerät zu erzielen.

Bewahren Sie diese Bedienungsanleitung an einem sicheren

Ort auf. Wenn Sie dieses Gerät an eine andere Person

weitergeben, stellen Sie sicher, dass Sie auch diese

Bedienungsanleitung aushändigen.

Im Falle von Beschädigungen, die durch die Missachtung der

Anleitungen in dieser Bedienungsanleitung verursacht

wurden, wird die Garantie ungültig. Der Hersteller/Importeur

haftet nicht für Schäden, die durch Missachtung der

Bedienungsanleitung, fahrlässigen Gebrauch oder Benutzung,

die nicht in Übereinstimmung mit den Anforderungen dieser

Bedienungsanleitung erfolgt, verursacht wurden.

1. Lesen und bewahren Sie diese Anleitungen auf. Achtung:

Die Bilder in der Bedienungsanleitung dienen nur zur

Veranschaulichung.

2. Dieses Gerät kann von Kindern ab 8 Jahren sowie von

Personen mit reduzierten physischen, sensorischen oder

mentalen Fähigkeiten oder Mangel an Erfahrung und/oder

Wissen benutzt werden, wenn sie beaufsichtig oder

bezüglich des sicheren Gebrauchs des Gerätes

unterwiesen wurden und die daraus resultierenden

Gefahren verstanden haben.

3. Kinder dürfen nicht mit dem Gerät spielen.

4. Kinder sollten dieses Gerät nicht unbeaufsichtigt reinigen

oder warten.

5. Kinder unter 3 Jahre sollten ferngehalten werden, außer

sie werden ständig beaufsichtigt.

6. Kinder ab 3 Jahre und unter 8 Jahre dürfen das Gerät nur

an- und ausschalten, unter der Voraussetzung, dass es an

die normale Betriebsposition platziert oder montiert

wurde und sie beaufsichtigt werden oder in der sicheren

Bedienung des Gerätes unterrichtet wurden und die

- 17 -

involvierten Gefahren verstehen. Kinder ab 3 Jahre und

unter 8 Jahre dürfen das Gerät nicht an das Stromnetz

anschließen, einstellen und reinigen oder

Wartungsarbeiten durchführen.

7. VORSICHT — Einige Teile dieses Produktes werden sehr

heiß und können Verbrennungen verursachen. In

Anwesenheit von Kindern und schutzbedürftigen

Personen muss besonders aufgepasst werden.

8. Wenn die Netzanschlussleitung dieses Gerätes beschädigt

wird, muss sie durch den Hersteller oder seinen

Kundendienst oder eine ähnlich qualifizierte Person

ersetzt werden, um Gefährdungen zu vermeiden.

9. Dieses Gerät ist für den Gebrauch in Haushalten und

ähnlichen Anwendungsbereichen vorgesehen.

10. Nicht im Freien verwenden. Nicht zum Trocknen von

Kleidung oder anderer Stoffe verwenden.

11. Das Heizgerät darf nicht direkt unter einer Steckdose

platziert werden.

12. Das Heizgerät nicht verwenden, wenn das Anschlusskabel

beschädigt ist.

13. WARNUNG: Um eine Überhitzung des Heizgeräts zu

vermeiden, darf das Heizgerät nicht abgedeckt werden.

14. WARNUNG: Das Heizgerät darf nicht benutzt werden,

wenn die Platte beschädigt ist.

15. Das Heizgerät muss so installiert werden, dass seine

Schalter und anderen Bedienelemente nicht von einer

Person berührt werden können, die sich in der

Badewanne oder in der Dusche befindet.

16. Dieses Heizgerät nicht in unmittelbarer Nähe einer

Badewanne, einer Dusche order eines Schwimmbeckens

benutzen.

17. Bedeutet " Nicht abdecken ".

18. Halten Sie brennbares Material wie Möbel, Kissen,

Bettwäsche, Papier, Kleidung, Vorhänge usw. mindestens

100 cm vom Heizgerät entfernt.

- 18 -

19. Im Innern dieses Heizgeräts befinden sich Teile, die Hitze,

Lichtbögen oder Funken erzeugen können. Nicht in

Bereichen einsetzen, in denen Benzin, Lacke oder

entzündliche Flüssigkeiten verwendet oder gelagert

werden.

20. Bei Nichtgebrauch immer den Netzstecker ziehen.

21. Während des Gebrauch wird das Gerät heiß. Die

ungeschützte Haut vor heißen Flächen fernhalten, es

besteht Verbrennungsgefahr.

22. Die auf dem Gerät angegebene Versorgungsspannung und

Frequenz müssen mit den Werten der verwendeten

Steckdose übereinstimmen. Das Gerät darf nur an eine

geerdete Steckdose, die in einwandfreiem Zustand und

mit einem Fehlerspannungsschutzschalter mit 30 mA

versehen ist, angeschlossen werden. Die verwendete

Steckdose muss jederzeit gut zugänglich sein, damit der

Stecker in einem Notfall schnell aus der Steckdose

gezogen werden kann.

23. Kabel komplett abwickeln, bevor das Heizgerät mit der

Steckdose verbunden wird. Das Kabel darf mit keinem Teil

des Heizgerätes in Kontakt kommen und muss vor

anderen Hitzequellen geschützt werden, damit es sich

nicht erhitzt. Das Kabel darf nicht unter Teppichen verlegt

werden, nicht mit Matten, Läufern oder ähnlichen Dingen

bedeckt werden und nicht in Durchgängen platziert

werden. Es ist darauf zu achten, dass niemand auf das

Kabel treten kann und keine Möbelstücke auf das Kabel

gestellt werden. Das Kabel darf nicht um spitze Ecken

gelegt und nach dem Gebrauch zu fest aufgewickelt

werden.

24. Von der Verwendung eines Verlängerungskabels wird

abgeraten, da sich das Risiko der Überhitzung und eines

Feuers dadurch erhöht. Wenn die Verwendung eines

Verlängerungskabels sich nicht vermeiden lässt, sollte ein

unversehrtes, zugelassenes Verlängerungskabel mit einem

Durchmesser von 2 x 1,5 mm2, das für mindestens

1000 Watt Leistung geeignet ist, benutzt werden. Um

Überhitzung zu vermeiden, das Kabel immer vollständig

abwickeln!

- 19 -

25. Das Heizgerät nicht im Freien und nicht in Räumen unter

7 m³ verwenden.

26. Die Luft in der Umgebung des Heizgeräts muss

ungehindert zirkulieren können. Das Heizgerät darf nicht

zu nah an Wänden oder großen Gegenständen und unter

Regalen, Schränken oder dergleichen aufgestellt werden.

Es muss an allen Seiten ein Abstand von mindestens 30

cm und mindestens 20 cm zum Boden eingehalten

werden. Bei Wandmontage: Den Platz zwischen Heizgerät

und Wand nicht blockieren.

27. Eine sorgfältige Überwachung ist erforderlich, wenn das

Gerät in Anwesenheit von Kindern, behinderten Personen

oder Haustieren benutzt wird. Personen, die das Zimmer

nicht ohne Hilfe verlassen können, von dem Heizgerät

wegführen. Die Oberfläche wird sehr heiß (bis zu 95°C). Es

ist deshalb dafür zu sorgen, dass sich Kinder und Personen

mit Behinderungen nicht in der Nähe des Geräts aufhalten.

Verpackungsmaterial von Kindern fernhalten.

28. Heizgerät immer ausschalten, den Stecker aus der

Steckdose ziehen und abkühlen lassen, bevor:

- das Heizgerät gereinigt wird;

- Wartungsarbeiten am Heizgerät vorgenommen werden;

- das Heizgerät berührt oder umgestellt wird.

29. Das Heizgerät ist sauber zu halten. Staub, Schmutz

und/oder Ablagerungen in oder hinter dem Heizgerät sind

eine häufige Ursache von Überhitzung. Diese

Ablagerungen müssen regelmäßig entfernt werden.

30. Das Gerät (inklusive Kabel und Stecker) darf nur von einer

autorisierten Fachkraft geöffnet und/oder repariert

werden.

31. Dieses Heizgerät nur zu seinem Bestimmungszweck und

wie in dieser Bedienungsanleitung beschrieben benutzen.

32. Um Informationen über die Installation zu erhalten, lesen

Sie bitte den nachfolgenden Abschnitt in dieser

Bedienungsanleitung.

La pagina sta caricando ...

Emerio CBC-124348.1 Infrared Panel Heater Manuale utente

Marca: Emerio

Modello: CBC-124348.1 Infrared Panel Heater

Categoria: Illuminazione di comodità

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Emerio CBC-124348.1 Infrared Panel Heater User manual
français: Emerio CBC-124348.1 Infrared Panel Heater Manuel utilisateur
Deutsch: Emerio CBC-124348.1 Infrared Panel Heater Benutzerhandbuch

Emerio CBC-124348.1 Infrared Panel Heater Manuale utente

Emerio CBC-124348.1 Infrared Panel Heater Manuale utente

in altre lingue

Documenti correlati

Altri documenti