Emerio CBC-122043.1 Infrared Panel Heater Manuale utente

Categoria
Illuminazione di comodità
Tipo
Manuale utente
CBC-122043.1
Infrared panel heater (EN)
Infrarotheizung (DE)
Radiateur infrarouge (FR)
Pannello radiante a infrarossi (IT)
- 1 -
Content Inhalt Teneur Contenuto
Instruction manual English ...................................................................................... - 2 -
Bedienungsanleitung Deutsch ............................................................................... - 16 -
Mode d‘emploi – Français ........................................................................................ - 30 -
Manuale d'istruzioni Italiano ................................................................................. - 44 -
- 2 -
Instruction manual English
SAFETY INSTRUCTIONS
Before use make sure to read all of the below instructions in
order to avoid injury or damage, and to get the best results
from the appliance. Make sure to keep this manual in a safe
place. If you give or transfer this appliance to someone else
make sure to also include this manual.
In case of damage caused by user failing to follow the
instructions in this manual the warranty will be void. The
manufacturer/importer accepts no liability for damages
caused by failure to follow the manual, a negligent use or
use not in accordance with the requirements of this manual.
1. Read and save these instructions. Attention: pictures in
the IM are for reference only.
2. This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction
concerning use of the appliance in a safe way and
understand the hazards involved.
3. Children shall not play with the appliance.
4. Cleaning and user maintenance shall not be made by
children without supervision.
5. Children of less than 3 years should be kept away unless
continuously supervised.
6. Children aged from 3 years and less than 8 years shall only
switch on/off the appliance provided that it has been
placed or installed in its intended normal operating
position and they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children aged from
3 years and less than 8 years shall not plug in, regulate
and clean the appliance or perform user maintenance.
- 3 -
7. CAUTION Some parts of this product can become very
hot and cause burns. Particular attention has to be given
where children and vulnerable people are present.
8. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
9. This appliance is intended to be used in household and
similar applications.
10. Do not use outdoors. Do not use to dry clothes or any
fabric.
11. The heater must not be located immediately below a
socket outlet.
12. Do not use the heater if the power cord is damaged.
13. WARNING: In order to avoid overheating, do not cover
the heater.
14. WARNING: The heater must not be used if the panel is
damaged.
15. The heater is to be installed so that switches and other
controls cannot be touched by a person in the bath or
shower.
16. Do not use this heater in the immediate surroundings of a
bath, a shower or a swimming pool.
17. Means “DO NOT COVER“.
18. Keep combustible material such as furniture, cushions,
bedding, paper, clothes, curtains etc. at least 100cm away
from the heater.
19. This heater has hot and arcing or sparking parts inside. Do
not use it in the areas where gasoline, paint, or flammable
liquids are used or stored.
20. Always unplug the appliance when not in use.
21. The appliance is hot when in use. To avoid burned, do not
let bare skin touch hot surfaces.
- 4 -
22. The supply voltage and utility frequency, specified on the
machine, need to match those of the socket that is used.
Only use an undamaged, earthed socket that is secured
with a 30 mA earth leakage circuit breaker. The electrical
socket that you are using must be to hand at all times in
order to be able to remove the plug from the socket in the
event of an emergency.
23. Fully extend the cord before plugging in the heater. Make
sure it does not come into contact with any part of the
heater and prevent it from heating up any other way. Do
not run the cord underneath carpeting; do not cover it
with mats, carpet strips or similar and make sure it is not
placed in any passageways. Make sure the cord cannot be
stepped on and that no furniture is placed on top of it. Do
not lead the cord around sharp corners and do not roll it
up too tightly after use!
24. If possible, do not use an extension cord, as this causes
the risk of overheating and fire. If the use of an extension
cord is unavoidable, then make sure it is an undamaged,
approved extension cord with a minimum diameter of 2 x
1.5 mm² and a minimum permissible power of 1000 Watt.
To prevent overheating, always fully extend the cord!
25. Do not use the heater outdoors and do not use it in
spaces, smaller than 7 m³.
26. Make sure that the air around the heater can circulate
freely. Do not place the heater too close to walls or large
objects and do not place it under shelves, cupboards or
similar: take at all sides at least 30 cm free space and at
least 20 cm from the floor. For hanging installation: don’t
block the space between heater and wall.
27. Carefully supervise when this appliance is used in the
presence of children, incapacitated persons or pets. Let
persons who are not able to leave the room
independently, away from a working heater. The surface
becomes hot (up to 95°C), so keep children and people
with disabilities out of the neighborhood. Keep the
packaging material away from children.
- 5 -
28. Always switch the heater off, unplug it and leave to cool
down before:
- cleaning the heater
- carrying out maintenance on the heater
- touching or moving the heater.
29. Keep the heater clean. Dust, dirt and/or a buildup of
deposits in or behind the heater are a common cause of
overheating. Make sure these deposits are removed
regularly.
30. The appliance (incl. cord and plug) may only be opened
and/or repaired by properly authorized and qualified
persons.
31. Only use this heater for its intended purpose and as
described in this instruction manual.
32. Regarding the information pertaining to the installation,
please refer to the below paragraph of the manual.
- 6 -
CBC-122043.1 EN
PARTS DESCRIPTION
1. Heating panel
2. Temperature sensor
3. Power switch
4. Control panel
5. Remote control
a) LED display
b) On/off button
c) Time set button
d) Value increase button
e) Value decrease buttons
LED display
a) Temperature / Data
b) Heating symbol
c) Open-window detection symbol
d) Power indicator light
- 7 -
Remote control
1. On/off button
2. Cancel button
3. Open-window detection button
4. Set button
5. Ok button
6. Edit button
7. ECO button
8. Temperature button
9. Time on button
10. Time off button
11. Value increase button
12. Value decrease button
13. Week button
WALL MOUNTING
The fixing materials supplied are intended for a brick wall. If you are using a different type of surface, you
should supply appropriate fixing materials yourself.
This heater has been designed to hang securely from the wall. Do not use it until it has been properly
installed, as described in these instructions for use and never, for example, in a standing position or when
leaning against something!
Please take below minimum distance picture (fig.1) for reference.
(fig.1) (fig.2)
Please pay attention to fig.2: The wall-mounting system (A & B) on the rear side of the appliance should be
pre-mounted in order to hang it vertically. Viewed from the front, the power switch is at the bottom side and
the control panel is at the right-hand side.
A. Wall mounting bracket & knobs
B. Wall spacer (Bracket for keeping space from the appliance to the wall)
Note: The knobs and wall spacer have already been installed on the rear side by the factory.
A
B
- 8 -
Please install the wall mounting bracket by following steps.
1. Choose a firm, even, vertical wall made of heat-resistant material on which to hang the appliance.
2. Define the position of the wall mounting bracket: the bracket should be mounted horizontal to the wall.
Position the bracket in such a manner that the minimum distances stated in fig.1 are guaranteed after the
appliance is mounted to the wall. Mount the bracket with the correct side upwards (see the mark This
side up on the bracket).
3. Mark the positions of the four holes to be drilled on the wall.
4. Drill 10mm holes in the marked places.
5. Insert the bolts (A&B) into the holes with a hammer. Put on the wall bracket. Secure the wall bracket
immovably against the wall by using the washer (C), gasket (D) and nut (E).
6. Hang the panel by letting the knobs through the eyes in the wall mounting bracket. Slide the panel as far as
possible to the right side and lower it as far as possible. Now the panel is mounted securely.
7. To remove the panel from the wall, you must lift and slide in the opposite direction, until the knobs are in
front of the eyes again. Now you can take the panel off.
Note: Guide the electric cable immediately downwards and make sure that it does not come into contact with
the panel. Do not conceal the cable behind the heater!
Holes
Bolts
Wall mounting bracket
- 9 -
OPERATION
Plug the appliance into an appropriate electrical outlet. Turn on the appliance by pressing the power switch to
position “I”. The power indicator light will be illuminated on the LED display. The appliance is standby.
You can use the control panel on the appliance or the separate remote control to operate your appliance.
Please note the control panel can only operate the basic functions. The remote control can operate the basic
functions as well as the advanced functions.
The remote control should be directed towards the LED display while using.
Basic functions:
1. Press the on/off button to turn on the appliance. Press the button again to turn the appliance off.
2. Set the temperature.
1) Press the button “+ or “-” to set your desired temperature. You can choose from 0-37. Long
pressing for rapid adjustment.
2) The LED display will flash the set temperature approx. 10 seconds and then turn back to show the
current temperature. It means the temperature has been set.
3) If the set temperature is higher than the current temperature, the appliance will start to heat and the
heating symbol will be illuminated on the LED display. If the set temperature is reached, the appliance
will automatically switch off and then switch on again when the room cools down. The heating symbol
will be off and illuminated again accordingly.
Note: If no button is pressed in approx. two minutes, the current temperature will disappear from the LED
display. Pressing any button will make the current temperature re-appear.
3. Set the current day and time (so that you can set the weekly timer function later.)
1) Let the appliance be on but not heat. Therefore, no heating symbol is illuminated on the LED display.
(Do this by setting the temperature lower than the current temperature, for example.)
2) Follow below steps in the table to set the current day and time. When using the control panel, please
press the button “M”. When using the remote control, please press the button “SET”.
Step
Press button
Note
1
M / SET (3 sec.)
It means to set the day of today.
2
+ or
01 = Monday, 02 = Tuesday, 03 = Wednesday, 04 =
Thursday, 05 = Friday, 06 = Saturday, 07 = Sunday.
3
M / SET
It means to set the current hour.
4
+ or
Choose the correct hour.
5
M / SET
It means to set the current minute.
6
+ or
Choose the correct minute.
7
M / SET
It means the day and time are set.
4. Check the current day and time.
1) Let the appliance be on and heat. Therefore, the heating symbol is illuminated on the LED display. (Do
this by setting the temperature higher than the current temperature, for example.)
2) Consecutively press the button “M” (on the control panel) / “SET” (on the remote control) to check the
current day and time:
HH: day of the week;
H1: hour;
H2: minute.
- 10 -
More advanced functions: (Only by remote control.)
Weekly timer function
1. Follow below steps in the table to set the weekly timer.
Step
Press button
The LED display shows
Note
1
WEEK (3 sec.)
UU flashes
2
SET
ON or OF flashes
3
+ or
ON or OF flashes
Select:
+ = ON: Timer function will be on. (During the set times, the
heater will automatically switch on/off.)
= OF: Timer function will be off (During the set times, the
heater will not automatically switch on/off.)
4
OK
UU
5
SET
01 or 99 flashes
6
+ or
01 or 99 flashes
Select:
+ = 01: All timer settings will be executed only once.
= 99: All timer settings will be executed repeatedly. [See
Attention (1)].
7
OK
UU
8
SET
U1 flashes
9
+ or
U1 to U7 flashes
Select the day of the week (U1 = Monday, U2 = Tuesday, etc.)
for which you want to make a timer.
10
OK
The selected day
11
ED
01 flashes
12
+ or
01 to 04 flashes
You can make totally 4 timers per day. So name the timer with
a number (01, 02, 03 or 04) to distinguish from each other.
[See Attention (2)].
13
OK
The selected number
14
TEMP
HP
15
+ or
00 to 37 flashes
Set the desired temperature (0 - 37 °C). The default setting
is 20 °C.
16
OK
The selected
temperature
17
TIME ON
HE
18
+ or
00 to 23 flashes
Set the desired start time from 00 to 23. [See Attention
(3)].
19
OK
The selected start time
20
TIME OFF
HF
21
+ or
“start time +1” to 24
flashes
Set the desired stop time from the “start time +1” to 24.
For example, if the start time is 10, the stop time can only
be set from 11 to 24. [See Attention (3)].
22
OK
The selected stop time
Timer setting is finished. The current temperature will appear on the LED display after approx. 10 seconds.
If you want to set the second timer, please repeat the steps above.
- 11 -
Attention (1):
The timer settings which you make under “01” (executed only once) should be made for the current week. On
Sunday (day 7) at 24:00, all 01” settings will be set to “non-activated. Therefore, a timer setting for Saturday
that you made on Tuesday will work, but a timer setting for Tuesday that you make on Saturday will not work!
Attention (2):
If a timer setting with number 01 was made for this day, you must manually set the next timer setting for this
day to 02 using the button “+”. Otherwise the timer setting 01 will be overwritten.
Attention (3):
Start & stop times can only be set in whole hours (not in minutes).
Note:
If the appliance is switched off by using the power switch or by removing the plug from the electrical
outlet, the day will be set to 01 and the time will count from 00 (hour) and 00 (minute) for the next time
you switch the appliance on again. However, the timers that were set previously are still stored. Therefore,
to avoid misunderstandings, the weekly timer function will be automatically set to OFF (“OF” shown in LED
display) in case of turning the heater off using the power switch or removing the plug from the socket.
Otherwise, the heater would switch on and off at the wrong times. Make sure to reset the current day and
time once turn on the appliance again and remember to set the weekly timer function to ON (ON” shown
in the LED display) as described in above table.
During the timer setting, if no button is pressed for approx. 10 seconds, the timer setting will stop and you
will have to start all over again.
All timer settings maximum 28 settings: seven (7) days multiplied by maximum four (4) settings per day
are processed consecutively. Therefore, make sure that they do NOT contain contradictions.
2. Cancel the timer settings
1) Cancel all the timer settings.
Press the button “WEEK” for approx. 3 seconds until the LED display shows the flashing “UU”.
Long press the button “C” until a beep sound is heard. It means all the timer settings are cancelled.
2) Cancel all timer settings of a specific day.
Press the button “WEEK” for approx. 3 seconds until the LED display shows the flashing “UU”.
Press the button “SET consecutively until the LED display shows the flashing “U1” (day 1, for
example).
Press the button “+” / “-” to select the day for which you want to cancel the timer settings.
Long press the button “Cuntil a beep sound is heard. It means all the timer settings of the day are
cancelled.
3) Cancel a specific timer setting.
Press the button “WEEK” for approx. 3 seconds until the LED display shows the flashing “UU”.
Press the button “SET consecutively until the LED display shows the flashing “U1” (day 1, for
example).
Press the button “+” / “-” to select the day for which you want to cancel the timer setting.
Press the button “ED”.
Press the button “+” / “-” to select the number of the timer setting that you want to cancel.
Long press the button “C” until a beep sound is heard. It means this timer setting is cancelled.
- 12 -
3. Check the timer settings
Press the button “WEEK” consecutively. You will see the following settings in sequence:
- Timer on (ON) or timer off (OF)
- Once only (01) or repeatedly (99)
- U1-U7, day of the week
- Timer setting number of the day concerned (01, 02, 03 or 04)
- The set temperature
- Start time in hours
- Stop time in hours
All 28 timer settings are shown, also the timer settings that have not been filled. The temperature of the
non-filled timer settings is 20 °C.
Open-window detection function
Press the open-window detection button on the remote control. The open-window detection symbol will
appear on the LED display. If the ambient temperature decreases 8 or more within 15 minutes, the heater
will turn off and the related symbol will flash. If this is the case and you press the button again, the heater will
resume its normal operation.
ECO function
This appliance is equipped with the ECO function. If the button “ECO” is pressed, the LED display will show “EC.
The appliance will start to heat if the ambient temperature drops to below 16 and will turn off if the
ambient temperature increases to above 16. Press the button “ECO” again to switch off the ECO function.
SAFETY FEATURE
In case of internal overheating, the overheating safeguard will switch the heater off. This may occur if the
heater cannot give off enough heat or if it cannot draw in enough fresh air. As mentioned above, this is
generally caused by (partially) covering the heater, or installing the heater too close to a wall or something
similar. In case of overheating, switch off the heater and unplug. Give the heater time to cool down, remove
the source of the overheating and use as normal. If the problem persists or if you have not been able to trace
the source of the overheating, turn the heater off immediately and unplug. Contact a servicing support to have
the heater repaired.
CLEANING AND MAINTENANCE
Keep the heater clean. Switch off the heater, remove the plug from the socket and allow the heater to cool
down before cleaning or carrying out maintenance work.
Wipe the outside of the heater regularly with a dry or slightly damp cloth. Do not use aggressive soaps,
sprays, cleaners or abrasives, waxes, polishes or chemical solutions which can cause irreparable scratches
and damage! You can keep the back of the heater free of dust with a feather duster. For thorough cleaning
of the back, you can take the heater from the wall.
If you want to store the heater at the end of the season, remove it from the wall, unscrew the wall
mounting bracket and store the entire unit (in the original packaging) upright in a cool, dry and frost-free
place.
TECHNICAL DATA:
Operating voltage: 230V ~ 50-60Hz
Power consumption: 720W
- 13 -
GUARANTEE AND CUSTOMER SERVICE
Before delivery, our devices are subjected to rigorous quality control. If, despite all care, damage has occurred
during production or transportation, please return the device to your dealer. In addition to statutory legal
rights, the purchaser has an option to claim under the terms of the following guarantee:
For the purchased device we provide 2 years guarantee, commencing from the day of sale. If you have a
defective product, you can directly go back to the point of purchase.
Defects which arise due to improper handling of the device and malfunctions due to interventions and repairs
by third parties or the fitting of non-original parts are not covered by this guarantee. Always keep your receipt,
without the receipt you cannot claim any form of warranty. Damage caused by not following the instruction
manual, will lead to a void of warranty, if this results in consequential damages then we will not be liable.
Neither can we hold responsible for material damage or personal injury caused by improper use if the
instruction manual is not properly executed. Damage to accessories does not mean free replacement of the
whole appliance. In such case, please contact our service department. Broken glass or breakage of plastic parts
is always subject to a charge. Defects to consumables or parts subjected to wearing, as well as cleaning,
maintenance, replacement of said parts or shipping and transportation costs to and from any place of repair
are not covered by the warranty and are to be paid.
ENVIRONMENT FRIENDLY DISPOSAL
Recycling European Directive 2012/19/EU
This marking indicates that this product should not be disposed with other household wastes. To
prevent possible harm to the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material resources. To return your used
device, please use the return and collection systems or contact the retailer where the product was purchased.
They can take this product for environmentally safe recycling.
Emerio Switzerland AG
Oberneuhofstrasse 1
6340 Baar
Switzerland
BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY. DO NOT OPEN. DO NOT
DISPOSE OR IN FIRE OR SHORT CIRCUIT.
- 14 -
ERP information (EN)
Supplier: Emerio Switzerland AG
Oberneuhofstrasse 1
6340 Baar
Switzerland
Declare that the product detailed below:
Information requirements for electric local space heaters
Model identifier(s):
Item
Symbol
Value
Unit
Item
Unit
Heat output
Type of heat input, for electric storage
local space heaters only (select one)
Nominal heat
output
Pnom
0,7
kW
manual heat charge control, with
integrated thermostat
No
Minimum heat
output (indicative)
Pmin
N/A
kW
manual heat charge control with room
and/or outdoor temperature feedback
No
Maximum
continuous heat
output
Pmax,c
0,7
kW
electronic heat charge control with room
and/or outdoor temperature feedback
No
Auxiliary
electricity
consumption
fan assisted heat output
No
At nominal heat
output
elmax
0,703
kW
Type of heat output/room temperature control
(select one)
At minimum heat
output
elmin
N/A
kW
single stage heat output and no room
temperature control
No
In standby mode
elSB
0,000228
kW
Two or more manual stages, no room
temperature control
No
with mechanic thermostat room
temperature control
No
with electronic room temperature control
No
electronic room temperature control plus
day timer
No
electronic room temperature control plus
week timer
Yes
Other control options (multiple selections
possible)
room temperature control, with presence
detection
No
room temperature control, with open
window detection
Yes
with distance control option
No
with adaptive start control
No
- 15 -
with working time limitation
No
with black bulb sensor
No
Contact details
Emerio Switzerland AG
Oberneuhofstrasse 1
6340 Baar
Switzerland
Satisfies the requirement of the Council Directives:
COMMISSION REGULATION (EU) No 2015/1188 of 28 April 2015 and Amending COMMISSION REGULATION (EU)
2016/2282 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to
ecodesign requirements for local space heaters
Regarding information for consumers on how to install, use and maintain the product, WEEE information,
please check the instruction manual provided with packaging.
- 16 -
Bedienungsanleitung Deutsch
SICHERHEITSHINWEISE
Lesen Sie vor dem Gebrauch unbedingt die nachfolgenden
Anleitungen, um Verletzungen oder Beschädigungen zu
vermeiden und das beste Ergebnis mit dem Gerät zu erzielen.
Bewahren Sie diese Bedienungsanleitung an einem sicheren
Ort auf. Wenn Sie dieses Gerät an eine andere Person
weitergeben, stellen Sie sicher, dass Sie auch diese
Bedienungsanleitung aushändigen.
Im Falle von Beschädigungen, die durch die Missachtung der
Anleitungen in dieser Bedienungsanleitung verursacht
wurden, wird die Garantie ungültig. Der Hersteller/Importeur
haftet nicht r Schäden, die durch Missachtung der
Bedienungsanleitung, fahrlässigen Gebrauch oder Benutzung,
die nicht in Übereinstimmung mit den Anforderungen dieser
Bedienungsanleitung erfolgt, verursacht wurden.
1. Lesen und bewahren Sie diese Anleitungen auf. Achtung:
Die Bilder in der Bedienungsanleitung dienen nur zur
Veranschaulichung.
2. Dieses Gerät kann von Kindern ab 8 Jahren sowie von
Personen mit reduzierten physischen, sensorischen oder
mentalen Fähigkeiten oder Mangel an Erfahrung und/oder
Wissen benutzt werden, wenn sie beaufsichtig oder
bezüglich des sicheren Gebrauchs des Gerätes
unterwiesen wurden und die daraus resultierenden
Gefahren verstanden haben.
3. Kinder dürfen nicht mit dem Gerät spielen.
4. Kinder sollten dieses Gerät nicht unbeaufsichtigt reinigen
oder warten.
5. Kinder unter 3 Jahre sollten ferngehalten werden, außer
sie werden ständig beaufsichtigt.
6. Kinder ab 3 Jahre und unter 8 Jahre rfen das Gerät nur
an- und ausschalten, unter der Voraussetzung, dass es an
die normale Betriebsposition platziert oder montiert
wurde und sie beaufsichtigt werden oder in der sicheren
Bedienung des Gerätes unterrichtet wurden und die
- 17 -
involvierten Gefahren verstehen. Kinder ab 3 Jahre und
unter 8 Jahre rfen das Gerät nicht an das Stromnetz
anschließen, einstellen und reinigen oder
Wartungsarbeiten durchführen.
7. VORSICHT Einige Teile dieses Produktes werden sehr
heiß und können Verbrennungen verursachen. In
Anwesenheit von Kindern und schutzbedürftigen
Personen muss besonders aufgepasst werden.
8. Wenn die Netzanschlussleitung dieses Gerätes bescdigt
wird, muss sie durch den Hersteller oder seinen
Kundendienst oder eine ähnlich qualifizierte Person
ersetzt werden, um Gefährdungen zu vermeiden.
9. Dieses Gerät ist r den Gebrauch in Haushalten und
ähnlichen Anwendungsbereichen vorgesehen.
10. Nicht im Freien verwenden. Nicht zum Trocknen von
Kleidung oder anderer Stoffe verwenden.
11. Das Heizgerät darf nicht direkt unter einer Steckdose
platziert werden.
12. Das Heizgerät nicht verwenden, wenn das Anschlusskabel
beschädigt ist.
13. WARNUNG: Um eine Überhitzung des Heizgeräts zu
vermeiden, darf das Heizgerät nicht abgedeckt werden.
14. WARNUNG: Das Heizgerät darf nicht benutzt werden,
wenn die Platte beschädigt ist.
15. Das Heizgerät muss so installiert werden, dass seine
Schalter und anderen Bedienelemente nicht von einer
Person berührt werden können, die sich in der
Badewanne oder in der Dusche befindet.
16. Dieses Heizgerät nicht in unmittelbarer he einer
Badewanne, einer Dusche order eines Schwimmbeckens
benutzen.
17. Bedeutet " Nicht abdecken ".
18. Halten Sie brennbares Material wie bel, Kissen,
Bettwäsche, Papier, Kleidung, Vorhänge usw. mindestens
100 cm vom Heizgerät entfernt.
- 18 -
19. Im Innern dieses Heizgeräts befinden sich Teile, die Hitze,
Lichtbögen oder Funken erzeugen können. Nicht in
Bereichen einsetzen, in denen Benzin, Lacke oder
entzündliche Flüssigkeiten verwendet oder gelagert
werden.
20. Bei Nichtgebrauch immer den Netzstecker ziehen.
21. Während des Gebrauch wird das Gerät heiß. Die
ungesctzte Haut vor heißen Flächen fernhalten, es
besteht Verbrennungsgefahr.
22. Die auf dem Gerät angegebene Versorgungsspannung und
Frequenz müssen mit den Werten der verwendeten
Steckdose übereinstimmen. Das Get darf nur an eine
geerdete Steckdose, die in einwandfreiem Zustand und
mit einem Fehlerspannungsschutzschalter mit 30 mA
versehen ist, angeschlossen werden. Die verwendete
Steckdose muss jederzeit gut zugänglich sein, damit der
Stecker in einem Notfall schnell aus der Steckdose
gezogen werden kann.
23. Kabel komplett abwickeln, bevor das Heizgerät mit der
Steckdose verbunden wird. Das Kabel darf mit keinem Teil
des Heizgerätes in Kontakt kommen und muss vor
anderen Hitzequellen geschützt werden, damit es sich
nicht erhitzt. Das Kabel darf nicht unter Teppichen verlegt
werden, nicht mit Matten, ufern oder ähnlichen Dingen
bedeckt werden und nicht in Durchgängen platziert
werden. Es ist darauf zu achten, dass niemand auf das
Kabel treten kann und keine belstücke auf das Kabel
gestellt werden. Das Kabel darf nicht um spitze Ecken
gelegt und nach dem Gebrauch zu fest aufgewickelt
werden.
24. Von der Verwendung eines Verlängerungskabels wird
abgeraten, da sich das Risiko der Überhitzung und eines
Feuers dadurch erhöht. Wenn die Verwendung eines
Verlängerungskabels sich nicht vermeiden sst, sollte ein
unversehrtes, zugelassenes Verlängerungskabel mit einem
Durchmesser von 2 x 1,5 mm2, das r mindestens
1000 Watt Leistung geeignet ist, benutzt werden. Um
Überhitzung zu vermeiden, das Kabel immer vollständig
abwickeln!
- 19 -
25. Das Heizgerät nicht im Freien und nicht in umen unter
7 m³ verwenden.
26. Die Luft in der Umgebung des Heizgeräts muss
ungehindert zirkulieren nnen. Das Heizgerät darf nicht
zu nah an nden oder großen Gegenständen und unter
Regalen, Schnken oder dergleichen aufgestellt werden.
Es muss an allen Seiten ein Abstand von mindestens 30
cm und mindestens 20 cm zum Boden eingehalten
werden. Bei Wandmontage: Den Platz zwischen Heizgerät
und Wand nicht blockieren.
27. Eine sorgfältige Überwachung ist erforderlich, wenn das
Gerät in Anwesenheit von Kindern, behinderten Personen
oder Haustieren benutzt wird. Personen, die das Zimmer
nicht ohne Hilfe verlassen nnen, von dem Heizgerät
wegführen. Die Oberfläche wird sehr heiß (bis zu 95°C). Es
ist deshalb dafür zu sorgen, dass sich Kinder und Personen
mit Behinderungen nicht in der Nähe des Geräts aufhalten.
Verpackungsmaterial von Kindern fernhalten.
28. Heizgerät immer ausschalten, den Stecker aus der
Steckdose ziehen und abkühlen lassen, bevor:
- das Heizgerät gereinigt wird;
- Wartungsarbeiten am Heizgerät vorgenommen werden;
- das Heizgerät berührt oder umgestellt wird.
29. Das Heizgerät ist sauber zu halten. Staub, Schmutz
und/oder Ablagerungen in oder hinter dem Heizgerät sind
eine ufige Ursache von Überhitzung. Diese
Ablagerungen ssen regelmäßig entfernt werden.
30. Das Gerät (inklusive Kabel und Stecker) darf nur von einer
autorisierten Fachkraft geöffnet und/oder repariert
werden.
31. Dieses Heizgerät nur zu seinem Bestimmungszweck und
wie in dieser Bedienungsanleitung beschrieben benutzen.
32. Um Informationen über die Installation zu erhalten, lesen
Sie bitte den nachfolgenden Abschnitt in dieser
Bedienungsanleitung.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58

Emerio CBC-122043.1 Infrared Panel Heater Manuale utente

Categoria
Illuminazione di comodità
Tipo
Manuale utente