Panasonic WVCP160 Istruzioni per l'uso

Marca: Panasonic

Modello: WVCP160

Categoria: Telecamere di sicurezza

Tipo: Istruzioni per l'uso

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

N0300-0 YWV8QA5394AN Printed in Japan

N 19

Panasonic's WV-CP160E colour digital camera introduces a new level of high picture quality

and high resolution through the use of a 1/3-inch interline transfer CCD image sensor having

752 horizontal pixels (picture elements), and digital signal processing LSIs. This model

offers cutting-edge technology for advanced video surveillance. This VP multiplex camera

can be connected with specified monitor by single coaxial cable.

PREFACE

Model No.

WV-CP160E

Colour CCTV Camera

Operating Instructions

(Lens Option)

r D

The serial number of this product may be found

on the top of the unit.

You should note the serial number of this unit

in the space provided and retain this instruction

as a permanent record of your purchase to aid

identification in the event of theft.

Model No.

Serial No.

WARNING:

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER SER-

VICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

Wij verklaren als enige aansprakelijke, dat het product

waarop deze verklaring betrekking heeft, voldoet aan de

normen of andere normatieve documenten, overe-

enkomstig de bepalingen van Richtlijn 89/336/EEC.

Vi erklærer os eneansvarlige for, at dette produkt, som

denne deklaration omhandler, er i overensstemmelse

med standarder eller andre normative dokumenter i følge

bestemmelserne i direktiv 89/336/EEC.

Vi deklarerar härmed värt fulla ansvar för att den produkt

till vilken denna deklaration hänvisar är i överensstäm-

melse med standarddokument, eller andra normativa

dokument som framställs i EEC-direktiv nr. 89/336.

Ilmoitamme yksinomaisella vastuullamme, että tuote, jota

tämä ilmoitus koskee, noudattaa seuraavia standardeja

tai muita ohjeellisia asiakirjoja, jotka noudattavat direkti-

ivin 89/336/EEC säädöksiä.

Vi erklærer oss alene ansvarlige for at produktet som

denne erklæringen gjelder for, er i overensstemmelse

med følgende normer eller andre normgivende doku-

menter som følger bestemmelsene i direktiv 89/336/EEC.

We declare under our sole responsibility that the product

to which this declaration relates is in conformity with the

standards or other normative documents following the

provisions of Directive EEC/89/336.

Dichiariamo sotto nostra esclusiva responsabilità che il

prodotto a cui si riferisce la presente dichiarazione è con-

forme agli standard o altri documenti normativi ottemper-

anti alle disposizioni della direttiva CEE/89/336.

The exclamation point within

an equilateral triangle is intend-

ed to alert the user to the pres-

ence of important operating

and maintenance (servicing)

instructions in the literature

accompanying the appliance.

The lightning flash with arrow-

head symbol, within an equilat-

eral triangle, is interned to alert

the user to the presence of

uninsulated "dangerous volt-

age" within the product's enclo-

sure that may be of sufficient

magnitude to constitute a risk

of electric shock to persons.

1. The following functions are built in.

(1) Auto Light Control (ALC)/Electronic Light Control (ELC)

(2) The SUPER-D2 function eliminates interference by strong background lighting

which makes the camera picture dark, such as a spotlight.

Dynamic range of 48 dB.

(3) Auto/Manual White Balance Function

(4) Electronic Shutter Function

2. Signal-to-noise ratio of 50 dB

3. Minimum illumination of 0.8 lx (0.08 footcandle) with F1.4 lenses.

4. Minimum illumination of 0.4 lx (0.04 footcandle) with Panasonic aspherical high speed

(F0.75) lenses.

5. 480 lines of horizontal resolution

FEATURES

1. Do not attempt to disassemble the camera.

To prevent electric shock, do not remove screws or covers.

There are no user serviceable parts inside. Ask a qualified service person for servicing.

2. Handle the camera with care.

Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged

by improper handling or storage.

3. Do not expose the camera to rain or moisture, or try to operate it in wet areas.

Turn the power off immediately and ask a qualified service person for servicing.

Moisture can damage the camera and also create the danger of electric shock.

4. Do not use strong or abrasive detergents when cleaning the camera body.

Use a dry cloth to clean the camera when dirty.

In case the dirt is hard to remove, use a mild detergent and wipe gently.

PRECAUTIONS

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

q Auto Iris Lens Connector

This connector is used to connect the auto iris lens. It supplies power and DC control

signal to the auto iris lens.

w Flange-back Adjusting Ring

This ring is used to adjust the back focal length or picture focus by rotating it.

e Lens (Option)

r Camera Mounting Screw Hole

This hole is used to mount the camera onto a mounting bracket.

t Focus Fixing Screw

y Down Button ( )

This button is used to move the cursor downward. It is also used to select items in the

CAM SET UP menu.

u Right Button ( )

This button is used to move the cursor to the right. It also selects the mode and can be

used to adjust some levels.

Open the panel to the upper left until it stops by rotating counterclockwise.

Super Dynamic

GP160

q t

MONITOR OUT

MIC OFF-ON

SOFT-SHARP

LOCK

i Left Button ( )

This button is used to move the cursor to the left. It also selects the mode and can be

used to adjust some levels.

o Up Button ( )

This button is used to move the cursor upward. It is also used to select items in the

CAM SET UP menu.

!0 Set Button ( )

This button is used to activate an item selected in the CAM SET UP menu.

!1 Selector (NC)

This selector is not used on this camera.

!2 Detail Level Selector (SOFT-SHARP)

This selector is used to select the detail / aperture level as follows.

SOFT: When a quad system is connected to this camera, select this position.

SHARP: Select this position usually.

!3 Microphone Selector (MIC OFF-ON)

Select ON or OFF as needed.

!4 Microphone

!5 Power indicator

This indicator lights up when the power of this camera is on.

!6 Monitor Output Connector (MONITOR OUT)

This connector is used to connect with the video input connector of the monitor.

!7 Video Output Terminal

This terminal is used to connect with the video input connector of the monitor.

!8 Rear Cover

The rear cover can be removed to gain access to the terminal.

6. High quality picture:

(a) 2H type vertical enhancer for greater picture sharpness

(b) Chroma averaging circuit for better colour signal-to-noise ratio

(d) Expanded dynamic range by use of knee circuit

(e) Highlight aperture correction for greater picture detail of bright objects

7. Ability to shoot indoor scenes with fixed iris lens by use of Electronic Light Control (ELC)

function.

8. Sound around the camera can be monitored by built-in microphone.

5. Clean the CCD faceplate with care.

Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton

tipped applicator and ethanol.

6. Never face the camera towards the sun.

Do not aim the camera at bright objects. Whether the camera is in use or not, never

aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may

be caused.

7. Do not operate the camera beyond the specified temperature or humidity.

Use the camera under conditions where temperature is between –10°C - +50°C (14°F -

122°F), and humidity is below 90%.

Rear Panel

Mounting the Lens

Caution:

Before you mount the lens, loosen the screw on the side of the camera, and rotate the

frange-back adjusting ring clockwise until it stops. If the ring is not at the end, the inner

glass or CCD image sensor may be

damaged.

1. Mount the lens by turning it clockwise

on the lens mount of the camera.

2. Connect the lens cable to the auto iris

lens connector on the side of the cam-

era.

Caution for Mounting the Lens

The lens mount should be a CS-mount (1”-32UN) and the lens weight should be less than

450 g (0.99 lbs). If the lens is heavier, both the lens and camera should be secured by

using the supporter.

The protrusion at the rear of the lens should be as shown below:

CS-mount: Less than 8 mm (5/16”)

The following adjustment should be made by qualified service personnel or system

installers.

1. Loosen the screw on the side of the

camera.

2. Turn the flange-back adjusting ring to

the desired position.

Caution: Do not rotate the ring coun-

terclockwise by force after it stops.

If the ring is rotated by force, the

inner lens or CCD image sensor

may be damaged.

3. Tighten the screw on the side of the

camera.

Cautions:

• Tightening the screw by force will cause damage to the screw or deviation of

focus.

• To use the C-mount lens, the Lens Mount Converter (C-mount adapter) WV-AD20

should be used with the camera.

FOCUS OR FLANGE-BACK ADJUSTMENT

ALC Connector

Screw

Flange-back

Adjusting Ring

Flange-back

Adjusting Ring

Screw

CONNECTIONS

Caution: Keep the POWER switch of the specified monitor, Camera Extension Unit and

Camera Drive Unit in OFF position while making connections. If the power of these units

is ON during connections, the camera does not function due to the built-in protection

circuit which protects it against wrong connections.

Basic System

Connect the coaxial cables between the camera and CAMERA IN connector of the

specified monitor or Camera Drive Unit. The approximate maximum cable length is as

follows:

Coaxial Maximum DC R/300 m (1 000 ft) of

Cable Type Cable Length Inner Conductor

RG-59/U 200 m (660 ft) Less than 30 Ω

RG-6/U 500 m (1 650 ft) Less than 12 Ω

The maximum DC resistance between the camera and these unit is 20 Ω.

Super Dynamic

Colour Monitor

WV-CM143

(Rear Panel)

Coaxial Cable

Cameras

4 3 2 1

CAMERA INPUT

VIDEO OUT VIDEO IN

AUDIO OUT AUDIO IN

OUT

TIMING SELECT

REMOTE OUT

ALARM

CONTROL

SPOT MONITOR CONTROL IN

4321

RESETGNDALL

MODE

STDBY

4321

GNDRECOVER

CAMERA

EXTENSION IN

FOCUS

CAMERA POWER

OFF

Following explanation for installing the camera mounting bracket is for the installation on the

wall, but also applies equally to the installation on the ceiling, a shelf and stand.

1. Install the camera mounting bracket on

the wall with 2 screws.

Note: The coaxial cable can be

passed through the center hole of

the camera mounting bracket.

2. Insert the camera fixing screw into the

camera mounting hole and tighten the

screw firmly.

Camera Mounting Bracket

Fixing Screws

The mounting bracket can be fixed either on the top or bottom cover of the camera.

• Mounting from the top

Remove the mount adapter from the bot-

tom of the camera by removing the two fix-

ing screws. The mounting hole is a stan-

dard photographic pan-head screw size

(1/4” - 20). Attach the mount adapter to the

top as shown in the diagram, then mount

the camera on the mounting bracket.

Make sure that the two original fixing

screws are used when mounting the mount

adapter as longer length screws may dam-

age inner components.

INSTALLATION OF CAMERA

3. Connect the camera and monitor with

the coaxial cable and turn on the

power switch of the monitor.

4. While viewing the monitor picture,

loosen the angular control screw slight-

ly. Adjust the camera’s angle to the

desired position, and then tighten the

screw firmly.

Angular Control Screw

INSTALLATION PROCEDURE

Diam. 120

(Diam. 4-3/4)

90°

15 (9/16) 85 (3-3/8) 40 (1-9/16)

5 (3/16)

6.5 (1/4)

164 (6-7/16)

2-Diam. 5 (2-Diam. 3/16)

83.5 (3-5/16)

Caution on installation

Use wood screws with the cam-

era mounting bracket that are

suitable for Installation into a

wood base of appropriate

dimensions and strength. For

installation in a material other

than wood, refer servicing to

qualified service personnel.

Unit : mm (inch)

DIMENSIONS OF MOUNTING BRACKET

Fixing Screws

Mount Adaptor

Coaxial Cable

Fixing Screws

Camera Mounting

Bracket

1. CAMERA SETUP MENU

This camera utilizes a user setup menu that is displayed on-screen.

• Opening the Setup Menu

Press and hold down for 2 seconds or

more.

The CAM SET UP menu appears on the

monitor as shown at right.

Check the current settings on the menu.

Refer to the sections below for a detailed description of menu items. If you decide not to

make any changes after checking the current settings, move the cursor to END at the start

of the bottom line, and press to close the CAM SET UP menu and return to normal cam-

era picture mode.

Note: If no button is pressed for 6 minutes while the CAM SET UP menu or any other menu

is opened, the menu is automatically closed and the mode returns to the normal cam-

era picture.

2. SETUP OPERATION

This camera utilizes a user setup menu

(CAM SET UP) that is displayed on the

monitor.

To set items on the CAM SET UP menu, use

the following buttons on the side panel.

Up Button (): Moves the cursor

upwards. Use this button to select an item or adjust the parameters.

Down Button (): Moves the cursor downwards. Use this button to select an item or

adjust the parameters.

Right Button (): Moves the cursor to the right. Use this button to select or adjust the

parameters of the selected item. The parameter changes each time

this button is pressed.

Left Button (): Moves the cursor to the left. Use this button to select or adjust the

parameters of the selected item. The parameter changes each time

this button is pressed.

Set Button (): Executes selections and displays a submenu for an item with mark.

END: Close Setup menu.

RET: Return to the previous menu.

To return to the CAM SET UP menu

Move the cursor to RET and press . The CAM SET UP menu appears.

• All Reset Operation

All Reset allows you to reset all setup menu items to the factory default settings if you are

unsure about the correct settings. Proceed as follows:

(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).

(2) While pressing both and , press for a few seconds. The message ALL

RESET momentarily appears on the monitor.

This resets all adjustments and parameters to the factory default settings.

• Editing the CAM SET UP Menu

Important Notice:

When the SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you

cannot change the currently active settings. This is to prevent accidental changing of

the settings.

To edit the CAM SET UP menu (change

settings), press and or and

to move the cursor to SET UP DIS-

ABLE in the bottom line.

Press . SET UP DISABLE changes

to SET UP ENABLE. Move the cursor to

END, then to the item(s) you want to

change.

• Editing the SPECIAL Menu

To edit the SPECIAL menu (change set-

tings), proceed as for editing the CAM SET

UP menu above. Move the cursor to END

after the SET UP ENABLE appears. Then

press and simultaneously (holding

down and press ) for 2 seconds or

more.

The SPECIAL menu appears on the moni-

tor. Select the item to be changed and

change the setting as described for the

CAM SET UP menu.

Important Notice:

When the cursor is moved to END and the CAM SET UP menu closed after changing

the parameters, the new values are saved in the EEPROM (Electric Erasable and

Programmable Read Only Memory). These values remain valid until new values are

saved, even if the power of the camera is off.

↵

Left Button

Right

Button

Down

Button

** CAM SET UP **

CAMERA ID OFF

ALC/ELC ALC

SHUTTER OFF

AGC ON

SENS UP OFF

WHITE BAL ATW

AUDIO LEVEL ....I....

- +

END SET UP DISABLE

↵↵↵

** CAM SET UP **

CAMERA ID OFF

ALC/ELC ALC

SHUTTER OFF

AGC ON

SENS UP OFF

WHITE BAL ATW

AUDIO LEVEL ....I....

- +

END SET UP ENABLE

↵↵↵

SETUP

↵↵↵

** CAM SET UP **

CAMERA ID OFF

ALC/ELC ALC

SHUTTER OFF

AGC ON

SENS UP OFF

WHITE BAL ATW

AUDIO LEVEL ....I....

- +

END SET UP DISABLE

Highlighted

(To be continued reverse page)

** SPECIAL **

UP SIDE DOWN OFF

CHROMA GAIN ....I....

AP SHARP ....I....

PEDESTAL .I.......

- +

CAMERA RESET PUSH SW

RET END

Set Button

2. Move the CAMERA ID to the desired

position by pressing / / / .

3. Press to fix the position of the

CAMERA ID. The mode returns to the

previous CAMERA ID menu.

Notes:

• The CAMERA ID stops at the edges of the monitor screen.

• The CAMERA ID moves faster if any of / / / is kept pressed for a sec-

ond or more.

2. Light Control Setting (ALC/ELC)

You can select the light control mode accord-

ing to the lens type.

ALC: If you use the auto iris lens, select this

parameter.

ELC: If you use a fixed or manual iris lens,

select this parameter.

1. Move the cursor to the ALC/ELC parame-

ter.

2. Select ALC or ELC.

2-1. ALC Mode with SUPER-D2 ON

Super Dynamic 2 Function (SUPER-D2)

The important object in a scene is usually placed in the center of the monitor’s screen. In

SUPER-D2 mode, the dynamic range is 64 times greater than a conventional camera. This

allows you to see all the details on the monitor, even under difficult lighting condition. You

can use the SUPER-D2 function if you select ALC.

1. After selecting ALC, press to open

the ALC CONT menu.

2. Move the cursor to the SUPER-D2

parameter and select ON.

3. If you want to adjust the video output

level, move the cursor to the "I" posi-

tion. Adjust to the desired level by

pressing or .

SETTING PROCEDURES

** ALC CONT **

BACK LIGHT COMP

SUPER-D2 OFF

MASK SET

LEVEL ...I.....

- +

RET END

↵

** ALC CONT **

BACK LIGHT COMP

SUPER-D2 ON

LEVEL ...I.....

- +

RET END

1. Camera Identification (CAMERA ID) Setting

You can use the camera identification (CAMERA ID) to assign a name to the camera. The

camera ID consists of up to 16 alphanumeric characters. The camera ID display can be

selected on or off on the monitor screen.

To edit the CAMERA ID

1. Move the cursor to the CAMERA ID parameter.

2. Press . The CAMERA ID menu appears. The cursor on the letter “0” is highlighted.

3. Move the cursor to the character you

want to edit by pressing / / /

4. After selecting the character, press

. The selected character appears

in the editing area. (The pointer in the

editing area moves to the right auto-

matically at this moment.)

5. Repeat the steps above until all char-

acters are edited.

To enter a blank space in the CAMERA ID

Move the cursor to SPACE and press .

To replace a specific character in the CAMERA ID

1. Move the cursor to the editing area by pressing

2. Move the pointer to the character to be replaced by pressing or . Then move

the cursor to the character area and select a new character.

3. Press to determine the CAMERA ID.

To erase all characters in the editing area

Move the cursor to RESET and press . All characters in the editing area disappear.

To determine the display position of the CAMERA ID

1. Move the cursor to POSI, and press

. The display shown below ap-

pears and the CAMERA ID is highlight-

ed.

WV-CP160

Highlighted

0123456789

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

().,'":;&#!?=

+-*/%$ÄÜÖÆÑÅ

SPACE

POSI RET END RESET

................

Character Cursor

Pointer

Character

Area

Command

Editing

Area

CAMERA ID menu

** CAM SET UP **

CAMERA ID OFF

ALC/ELC ALC

SHUTTER OFF

AGC ON

SENS UP OFF

WHITE BAL ATW

AUDIO LEVEL ....I....

- +

END SET UP ENABLE

↵↵↵

** CAM SET UP **

CAMERA ID OFF

ALC/ELC ALC

SHUTTER OFF

AGC ON

SENS UP OFF

WHITE BAL ATW

AUDIO LEVEL ....I....

- +

END SET UP ENABLE

↵↵↵

2-2. ALC Mode with SUPER-D2 OFF and ELC Mode

Note: If ELC is selected, set MASK SET according to this procedure.

1. Move the cursor to the SUPER-D2

parameter and select OFF. (When you

select ELC, SUPER-D2 is not avail-

able.) The item MASK SET appears on

the menu.

2. Move the cursor to MASK SET and

press . 48 mask areas appear on

the monitor screen. The cursor is blink-

ing in the upper left corner of the

screen.

3. Move the cursor to the area where

backlight is bright and press to

mask that area. The mask turns to

white. (When the cursor is moved on

an area that has already been masked,

the mask and cursor start blinking.)

4. Repeat step 3 to mask the desired

area. To cancel masking, move the

cursor to that area and press .

5. After masking is completed, press

for 2 seconds or more. The ALC CONT

menu appears.

6. If you want to change the video output

level (picture contrast), move the “I”

cursor for LEVEL and adjust the level.

Note: If ON is selected for the SUPER-D2 parameter, a shadow (black line) may appear at

the boundary between the bright and the dim scene. This is a natural phenomenon and

does not indicate trouble.

3. Shutter Speed (SHUTTER)

Move the cursor to the SHUTTER parame-

ter and select the electronic shutter speed.

The preset values for SHUTTER change by

pressing or as shown right.

Note: When ELC is selected for ALC/ELC or ON is selected for SUPER-D2, this item is not

available.

4. Gain Control Setting (AGC ON/OFF)

You can set the gain (brightness level por-

tion of an image) to automatic level adjust-

ment (ON) or fixed level (OFF).

Move the cursor to the AGC parameter and

select automatic level adjustment (ON) or

fixed level (OFF).

Note: If ON is selected for the AGC para-

meter, the noise reduction function is

automatically activated under low light

conditions to reduce noise. In pictures containing a moving object, this may result in an

afterimage.

5. Electronic Sensitivity Enhancement (SENS UP)

There are two modes for SENS UP.

AUTO: If you select X10 AUTO, for

example, the sensitivity is raised

automatically to X10 max. When

AUTO is selected, AGC is auto-

matically set to ON.

FIX: If you select X32 FIX, for example,

the sensitivity is raised to just X32.

Move the cursor to the SENS UP parameter and select the parameter for electronic sensitivi-

ty enhancement.

The preset values for SENS UP (electronic sensitivity enhancement) change by pressing

or as shown at right:

• When OFF is selected for

SUPER-D2 on the CAM SET UP

menu.

• When ON is selected for

SUPER-D2 on the CAM SET UP

menu.

Notes:

• When ON is selected for SUPER-D2 in the ALC CONT menu, FIX is not available for this

item.

• When you select AUTO for SENS UP and ON for SUPER-D2, the SENS UP function has

priority so that the SUPER-D2 function is not activated automatically.

• While the SENS UP function is selected, noise, spots or a whitish phenomenon may

appear in the picture when the sensitivity of the camera is increased. This is a normal

phenomenon.

X2 AUTO

OFF

X4 AUTO X6 AUTO X10 AUTO

X32 FIX X10 FIX X6 FIX X4 FIX X2 FIX

OFF

X16 FIX

** ALC CONT **

BACK LIGHT COMP

SUPER-D2 OFF

MASK SET

LEVEL ...I.....

- +

RET END

↵

Blinking

Turns to white

** CAM SET UP **

CAMERA ID OFF

ALC/ELC ALC

SHUTTER OFF

AGC ON

SENS UP OFF

WHITE BAL ATW

AUDIO LEVEL ....I....

- +

END SET UP ENABLE

↵↵

↵

** CAM SET UP **

CAMERA ID OFF

ALC/ELC ALC

SHUTTER OFF

AGC ON

SENS UP OFF

WHITE BAL ATW

AUDIO LEVEL ....I....

- +

END SET UP ENABLE

↵↵↵

OFF

X2AUTO

X10AUTO

X6AUTO

X4AUTO

OFF (1/50) 1/120

1/10000 1/4000 1/2000 1/1000

1/250 1/500

6. White Balance Setting (WHITE BAL)

6-1. Auto-Tracing White Balance Mode (ATW)

You can select one of two modes for white balance adjustment as follows:

• ATW (Auto Tracing White Balance)

In this mode, the colour temperature is monitored continuously and thereby white bal-

ance is set automatically. The colour temperature range for the proper white balance is

approximately 2 600 - 6 000K. Proper white balance may not be obtained under the fol-

lowing conditions:

1. The colour temperature is out of

the 2 600 - 6 000K range.

2. When the scene contains mostly

high colour temperature objects,

such as a blue sky or sunset.

3. When the scene is dim.

In these cases, select the AWC

mode.

Move the cursor to the WHITE BAL

parameter and select ATW. The

white balance of the camera is

automatically set.

• Automatic White Balance Control Mode (AWC)

In this mode, accurate white balance is obtained within a colour temperature range of

approximately 2 300-10 000K.

1. Move the cursor to the WHITE BAL

parameter and select AWC→PUSH

SW.

2. Press to start the white bal-

ance setup. The PUSH SW is high-

lighted to indicate that the white

balance is being set.

3. When the white balance setting is completed, the PUSH SW returns to normal dis-

play.

Note: In case that the white balance is not set, the PUSH SW is being highlighted.

4. When you want to adjust the white balance manually, press to select AWC and

press . The AWC menu appears on the monitor. (When ATW is selected, press-

ing displays the ATW menu.)

Fine Adjustment for AWC (ATW) Manually

You can add the detailed setting for white balance setting manually.

1. To set MASK SET, proceed as described in steps 2 to 4 of “ALC mode with SUPER-D2

OFF and ELC mode”.

2. Move the cursor to R.

3. Press or to obtain the optimum amount of red gain.

4. Move the cursor to B.

5. Press or to obtain the optimum amount of blue gain.

Note: When you need to set MASK SET, re-adjust to obtain the optimum amount of red and

blue gain.

7. Audio Level Control (MIC. ON/OFF)

This item is used to adjust the audio level of the sound from microphone.

When the Microphone Selector is set to ON, this function is available.

1. Move the cursor to the AUDIO LEVEL

parameter.

2. Move the “I” cursor to adjust the audio

level.

** CAM SET UP **

CAMERA ID OFF

ALC/ELC ALC

SHUTTER OFF

AGC ON

SENS UP OFF

WHITE BAL ATW

AUDIO LEVEL ....I....

- +

END SET UP ENABLE

↵↵↵

** CAM SET UP **

CAMERA ID OFF

ALC/ELC ALC

SHUTTER OFF

AGC ON

SENS UP OFF

WHITE BAL AWC

→

PUSH SW

AUDIO LEVEL ....I....

- +

END SET UP ENABLE

↵↵

** CAM SET UP **

CAMERA ID OFF

ALC/ELC ALC

SHUTTER OFF

AGC ON

SENS UP OFF

WHITE BAL AWC

→

PUSH SW

AUDIO LEVEL ....I....

- +

END SET UP ENABLE

↵↵

** CAM SET UP **

CAMERA ID OFF

ALC/ELC ALC

SHUTTER OFF

AGC ON

SENS UP OFF

WHITE BAL AWC

AUDIO LEVEL ....I....

- +

END SET UP ENABLE

↵↵↵

** AWC **

R ....I....

- +

B ....I....

- +

MASK SET

RET END

↵

** CAM SET UP **

CAMERA ID OFF

ALC/ELC ALC

SHUTTER OFF

AGC ON

SENS UP OFF

WHITE BAL ATW

AUDIO LEVEL ....I....

- +

END SET UP ENABLE

↵↵↵

8. Special Menu

This menu lets you adjust and set

up the video signal of the camera

to meet your requirements.

Move the cursor to END on the

bottom line of the CAM SET UP

menu and press and

simultaneously (holding down

and press ) for 2 seconds or

more. The SPECIAL menu ap-

pears on the monitor as shown at

right.

8-1. Camera Picture Upside Down Positioning (UP SIDE DOWN)

1. Move the cursor to the UP SIDE DOWN parameter.

2. Select ON when you desire to turn the picture upside down.

8-2. Chroma Level Setting (CHROMA GAIN)

1. Move the cursor to the CHROMA GAIN parameter.

2. While observing the vectorscope or colour video monitor, move the “I” cursor to adjust

the chroma level.

8-3. Aperture Sharpness (Softness) Setting (AP SHARP/AP SOFT)

Note: This item changes according to the position of the detail level selector

(SOFT/SHARP) on the side of the camera.

1. Move the cursor to the AP SHARP (AP SOFT) parameter.

2. While observing the colour video monitor, move the “I” cursor to adjust the aperture

gain level.

8-4. Pedestal Level Setting (PEDESTAL)

1. Move the cursor to the PEDESTAL parameter.

2. While observing the waveform monitor or colour video monitor, move the “I” cursor to

adjust the pedestal level (black level).

To reset to the factory settings (CAMERA RESET)

1. Move the cursor to the CAMERA RESET parameter. PUSH SW is highlighted.

2. While holding down and , press for 2 seconds or more. The camera is reset

to the factory settings.

To close the SPECIAL menu and return to the CAM SET UP menu

Move the cursor to RET and press .

To close the SPECIAL menu and return to the camera picture

Move the cursor to END and press .

** SPECIAL **

UP SIDE DOWN OFF

CHROMA GAIN ....I....

AP SHARP ....I....

PEDESTAL .I.......

CAMERA RESET PUSH SW

RET END

** CAM SET UP **

CAMERA ID OFF

ALC/ELC ALC

SHUTTER OFF

AGC ON

SENS UP OFF

WHITE BAL ATW

AUDIO LEVEL ....I....

- +

END SET UP ENABLE

↵↵↵

Pick-up Device: 752 (H) x 582 (V) pixels, Interline Transfer CCD

Scanning Area: 4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of

1/3” pick-up tube)

Scanning: 625 lines/50 fields/25 frames

Horizontal: 15.625 kHz

Vertical: 50 Hz

Synchronization: Multiplexed Vertical Drive (VD2) by use of specified

camera drive unit.

Video Output: 1.0 V[p-p] PAL composite 75 Ω/through

camera drive unit

Horizontal Resolution: 480 lines

Signal-to-Noise Ratio: 50 dB (AGC OFF, weight ON)

Dynamic Range: 48 dB

Minimum Illumination: 0.4 lx (0.04 footcandle) at F0.75 [Equivalent to 0.8 lx

(0.08 footcandle) at F1.4]

Gain Control: AGC ON or OFF (SET UP MENU) selectable

White Balance: ATW or AWC (SET UP MENU) selectable

Aperture: Set Variable (SET UP MENU) Sharp-Soft selectable by

detail level selector

Electronic Light Control: ALC/ELC

Super Dynamic2: ON or OFF (SET UP MENU) selectable

Electronic Shutter Speed: 1/50 (OFF), 1/120 1/250, 1/500, 1/1 000 1/2 000,

1/4 000, 1/10 000 s selectable

Lens Mount: CS-mount

ALC Lens: DC drive

Ambient Operating Temperature: –10°C - +50°C (14°F - 122°F)

Ambient Operating Humidity: Less than 90 %

Power Source: From the specified monitor or camera drive unit

Power Consumption: 350 mA

Dimensions (without lens): 68 (W) x 65 (H) x 126 (D) mm

[2-11/16” (W) x 2-9/16” (H) x 4-15/16” (D)]

Weights (without lens): 0.375 kg (0.8 lbs.)

Weights and dimensions indicated are approximate.

Specifications are subject to change without notice.

SPECIFICATIONS

OPTIONAL ACCESSORIES

Lenses : WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3,

WV-LA908C3, WV-LZ61/10, WV-LZ61/15, WV-LZ60/2, WV-LZ62/8

STANDARD ACCESSORIES

Body Cap.......................................................................1 pc.

Camera Mounting Bracket.............................................1 pc.

When the camera is aimed at a bright light, such as a spotlight, or a surface that reflects

bright light, smear or blooming may appear. Therefore, the camera should be operated

carefully in the vicinity of extremely bright objects to avoid smear or blooming.

Bright object

Smear

PREVENTION OF BLOOMING AND SMEAR

Matsushita Electric Industrial Co., Ltd.

Central P.O. Box 288, Osaka 530-91, Japan

Panasonic WVCP160 Istruzioni per l'uso

Marca: Panasonic

Modello: WVCP160

Categoria: Telecamere di sicurezza

Tipo: Istruzioni per l'uso

Scarica PDF

rapporto

in altre lingue

English: Panasonic WVCP160 Operating instructions

Panasonic WVCP160 Istruzioni per l'uso

Panasonic WVCP160 Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti