Panasonic WVCP160 Istruzioni per l'uso
- Categoria
- Telecamere di sicurezza
- Tipo
- Istruzioni per l'uso
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
N0300-0 YWV8QA5394AN Printed in Japan
N 19
Panasonic's WV-CP160E colour digital camera introduces a new level of high picture quality
and high resolution through the use of a 1/3-inch interline transfer CCD image sensor having
752 horizontal pixels (picture elements), and digital signal processing LSIs. This model
offers cutting-edge technology for advanced video surveillance. This VP multiplex camera
can be connected with specified monitor by single coaxial cable.
PREFACE
Model No.
WV-CP160E
Colour CCTV Camera
Operating Instructions
(Lens Option)
S
u
p
e
r D
y
n
am
ic
The serial number of this product may be found
on the top of the unit.
You should note the serial number of this unit
in the space provided and retain this instruction
as a permanent record of your purchase to aid
identification in the event of theft.
Model No.
Serial No.
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SER-
VICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
Wij verklaren als enige aansprakelijke, dat het product
waarop deze verklaring betrekking heeft, voldoet aan de
normen of andere normatieve documenten, overe-
enkomstig de bepalingen van Richtlijn 89/336/EEC.
Vi erklærer os eneansvarlige for, at dette produkt, som
denne deklaration omhandler, er i overensstemmelse
med standarder eller andre normative dokumenter i følge
bestemmelserne i direktiv 89/336/EEC.
Vi deklarerar härmed värt fulla ansvar för att den produkt
till vilken denna deklaration hänvisar är i överensstäm-
melse med standarddokument, eller andra normativa
dokument som framställs i EEC-direktiv nr. 89/336.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota
tämä ilmoitus koskee, noudattaa seuraavia standardeja
tai muita ohjeellisia asiakirjoja, jotka noudattavat direkti-
ivin 89/336/EEC säädöksiä.
Vi erklærer oss alene ansvarlige for at produktet som
denne erklæringen gjelder for, er i overensstemmelse
med følgende normer eller andre normgivende doku-
menter som følger bestemmelsene i direktiv 89/336/EEC.
We declare under our sole responsibility that the product
to which this declaration relates is in conformity with the
standards or other normative documents following the
provisions of Directive EEC/89/336.
Dichiariamo sotto nostra esclusiva responsabilità che il
prodotto a cui si riferisce la presente dichiarazione è con-
forme agli standard o altri documenti normativi ottemper-
anti alle disposizioni della direttiva CEE/89/336.
The exclamation point within
an equilateral triangle is intend-
ed to alert the user to the pres-
ence of important operating
and maintenance (servicing)
instructions in the literature
accompanying the appliance.
The lightning flash with arrow-
head symbol, within an equilat-
eral triangle, is interned to alert
the user to the presence of
uninsulated "dangerous volt-
age" within the product's enclo-
sure that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.
1. The following functions are built in.
(1) Auto Light Control (ALC)/Electronic Light Control (ELC)
(2) The SUPER-D2 function eliminates interference by strong background lighting
which makes the camera picture dark, such as a spotlight.
Dynamic range of 48 dB.
(3) Auto/Manual White Balance Function
(4) Electronic Shutter Function
2. Signal-to-noise ratio of 50 dB
3. Minimum illumination of 0.8 lx (0.08 footcandle) with F1.4 lenses.
4. Minimum illumination of 0.4 lx (0.04 footcandle) with Panasonic aspherical high speed
(F0.75) lenses.
5. 480 lines of horizontal resolution
FEATURES
1. Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws or covers.
There are no user serviceable parts inside. Ask a qualified service person for servicing.
2. Handle the camera with care.
Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged
by improper handling or storage.
3. Do not expose the camera to rain or moisture, or try to operate it in wet areas.
Turn the power off immediately and ask a qualified service person for servicing.
Moisture can damage the camera and also create the danger of electric shock.
4. Do not use strong or abrasive detergents when cleaning the camera body.
Use a dry cloth to clean the camera when dirty.
In case the dirt is hard to remove, use a mild detergent and wipe gently.
PRECAUTIONS
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
q Auto Iris Lens Connector
This connector is used to connect the auto iris lens. It supplies power and DC control
signal to the auto iris lens.
w Flange-back Adjusting Ring
This ring is used to adjust the back focal length or picture focus by rotating it.
e Lens (Option)
r Camera Mounting Screw Hole
This hole is used to mount the camera onto a mounting bracket.
t Focus Fixing Screw
y Down Button ( )
This button is used to move the cursor downward. It is also used to select items in the
CAM SET UP menu.
u Right Button ( )
This button is used to move the cursor to the right. It also selects the mode and can be
used to adjust some levels.
Open the panel to the upper left until it stops by rotating counterclockwise.
Super Dynamic
Super Dynamic
W
V
-
G
P
1
6
0
GP160
q t
y
!3
!0
o
u
i
w
r
e
!5
!8
!1
!2
MONITOR OUT
NC
MIC OFF-ON
SOFT-SHARP
LOCK
!6
!7
!4
i Left Button ( )
This button is used to move the cursor to the left. It also selects the mode and can be
used to adjust some levels.
o Up Button ( )
This button is used to move the cursor upward. It is also used to select items in the
CAM SET UP menu.
!0 Set Button ( )
This button is used to activate an item selected in the CAM SET UP menu.
!1 Selector (NC)
This selector is not used on this camera.
!2 Detail Level Selector (SOFT-SHARP)
This selector is used to select the detail / aperture level as follows.
SOFT: When a quad system is connected to this camera, select this position.
SHARP: Select this position usually.
!3 Microphone Selector (MIC OFF-ON)
Select ON or OFF as needed.
!4 Microphone
!5 Power indicator
This indicator lights up when the power of this camera is on.
!6 Monitor Output Connector (MONITOR OUT)
This connector is used to connect with the video input connector of the monitor.
!7 Video Output Terminal
This terminal is used to connect with the video input connector of the monitor.
!8 Rear Cover
The rear cover can be removed to gain access to the terminal.
6. High quality picture:
(a) 2H type vertical enhancer for greater picture sharpness
(b) Chroma averaging circuit for better colour signal-to-noise ratio
(c) Minimum of aliasing on fine objects
(d) Expanded dynamic range by use of knee circuit
(e) Highlight aperture correction for greater picture detail of bright objects
7. Ability to shoot indoor scenes with fixed iris lens by use of Electronic Light Control (ELC)
function.
8. Sound around the camera can be monitored by built-in microphone.
5. Clean the CCD faceplate with care.
Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton
tipped applicator and ethanol.
6. Never face the camera towards the sun.
Do not aim the camera at bright objects. Whether the camera is in use or not, never
aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may
be caused.
7. Do not operate the camera beyond the specified temperature or humidity.
Use the camera under conditions where temperature is between –10°C - +50°C (14°F -
122°F), and humidity is below 90%.
Rear Panel
Mounting the Lens
Caution:
Before you mount the lens, loosen the screw on the side of the camera, and rotate the
frange-back adjusting ring clockwise until it stops. If the ring is not at the end, the inner
glass or CCD image sensor may be
damaged.
1. Mount the lens by turning it clockwise
on the lens mount of the camera.
2. Connect the lens cable to the auto iris
lens connector on the side of the cam-
era.
Caution for Mounting the Lens
The lens mount should be a CS-mount (1”-32UN) and the lens weight should be less than
450 g (0.99 lbs). If the lens is heavier, both the lens and camera should be secured by
using the supporter.
The protrusion at the rear of the lens should be as shown below:
CS-mount: Less than 8 mm (5/16”)
The following adjustment should be made by qualified service personnel or system
installers.
1. Loosen the screw on the side of the
camera.
2. Turn the flange-back adjusting ring to
the desired position.
Caution: Do not rotate the ring coun-
terclockwise by force after it stops.
If the ring is rotated by force, the
inner lens or CCD image sensor
may be damaged.
3. Tighten the screw on the side of the
camera.
Cautions:
• Tightening the screw by force will cause damage to the screw or deviation of
focus.
• To use the C-mount lens, the Lens Mount Converter (C-mount adapter) WV-AD20
should be used with the camera.
FOCUS OR FLANGE-BACK ADJUSTMENT
ALC Connector
Screw
Flange-back
Adjusting Ring
Flange-back
Adjusting Ring
Screw
CONNECTIONS
Caution: Keep the POWER switch of the specified monitor, Camera Extension Unit and
Camera Drive Unit in OFF position while making connections. If the power of these units
is ON during connections, the camera does not function due to the built-in protection
circuit which protects it against wrong connections.
Basic System
Connect the coaxial cables between the camera and CAMERA IN connector of the
specified monitor or Camera Drive Unit. The approximate maximum cable length is as
follows:
Coaxial Maximum DC R/300 m (1 000 ft) of
Cable Type Cable Length Inner Conductor
RG-59/U 200 m (660 ft) Less than 30 Ω
RG-6/U 500 m (1 650 ft) Less than 12 Ω
The maximum DC resistance between the camera and these unit is 20 Ω.
Super Dynamic
Super Dynamic
Super Dynamic
Super Dynamic
Colour Monitor
WV-CM143
(Rear Panel)
Coaxial Cable
Coaxial Cable
Coaxial Cable
Coaxial Cable
Cameras
4 3 2 1
CAMERA INPUT
VIDEO OUT VIDEO IN
AUDIO OUT AUDIO IN
OUT
TIMING SELECT
IN
REMOTE OUT
ALARM
CONTROL
SPOT MONITOR CONTROL IN
4321
RESETGNDALL
MODE
STDBY
4321
GNDRECOVER
CAMERA
EXTENSION IN
FOCUS
CAMERA POWER
ON
OFF
Following explanation for installing the camera mounting bracket is for the installation on the
wall, but also applies equally to the installation on the ceiling, a shelf and stand.
1. Install the camera mounting bracket on
the wall with 2 screws.
Note: The coaxial cable can be
passed through the center hole of
the camera mounting bracket.
2. Insert the camera fixing screw into the
camera mounting hole and tighten the
screw firmly.
Camera Mounting Bracket
Fixing Screws
The mounting bracket can be fixed either on the top or bottom cover of the camera.
• Mounting from the top
Remove the mount adapter from the bot-
tom of the camera by removing the two fix-
ing screws. The mounting hole is a stan-
dard photographic pan-head screw size
(1/4” - 20). Attach the mount adapter to the
top as shown in the diagram, then mount
the camera on the mounting bracket.
Make sure that the two original fixing
screws are used when mounting the mount
adapter as longer length screws may dam-
age inner components.
INSTALLATION OF CAMERA
3. Connect the camera and monitor with
the coaxial cable and turn on the
power switch of the monitor.
4. While viewing the monitor picture,
loosen the angular control screw slight-
ly. Adjust the camera’s angle to the
desired position, and then tighten the
screw firmly.
Angular Control Screw
INSTALLATION PROCEDURE
Diam. 120
(Diam. 4-3/4)
90°
15 (9/16) 85 (3-3/8) 40 (1-9/16)
5 (3/16)
6.5 (1/4)
164 (6-7/16)
2-Diam. 5 (2-Diam. 3/16)
83.5 (3-5/16)
Caution on installation
Use wood screws with the cam-
era mounting bracket that are
suitable for Installation into a
wood base of appropriate
dimensions and strength. For
installation in a material other
than wood, refer servicing to
qualified service personnel.
Unit : mm (inch)
DIMENSIONS OF MOUNTING BRACKET
Fixing Screws
Mount Adaptor
Coaxial Cable
Fixing Screws
Camera Mounting
Bracket
1. CAMERA SETUP MENU
This camera utilizes a user setup menu that is displayed on-screen.
• Opening the Setup Menu
Press and hold down for 2 seconds or
more.
The CAM SET UP menu appears on the
monitor as shown at right.
Check the current settings on the menu.
Refer to the sections below for a detailed description of menu items. If you decide not to
make any changes after checking the current settings, move the cursor to END at the start
of the bottom line, and press to close the CAM SET UP menu and return to normal cam-
era picture mode.
Note: If no button is pressed for 6 minutes while the CAM SET UP menu or any other menu
is opened, the menu is automatically closed and the mode returns to the normal cam-
era picture.
2. SETUP OPERATION
This camera utilizes a user setup menu
(CAM SET UP) that is displayed on the
monitor.
To set items on the CAM SET UP menu, use
the following buttons on the side panel.
Up Button (): Moves the cursor
upwards. Use this button to select an item or adjust the parameters.
Down Button (): Moves the cursor downwards. Use this button to select an item or
adjust the parameters.
Right Button (): Moves the cursor to the right. Use this button to select or adjust the
parameters of the selected item. The parameter changes each time
this button is pressed.
Left Button (): Moves the cursor to the left. Use this button to select or adjust the
parameters of the selected item. The parameter changes each time
this button is pressed.
Set Button (): Executes selections and displays a submenu for an item with mark.
END: Close Setup menu.
RET: Return to the previous menu.
To return to the CAM SET UP menu
Move the cursor to RET and press . The CAM SET UP menu appears.
• All Reset Operation
All Reset allows you to reset all setup menu items to the factory default settings if you are
unsure about the correct settings. Proceed as follows:
(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).
(2) While pressing both and , press for a few seconds. The message ALL
RESET momentarily appears on the monitor.
This resets all adjustments and parameters to the factory default settings.
• Editing the CAM SET UP Menu
Important Notice:
When the SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you
cannot change the currently active settings. This is to prevent accidental changing of
the settings.
To edit the CAM SET UP menu (change
settings), press and or and
to move the cursor to SET UP DIS-
ABLE in the bottom line.
Press . SET UP DISABLE changes
to SET UP ENABLE. Move the cursor to
END, then to the item(s) you want to
change.
• Editing the SPECIAL Menu
To edit the SPECIAL menu (change set-
tings), proceed as for editing the CAM SET
UP menu above. Move the cursor to END
after the SET UP ENABLE appears. Then
press and simultaneously (holding
down and press ) for 2 seconds or
more.
The SPECIAL menu appears on the moni-
tor. Select the item to be changed and
change the setting as described for the
CAM SET UP menu.
Important Notice:
When the cursor is moved to END and the CAM SET UP menu closed after changing
the parameters, the new values are saved in the EEPROM (Electric Erasable and
Programmable Read Only Memory). These values remain valid until new values are
saved, even if the power of the camera is off.
↵
Left Button
Right
Button
Down
Button
Up
Button
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
- +
END SET UP DISABLE
↵↵↵
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
- +
END SET UP ENABLE
↵↵↵
SETUP
↵↵↵
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
- +
END SET UP DISABLE
Highlighted
(To be continued reverse page)
** SPECIAL **
UP SIDE DOWN OFF
CHROMA GAIN ....I....
AP SHARP ....I....
PEDESTAL .I.......
- +
CAMERA RESET PUSH SW
RET END
Set Button
2. Move the CAMERA ID to the desired
position by pressing / / / .
3. Press to fix the position of the
CAMERA ID. The mode returns to the
previous CAMERA ID menu.
Notes:
• The CAMERA ID stops at the edges of the monitor screen.
• The CAMERA ID moves faster if any of / / / is kept pressed for a sec-
ond or more.
2. Light Control Setting (ALC/ELC)
You can select the light control mode accord-
ing to the lens type.
ALC: If you use the auto iris lens, select this
parameter.
ELC: If you use a fixed or manual iris lens,
select this parameter.
1. Move the cursor to the ALC/ELC parame-
ter.
2. Select ALC or ELC.
2-1. ALC Mode with SUPER-D2 ON
Super Dynamic 2 Function (SUPER-D2)
The important object in a scene is usually placed in the center of the monitor’s screen. In
SUPER-D2 mode, the dynamic range is 64 times greater than a conventional camera. This
allows you to see all the details on the monitor, even under difficult lighting condition. You
can use the SUPER-D2 function if you select ALC.
1. After selecting ALC, press to open
the ALC CONT menu.
2. Move the cursor to the SUPER-D2
parameter and select ON.
3. If you want to adjust the video output
level, move the cursor to the "I" posi-
tion. Adjust to the desired level by
pressing or .
SETTING PROCEDURES
** ALC CONT **
BACK LIGHT COMP
SUPER-D2 OFF
MASK SET
LEVEL ...I.....
- +
RET END
↵
** ALC CONT **
BACK LIGHT COMP
SUPER-D2 ON
LEVEL ...I.....
- +
RET END
1. Camera Identification (CAMERA ID) Setting
You can use the camera identification (CAMERA ID) to assign a name to the camera. The
camera ID consists of up to 16 alphanumeric characters. The camera ID display can be
selected on or off on the monitor screen.
To edit the CAMERA ID
1. Move the cursor to the CAMERA ID parameter.
2. Press . The CAMERA ID menu appears. The cursor on the letter “0” is highlighted.
3. Move the cursor to the character you
want to edit by pressing / / /
.
4. After selecting the character, press
. The selected character appears
in the editing area. (The pointer in the
editing area moves to the right auto-
matically at this moment.)
5. Repeat the steps above until all char-
acters are edited.
To enter a blank space in the CAMERA ID
Move the cursor to SPACE and press .
To replace a specific character in the CAMERA ID
1. Move the cursor to the editing area by pressing
or
.
2. Move the pointer to the character to be replaced by pressing or . Then move
the cursor to the character area and select a new character.
3. Press to determine the CAMERA ID.
To erase all characters in the editing area
Move the cursor to RESET and press . All characters in the editing area disappear.
To determine the display position of the CAMERA ID
1. Move the cursor to POSI, and press
. The display shown below ap-
pears and the CAMERA ID is highlight-
ed.
WV-CP160
Highlighted
0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$ÄÜÖÆÑÅ
SPACE
POSI RET END RESET
................
Character Cursor
Pointer
Character
Area
Command
Editing
Area
CAMERA ID menu
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
- +
END SET UP ENABLE
↵↵↵
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
- +
END SET UP ENABLE
↵↵↵
2-2. ALC Mode with SUPER-D2 OFF and ELC Mode
Note: If ELC is selected, set MASK SET according to this procedure.
1. Move the cursor to the SUPER-D2
parameter and select OFF. (When you
select ELC, SUPER-D2 is not avail-
able.) The item MASK SET appears on
the menu.
2. Move the cursor to MASK SET and
press . 48 mask areas appear on
the monitor screen. The cursor is blink-
ing in the upper left corner of the
screen.
3. Move the cursor to the area where
backlight is bright and press to
mask that area. The mask turns to
white. (When the cursor is moved on
an area that has already been masked,
the mask and cursor start blinking.)
4. Repeat step 3 to mask the desired
area. To cancel masking, move the
cursor to that area and press .
5. After masking is completed, press
for 2 seconds or more. The ALC CONT
menu appears.
6. If you want to change the video output
level (picture contrast), move the “I”
cursor for LEVEL and adjust the level.
Note: If ON is selected for the SUPER-D2 parameter, a shadow (black line) may appear at
the boundary between the bright and the dim scene. This is a natural phenomenon and
does not indicate trouble.
3. Shutter Speed (SHUTTER)
Move the cursor to the SHUTTER parame-
ter and select the electronic shutter speed.
The preset values for SHUTTER change by
pressing or as shown right.
Note: When ELC is selected for ALC/ELC or ON is selected for SUPER-D2, this item is not
available.
4. Gain Control Setting (AGC ON/OFF)
You can set the gain (brightness level por-
tion of an image) to automatic level adjust-
ment (ON) or fixed level (OFF).
Move the cursor to the AGC parameter and
select automatic level adjustment (ON) or
fixed level (OFF).
Note: If ON is selected for the AGC para-
meter, the noise reduction function is
automatically activated under low light
conditions to reduce noise. In pictures containing a moving object, this may result in an
afterimage.
5. Electronic Sensitivity Enhancement (SENS UP)
There are two modes for SENS UP.
AUTO: If you select X10 AUTO, for
example, the sensitivity is raised
automatically to X10 max. When
AUTO is selected, AGC is auto-
matically set to ON.
FIX: If you select X32 FIX, for example,
the sensitivity is raised to just X32.
Move the cursor to the SENS UP parameter and select the parameter for electronic sensitivi-
ty enhancement.
The preset values for SENS UP (electronic sensitivity enhancement) change by pressing
or as shown at right:
• When OFF is selected for
SUPER-D2 on the CAM SET UP
menu.
• When ON is selected for
SUPER-D2 on the CAM SET UP
menu.
Notes:
• When ON is selected for SUPER-D2 in the ALC CONT menu, FIX is not available for this
item.
• When you select AUTO for SENS UP and ON for SUPER-D2, the SENS UP function has
priority so that the SUPER-D2 function is not activated automatically.
• While the SENS UP function is selected, noise, spots or a whitish phenomenon may
appear in the picture when the sensitivity of the camera is increased. This is a normal
phenomenon.
X2 AUTO
OFF
X4 AUTO X6 AUTO X10 AUTO
X32 FIX X10 FIX X6 FIX X4 FIX X2 FIX
OFF
X16 FIX
** ALC CONT **
BACK LIGHT COMP
SUPER-D2 OFF
MASK SET
LEVEL ...I.....
- +
RET END
↵
Blinking
Blinking
Blinking
Turns to white
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
- +
END SET UP ENABLE
↵↵
↵
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
- +
END SET UP ENABLE
↵↵↵
OFF
X2AUTO
X10AUTO
X6AUTO
X4AUTO
OFF (1/50) 1/120
1/10000 1/4000 1/2000 1/1000
1/250 1/500
6. White Balance Setting (WHITE BAL)
6-1. Auto-Tracing White Balance Mode (ATW)
You can select one of two modes for white balance adjustment as follows:
• ATW (Auto Tracing White Balance)
In this mode, the colour temperature is monitored continuously and thereby white bal-
ance is set automatically. The colour temperature range for the proper white balance is
approximately 2 600 - 6 000K. Proper white balance may not be obtained under the fol-
lowing conditions:
1. The colour temperature is out of
the 2 600 - 6 000K range.
2. When the scene contains mostly
high colour temperature objects,
such as a blue sky or sunset.
3. When the scene is dim.
In these cases, select the AWC
mode.
Move the cursor to the WHITE BAL
parameter and select ATW. The
white balance of the camera is
automatically set.
• Automatic White Balance Control Mode (AWC)
In this mode, accurate white balance is obtained within a colour temperature range of
approximately 2 300-10 000K.
1. Move the cursor to the WHITE BAL
parameter and select AWC→PUSH
SW.
2. Press to start the white bal-
ance setup. The PUSH SW is high-
lighted to indicate that the white
balance is being set.
3. When the white balance setting is completed, the PUSH SW returns to normal dis-
play.
Note: In case that the white balance is not set, the PUSH SW is being highlighted.
4. When you want to adjust the white balance manually, press to select AWC and
press . The AWC menu appears on the monitor. (When ATW is selected, press-
ing displays the ATW menu.)
Fine Adjustment for AWC (ATW) Manually
You can add the detailed setting for white balance setting manually.
1. To set MASK SET, proceed as described in steps 2 to 4 of “ALC mode with SUPER-D2
OFF and ELC mode”.
2. Move the cursor to R.
3. Press or to obtain the optimum amount of red gain.
4. Move the cursor to B.
5. Press or to obtain the optimum amount of blue gain.
Note: When you need to set MASK SET, re-adjust to obtain the optimum amount of red and
blue gain.
7. Audio Level Control (MIC. ON/OFF)
This item is used to adjust the audio level of the sound from microphone.
When the Microphone Selector is set to ON, this function is available.
1. Move the cursor to the AUDIO LEVEL
parameter.
2. Move the “I” cursor to adjust the audio
level.
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
- +
END SET UP ENABLE
↵↵↵
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL AWC
→
PUSH SW
AUDIO LEVEL ....I....
- +
END SET UP ENABLE
↵↵
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL AWC
→
PUSH SW
AUDIO LEVEL ....I....
- +
END SET UP ENABLE
↵↵
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL AWC
AUDIO LEVEL ....I....
- +
END SET UP ENABLE
↵↵↵
** AWC **
R ....I....
- +
B ....I....
- +
MASK SET
RET END
↵
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
- +
END SET UP ENABLE
↵↵↵
8. Special Menu
This menu lets you adjust and set
up the video signal of the camera
to meet your requirements.
Move the cursor to END on the
bottom line of the CAM SET UP
menu and press and
simultaneously (holding down
and press ) for 2 seconds or
more. The SPECIAL menu ap-
pears on the monitor as shown at
right.
8-1. Camera Picture Upside Down Positioning (UP SIDE DOWN)
1. Move the cursor to the UP SIDE DOWN parameter.
2. Select ON when you desire to turn the picture upside down.
8-2. Chroma Level Setting (CHROMA GAIN)
1. Move the cursor to the CHROMA GAIN parameter.
2. While observing the vectorscope or colour video monitor, move the “I” cursor to adjust
the chroma level.
8-3. Aperture Sharpness (Softness) Setting (AP SHARP/AP SOFT)
Note: This item changes according to the position of the detail level selector
(SOFT/SHARP) on the side of the camera.
1. Move the cursor to the AP SHARP (AP SOFT) parameter.
2. While observing the colour video monitor, move the “I” cursor to adjust the aperture
gain level.
8-4. Pedestal Level Setting (PEDESTAL)
1. Move the cursor to the PEDESTAL parameter.
2. While observing the waveform monitor or colour video monitor, move the “I” cursor to
adjust the pedestal level (black level).
To reset to the factory settings (CAMERA RESET)
1. Move the cursor to the CAMERA RESET parameter. PUSH SW is highlighted.
2. While holding down and , press for 2 seconds or more. The camera is reset
to the factory settings.
To close the SPECIAL menu and return to the CAM SET UP menu
Move the cursor to RET and press .
To close the SPECIAL menu and return to the camera picture
Move the cursor to END and press .
** SPECIAL **
UP SIDE DOWN OFF
CHROMA GAIN ....I....
AP SHARP ....I....
PEDESTAL .I.......
CAMERA RESET PUSH SW
RET END
** CAM SET UP **
CAMERA ID OFF
ALC/ELC ALC
SHUTTER OFF
AGC ON
SENS UP OFF
WHITE BAL ATW
AUDIO LEVEL ....I....
- +
END SET UP ENABLE
↵↵↵
Pick-up Device: 752 (H) x 582 (V) pixels, Interline Transfer CCD
Scanning Area: 4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of
1/3” pick-up tube)
Scanning: 625 lines/50 fields/25 frames
Horizontal: 15.625 kHz
Vertical: 50 Hz
Synchronization: Multiplexed Vertical Drive (VD2) by use of specified
camera drive unit.
Video Output: 1.0 V[p-p] PAL composite 75 Ω/through
camera drive unit
Horizontal Resolution: 480 lines
Signal-to-Noise Ratio: 50 dB (AGC OFF, weight ON)
Dynamic Range: 48 dB
Minimum Illumination: 0.4 lx (0.04 footcandle) at F0.75 [Equivalent to 0.8 lx
(0.08 footcandle) at F1.4]
Gain Control: AGC ON or OFF (SET UP MENU) selectable
White Balance: ATW or AWC (SET UP MENU) selectable
Aperture: Set Variable (SET UP MENU) Sharp-Soft selectable by
detail level selector
Electronic Light Control: ALC/ELC
Super Dynamic2: ON or OFF (SET UP MENU) selectable
Electronic Shutter Speed: 1/50 (OFF), 1/120 1/250, 1/500, 1/1 000 1/2 000,
1/4 000, 1/10 000 s selectable
Lens Mount: CS-mount
ALC Lens: DC drive
Ambient Operating Temperature: –10°C - +50°C (14°F - 122°F)
Ambient Operating Humidity: Less than 90 %
Power Source: From the specified monitor or camera drive unit
Power Consumption: 350 mA
Dimensions (without lens): 68 (W) x 65 (H) x 126 (D) mm
[2-11/16” (W) x 2-9/16” (H) x 4-15/16” (D)]
Weights (without lens): 0.375 kg (0.8 lbs.)
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
SPECIFICATIONS
OPTIONAL ACCESSORIES
Lenses : WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3,
WV-LA908C3, WV-LZ61/10, WV-LZ61/15, WV-LZ60/2, WV-LZ62/8
STANDARD ACCESSORIES
Body Cap.......................................................................1 pc.
Camera Mounting Bracket.............................................1 pc.
When the camera is aimed at a bright light, such as a spotlight, or a surface that reflects
bright light, smear or blooming may appear. Therefore, the camera should be operated
carefully in the vicinity of extremely bright objects to avoid smear or blooming.
Bright object
Smear
PREVENTION OF BLOOMING AND SMEAR
Matsushita Electric Industrial Co., Ltd.
Central P.O. Box 288, Osaka 530-91, Japan
2000 © Matsushita Communication Industrial Co., Ltd. All rights reserved.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Panasonic WVCP160 Istruzioni per l'uso
- Categoria
- Telecamere di sicurezza
- Tipo
- Istruzioni per l'uso
in altre lingue
Documenti correlati
Altri documenti
-
Samsung SCC-B2303(P) Manuale utente
-
Honeywell HCD484LX Manuale utente
-
-
-
JVC TK-C655 Manuale utente
-
JVC TK-C1431EG Manuale utente
-
-
-
Audio Technica AT-ONE Istruzioni per l'uso